The purpose of the KVM_SET_SIGNAL_MASK API is to let userspace "kick"
a VCPU out of KVM_RUN through a POSIX signal. A signal is attached
to a dummy signal handler; by blocking the signal outside KVM_RUN and
unblocking it inside, this possible race is closed:
VCPU thread service thread
--------------------------------------------------------------
check flag
set flag
raise signal
(signal handler does nothing)
KVM_RUN
However, one issue with KVM_SET_SIGNAL_MASK is that it has to take
tsk->sighand->siglock on every KVM_RUN. This lock is often on a
remote NUMA node, because it is on the node of a thread's creator.
Taking this lock can be very expensive if there are many userspace
exits (as is the case for SMP Windows VMs without Hyper-V reference
time counter).
As an alternative, we can put the flag directly in kvm_run so that
KVM can see it:
VCPU thread service thread
--------------------------------------------------------------
raise signal
signal handler
set run->immediate_exit
KVM_RUN
check run->immediate_exit
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Numerous MIPS KVM fixes, improvements, and features for 4.11, many of
which continue to pave the way for VZ support, the most interesting of
which are:
- Add GVA->HPA page tables for T&E, to cache GVA mappings.
- Generate fast-path TLB refill exception handler which loads host TLB
entries from GVA page table, avoiding repeated guest memory
translation and guest TLB lookups.
- Use uaccess macros when T&E needs to access guest memory, which with
GVA page tables and the Linux TLB refill handler improves robustness
against TLB faults and fixes EVA hosts.
- Use BadInstr/BadInstrP registers when available to obtain instruction
encodings after a synchronous trap.
- Add GPA->HPA page tables to replace the inflexible linear array,
allowing for multiple sparsely arranged memory regions.
- Properly implement dirty page logging.
- Add KVM_CAP_SYNC_MMU support so that changes in GPA mappings become
effective in guests even if they are already running, allowing for
copy-on-write, KSM, idle page tracking, swapping, and guest memory
ballooning.
- Add KVM_CAP_READONLY_MEM support, so writes to specified memory
regions are treated as MMIO.
- Implement proper CP0_EBase support in T&E.
- Expose a few more missing CP0 registers to userland.
- Add KVM_CAP_NR_VCPUS and KVM_CAP_MAX_VCPUS support, and allow up to 8
VCPUs to be created in a VM.
- Various cleanups and dropping of dead and duplicated code.
-----BEGIN PGP SIGNATURE-----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=lMjW
-----END PGP SIGNATURE-----
Merge tag 'kvm_mips_4.11_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips into HEAD
KVM: MIPS: GVA/GPA page tables, dirty logging, SYNC_MMU etc
Numerous MIPS KVM fixes, improvements, and features for 4.11, many of
which continue to pave the way for VZ support, the most interesting of
which are:
- Add GVA->HPA page tables for T&E, to cache GVA mappings.
- Generate fast-path TLB refill exception handler which loads host TLB
entries from GVA page table, avoiding repeated guest memory
translation and guest TLB lookups.
- Use uaccess macros when T&E needs to access guest memory, which with
GVA page tables and the Linux TLB refill handler improves robustness
against TLB faults and fixes EVA hosts.
- Use BadInstr/BadInstrP registers when available to obtain instruction
encodings after a synchronous trap.
- Add GPA->HPA page tables to replace the inflexible linear array,
allowing for multiple sparsely arranged memory regions.
- Properly implement dirty page logging.
- Add KVM_CAP_SYNC_MMU support so that changes in GPA mappings become
effective in guests even if they are already running, allowing for
copy-on-write, KSM, idle page tracking, swapping, and guest memory
ballooning.
- Add KVM_CAP_READONLY_MEM support, so writes to specified memory
regions are treated as MMIO.
- Implement proper CP0_EBase support in T&E.
- Expose a few more missing CP0 registers to userland.
- Add KVM_CAP_NR_VCPUS and KVM_CAP_MAX_VCPUS support, and allow up to 8
VCPUs to be created in a VM.
- Various cleanups and dropping of dead and duplicated code.
Expose the CP0_IntCtl register through the KVM register access API,
which is a required register since MIPS32r2. It is currently read-only
since the VS field isn't implemented due to lack of Config3.VInt or
Config3.VEIC.
It is implemented in trap_emul.c so that a VZ implementation can allow
writes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Expose the CP0_EntryLo0 and CP0_EntryLo1 registers through the KVM
register access API. This is fairly straightforward for trap & emulate
since we don't support the RI and XI bits. For the sake of future
proofing (particularly for VZ) it is explicitly specified that the API
always exposes the 64-bit version of these registers (i.e. with the RI
and XI bits in bit positions 63 and 62 respectively), and they are
implemented in trap_emul.c rather than mips.c to allow them to be
implemented differently for VZ.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The CP0_EBase register is a standard feature of MIPS32r2, so we should
always have been implementing it properly. However the register value
was ignored and wasn't exposed to userland.
Fix the emulation of exceptions and interrupts to use the value stored
in guest CP0_EBase, and fix the masks so that the top 3 bits (rather
than the standard 2) are fixed, so that it is always in the guest KSeg0
segment.
Also add CP0_EBASE to the KVM one_reg interface so it can be accessed by
userland, also allowing the CPU number field to be written (which isn't
permitted by the guest).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The KVM_PPC_ALLOCATE_HTAB ioctl() is used to set the size of hashed page
table (HPT) that userspace expects a guest VM to have, and is also used to
clear that HPT when necessary (e.g. guest reboot).
At present, once the ioctl() is called for the first time, the HPT size can
never be changed thereafter - it will be cleared but always sized as from
the first call.
With upcoming HPT resize implementation, we're going to need to allow
userspace to resize the HPT at reset (to change it back to the default size
if the guest changed it).
So, we need to allow this ioctl() to change the HPT size.
This patch also updates Documentation/virtual/kvm/api.txt to reflect
the new behaviour. In fact the documentation was already slightly
incorrect since 572abd5 "KVM: PPC: Book3S HV: Don't fall back to
smaller HPT size in allocation ioctl"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a new powerpc-specific KVM_CAP_SPAPR_RESIZE_HPT capability to
advertise whether KVM is capable of handling the PAPR extensions for
resizing the hashed page table during guest runtime. It also adds
definitions for two new VM ioctl()s to implement this extension, and
documentation of the same.
Note that, HPT resizing is already possible with KVM PR without kernel
modification, since the HPT is managed within userspace (qemu). The
capability defined here will only be set where an in-kernel implementation
of resizing is necessary, i.e. for KVM HV. To determine if the userspace
resize implementation can be used, it's necessary to check
KVM_CAP_PPC_ALLOC_HTAB. Unfortunately older kernels incorrectly set
KVM_CAP_PPC_ALLOC_HTAB even with KVM PR. If userspace it want to support
resizing with KVM PR on such kernels, it will need a workaround.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Both KVM_CREATE_SPAPR_TCE_64 and KVM_REINJECT_CONTROL have section number
4.98 in Documentation/virtual/kvm/api.txt, presumably due to a naive merge.
This corrects the duplication.
[paulus@ozlabs.org - correct section numbers for following sections,
KVM_PPC_CONFIGURE_V3_MMU and KVM_PPC_GET_RMMU_INFO, as well.]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest. The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables. (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).
The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.
The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU. It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.
Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zxXl
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.10:
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Userspace can read the exact value of kvmclock by reading the TSC
and fetching the timekeeping parameters out of guest memory. This
however is brittle and not necessary anymore with KVM 4.11. Provide
a mechanism that lets userspace know if the new KVM_GET_CLOCK
semantics are in effect, and---since we are at it---if the clock
is stable across all VCPUs.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The KVM_X2APIC_API_USE_32BIT_IDS feature applies to both
KVM_SET_GSI_ROUTING and KVM_SIGNAL_MSI, but was not mentioned in the
documentation for the latter ioctl.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXoydqAAoJEEtpOizt6ddyM3oH/1A4VeG/J9q4fBPXqY2tVWXs
c3P7UgNcrEgUNs/F9ykQY/lb31deecUzaBt1OyTf+RlsNbihq3dQdYcBhxtUODw/
Faok582ya3UFgLW+IRHcID0EbkVOpIzMhOStYsnU/Dz7HG1JL9HdPzwkid7iu9LT
fI6yrrBnJFjdWAAQ4BkcEKBENRsY8NTs7jX5vnFA92MkUBby7BmariPDD3FtrB+f
Ob9B7CxM30pNqsN7OA/QvFOHMJHxf3s1TBKwmPHe5TLIfSzV1YxcEGiMc0lWqF4v
BT8ZeMGCtjDw94tND1DskfQQRPaMqPmGuRTrAW/IuE2n92bFtbqIqs7Cbw0fzLE=
=Vm6Q
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.8 - Take 2
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXkk6wAAoJECPQ0LrRPXpDkIQP/iJ2yXTxrfbJoyaVq1vuMn3R
UFhVwNXP8OEjQrmp5lvMBazB1MRBkNDzlVXL1fSb+ijKmbIELOqHhO6ijrkK4zmc
0Ie0x5Bt4gIFPTZyZORVpy1eU/0YFGWERAfsAjYdMCeKwHjaUCRSrZBXF2YsFTfo
Hh/ILvHa8TjUXWsQXvtZCL6AAnkDKBsbDWqsq5zspuT+PA8umI+dGLIiULXBpc4t
S2TCDxOU1JgsAn+Y0XVbPXV9id+bs5LRd6nNH/RmipIVqWmukSrScXOjg/po/l2S
laO4tHmyEeN6ecnCxWttpjacNwyTDNh5n3lL1ceBnBZFqn1k/7NjqV3fQzJxGd1T
1U6edE9+EuS9uXWF5XcEuAD660EiMs4FLVSjPgqYQtto3gOHilmuWL9eeeOOgCem
Lknnu/7G8h36PaQuLnEXWXQb7jeS2rTuC0RqxCG62gD9UWEJTckRz5pRh/e6gz7n
ZVXMrwGiVZ3zR78qE6i2j5CZ6A0BMAK3nZ85AI3kmgKg0CfVY28uPOj8llAOaYm+
0XVdfRj7ed75eu3GobjHUyZ0fQ40jovmH2vy3mupBm5XBUHgH/j6X510KJ1UTLWI
C2EO9KogbjoVeu60mQi4bKGSPi8/wdgYqVft/Qzl5D5iFvQ7Ia+TQNMArCQazBID
Ihe1E09NGrHjV3Yw/GWV
=2Del
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM changes for Linux 4.8
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
Up to now, only irqchip routing entries could be set. This patch
adds the capability to insert MSI routing entries.
For ARM64, let's also increase KVM_MAX_IRQ_ROUTES to 4096: this
include SPI irqchip routes plus MSI routes. In the future this
might be extended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds compilation and link against irqchip.
Main motivation behind using irqchip code is to enable MSI
routing code. In the future irqchip routing may also be useful
when targeting multiple irqchips.
Routing standard callbacks now are implemented in vgic-irqfd:
- kvm_set_routing_entry
- kvm_set_irq
- kvm_set_msi
They only are supported with new_vgic code.
Both HAVE_KVM_IRQCHIP and HAVE_KVM_IRQ_ROUTING are defined.
KVM_CAP_IRQ_ROUTING is advertised and KVM_SET_GSI_ROUTING is allowed.
So from now on IRQCHIP routing is enabled and a routing table entry
must exist for irqfd injection to succeed for a given SPI. This patch
builds a default flat irqchip routing table (gsi=irqchip.pin) covering
all the VGIC SPI indexes. This routing table is overwritten by the
first first user-space call to KVM_SET_GSI_ROUTING ioctl.
MSI routing setup is not yet allowed.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On ARM, the MSI msg (address and data) comes along with
out-of-band device ID information. The device ID encodes the
device that writes the MSI msg. Let's convey the device id in
kvm_irq_routing_msi and use KVM_MSI_VALID_DEVID flag value in
kvm_irq_routing_entry to indicate the msi devid is populated.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM GICv3 ITS MSI controller requires a device ID to be able to
assign the proper interrupt vector. On real hardware, this ID is
sampled from the bus. To be able to emulate an ITS controller, extend
the KVM MSI interface to let userspace provide such a device ID. For
PCI devices, the device ID is simply the 16-bit bus-device-function
triplet, which should be easily available to the userland tool.
Also there is a new KVM capability which advertises whether the
current VM requires a device ID to be set along with the MSI data.
This flag is still reported as not available everywhere, later we will
enable it when ITS emulation is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We will use illegal instruction 0x0000 for handling 2 byte sw breakpoints
from user space. As it can be enabled dynamically via a capability,
let's move setting of ICTL_OPEREXC to the post creation step, so we avoid
any races when enabling that capability just while adding new cpus.
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK as a feature flag to
KVM_CAP_X2APIC_API.
The quirk made KVM interpret 0xff as a broadcast even in x2APIC mode.
The enableable capability is needed in order to support standard x2APIC and
remain backward compatible.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Expand kvm_apic_mda comment. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_CAP_X2APIC_API is a capability for features related to x2APIC
enablement. KVM_X2APIC_API_32BIT_FORMAT feature can be enabled to
extend APIC ID in get/set ioctl and MSI addresses to 32 bits.
Both are needed to support x2APIC.
The feature has to be enableable and disabled by default, because
get/set ioctl shifted and truncated APIC ID to 8 bits by using a
non-standard protocol inspired by xAPIC and the change is not
backward-compatible.
Changes to MSI addresses follow the format used by interrupt remapping
unit. The upper address word, that used to be 0, contains upper 24 bits
of the LAPIC address in its upper 24 bits. Lower 8 bits are reserved as
0. Using the upper address word is not backward-compatible either as we
didn't check that userspace zeroed the word. Reserved bits are still
not explicitly checked, but non-zero data will affect LAPIC addresses,
which will cause a bug.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow up to 6 KVM guest KScratch registers to be enabled and accessed
via the KVM guest register API and from the guest itself (the fallback
reading and writing of commpage registers is sufficient for KScratch
registers to work as expected).
User mode can expose the registers by setting the appropriate bits of
the guest Config4.KScrExist field. KScratch registers that aren't usable
won't be writeable via the KVM Ioctl API.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's not provide the device attribute for cmma enabling and clearing
if the hardware doesn't support it.
This also helps getting rid of the undocumented return value "-EINVAL"
in case CMMA is not available when trying to enable it.
Also properly document the meaning of -EINVAL for CMMA clearing.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.
This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.
The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.
This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We forgot to document that capability, let's add documentation.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rpvb
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.6
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
Conflicts:
include/uapi/linux/kvm.h
The highlights are:
* Enable VFIO device on PowerPC, from David Gibson
* Optimizations to speed up IPIs between vcpus in HV KVM,
from Suresh Warrier (who is also Suresh E. Warrier)
* In-kernel handling of IOMMU hypercalls, and support for dynamic DMA
windows (DDW), from Alexey Kardashevskiy.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing KVM_CREATE_SPAPR_TCE only supports 32bit windows which is not
enough for directly mapped windows as the guest can get more than 4GB.
This adds KVM_CREATE_SPAPR_TCE_64 ioctl and advertises it
via KVM_CAP_SPAPR_TCE_64 capability. The table size is checked against
the locked memory limit.
Since 64bit windows are to support Dynamic DMA windows (DDW), let's add
@bus_offset and @page_shift which are also required by DDW.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some cases it needs to get/set attributes specific to a vcpu and so
needs something else than ONE_REG.
Let's copy the KVM_DEVICE approach, and define the respective ioctls
for the vcpu file descriptor.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To support guest PMUv3, use one bit of the VCPU INIT feature array.
Initialize the PMU when initialzing the vcpu with that bit and PMU
overflow interrupt set.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds real and virtual mode handlers for the H_PUT_TCE_INDIRECT and
H_STUFF_TCE hypercalls for user space emulated devices such as IBMVIO
devices or emulated PCI. These calls allow adding multiple entries
(up to 512) into the TCE table in one call which saves time on
transition between kernel and user space.
The current implementation of kvmppc_h_stuff_tce() allows it to be
executed in both real and virtual modes so there is one helper.
The kvmppc_rm_h_put_tce_indirect() needs to translate the guest address
to the host address and since the translation is different, there are
2 helpers - one for each mode.
This implements the KVM_CAP_PPC_MULTITCE capability. When present,
the kernel will try handling H_PUT_TCE_INDIRECT and H_STUFF_TCE if these
are enabled by the userspace via KVM_CAP_PPC_ENABLE_HCALL.
If they can not be handled by the kernel, they are passed on to
the user space. The user space still has to have an implementation
for these.
Both HV and PR-syle KVM are supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The KVM_SMI capability is following the KVM_S390_SET_IRQ_STATE capability
which is "4.95", this changes the number of the KVM_SMI chapter to 4.96.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A new vcpu exit is introduced to notify the userspace of the
changes in Hyper-V SynIC configuration triggered by guest writing to the
corresponding MSRs.
Changes v4:
* exit into userspace only if guest writes into SynIC MSR's
Changes v3:
* added KVM_EXIT_HYPERV types and structs notes into docs
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynIC (synthetic interrupt controller) is a lapic extension,
which is controlled via MSRs and maintains for each vCPU
- 16 synthetic interrupt "lines" (SINT's); each can be configured to
trigger a specific interrupt vector optionally with auto-EOI
semantics
- a message page in the guest memory with 16 256-byte per-SINT message
slots
- an event flag page in the guest memory with 16 2048-bit per-SINT
event flag areas
The host triggers a SINT whenever it delivers a new message to the
corresponding slot or flips an event flag bit in the corresponding area.
The guest informs the host that it can try delivering a message by
explicitly asserting EOI in lapic or writing to End-Of-Message (EOM)
MSR.
The userspace (qemu) triggers interrupts and receives EOM notifications
via irqfd with resampler; for that, a GSI is allocated for each
configured SINT, and irq_routing api is extended to support GSI-SINT
mapping.
Changes v4:
* added activation of SynIC by vcpu KVM_ENABLE_CAP
* added per SynIC active flag
* added deactivation of APICv upon SynIC activation
Changes v3:
* added KVM_CAP_HYPERV_SYNIC and KVM_IRQ_ROUTING_HV_SINT notes into
docs
Changes v2:
* do not use posted interrupts for Hyper-V SynIC AutoEOI vectors
* add Hyper-V SynIC vectors into EOI exit bitmap
* Hyper-V SyniIC SINT msr write logic simplified
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
handling.
PPC: Mostly bug fixes.
ARM: No big features, but many small fixes and prerequisites including:
- a number of fixes for the arch-timer
- introducing proper level-triggered semantics for the arch-timers
- a series of patches to synchronously halt a guest (prerequisite for
IRQ forwarding)
- some tracepoint improvements
- a tweak for the EL2 panic handlers
- some more VGIC cleanups getting rid of redundant state
x86: quite a few changes:
- support for VT-d posted interrupts (i.e. PCI devices can inject
interrupts directly into vCPUs). This introduces a new component (in
virt/lib/) that connects VFIO and KVM together. The same infrastructure
will be used for ARM interrupt forwarding as well.
- more Hyper-V features, though the main one Hyper-V synthetic interrupt
controller will have to wait for 4.5. These will let KVM expose Hyper-V
devices.
- nested virtualization now supports VPID (same as PCID but for vCPUs)
which makes it quite a bit faster
- for future hardware that supports NVDIMM, there is support for clflushopt,
clwb, pcommit
- support for "split irqchip", i.e. LAPIC in kernel + IOAPIC/PIC/PIT in
userspace, which reduces the attack surface of the hypervisor
- obligatory smattering of SMM fixes
- on the guest side, stable scheduler clock support was rewritten to not
require help from the hypervisor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWO2IQAAoJEL/70l94x66D/K0H/3AovAgYmJQToZlimsktMk6a
f2xhdIqfU5lIQQh5uNBCfL3o9o8H9Py1ym7aEw3fmztPHHJYc91oTatt2UEKhmEw
VtZHp/dFHt3hwaIdXmjRPEXiYctraKCyrhaUYdWmUYkoKi7lW5OL5h+S7frG2U6u
p/hFKnHRZfXHr6NSgIqvYkKqtnc+C0FWY696IZMzgCksOO8jB1xrxoSN3tANW3oJ
PDV+4og0fN/Fr1capJUFEc/fejREHneANvlKrLaa8ht0qJQutoczNADUiSFLcMPG
iHljXeDsv5eyjMtUuIL8+MPzcrIt/y4rY41ZPiKggxULrXc6H+JJL/e/zThZpXc=
=iv2z
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.4.
s390:
A bunch of fixes and optimizations for interrupt and time handling.
PPC:
Mostly bug fixes.
ARM:
No big features, but many small fixes and prerequisites including:
- a number of fixes for the arch-timer
- introducing proper level-triggered semantics for the arch-timers
- a series of patches to synchronously halt a guest (prerequisite
for IRQ forwarding)
- some tracepoint improvements
- a tweak for the EL2 panic handlers
- some more VGIC cleanups getting rid of redundant state
x86:
Quite a few changes:
- support for VT-d posted interrupts (i.e. PCI devices can inject
interrupts directly into vCPUs). This introduces a new
component (in virt/lib/) that connects VFIO and KVM together.
The same infrastructure will be used for ARM interrupt
forwarding as well.
- more Hyper-V features, though the main one Hyper-V synthetic
interrupt controller will have to wait for 4.5. These will let
KVM expose Hyper-V devices.
- nested virtualization now supports VPID (same as PCID but for
vCPUs) which makes it quite a bit faster
- for future hardware that supports NVDIMM, there is support for
clflushopt, clwb, pcommit
- support for "split irqchip", i.e. LAPIC in kernel +
IOAPIC/PIC/PIT in userspace, which reduces the attack surface of
the hypervisor
- obligatory smattering of SMM fixes
- on the guest side, stable scheduler clock support was rewritten
to not require help from the hypervisor"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (123 commits)
KVM: VMX: Fix commit which broke PML
KVM: x86: obey KVM_X86_QUIRK_CD_NW_CLEARED in kvm_set_cr0()
KVM: x86: allow RSM from 64-bit mode
KVM: VMX: fix SMEP and SMAP without EPT
KVM: x86: move kvm_set_irq_inatomic to legacy device assignment
KVM: device assignment: remove pointless #ifdefs
KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
KVM: x86: zero apic_arb_prio on reset
drivers/hv: share Hyper-V SynIC constants with userspace
KVM: x86: handle SMBASE as physical address in RSM
KVM: x86: add read_phys to x86_emulate_ops
KVM: x86: removing unused variable
KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
KVM: arm/arm64: Optimize away redundant LR tracking
KVM: s390: use simple switch statement as multiplexer
KVM: s390: drop useless newline in debugging data
KVM: s390: SCA must not cross page boundaries
KVM: arm: Do not indent the arguments of DECLARE_BITMAP
...
This patch fix spelling typos in Documentation/virtual/kvm.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to enable userspace PIC support, the userspace PIC needs to
be able to inject local interrupts even when the APICs are in the
kernel.
KVM_INTERRUPT now supports sending local interrupts to an APIC when
APICs are in the kernel.
The ready_for_interrupt_request flag is now only set when the CPU/APIC
will immediately accept and inject an interrupt (i.e. APIC has not
masked the PIC).
When the PIC wishes to initiate an INTA cycle with, say, CPU0, it
kicks CPU0 out of the guest, and renedezvous with CPU0 once it arrives
in userspace.
When the CPU/APIC unmasks the PIC, a KVM_EXIT_IRQ_WINDOW_OPEN is
triggered, so that userspace has a chance to inject a PIC interrupt
if it had been pending.
Overall, this design can lead to a small number of spurious userspace
renedezvous. In particular, whenever the PIC transistions from low to
high while it is masked and whenever the PIC becomes unmasked while
it is low.
Note: this does not buffer more than one local interrupt in the
kernel, so the VMM needs to enter the guest in order to complete
interrupt injection before injecting an additional interrupt.
Compiles for x86.
Can pass the KVM Unit Tests.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to support a userspace IOAPIC interacting with an in kernel
APIC, the EOI exit bitmaps need to be configurable.
If the IOAPIC is in userspace (i.e. the irqchip has been split), the
EOI exit bitmaps will be set whenever the GSI Routes are configured.
In particular, for the low MSI routes are reservable for userspace
IOAPICs. For these MSI routes, the EOI Exit bit corresponding to the
destination vector of the route will be set for the destination VCPU.
The intention is for the userspace IOAPICs to use the reservable MSI
routes to inject interrupts into the guest.
This is a slight abuse of the notion of an MSI Route, given that MSIs
classically bypass the IOAPIC. It might be worthwhile to add an
additional route type to improve clarity.
Compile tested for Intel x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adds KVM_EXIT_IOAPIC_EOI which allows the kernel to EOI
level-triggered IOAPIC interrupts.
Uses a per VCPU exit bitmap to decide whether or not the IOAPIC needs
to be informed (which is identical to the EOI_EXIT_BITMAP field used
by modern x86 processors, but can also be used to elide kvm IOAPIC EOI
exits on older processors).
[Note: A prototype using ResampleFDs found that decoupling the EOI
from the VCPU's thread made it possible for the VCPU to not see a
recent EOI after reentering the guest. This does not match real
hardware.]
Compile tested for Intel x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
First patch in a series which enables the relocation of the
PIC/IOAPIC to userspace.
Adds capability KVM_CAP_SPLIT_IRQCHIP;
KVM_CAP_SPLIT_IRQCHIP enables the construction of LAPICs without the
rest of the irqchip.
Compile tested for x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Suggested-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Luiz Capitulino