As long as the value is 0 the feature is disabled. With setting
it to a positive value, DRBD limits and aligns its resync requests
to the rs-discard-granularity setting. If the sync source detects
all zeros in such a block, the resync target discards the range
on disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In setups involving a DRBD-proxy and connections that experience a lot of
buffer-bloat it might be necessary to set ping-timeout to an
unusual high value. By default DRBD uses the same value to wait if a newly
established TCP-connection is stable. Since the DRBD-proxy is usually located
in the same data center such a long wait time may hinder DRBD's connect process.
In such setups socket-check-timeout should be set to
at least to the round trip time between DRBD and DRBD-proxy. I.e. in most
cases to 1.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Checksum based resync trades CPU cycles for network bandwidth,
in situations where we expect much of the to-be-resynced blocks
to be actually identical on both sides already.
In a "network hickup" scenario, it won't help:
all to-be-resynced blocks will typically be different.
The use case is for the resync of *potentially* different blocks
after crash recovery -- the crash recovery had marked larger areas
(those covered by the activity log) as need-to-be-resynced,
just in case. Most of those blocks will be identical.
This option makes it possible to configure checksum based resync,
but only actually use it for the first resync after primary crash.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow to change the AL layout with an resize operation. For that
the reisze command gets two new fields: al_stripes and al_stripe_size.
In order to make the operation crash save:
1) Lock out all IO and MD-IO
2) Write the super block with MDF_PRIMARY_IND clear
3) write the bitmap to the new location (all zeros, since
we allow only while connected)
4) Initialize the new AL-area
5) Write the super block with the restored MDF_PRIMARY_IND.
6) Unfreeze all IO
Since the AL-layout has no influence on the protocol, this operation
needs to be beforemed on both sides of a resource (if intended).
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the on-disk activity-log ring buffer size is adjustable,
the maximum active set can become larger, and is now limited by
the use of 16bit "labels".
This increases the maximum working set from 6433 to 65534 extents,
each of which covers an area of 4MiB.
Which means that if you use the maximum, you'd have to resync
more than 250 GiB after an unclean Primary shutdown.
With capable backend storage and replication links,
this is entirely feasible.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By disabling al-updates one might increase performace. The price for
that is that in case a crashed primary (that had al-updates disabled)
is reintegraded, it will receive a full-resync instead of a bitmap
based resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
New config option for the disk secition "read-balancing", with
the values: prefer-local, prefer-remote, round-robin, when-congested-remote.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* The max of minor_count is 255
* In drbdadm count the number of minors, instead of finding
the highest minor number
* No longer us the magic in the init script
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The maximum minor device number allowed by the kernel is (1<<20 - 1). Reject
device numbers higher than that to earlier catch possible errors.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Enabled the resync controller, with a fill target of 50Kib. That gives
reasonable resync speeds without tuning. A much better default than
the 250KiB/s fixed.
* Enable bitmap compression. It is save to use, and most people have
more CPU power than network bandwidth.
* ko-count of 7: Abort a connection if the peer fails to process a
write request within 42 seconds.
* al-extents of 1237: ~5 GiB seems to be a much more sane default
these days.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* drbd-8.3:
documentation: Documented detach's --force and disk's --disk-timeout
drbd: Implemented the disk-timeout option
drbd: Force flag for the detach operation
drbd: Allow new IOs while the local disk in in FAILED state
drbd: Bitmap IO functions can not return prematurely if the disk breaks
drbd: Added a kref to bm_aio_ctx
drbd: Hold a reference to ldev while doing meta-data IO
drbd: Keep a reference to the bio until the completion handler finished
drbd: Implemented wait_until_done_or_disk_failure()
drbd: Replaced md_io_mutex by an atomic: md_io_in_use
drbd: moved md_io into mdev
drbd: Immediately allow completion of IOs, that wait for IO completions on a failed disk
drbd: Keep a reference to barrier acked requests
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* commit 'ae57a0a':
drbd: Only print sanitize state's warnings, if the state change happens
drbd: we should write meta data updates with FLUSH FUA
drbd: fix limit define, we support 1 PiByte now
drbd: fix log message argument order
drbd: Typo in user-visible message.
drbd: Make "(rcv|snd)buf-size" and "ping-timeout" available for the proxy, too.
drbd: Allow keywords to be used in multiple config sections.
drbd: fix typos in comments.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow up to 300 centi-seconds to be configured for the "ping timeout".
There may be setups where heavy congestion, huge buffers, and asymmetric
bandwidth limitations may need a "huge" ping-timeout as work-around
for "spurious connection loss" problems.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
These constants are useful for the same purpose in more than one place.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We don't have the units in constant names in other places, either.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 32-bit resync_after netlink field takes a device minor number as
parameter, which is no longer limited to 255. We cannot statically
verify which device numbers are valid, so set the ummer limit to the
highest possible signed 32-bit integer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 8 byte header finally becomes too small. With the protocol 100 header we
have 16 bit for the volume number, proper 32 bit for the data length, and
32 bit for further extensions in the future.
Previous versions of drbd are using version 80 headers for all packets
short enough for protocol 80. They support both header versions in
worker context, but only version 80 headers in asynchronous context.
For backwards compatibility, continue to use version 80 headers for
short packets before protocol version 100.
From protocol version 100 on, use the same header version for all
packets.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit breaks the API again.
Move per-volume former syncer options into disk_conf.
Move per-connection former syncer options into net_conf.
Renamed the remainign sync_conf to res_opts
Syncer settings have been changeable at runtime, so we need to prepare
for these settings to be runtime-changeable in their new home as well.
Introduce new configuration operations, and share the netlink attribute
between "attach" (create new disk) and "disk-opts" (change options).
Same for "connect" and "net-opts".
Some fields cannot be changed at runtime, however.
Introduce a new flag GENLA_F_INVARIANT to be able to trigger on that in
the generated validation and assignment functions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Old default behaviour was "pass-on",
which is not useful in production at all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Use a new on-disk transaction format for the activity log, which allows
for multiple changes to the active set per transaction.
Using 4k transaction blocks, we can now get rid of the work-around code
to deal with devices not supporting 512 byte logical block size.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Connections through a compressing proxy might have more bits
on the fly. 500MByte instead of 50MByte
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We now track the data rate of locally submitted resync related requests,
and can thus detect non-resync activity on the lower level device.
If the current sync rate is above c-min-rate, and the lower level device
appears to be busy, we throttle the resyncer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When no data is accessible (no connection to the peer, nor a local disk)
allow the user to select to freeze all IO operations instead of getting
IO errors.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To reasonably control resync speed over drbd-proxy connections,
drbd has to measure the current delay of packets transmitted over
the (possibly congested) data socket vs the meta-data socket.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>