Keep track of rxrpc_call structures in a hashtable so they can be
found directly from the network parameters which define the call.
This allows incoming packets to be routed directly to a call without walking
through hierarchy of peer -> transport -> connection -> call and all the
spinlocks that that entailed.
Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Set the RxRPC header flag to request an ACK packet for every odd-numbered DATA
packet unless it's the last one (which implicitly requests an ACK anyway).
This is similar to how librx appears to work.
If we don't do this, we'll send out a full window of packets and then just sit
there until the other side gets bored and sends an ACK to indicate that it's
been idle for a while and has received no new packets.
Requesting a lot of ACKs shouldn't be a problem as ACKs should be merged when
possible.
As AF_RXRPC currently works, it will schedule an ACK to be generated upon
receipt of a DATA packet with the ACK-request packet set - and in the time
taken to schedule this in a work queue, several other packets are likely to
arrive and then all get ACK'd together.
Signed-off-by: David Howells <dhowells@redhat.com>
Expose RxRPC parameters via sysctls to control the Rx window size, the Rx MTU
maximum size and the number of packets that can be glued into a jumbo packet.
More info added to Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
Improve ACK production by the following means:
(1) Don't send an ACK_REQUESTED ack immediately even if the RXRPC_MORE_PACKETS
flag isn't set on a data packet that has also has RXRPC_REQUEST_ACK set.
MORE_PACKETS just means that the sender just emptied its Tx data buffer.
More data will be forthcoming unless RXRPC_LAST_PACKET is also flagged.
It is possible to see runs of DATA packets with MORE_PACKETS unset that
aren't waiting for an ACK.
It is therefore better to wait a small instant to see if we can combine an
ACK for several packets.
(2) Don't send an ACK_IDLE ack immediately unless we're responding to the
terminal data packet of a call.
Whilst sending an ACK_IDLE mid-call serves to let the other side know
that we won't be asking it to resend certain Tx buffers and that it can
discard them, spamming it with loads of acks just because we've
temporarily run out of data just distracts it.
(3) Put the ACK_IDLE ack generation timeout up to half a second rather than a
single jiffy. Just because we haven't been given more data immediately
doesn't mean that more isn't forthcoming. The other side may be busily
finding the data to send to us.
Signed-off-by: David Howells <dhowells@redhat.com>
Add sysctls for configuring RxRPC protocol handling, specifically controls on
delays before ack generation, the delay before resending a packet, the maximum
lifetime of a call and the expiration times of calls, connections and
transports that haven't been recently used.
More info added in Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
AF_RXRPC sends UDP packets with the "Don't Fragment" bit set in an attempt to
determine the maximum packet size between the local socket and the peer by
invoking the generation of ICMP_FRAG_NEEDED packets.
Once a packet is sent with the "Don't Fragment" bit set, it is then
inconvenient to break it up as that requires recalculating all the rxrpc serial
and sequence numbers and reencrypting all the fragments, so we switch off the
"Don't Fragment" service temporarily and send the bounced packet again. Future
packets then use the new MTU.
That's all fine. The problem lies in rxrpc_UDP_error_report() where the code
that deals with ICMP_FRAG_NEEDED packets lives. Packets of this type have a
field (ee_info) to indicate the maximum packet size at the reporting node - but
sometimes ee_info isn't filled in and is just left as 0 and the code must allow
for this.
When ee_info is 0, the code should take the MTU size we're currently using and
reduce it for the next packet we want to send. However, it takes ee_info
(which is known to be 0) and tries to reduce that instead.
This was discovered by Coverity.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
When an ABORT is sent, aborting a connection, the sender quite reasonably
forgets about the connection. If another frame is received, another ABORT
will be sent. When the receiver gets it, it no longer applies to an extant
connection, so an ABORT is sent, and so on...
Prevent this by never sending a rejection for an ABORT packet.
Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
The UDP checksum was already verified in rxrpc_data_ready() - which calls
skb_checksum_complete() - as the RxRPC packet header contains no checksum of
its own. Subsequent calls to skb_copy_and_csum_datagram_iovec() are thus
redundant and are, in any case, being passed only a subset of the UDP payload -
so the checksum will always fail if that path is taken.
So there is no need to check skb->ip_summed in rxrpc_recvmsg(), and no need for
the csum_copy_error: exit path.
Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=igX7
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-20140126' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
RxRPC fixes
Here are some small AF_RXRPC fixes.
(1) Fix a place where a spinlock is taken conditionally but is released
unconditionally.
(2) Fix a double-free that happens when cleaning up on a checksum error.
(3) Fix handling of CHECKSUM_PARTIAL whilst delivering messages to userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On input, CHECKSUM_PARTIAL should be treated the same way as
CHECKSUM_UNNECESSARY. See include/linux/skbuff.h
Signed-off-by: Tim Smith <tim@electronghost.co.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
If rx->conn is not NULL, rxrpc_connect_exclusive() does not
acquire the transport's client lock, but it still releases it.
The patch adds locking of the spinlock to this path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Smatch complains because we are using an untrusted index into the
rxrpc_acks[] array. It's just a read and it's only in the debug code,
but it's simple enough to add a check and fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch to f3d3342602 ("net: rework recvmsg
handler msg_name and msg_namelen logic").
DECLARE_SOCKADDR validates that the structure we use for writing the
name information to is not larger than the buffer which is reserved
for msg->msg_name (which is 128 bytes). Also use DECLARE_SOCKADDR
consistently in sendmsg code paths.
Signed-off-by: Steffen Hurrle <steffen@hurrle.net>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Give the key type the opportunity to preparse the payload prior to the
instantiation and update routines being called. This is done with the
provision of two new key type operations:
int (*preparse)(struct key_preparsed_payload *prep);
void (*free_preparse)(struct key_preparsed_payload *prep);
If the first operation is present, then it is called before key creation (in
the add/update case) or before the key semaphore is taken (in the update and
instantiate cases). The second operation is called to clean up if the first
was called.
preparse() is given the opportunity to fill in the following structure:
struct key_preparsed_payload {
char *description;
void *type_data[2];
void *payload;
const void *data;
size_t datalen;
size_t quotalen;
};
Before the preparser is called, the first three fields will have been cleared,
the payload pointer and size will be stored in data and datalen and the default
quota size from the key_type struct will be stored into quotalen.
The preparser may parse the payload in any way it likes and may store data in
the type_data[] and payload fields for use by the instantiate() and update()
ops.
The preparser may also propose a description for the key by attaching it as a
string to the description field. This can be used by passing a NULL or ""
description to the add_key() system call or the key_create_or_update()
function. This cannot work with request_key() as that required the description
to tell the upcall about the key to be created.
This, for example permits keys that store PGP public keys to generate their own
name from the user ID and public key fingerprint in the key.
The instantiate() and update() operations are then modified to look like this:
int (*instantiate)(struct key *key, struct key_preparsed_payload *prep);
int (*update)(struct key *key, struct key_preparsed_payload *prep);
and the new payload data is passed in *prep, whether or not it was preparsed.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In net/dns_resolver/dns_key.c and net/rxrpc/ar-key.c make them
work with user namespaces enabled where key_alloc takes kuids and kgids.
Pass GLOBAL_ROOT_UID and GLOBAL_ROOT_GID instead of bare 0's.
Cc: Sage Weil <sage@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: linux-afs@lists.infradead.org
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If list_for_each_entry, etc complete a traversal of the list, the iterator
variable ends up pointing to an address at an offset from the list head,
and not a meaningful structure. Thus this value should not be used after
the end of the iterator. This seems to be a copy-paste bug from a previous
debugging message, and so the meaningless value is just deleted.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
I backed off from trying to just eliminate this variable, since
transforming atomic_inc_return() into atomic_inc() takes away
the memory barriers.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a key type operation to permit the key type to vet the description of a new
key that key_alloc() is about to allocate. The operation may reject the
description if it wishes with an error of its choosing. If it does this, the
key will not be allocated.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
MAINTAINERS: Add Andy Gospodarek as co-maintainer.
r8169: disable ASPM
RxRPC: Fix v1 keys
AF_RXRPC: Handle receiving ACKALL packets
cnic: Fix lost interrupt on bnx2x
cnic: Prevent status block race conditions with hardware
net: dcbnl: check correct ops in dcbnl_ieee_set()
e1000e: disable broken PHY wakeup for ICH10 LOMs, use MAC wakeup instead
igb: fix sparse warning
e1000: fix sparse warning
netfilter: nf_log: avoid oops in (un)bind with invalid nfproto values
dccp: fix oops on Reset after close
ipvs: fix dst_lock locking on dest update
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
bnx2x: update driver version to 1.62.00-6
bnx2x: properly calculate lro_mss
bnx2x: perform statistics "action" before state transition.
bnx2x: properly configure coefficients for MinBW algorithm (NPAR mode).
bnx2x: Fix ethtool -t link test for MF (non-pmf) devices.
bnx2x: Fix nvram test for single port devices.
...
The OpenAFS server is now sending ACKALL packets, so we need to handle them.
Otherwise we report a protocol error and abort.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With slab poisoning enabled, I see the following oops:
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6b73
...
NIP [c0000000006bc61c] .rxrpc_destroy+0x44/0x104
LR [c0000000006bc618] .rxrpc_destroy+0x40/0x104
Call Trace:
[c0000000feb2bc00] [c0000000006bc618] .rxrpc_destroy+0x40/0x104 (unreliable)
[c0000000feb2bc90] [c000000000349b2c] .key_cleanup+0x1a8/0x20c
[c0000000feb2bd40] [c0000000000a2920] .process_one_work+0x2f4/0x4d0
[c0000000feb2be00] [c0000000000a2d50] .worker_thread+0x254/0x468
[c0000000feb2bec0] [c0000000000a868c] .kthread+0xbc/0xc8
[c0000000feb2bf90] [c000000000020e00] .kernel_thread+0x54/0x70
We aren't initialising token->next, but the code in destroy_context relies
on the list being NULL terminated. Use kzalloc to zero out all the fields.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Smith