Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has same vendor and product IDs as G2K devices, but it has
different number of interfaces(4 vs 5) and also different interface
layout where EC20 has QMI on interface 4 instead of 0.
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The lt4112 is a HP branded Huawei me906e modem. Like other Huawei
modems, it does not have a fixed interface to function mapping.
Instead it uses a Huawei specific scheme: functions are mapped by
subclass and protocol.
However, the HP vendor ID is used for modems from many different
manufacturers using different schemes, so we cannot apply a generic
vendor rule like we do for the Huawei vendor ID.
Replace the previous lt4112 entry pointing to an arbitrary interface
number with a device specific subclass + protocol match.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Fixes: bb2bdeb83f ("qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
New device IDs shamelessly lifted from the vendor driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves qmi-wwan to the common parser for CDC user
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other Sierra Wireless MC73xx devices exist, with different USB IDs.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB IDs 0x413c:0x81b1 for the "Dell Wireless 5809e Gobi(TM) 4G
LTE Mobile Broadband Card", a Dell-branded Sierra Wireless EM7305 LTE
card in M.2 form factor, used eg. in Dell's Latitude E7540 Notebook
series.
Signed-off-by: Pieter Hollants <pieter@hollants.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files give these descriptions to the vendor specific
ports on this modem:
VID_19D2&PID_1270&MI_00: "ZTE MF667 Diagnostics Port"
VID_19D2&PID_1270&MI_01: "ZTE MF667 AT Port"
VID_19D2&PID_1270&MI_02: "ZTE MF667 ATExt2 Port"
VID_19D2&PID_1270&MI_03: "ZTE MF667 ATExt Port"
VID_19D2&PID_1270&MI_04: "ZTE MF667 USB Modem"
VID_19D2&PID_1270&MI_05: "ZTE MF667 Network Adapter"
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.
The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware use a new pid and a different interface.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile. This device is tested
and verified to work. The others are assumed to work based on
using the same Windows driver.
Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries. All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.
This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout. This is
corrected.
Reported-by: 王康 <scateu@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Another QMI-speaking device by ZTE, re-branded by ONDA!
I'm connected ovr this device's QMI interface right now, so I can say I tested
it! :)
Note: a follow-up patch was posted to the linux-usb mailing list, to prevent
the option driver from binding to the device's QMI interface, making it
unusable.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A standard Gobi 3000 reference design module.
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC8305 module got an additional entry added based solely on
information from a Windows driver *.inf file. We now have the
actual descriptor layout from one of these modules, and it
consists of two alternate configurations where cfg #1 is a
normal Gobi 2k layout and cfg #2 is MBIM only, using interface
numbers 5 and 6 for MBIM control and data. The extra Windows
driver entry for interface number 5 was most likely a bug.
Deleting the bogus entry to avoid unnecessary qmi_wwan probe
failures when using the MBIM configuration.
Reported-by: Lana Black <sickmind@lavabit.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found in the Windows INF files while investigating the
Novatel/Verizon USB-1000 device. The USB-1000 is verified as
a Gobi1K device and works with QMI after loading appropriate
firmware.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork