![Amit Kumar Salecha](/assets/img/avatar_default.png)
External loopback test can be performed by application without any driver support on normal Ethernet cards. But on CNA devices, where multiple functions share same physical port. Here internal loopback test and external loopback test can be initiated by multiple functions at same time. To co exist all functions, firmware need to regulate what test can be run by which function. So before performing external loopback test, command need to send to firmware, which will quiescent other functions. User may not want to run external loopback test always. As special cable need to be connected for this test. So adding explicit flag in ethtool self test, which will specify interface to perform external loopback test. ETH_TEST_FL_EXTERNAL_LB: Application set to request external loopback test ETH_TEST_FL_EXTERNAL_LB_DONE: Driver ack if test performed Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1201 lines
44 KiB
C
1201 lines
44 KiB
C
/*
|
|
* ethtool.h: Defines for Linux ethtool.
|
|
*
|
|
* Copyright (C) 1998 David S. Miller (davem@redhat.com)
|
|
* Copyright 2001 Jeff Garzik <jgarzik@pobox.com>
|
|
* Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
|
|
* Portions Copyright 2002 Intel (eli.kupermann@intel.com,
|
|
* christopher.leech@intel.com,
|
|
* scott.feldman@intel.com)
|
|
* Portions Copyright (C) Sun Microsystems 2008
|
|
*/
|
|
|
|
#ifndef _LINUX_ETHTOOL_H
|
|
#define _LINUX_ETHTOOL_H
|
|
|
|
#ifdef __KERNEL__
|
|
#include <linux/compat.h>
|
|
#endif
|
|
#include <linux/types.h>
|
|
#include <linux/if_ether.h>
|
|
|
|
/* This should work for both 32 and 64 bit userland. */
|
|
struct ethtool_cmd {
|
|
__u32 cmd;
|
|
__u32 supported; /* Features this interface supports */
|
|
__u32 advertising; /* Features this interface advertises */
|
|
__u16 speed; /* The forced speed (lower bits) in
|
|
* Mbps. Please use
|
|
* ethtool_cmd_speed()/_set() to
|
|
* access it */
|
|
__u8 duplex; /* Duplex, half or full */
|
|
__u8 port; /* Which connector port */
|
|
__u8 phy_address;
|
|
__u8 transceiver; /* Which transceiver to use */
|
|
__u8 autoneg; /* Enable or disable autonegotiation */
|
|
__u8 mdio_support;
|
|
__u32 maxtxpkt; /* Tx pkts before generating tx int */
|
|
__u32 maxrxpkt; /* Rx pkts before generating rx int */
|
|
__u16 speed_hi; /* The forced speed (upper
|
|
* bits) in Mbps. Please use
|
|
* ethtool_cmd_speed()/_set() to
|
|
* access it */
|
|
__u8 eth_tp_mdix;
|
|
__u8 reserved2;
|
|
__u32 lp_advertising; /* Features the link partner advertises */
|
|
__u32 reserved[2];
|
|
};
|
|
|
|
static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
|
|
__u32 speed)
|
|
{
|
|
|
|
ep->speed = (__u16)speed;
|
|
ep->speed_hi = (__u16)(speed >> 16);
|
|
}
|
|
|
|
static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep)
|
|
{
|
|
return (ep->speed_hi << 16) | ep->speed;
|
|
}
|
|
|
|
#define ETHTOOL_FWVERS_LEN 32
|
|
#define ETHTOOL_BUSINFO_LEN 32
|
|
/* these strings are set to whatever the driver author decides... */
|
|
struct ethtool_drvinfo {
|
|
__u32 cmd;
|
|
char driver[32]; /* driver short name, "tulip", "eepro100" */
|
|
char version[32]; /* driver version string */
|
|
char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */
|
|
char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */
|
|
/* For PCI devices, use pci_name(pci_dev). */
|
|
char reserved1[32];
|
|
char reserved2[12];
|
|
/*
|
|
* Some struct members below are filled in
|
|
* using ops->get_sset_count(). Obtaining
|
|
* this info from ethtool_drvinfo is now
|
|
* deprecated; Use ETHTOOL_GSSET_INFO
|
|
* instead.
|
|
*/
|
|
__u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */
|
|
__u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */
|
|
__u32 testinfo_len;
|
|
__u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */
|
|
__u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */
|
|
};
|
|
|
|
#define SOPASS_MAX 6
|
|
/* wake-on-lan settings */
|
|
struct ethtool_wolinfo {
|
|
__u32 cmd;
|
|
__u32 supported;
|
|
__u32 wolopts;
|
|
__u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */
|
|
};
|
|
|
|
/* for passing single values */
|
|
struct ethtool_value {
|
|
__u32 cmd;
|
|
__u32 data;
|
|
};
|
|
|
|
/* for passing big chunks of data */
|
|
struct ethtool_regs {
|
|
__u32 cmd;
|
|
__u32 version; /* driver-specific, indicates different chips/revs */
|
|
__u32 len; /* bytes */
|
|
__u8 data[0];
|
|
};
|
|
|
|
/* for passing EEPROM chunks */
|
|
struct ethtool_eeprom {
|
|
__u32 cmd;
|
|
__u32 magic;
|
|
__u32 offset; /* in bytes */
|
|
__u32 len; /* in bytes */
|
|
__u8 data[0];
|
|
};
|
|
|
|
/* for configuring coalescing parameters of chip */
|
|
struct ethtool_coalesce {
|
|
__u32 cmd; /* ETHTOOL_{G,S}COALESCE */
|
|
|
|
/* How many usecs to delay an RX interrupt after
|
|
* a packet arrives. If 0, only rx_max_coalesced_frames
|
|
* is used.
|
|
*/
|
|
__u32 rx_coalesce_usecs;
|
|
|
|
/* How many packets to delay an RX interrupt after
|
|
* a packet arrives. If 0, only rx_coalesce_usecs is
|
|
* used. It is illegal to set both usecs and max frames
|
|
* to zero as this would cause RX interrupts to never be
|
|
* generated.
|
|
*/
|
|
__u32 rx_max_coalesced_frames;
|
|
|
|
/* Same as above two parameters, except that these values
|
|
* apply while an IRQ is being serviced by the host. Not
|
|
* all cards support this feature and the values are ignored
|
|
* in that case.
|
|
*/
|
|
__u32 rx_coalesce_usecs_irq;
|
|
__u32 rx_max_coalesced_frames_irq;
|
|
|
|
/* How many usecs to delay a TX interrupt after
|
|
* a packet is sent. If 0, only tx_max_coalesced_frames
|
|
* is used.
|
|
*/
|
|
__u32 tx_coalesce_usecs;
|
|
|
|
/* How many packets to delay a TX interrupt after
|
|
* a packet is sent. If 0, only tx_coalesce_usecs is
|
|
* used. It is illegal to set both usecs and max frames
|
|
* to zero as this would cause TX interrupts to never be
|
|
* generated.
|
|
*/
|
|
__u32 tx_max_coalesced_frames;
|
|
|
|
/* Same as above two parameters, except that these values
|
|
* apply while an IRQ is being serviced by the host. Not
|
|
* all cards support this feature and the values are ignored
|
|
* in that case.
|
|
*/
|
|
__u32 tx_coalesce_usecs_irq;
|
|
__u32 tx_max_coalesced_frames_irq;
|
|
|
|
/* How many usecs to delay in-memory statistics
|
|
* block updates. Some drivers do not have an in-memory
|
|
* statistic block, and in such cases this value is ignored.
|
|
* This value must not be zero.
|
|
*/
|
|
__u32 stats_block_coalesce_usecs;
|
|
|
|
/* Adaptive RX/TX coalescing is an algorithm implemented by
|
|
* some drivers to improve latency under low packet rates and
|
|
* improve throughput under high packet rates. Some drivers
|
|
* only implement one of RX or TX adaptive coalescing. Anything
|
|
* not implemented by the driver causes these values to be
|
|
* silently ignored.
|
|
*/
|
|
__u32 use_adaptive_rx_coalesce;
|
|
__u32 use_adaptive_tx_coalesce;
|
|
|
|
/* When the packet rate (measured in packets per second)
|
|
* is below pkt_rate_low, the {rx,tx}_*_low parameters are
|
|
* used.
|
|
*/
|
|
__u32 pkt_rate_low;
|
|
__u32 rx_coalesce_usecs_low;
|
|
__u32 rx_max_coalesced_frames_low;
|
|
__u32 tx_coalesce_usecs_low;
|
|
__u32 tx_max_coalesced_frames_low;
|
|
|
|
/* When the packet rate is below pkt_rate_high but above
|
|
* pkt_rate_low (both measured in packets per second) the
|
|
* normal {rx,tx}_* coalescing parameters are used.
|
|
*/
|
|
|
|
/* When the packet rate is (measured in packets per second)
|
|
* is above pkt_rate_high, the {rx,tx}_*_high parameters are
|
|
* used.
|
|
*/
|
|
__u32 pkt_rate_high;
|
|
__u32 rx_coalesce_usecs_high;
|
|
__u32 rx_max_coalesced_frames_high;
|
|
__u32 tx_coalesce_usecs_high;
|
|
__u32 tx_max_coalesced_frames_high;
|
|
|
|
/* How often to do adaptive coalescing packet rate sampling,
|
|
* measured in seconds. Must not be zero.
|
|
*/
|
|
__u32 rate_sample_interval;
|
|
};
|
|
|
|
/* for configuring RX/TX ring parameters */
|
|
struct ethtool_ringparam {
|
|
__u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */
|
|
|
|
/* Read only attributes. These indicate the maximum number
|
|
* of pending RX/TX ring entries the driver will allow the
|
|
* user to set.
|
|
*/
|
|
__u32 rx_max_pending;
|
|
__u32 rx_mini_max_pending;
|
|
__u32 rx_jumbo_max_pending;
|
|
__u32 tx_max_pending;
|
|
|
|
/* Values changeable by the user. The valid values are
|
|
* in the range 1 to the "*_max_pending" counterpart above.
|
|
*/
|
|
__u32 rx_pending;
|
|
__u32 rx_mini_pending;
|
|
__u32 rx_jumbo_pending;
|
|
__u32 tx_pending;
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_channels - configuring number of network channel
|
|
* @cmd: ETHTOOL_{G,S}CHANNELS
|
|
* @max_rx: Read only. Maximum number of receive channel the driver support.
|
|
* @max_tx: Read only. Maximum number of transmit channel the driver support.
|
|
* @max_other: Read only. Maximum number of other channel the driver support.
|
|
* @max_combined: Read only. Maximum number of combined channel the driver
|
|
* support. Set of queues RX, TX or other.
|
|
* @rx_count: Valid values are in the range 1 to the max_rx.
|
|
* @tx_count: Valid values are in the range 1 to the max_tx.
|
|
* @other_count: Valid values are in the range 1 to the max_other.
|
|
* @combined_count: Valid values are in the range 1 to the max_combined.
|
|
*
|
|
* This can be used to configure RX, TX and other channels.
|
|
*/
|
|
|
|
struct ethtool_channels {
|
|
__u32 cmd;
|
|
__u32 max_rx;
|
|
__u32 max_tx;
|
|
__u32 max_other;
|
|
__u32 max_combined;
|
|
__u32 rx_count;
|
|
__u32 tx_count;
|
|
__u32 other_count;
|
|
__u32 combined_count;
|
|
};
|
|
|
|
/* for configuring link flow control parameters */
|
|
struct ethtool_pauseparam {
|
|
__u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */
|
|
|
|
/* If the link is being auto-negotiated (via ethtool_cmd.autoneg
|
|
* being true) the user may set 'autoneg' here non-zero to have the
|
|
* pause parameters be auto-negotiated too. In such a case, the
|
|
* {rx,tx}_pause values below determine what capabilities are
|
|
* advertised.
|
|
*
|
|
* If 'autoneg' is zero or the link is not being auto-negotiated,
|
|
* then {rx,tx}_pause force the driver to use/not-use pause
|
|
* flow control.
|
|
*/
|
|
__u32 autoneg;
|
|
__u32 rx_pause;
|
|
__u32 tx_pause;
|
|
};
|
|
|
|
#define ETH_GSTRING_LEN 32
|
|
enum ethtool_stringset {
|
|
ETH_SS_TEST = 0,
|
|
ETH_SS_STATS,
|
|
ETH_SS_PRIV_FLAGS,
|
|
ETH_SS_NTUPLE_FILTERS, /* Do not use, GRXNTUPLE is now deprecated */
|
|
ETH_SS_FEATURES,
|
|
};
|
|
|
|
/* for passing string sets for data tagging */
|
|
struct ethtool_gstrings {
|
|
__u32 cmd; /* ETHTOOL_GSTRINGS */
|
|
__u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/
|
|
__u32 len; /* number of strings in the string set */
|
|
__u8 data[0];
|
|
};
|
|
|
|
struct ethtool_sset_info {
|
|
__u32 cmd; /* ETHTOOL_GSSET_INFO */
|
|
__u32 reserved;
|
|
__u64 sset_mask; /* input: each bit selects an sset to query */
|
|
/* output: each bit a returned sset */
|
|
__u32 data[0]; /* ETH_SS_xxx count, in order, based on bits
|
|
in sset_mask. One bit implies one
|
|
__u32, two bits implies two
|
|
__u32's, etc. */
|
|
};
|
|
|
|
/**
|
|
* enum ethtool_test_flags - flags definition of ethtool_test
|
|
* @ETH_TEST_FL_OFFLINE: if set perform online and offline tests, otherwise
|
|
* only online tests.
|
|
* @ETH_TEST_FL_FAILED: Driver set this flag if test fails.
|
|
* @ETH_TEST_FL_EXTERNAL_LB: Application request to perform external loopback
|
|
* test.
|
|
* @ETH_TEST_FL_EXTERNAL_LB_DONE: Driver performed the external loopback test
|
|
*/
|
|
|
|
enum ethtool_test_flags {
|
|
ETH_TEST_FL_OFFLINE = (1 << 0),
|
|
ETH_TEST_FL_FAILED = (1 << 1),
|
|
ETH_TEST_FL_EXTERNAL_LB = (1 << 2),
|
|
ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3),
|
|
};
|
|
|
|
/* for requesting NIC test and getting results*/
|
|
struct ethtool_test {
|
|
__u32 cmd; /* ETHTOOL_TEST */
|
|
__u32 flags; /* ETH_TEST_FL_xxx */
|
|
__u32 reserved;
|
|
__u32 len; /* result length, in number of u64 elements */
|
|
__u64 data[0];
|
|
};
|
|
|
|
/* for dumping NIC-specific statistics */
|
|
struct ethtool_stats {
|
|
__u32 cmd; /* ETHTOOL_GSTATS */
|
|
__u32 n_stats; /* number of u64's being returned */
|
|
__u64 data[0];
|
|
};
|
|
|
|
struct ethtool_perm_addr {
|
|
__u32 cmd; /* ETHTOOL_GPERMADDR */
|
|
__u32 size;
|
|
__u8 data[0];
|
|
};
|
|
|
|
/* boolean flags controlling per-interface behavior characteristics.
|
|
* When reading, the flag indicates whether or not a certain behavior
|
|
* is enabled/present. When writing, the flag indicates whether
|
|
* or not the driver should turn on (set) or off (clear) a behavior.
|
|
*
|
|
* Some behaviors may read-only (unconditionally absent or present).
|
|
* If such is the case, return EINVAL in the set-flags operation if the
|
|
* flag differs from the read-only value.
|
|
*/
|
|
enum ethtool_flags {
|
|
ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */
|
|
ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */
|
|
ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */
|
|
ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */
|
|
ETH_FLAG_RXHASH = (1 << 28),
|
|
};
|
|
|
|
/* The following structures are for supporting RX network flow
|
|
* classification and RX n-tuple configuration. Note, all multibyte
|
|
* fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to
|
|
* be in network byte order.
|
|
*/
|
|
|
|
/**
|
|
* struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc.
|
|
* @ip4src: Source host
|
|
* @ip4dst: Destination host
|
|
* @psrc: Source port
|
|
* @pdst: Destination port
|
|
* @tos: Type-of-service
|
|
*
|
|
* This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow.
|
|
*/
|
|
struct ethtool_tcpip4_spec {
|
|
__be32 ip4src;
|
|
__be32 ip4dst;
|
|
__be16 psrc;
|
|
__be16 pdst;
|
|
__u8 tos;
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4
|
|
* @ip4src: Source host
|
|
* @ip4dst: Destination host
|
|
* @spi: Security parameters index
|
|
* @tos: Type-of-service
|
|
*
|
|
* This can be used to specify an IPsec transport or tunnel over IPv4.
|
|
*/
|
|
struct ethtool_ah_espip4_spec {
|
|
__be32 ip4src;
|
|
__be32 ip4dst;
|
|
__be32 spi;
|
|
__u8 tos;
|
|
};
|
|
|
|
#define ETH_RX_NFC_IP4 1
|
|
|
|
/**
|
|
* struct ethtool_usrip4_spec - general flow specification for IPv4
|
|
* @ip4src: Source host
|
|
* @ip4dst: Destination host
|
|
* @l4_4_bytes: First 4 bytes of transport (layer 4) header
|
|
* @tos: Type-of-service
|
|
* @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0
|
|
* @proto: Transport protocol number; mask must be 0
|
|
*/
|
|
struct ethtool_usrip4_spec {
|
|
__be32 ip4src;
|
|
__be32 ip4dst;
|
|
__be32 l4_4_bytes;
|
|
__u8 tos;
|
|
__u8 ip_ver;
|
|
__u8 proto;
|
|
};
|
|
|
|
union ethtool_flow_union {
|
|
struct ethtool_tcpip4_spec tcp_ip4_spec;
|
|
struct ethtool_tcpip4_spec udp_ip4_spec;
|
|
struct ethtool_tcpip4_spec sctp_ip4_spec;
|
|
struct ethtool_ah_espip4_spec ah_ip4_spec;
|
|
struct ethtool_ah_espip4_spec esp_ip4_spec;
|
|
struct ethtool_usrip4_spec usr_ip4_spec;
|
|
struct ethhdr ether_spec;
|
|
__u8 hdata[60];
|
|
};
|
|
|
|
struct ethtool_flow_ext {
|
|
__be16 vlan_etype;
|
|
__be16 vlan_tci;
|
|
__be32 data[2];
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_rx_flow_spec - specification for RX flow filter
|
|
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
|
|
* @h_u: Flow fields to match (dependent on @flow_type)
|
|
* @h_ext: Additional fields to match
|
|
* @m_u: Masks for flow field bits to be matched
|
|
* @m_ext: Masks for additional field bits to be matched
|
|
* Note, all additional fields must be ignored unless @flow_type
|
|
* includes the %FLOW_EXT flag.
|
|
* @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC
|
|
* if packets should be discarded
|
|
* @location: Index of filter in hardware table
|
|
*/
|
|
struct ethtool_rx_flow_spec {
|
|
__u32 flow_type;
|
|
union ethtool_flow_union h_u;
|
|
struct ethtool_flow_ext h_ext;
|
|
union ethtool_flow_union m_u;
|
|
struct ethtool_flow_ext m_ext;
|
|
__u64 ring_cookie;
|
|
__u32 location;
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_rxnfc - command to get or set RX flow classification rules
|
|
* @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH,
|
|
* %ETHTOOL_GRXRINGS, %ETHTOOL_GRXCLSRLCNT, %ETHTOOL_GRXCLSRULE,
|
|
* %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS
|
|
* @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW
|
|
* @data: Command-dependent value
|
|
* @fs: Flow filter specification
|
|
* @rule_cnt: Number of rules to be affected
|
|
* @rule_locs: Array of valid rule indices
|
|
*
|
|
* For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating
|
|
* the fields included in the flow hash, e.g. %RXH_IP_SRC. The following
|
|
* structure fields must not be used.
|
|
*
|
|
* For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues
|
|
* on return.
|
|
*
|
|
* For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined
|
|
* rules on return.
|
|
*
|
|
* For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the index of an
|
|
* existing filter rule on entry and @fs contains the rule on return.
|
|
*
|
|
* For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the
|
|
* user buffer for @rule_locs on entry. On return, @data is the size
|
|
* of the filter table and @rule_locs contains the indices of the
|
|
* defined rules.
|
|
*
|
|
* For %ETHTOOL_SRXCLSRLINS, @fs specifies the filter rule to add or
|
|
* update. @fs.@location specifies the index to use and must not be
|
|
* ignored.
|
|
*
|
|
* For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the index of an
|
|
* existing filter rule on entry.
|
|
*
|
|
* Implementation of indexed classification rules generally requires a
|
|
* TCAM.
|
|
*/
|
|
struct ethtool_rxnfc {
|
|
__u32 cmd;
|
|
__u32 flow_type;
|
|
__u64 data;
|
|
struct ethtool_rx_flow_spec fs;
|
|
__u32 rule_cnt;
|
|
__u32 rule_locs[0];
|
|
};
|
|
|
|
#ifdef __KERNEL__
|
|
#ifdef CONFIG_COMPAT
|
|
|
|
struct compat_ethtool_rx_flow_spec {
|
|
u32 flow_type;
|
|
union ethtool_flow_union h_u;
|
|
struct ethtool_flow_ext h_ext;
|
|
union ethtool_flow_union m_u;
|
|
struct ethtool_flow_ext m_ext;
|
|
compat_u64 ring_cookie;
|
|
u32 location;
|
|
};
|
|
|
|
struct compat_ethtool_rxnfc {
|
|
u32 cmd;
|
|
u32 flow_type;
|
|
compat_u64 data;
|
|
struct compat_ethtool_rx_flow_spec fs;
|
|
u32 rule_cnt;
|
|
u32 rule_locs[0];
|
|
};
|
|
|
|
#endif /* CONFIG_COMPAT */
|
|
#endif /* __KERNEL__ */
|
|
|
|
/**
|
|
* struct ethtool_rxfh_indir - command to get or set RX flow hash indirection
|
|
* @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR
|
|
* @size: On entry, the array size of the user buffer. On return from
|
|
* %ETHTOOL_GRXFHINDIR, the array size of the hardware indirection table.
|
|
* @ring_index: RX ring/queue index for each hash value
|
|
*/
|
|
struct ethtool_rxfh_indir {
|
|
__u32 cmd;
|
|
__u32 size;
|
|
__u32 ring_index[0];
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter
|
|
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
|
|
* @h_u: Flow field values to match (dependent on @flow_type)
|
|
* @m_u: Masks for flow field value bits to be ignored
|
|
* @vlan_tag: VLAN tag to match
|
|
* @vlan_tag_mask: Mask for VLAN tag bits to be ignored
|
|
* @data: Driver-dependent data to match
|
|
* @data_mask: Mask for driver-dependent data bits to be ignored
|
|
* @action: RX ring/queue index to deliver to (non-negative) or other action
|
|
* (negative, e.g. %ETHTOOL_RXNTUPLE_ACTION_DROP)
|
|
*
|
|
* For flow types %TCP_V4_FLOW, %UDP_V4_FLOW and %SCTP_V4_FLOW, where
|
|
* a field value and mask are both zero this is treated as if all mask
|
|
* bits are set i.e. the field is ignored.
|
|
*/
|
|
struct ethtool_rx_ntuple_flow_spec {
|
|
__u32 flow_type;
|
|
union {
|
|
struct ethtool_tcpip4_spec tcp_ip4_spec;
|
|
struct ethtool_tcpip4_spec udp_ip4_spec;
|
|
struct ethtool_tcpip4_spec sctp_ip4_spec;
|
|
struct ethtool_ah_espip4_spec ah_ip4_spec;
|
|
struct ethtool_ah_espip4_spec esp_ip4_spec;
|
|
struct ethtool_usrip4_spec usr_ip4_spec;
|
|
struct ethhdr ether_spec;
|
|
__u8 hdata[72];
|
|
} h_u, m_u;
|
|
|
|
__u16 vlan_tag;
|
|
__u16 vlan_tag_mask;
|
|
__u64 data;
|
|
__u64 data_mask;
|
|
|
|
__s32 action;
|
|
#define ETHTOOL_RXNTUPLE_ACTION_DROP (-1) /* drop packet */
|
|
#define ETHTOOL_RXNTUPLE_ACTION_CLEAR (-2) /* clear filter */
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_rx_ntuple - command to set or clear RX flow filter
|
|
* @cmd: Command number - %ETHTOOL_SRXNTUPLE
|
|
* @fs: Flow filter specification
|
|
*/
|
|
struct ethtool_rx_ntuple {
|
|
__u32 cmd;
|
|
struct ethtool_rx_ntuple_flow_spec fs;
|
|
};
|
|
|
|
#define ETHTOOL_FLASH_MAX_FILENAME 128
|
|
enum ethtool_flash_op_type {
|
|
ETHTOOL_FLASH_ALL_REGIONS = 0,
|
|
};
|
|
|
|
/* for passing firmware flashing related parameters */
|
|
struct ethtool_flash {
|
|
__u32 cmd;
|
|
__u32 region;
|
|
char data[ETHTOOL_FLASH_MAX_FILENAME];
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_dump - used for retrieving, setting device dump
|
|
* @cmd: Command number - %ETHTOOL_GET_DUMP_FLAG, %ETHTOOL_GET_DUMP_DATA, or
|
|
* %ETHTOOL_SET_DUMP
|
|
* @version: FW version of the dump, filled in by driver
|
|
* @flag: driver dependent flag for dump setting, filled in by driver during
|
|
* get and filled in by ethtool for set operation
|
|
* @len: length of dump data, used as the length of the user buffer on entry to
|
|
* %ETHTOOL_GET_DUMP_DATA and this is returned as dump length by driver
|
|
* for %ETHTOOL_GET_DUMP_FLAG command
|
|
* @data: data collected for get dump data operation
|
|
*/
|
|
struct ethtool_dump {
|
|
__u32 cmd;
|
|
__u32 version;
|
|
__u32 flag;
|
|
__u32 len;
|
|
__u8 data[0];
|
|
};
|
|
|
|
/* for returning and changing feature sets */
|
|
|
|
/**
|
|
* struct ethtool_get_features_block - block with state of 32 features
|
|
* @available: mask of changeable features
|
|
* @requested: mask of features requested to be enabled if possible
|
|
* @active: mask of currently enabled features
|
|
* @never_changed: mask of features not changeable for any device
|
|
*/
|
|
struct ethtool_get_features_block {
|
|
__u32 available;
|
|
__u32 requested;
|
|
__u32 active;
|
|
__u32 never_changed;
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_gfeatures - command to get state of device's features
|
|
* @cmd: command number = %ETHTOOL_GFEATURES
|
|
* @size: in: number of elements in the features[] array;
|
|
* out: number of elements in features[] needed to hold all features
|
|
* @features: state of features
|
|
*/
|
|
struct ethtool_gfeatures {
|
|
__u32 cmd;
|
|
__u32 size;
|
|
struct ethtool_get_features_block features[0];
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_set_features_block - block with request for 32 features
|
|
* @valid: mask of features to be changed
|
|
* @requested: values of features to be changed
|
|
*/
|
|
struct ethtool_set_features_block {
|
|
__u32 valid;
|
|
__u32 requested;
|
|
};
|
|
|
|
/**
|
|
* struct ethtool_sfeatures - command to request change in device's features
|
|
* @cmd: command number = %ETHTOOL_SFEATURES
|
|
* @size: array size of the features[] array
|
|
* @features: feature change masks
|
|
*/
|
|
struct ethtool_sfeatures {
|
|
__u32 cmd;
|
|
__u32 size;
|
|
struct ethtool_set_features_block features[0];
|
|
};
|
|
|
|
/*
|
|
* %ETHTOOL_SFEATURES changes features present in features[].valid to the
|
|
* values of corresponding bits in features[].requested. Bits in .requested
|
|
* not set in .valid or not changeable are ignored.
|
|
*
|
|
* Returns %EINVAL when .valid contains undefined or never-changeable bits
|
|
* or size is not equal to required number of features words (32-bit blocks).
|
|
* Returns >= 0 if request was completed; bits set in the value mean:
|
|
* %ETHTOOL_F_UNSUPPORTED - there were bits set in .valid that are not
|
|
* changeable (not present in %ETHTOOL_GFEATURES' features[].available)
|
|
* those bits were ignored.
|
|
* %ETHTOOL_F_WISH - some or all changes requested were recorded but the
|
|
* resulting state of bits masked by .valid is not equal to .requested.
|
|
* Probably there are other device-specific constraints on some features
|
|
* in the set. When %ETHTOOL_F_UNSUPPORTED is set, .valid is considered
|
|
* here as though ignored bits were cleared.
|
|
* %ETHTOOL_F_COMPAT - some or all changes requested were made by calling
|
|
* compatibility functions. Requested offload state cannot be properly
|
|
* managed by kernel.
|
|
*
|
|
* Meaning of bits in the masks are obtained by %ETHTOOL_GSSET_INFO (number of
|
|
* bits in the arrays - always multiple of 32) and %ETHTOOL_GSTRINGS commands
|
|
* for ETH_SS_FEATURES string set. First entry in the table corresponds to least
|
|
* significant bit in features[0] fields. Empty strings mark undefined features.
|
|
*/
|
|
enum ethtool_sfeatures_retval_bits {
|
|
ETHTOOL_F_UNSUPPORTED__BIT,
|
|
ETHTOOL_F_WISH__BIT,
|
|
ETHTOOL_F_COMPAT__BIT,
|
|
};
|
|
|
|
#define ETHTOOL_F_UNSUPPORTED (1 << ETHTOOL_F_UNSUPPORTED__BIT)
|
|
#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT)
|
|
#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT)
|
|
|
|
#ifdef __KERNEL__
|
|
|
|
#include <linux/rculist.h>
|
|
|
|
/* needed by dev_disable_lro() */
|
|
extern int __ethtool_set_flags(struct net_device *dev, u32 flags);
|
|
|
|
/**
|
|
* enum ethtool_phys_id_state - indicator state for physical identification
|
|
* @ETHTOOL_ID_INACTIVE: Physical ID indicator should be deactivated
|
|
* @ETHTOOL_ID_ACTIVE: Physical ID indicator should be activated
|
|
* @ETHTOOL_ID_ON: LED should be turned on (used iff %ETHTOOL_ID_ACTIVE
|
|
* is not supported)
|
|
* @ETHTOOL_ID_OFF: LED should be turned off (used iff %ETHTOOL_ID_ACTIVE
|
|
* is not supported)
|
|
*/
|
|
enum ethtool_phys_id_state {
|
|
ETHTOOL_ID_INACTIVE,
|
|
ETHTOOL_ID_ACTIVE,
|
|
ETHTOOL_ID_ON,
|
|
ETHTOOL_ID_OFF
|
|
};
|
|
|
|
struct net_device;
|
|
|
|
/* Some generic methods drivers may use in their ethtool_ops */
|
|
u32 ethtool_op_get_link(struct net_device *dev);
|
|
u32 ethtool_op_get_tx_csum(struct net_device *dev);
|
|
int ethtool_op_set_tx_csum(struct net_device *dev, u32 data);
|
|
int ethtool_op_set_tx_hw_csum(struct net_device *dev, u32 data);
|
|
int ethtool_op_set_tx_ipv6_csum(struct net_device *dev, u32 data);
|
|
u32 ethtool_op_get_sg(struct net_device *dev);
|
|
int ethtool_op_set_sg(struct net_device *dev, u32 data);
|
|
u32 ethtool_op_get_tso(struct net_device *dev);
|
|
int ethtool_op_set_tso(struct net_device *dev, u32 data);
|
|
u32 ethtool_op_get_ufo(struct net_device *dev);
|
|
int ethtool_op_set_ufo(struct net_device *dev, u32 data);
|
|
u32 ethtool_op_get_flags(struct net_device *dev);
|
|
int ethtool_op_set_flags(struct net_device *dev, u32 data, u32 supported);
|
|
bool ethtool_invalid_flags(struct net_device *dev, u32 data, u32 supported);
|
|
|
|
/**
|
|
* struct ethtool_ops - optional netdev operations
|
|
* @get_settings: Get various device settings including Ethernet link
|
|
* settings. The @cmd parameter is expected to have been cleared
|
|
* before get_settings is called. Returns a negative error code or
|
|
* zero.
|
|
* @set_settings: Set various device settings including Ethernet link
|
|
* settings. Returns a negative error code or zero.
|
|
* @get_drvinfo: Report driver/device information. Should only set the
|
|
* @driver, @version, @fw_version and @bus_info fields. If not
|
|
* implemented, the @driver and @bus_info fields will be filled in
|
|
* according to the netdev's parent device.
|
|
* @get_regs_len: Get buffer length required for @get_regs
|
|
* @get_regs: Get device registers
|
|
* @get_wol: Report whether Wake-on-Lan is enabled
|
|
* @set_wol: Turn Wake-on-Lan on or off. Returns a negative error code
|
|
* or zero.
|
|
* @get_msglevel: Report driver message level. This should be the value
|
|
* of the @msg_enable field used by netif logging functions.
|
|
* @set_msglevel: Set driver message level
|
|
* @nway_reset: Restart autonegotiation. Returns a negative error code
|
|
* or zero.
|
|
* @get_link: Report whether physical link is up. Will only be called if
|
|
* the netdev is up. Should usually be set to ethtool_op_get_link(),
|
|
* which uses netif_carrier_ok().
|
|
* @get_eeprom: Read data from the device EEPROM.
|
|
* Should fill in the magic field. Don't need to check len for zero
|
|
* or wraparound. Fill in the data argument with the eeprom values
|
|
* from offset to offset + len. Update len to the amount read.
|
|
* Returns an error or zero.
|
|
* @set_eeprom: Write data to the device EEPROM.
|
|
* Should validate the magic field. Don't need to check len for zero
|
|
* or wraparound. Update len to the amount written. Returns an error
|
|
* or zero.
|
|
* @get_coalesce: Get interrupt coalescing parameters. Returns a negative
|
|
* error code or zero.
|
|
* @set_coalesce: Set interrupt coalescing parameters. Returns a negative
|
|
* error code or zero.
|
|
* @get_ringparam: Report ring sizes
|
|
* @set_ringparam: Set ring sizes. Returns a negative error code or zero.
|
|
* @get_pauseparam: Report pause parameters
|
|
* @set_pauseparam: Set pause parameters. Returns a negative error code
|
|
* or zero.
|
|
* @get_rx_csum: Deprecated in favour of the netdev feature %NETIF_F_RXCSUM.
|
|
* Report whether receive checksums are turned on or off.
|
|
* @set_rx_csum: Deprecated in favour of generic netdev features. Turn
|
|
* receive checksum on or off. Returns a negative error code or zero.
|
|
* @get_tx_csum: Deprecated as redundant. Report whether transmit checksums
|
|
* are turned on or off.
|
|
* @set_tx_csum: Deprecated in favour of generic netdev features. Turn
|
|
* transmit checksums on or off. Returns a negative error code or zero.
|
|
* @get_sg: Deprecated as redundant. Report whether scatter-gather is
|
|
* enabled.
|
|
* @set_sg: Deprecated in favour of generic netdev features. Turn
|
|
* scatter-gather on or off. Returns a negative error code or zero.
|
|
* @get_tso: Deprecated as redundant. Report whether TCP segmentation
|
|
* offload is enabled.
|
|
* @set_tso: Deprecated in favour of generic netdev features. Turn TCP
|
|
* segmentation offload on or off. Returns a negative error code or zero.
|
|
* @self_test: Run specified self-tests
|
|
* @get_strings: Return a set of strings that describe the requested objects
|
|
* @set_phys_id: Identify the physical devices, e.g. by flashing an LED
|
|
* attached to it. The implementation may update the indicator
|
|
* asynchronously or synchronously, but in either case it must return
|
|
* quickly. It is initially called with the argument %ETHTOOL_ID_ACTIVE,
|
|
* and must either activate asynchronous updates and return zero, return
|
|
* a negative error or return a positive frequency for synchronous
|
|
* indication (e.g. 1 for one on/off cycle per second). If it returns
|
|
* a frequency then it will be called again at intervals with the
|
|
* argument %ETHTOOL_ID_ON or %ETHTOOL_ID_OFF and should set the state of
|
|
* the indicator accordingly. Finally, it is called with the argument
|
|
* %ETHTOOL_ID_INACTIVE and must deactivate the indicator. Returns a
|
|
* negative error code or zero.
|
|
* @get_ethtool_stats: Return extended statistics about the device.
|
|
* This is only useful if the device maintains statistics not
|
|
* included in &struct rtnl_link_stats64.
|
|
* @begin: Function to be called before any other operation. Returns a
|
|
* negative error code or zero.
|
|
* @complete: Function to be called after any other operation except
|
|
* @begin. Will be called even if the other operation failed.
|
|
* @get_ufo: Deprecated as redundant. Report whether UDP fragmentation
|
|
* offload is enabled.
|
|
* @set_ufo: Deprecated in favour of generic netdev features. Turn UDP
|
|
* fragmentation offload on or off. Returns a negative error code or zero.
|
|
* @get_flags: Deprecated as redundant. Report features included in
|
|
* &enum ethtool_flags that are enabled.
|
|
* @set_flags: Deprecated in favour of generic netdev features. Turn
|
|
* features included in &enum ethtool_flags on or off. Returns a
|
|
* negative error code or zero.
|
|
* @get_priv_flags: Report driver-specific feature flags.
|
|
* @set_priv_flags: Set driver-specific feature flags. Returns a negative
|
|
* error code or zero.
|
|
* @get_sset_count: Get number of strings that @get_strings will write.
|
|
* @get_rxnfc: Get RX flow classification rules. Returns a negative
|
|
* error code or zero.
|
|
* @set_rxnfc: Set RX flow classification rules. Returns a negative
|
|
* error code or zero.
|
|
* @flash_device: Write a firmware image to device's flash memory.
|
|
* Returns a negative error code or zero.
|
|
* @reset: Reset (part of) the device, as specified by a bitmask of
|
|
* flags from &enum ethtool_reset_flags. Returns a negative
|
|
* error code or zero.
|
|
* @set_rx_ntuple: Set an RX n-tuple rule. Returns a negative error code
|
|
* or zero.
|
|
* @get_rxfh_indir: Get the contents of the RX flow hash indirection table.
|
|
* Returns a negative error code or zero.
|
|
* @set_rxfh_indir: Set the contents of the RX flow hash indirection table.
|
|
* Returns a negative error code or zero.
|
|
* @get_channels: Get number of channels.
|
|
* @set_channels: Set number of channels. Returns a negative error code or
|
|
* zero.
|
|
* @get_dump_flag: Get dump flag indicating current dump length, version,
|
|
* and flag of the device.
|
|
* @get_dump_data: Get dump data.
|
|
* @set_dump: Set dump specific flags to the device.
|
|
*
|
|
* All operations are optional (i.e. the function pointer may be set
|
|
* to %NULL) and callers must take this into account. Callers must
|
|
* hold the RTNL, except that for @get_drvinfo the caller may or may
|
|
* not hold the RTNL.
|
|
*
|
|
* See the structures used by these operations for further documentation.
|
|
*
|
|
* See &struct net_device and &struct net_device_ops for documentation
|
|
* of the generic netdev features interface.
|
|
*/
|
|
struct ethtool_ops {
|
|
int (*get_settings)(struct net_device *, struct ethtool_cmd *);
|
|
int (*set_settings)(struct net_device *, struct ethtool_cmd *);
|
|
void (*get_drvinfo)(struct net_device *, struct ethtool_drvinfo *);
|
|
int (*get_regs_len)(struct net_device *);
|
|
void (*get_regs)(struct net_device *, struct ethtool_regs *, void *);
|
|
void (*get_wol)(struct net_device *, struct ethtool_wolinfo *);
|
|
int (*set_wol)(struct net_device *, struct ethtool_wolinfo *);
|
|
u32 (*get_msglevel)(struct net_device *);
|
|
void (*set_msglevel)(struct net_device *, u32);
|
|
int (*nway_reset)(struct net_device *);
|
|
u32 (*get_link)(struct net_device *);
|
|
int (*get_eeprom_len)(struct net_device *);
|
|
int (*get_eeprom)(struct net_device *,
|
|
struct ethtool_eeprom *, u8 *);
|
|
int (*set_eeprom)(struct net_device *,
|
|
struct ethtool_eeprom *, u8 *);
|
|
int (*get_coalesce)(struct net_device *, struct ethtool_coalesce *);
|
|
int (*set_coalesce)(struct net_device *, struct ethtool_coalesce *);
|
|
void (*get_ringparam)(struct net_device *,
|
|
struct ethtool_ringparam *);
|
|
int (*set_ringparam)(struct net_device *,
|
|
struct ethtool_ringparam *);
|
|
void (*get_pauseparam)(struct net_device *,
|
|
struct ethtool_pauseparam*);
|
|
int (*set_pauseparam)(struct net_device *,
|
|
struct ethtool_pauseparam*);
|
|
u32 (*get_rx_csum)(struct net_device *);
|
|
int (*set_rx_csum)(struct net_device *, u32);
|
|
u32 (*get_tx_csum)(struct net_device *);
|
|
int (*set_tx_csum)(struct net_device *, u32);
|
|
u32 (*get_sg)(struct net_device *);
|
|
int (*set_sg)(struct net_device *, u32);
|
|
u32 (*get_tso)(struct net_device *);
|
|
int (*set_tso)(struct net_device *, u32);
|
|
void (*self_test)(struct net_device *, struct ethtool_test *, u64 *);
|
|
void (*get_strings)(struct net_device *, u32 stringset, u8 *);
|
|
int (*set_phys_id)(struct net_device *, enum ethtool_phys_id_state);
|
|
void (*get_ethtool_stats)(struct net_device *,
|
|
struct ethtool_stats *, u64 *);
|
|
int (*begin)(struct net_device *);
|
|
void (*complete)(struct net_device *);
|
|
u32 (*get_ufo)(struct net_device *);
|
|
int (*set_ufo)(struct net_device *, u32);
|
|
u32 (*get_flags)(struct net_device *);
|
|
int (*set_flags)(struct net_device *, u32);
|
|
u32 (*get_priv_flags)(struct net_device *);
|
|
int (*set_priv_flags)(struct net_device *, u32);
|
|
int (*get_sset_count)(struct net_device *, int);
|
|
int (*get_rxnfc)(struct net_device *,
|
|
struct ethtool_rxnfc *, void *);
|
|
int (*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *);
|
|
int (*flash_device)(struct net_device *, struct ethtool_flash *);
|
|
int (*reset)(struct net_device *, u32 *);
|
|
int (*set_rx_ntuple)(struct net_device *,
|
|
struct ethtool_rx_ntuple *);
|
|
int (*get_rxfh_indir)(struct net_device *,
|
|
struct ethtool_rxfh_indir *);
|
|
int (*set_rxfh_indir)(struct net_device *,
|
|
const struct ethtool_rxfh_indir *);
|
|
void (*get_channels)(struct net_device *, struct ethtool_channels *);
|
|
int (*set_channels)(struct net_device *, struct ethtool_channels *);
|
|
int (*get_dump_flag)(struct net_device *, struct ethtool_dump *);
|
|
int (*get_dump_data)(struct net_device *,
|
|
struct ethtool_dump *, void *);
|
|
int (*set_dump)(struct net_device *, struct ethtool_dump *);
|
|
|
|
};
|
|
#endif /* __KERNEL__ */
|
|
|
|
/* CMDs currently supported */
|
|
#define ETHTOOL_GSET 0x00000001 /* Get settings. */
|
|
#define ETHTOOL_SSET 0x00000002 /* Set settings. */
|
|
#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */
|
|
#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */
|
|
#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */
|
|
#define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */
|
|
#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */
|
|
#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */
|
|
#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */
|
|
/* Get link status for host, i.e. whether the interface *and* the
|
|
* physical port (if there is one) are up (ethtool_value). */
|
|
#define ETHTOOL_GLINK 0x0000000a
|
|
#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */
|
|
#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */
|
|
#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */
|
|
#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */
|
|
#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */
|
|
#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */
|
|
#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */
|
|
#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */
|
|
#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */
|
|
#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */
|
|
#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */
|
|
#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */
|
|
#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable
|
|
* (ethtool_value) */
|
|
#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable
|
|
* (ethtool_value). */
|
|
#define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */
|
|
#define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */
|
|
#define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */
|
|
#define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */
|
|
#define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */
|
|
#define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */
|
|
#define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */
|
|
#define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */
|
|
#define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */
|
|
#define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */
|
|
#define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */
|
|
#define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */
|
|
#define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */
|
|
#define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */
|
|
#define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */
|
|
|
|
#define ETHTOOL_GRXFH 0x00000029 /* Get RX flow hash configuration */
|
|
#define ETHTOOL_SRXFH 0x0000002a /* Set RX flow hash configuration */
|
|
#define ETHTOOL_GGRO 0x0000002b /* Get GRO enable (ethtool_value) */
|
|
#define ETHTOOL_SGRO 0x0000002c /* Set GRO enable (ethtool_value) */
|
|
#define ETHTOOL_GRXRINGS 0x0000002d /* Get RX rings available for LB */
|
|
#define ETHTOOL_GRXCLSRLCNT 0x0000002e /* Get RX class rule count */
|
|
#define ETHTOOL_GRXCLSRULE 0x0000002f /* Get RX classification rule */
|
|
#define ETHTOOL_GRXCLSRLALL 0x00000030 /* Get all RX classification rule */
|
|
#define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */
|
|
#define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */
|
|
#define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */
|
|
#define ETHTOOL_RESET 0x00000034 /* Reset hardware */
|
|
#define ETHTOOL_SRXNTUPLE 0x00000035 /* Add an n-tuple filter to device */
|
|
#define ETHTOOL_GRXNTUPLE 0x00000036 /* deprecated */
|
|
#define ETHTOOL_GSSET_INFO 0x00000037 /* Get string set info */
|
|
#define ETHTOOL_GRXFHINDIR 0x00000038 /* Get RX flow hash indir'n table */
|
|
#define ETHTOOL_SRXFHINDIR 0x00000039 /* Set RX flow hash indir'n table */
|
|
|
|
#define ETHTOOL_GFEATURES 0x0000003a /* Get device offload settings */
|
|
#define ETHTOOL_SFEATURES 0x0000003b /* Change device offload settings */
|
|
#define ETHTOOL_GCHANNELS 0x0000003c /* Get no of channels */
|
|
#define ETHTOOL_SCHANNELS 0x0000003d /* Set no of channels */
|
|
#define ETHTOOL_SET_DUMP 0x0000003e /* Set dump settings */
|
|
#define ETHTOOL_GET_DUMP_FLAG 0x0000003f /* Get dump settings */
|
|
#define ETHTOOL_GET_DUMP_DATA 0x00000040 /* Get dump data */
|
|
|
|
/* compatibility with older code */
|
|
#define SPARC_ETH_GSET ETHTOOL_GSET
|
|
#define SPARC_ETH_SSET ETHTOOL_SSET
|
|
|
|
/* Indicates what features are supported by the interface. */
|
|
#define SUPPORTED_10baseT_Half (1 << 0)
|
|
#define SUPPORTED_10baseT_Full (1 << 1)
|
|
#define SUPPORTED_100baseT_Half (1 << 2)
|
|
#define SUPPORTED_100baseT_Full (1 << 3)
|
|
#define SUPPORTED_1000baseT_Half (1 << 4)
|
|
#define SUPPORTED_1000baseT_Full (1 << 5)
|
|
#define SUPPORTED_Autoneg (1 << 6)
|
|
#define SUPPORTED_TP (1 << 7)
|
|
#define SUPPORTED_AUI (1 << 8)
|
|
#define SUPPORTED_MII (1 << 9)
|
|
#define SUPPORTED_FIBRE (1 << 10)
|
|
#define SUPPORTED_BNC (1 << 11)
|
|
#define SUPPORTED_10000baseT_Full (1 << 12)
|
|
#define SUPPORTED_Pause (1 << 13)
|
|
#define SUPPORTED_Asym_Pause (1 << 14)
|
|
#define SUPPORTED_2500baseX_Full (1 << 15)
|
|
#define SUPPORTED_Backplane (1 << 16)
|
|
#define SUPPORTED_1000baseKX_Full (1 << 17)
|
|
#define SUPPORTED_10000baseKX4_Full (1 << 18)
|
|
#define SUPPORTED_10000baseKR_Full (1 << 19)
|
|
#define SUPPORTED_10000baseR_FEC (1 << 20)
|
|
#define SUPPORTED_20000baseMLD2_Full (1 << 21)
|
|
#define SUPPORTED_20000baseKR2_Full (1 << 22)
|
|
|
|
/* Indicates what features are advertised by the interface. */
|
|
#define ADVERTISED_10baseT_Half (1 << 0)
|
|
#define ADVERTISED_10baseT_Full (1 << 1)
|
|
#define ADVERTISED_100baseT_Half (1 << 2)
|
|
#define ADVERTISED_100baseT_Full (1 << 3)
|
|
#define ADVERTISED_1000baseT_Half (1 << 4)
|
|
#define ADVERTISED_1000baseT_Full (1 << 5)
|
|
#define ADVERTISED_Autoneg (1 << 6)
|
|
#define ADVERTISED_TP (1 << 7)
|
|
#define ADVERTISED_AUI (1 << 8)
|
|
#define ADVERTISED_MII (1 << 9)
|
|
#define ADVERTISED_FIBRE (1 << 10)
|
|
#define ADVERTISED_BNC (1 << 11)
|
|
#define ADVERTISED_10000baseT_Full (1 << 12)
|
|
#define ADVERTISED_Pause (1 << 13)
|
|
#define ADVERTISED_Asym_Pause (1 << 14)
|
|
#define ADVERTISED_2500baseX_Full (1 << 15)
|
|
#define ADVERTISED_Backplane (1 << 16)
|
|
#define ADVERTISED_1000baseKX_Full (1 << 17)
|
|
#define ADVERTISED_10000baseKX4_Full (1 << 18)
|
|
#define ADVERTISED_10000baseKR_Full (1 << 19)
|
|
#define ADVERTISED_10000baseR_FEC (1 << 20)
|
|
#define ADVERTISED_20000baseMLD2_Full (1 << 21)
|
|
#define ADVERTISED_20000baseKR2_Full (1 << 22)
|
|
|
|
/* The following are all involved in forcing a particular link
|
|
* mode for the device for setting things. When getting the
|
|
* devices settings, these indicate the current mode and whether
|
|
* it was forced up into this mode or autonegotiated.
|
|
*/
|
|
|
|
/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
|
|
#define SPEED_10 10
|
|
#define SPEED_100 100
|
|
#define SPEED_1000 1000
|
|
#define SPEED_2500 2500
|
|
#define SPEED_10000 10000
|
|
|
|
/* Duplex, half or full. */
|
|
#define DUPLEX_HALF 0x00
|
|
#define DUPLEX_FULL 0x01
|
|
|
|
/* Which connector port. */
|
|
#define PORT_TP 0x00
|
|
#define PORT_AUI 0x01
|
|
#define PORT_MII 0x02
|
|
#define PORT_FIBRE 0x03
|
|
#define PORT_BNC 0x04
|
|
#define PORT_DA 0x05
|
|
#define PORT_NONE 0xef
|
|
#define PORT_OTHER 0xff
|
|
|
|
/* Which transceiver to use. */
|
|
#define XCVR_INTERNAL 0x00
|
|
#define XCVR_EXTERNAL 0x01
|
|
#define XCVR_DUMMY1 0x02
|
|
#define XCVR_DUMMY2 0x03
|
|
#define XCVR_DUMMY3 0x04
|
|
|
|
/* Enable or disable autonegotiation. If this is set to enable,
|
|
* the forced link modes above are completely ignored.
|
|
*/
|
|
#define AUTONEG_DISABLE 0x00
|
|
#define AUTONEG_ENABLE 0x01
|
|
|
|
/* Mode MDI or MDI-X */
|
|
#define ETH_TP_MDI_INVALID 0x00
|
|
#define ETH_TP_MDI 0x01
|
|
#define ETH_TP_MDI_X 0x02
|
|
|
|
/* Wake-On-Lan options. */
|
|
#define WAKE_PHY (1 << 0)
|
|
#define WAKE_UCAST (1 << 1)
|
|
#define WAKE_MCAST (1 << 2)
|
|
#define WAKE_BCAST (1 << 3)
|
|
#define WAKE_ARP (1 << 4)
|
|
#define WAKE_MAGIC (1 << 5)
|
|
#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */
|
|
|
|
/* L2-L4 network traffic flow types */
|
|
#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */
|
|
#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
|
|
#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
|
|
#define AH_ESP_V4_FLOW 0x04 /* hash only */
|
|
#define TCP_V6_FLOW 0x05 /* hash only */
|
|
#define UDP_V6_FLOW 0x06 /* hash only */
|
|
#define SCTP_V6_FLOW 0x07 /* hash only */
|
|
#define AH_ESP_V6_FLOW 0x08 /* hash only */
|
|
#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
|
|
#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
|
|
#define AH_V6_FLOW 0x0b /* hash only */
|
|
#define ESP_V6_FLOW 0x0c /* hash only */
|
|
#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
|
|
#define IPV4_FLOW 0x10 /* hash only */
|
|
#define IPV6_FLOW 0x11 /* hash only */
|
|
#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
|
|
/* Flag to enable additional fields in struct ethtool_rx_flow_spec */
|
|
#define FLOW_EXT 0x80000000
|
|
|
|
/* L3-L4 network traffic flow hash options */
|
|
#define RXH_L2DA (1 << 1)
|
|
#define RXH_VLAN (1 << 2)
|
|
#define RXH_L3_PROTO (1 << 3)
|
|
#define RXH_IP_SRC (1 << 4)
|
|
#define RXH_IP_DST (1 << 5)
|
|
#define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */
|
|
#define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */
|
|
#define RXH_DISCARD (1 << 31)
|
|
|
|
#define RX_CLS_FLOW_DISC 0xffffffffffffffffULL
|
|
|
|
/* Reset flags */
|
|
/* The reset() operation must clear the flags for the components which
|
|
* were actually reset. On successful return, the flags indicate the
|
|
* components which were not reset, either because they do not exist
|
|
* in the hardware or because they cannot be reset independently. The
|
|
* driver must never reset any components that were not requested.
|
|
*/
|
|
enum ethtool_reset_flags {
|
|
/* These flags represent components dedicated to the interface
|
|
* the command is addressed to. Shift any flag left by
|
|
* ETH_RESET_SHARED_SHIFT to reset a shared component of the
|
|
* same type.
|
|
*/
|
|
ETH_RESET_MGMT = 1 << 0, /* Management processor */
|
|
ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */
|
|
ETH_RESET_DMA = 1 << 2, /* DMA engine */
|
|
ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */
|
|
ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */
|
|
ETH_RESET_MAC = 1 << 5, /* Media access controller */
|
|
ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */
|
|
ETH_RESET_RAM = 1 << 7, /* RAM shared between
|
|
* multiple components */
|
|
|
|
ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to
|
|
* this interface */
|
|
ETH_RESET_ALL = 0xffffffff, /* All components used by this
|
|
* interface, even if shared */
|
|
};
|
|
#define ETH_RESET_SHARED_SHIFT 16
|
|
|
|
#endif /* _LINUX_ETHTOOL_H */
|