194 lines
5.4 KiB
C
194 lines
5.4 KiB
C
/*
|
|
* Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
|
|
*
|
|
* Previous incarnations were:
|
|
* Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
|
|
* Copied and modified Carsten Langgaard's time.c
|
|
*
|
|
* Carsten Langgaard, carstenl@mips.com
|
|
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
|
|
*
|
|
* ########################################################################
|
|
*
|
|
* This program is free software; you can distribute it and/or modify it
|
|
* under the terms of the GNU General Public License (Version 2) as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope it will be useful, but WITHOUT
|
|
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
|
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
|
|
* for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License along
|
|
* with this program; if not, write to the Free Software Foundation, Inc.,
|
|
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
|
|
*
|
|
* ########################################################################
|
|
*
|
|
* Clocksource/event using the 32.768kHz-clocked Counter1 ('RTC' in the
|
|
* databooks). Firmware/Board init code must enable the counters in the
|
|
* counter control register, otherwise the CP0 counter clocksource/event
|
|
* will be installed instead (and use of 'wait' instruction is prohibited).
|
|
*/
|
|
|
|
#include <linux/clockchips.h>
|
|
#include <linux/clocksource.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/spinlock.h>
|
|
|
|
#include <asm/processor.h>
|
|
#include <asm/time.h>
|
|
#include <asm/mach-au1x00/au1000.h>
|
|
|
|
/* 32kHz clock enabled and detected */
|
|
#define CNTR_OK (SYS_CNTRL_E0 | SYS_CNTRL_32S)
|
|
|
|
static cycle_t au1x_counter1_read(struct clocksource *cs)
|
|
{
|
|
return au_readl(SYS_RTCREAD);
|
|
}
|
|
|
|
static struct clocksource au1x_counter1_clocksource = {
|
|
.name = "alchemy-counter1",
|
|
.read = au1x_counter1_read,
|
|
.mask = CLOCKSOURCE_MASK(32),
|
|
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
|
|
.rating = 100,
|
|
};
|
|
|
|
static int au1x_rtcmatch2_set_next_event(unsigned long delta,
|
|
struct clock_event_device *cd)
|
|
{
|
|
delta += au_readl(SYS_RTCREAD);
|
|
/* wait for register access */
|
|
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M21)
|
|
;
|
|
au_writel(delta, SYS_RTCMATCH2);
|
|
au_sync();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void au1x_rtcmatch2_set_mode(enum clock_event_mode mode,
|
|
struct clock_event_device *cd)
|
|
{
|
|
}
|
|
|
|
static irqreturn_t au1x_rtcmatch2_irq(int irq, void *dev_id)
|
|
{
|
|
struct clock_event_device *cd = dev_id;
|
|
cd->event_handler(cd);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static struct clock_event_device au1x_rtcmatch2_clockdev = {
|
|
.name = "rtcmatch2",
|
|
.features = CLOCK_EVT_FEAT_ONESHOT,
|
|
.rating = 100,
|
|
.set_next_event = au1x_rtcmatch2_set_next_event,
|
|
.set_mode = au1x_rtcmatch2_set_mode,
|
|
.cpumask = cpu_all_mask,
|
|
};
|
|
|
|
static struct irqaction au1x_rtcmatch2_irqaction = {
|
|
.handler = au1x_rtcmatch2_irq,
|
|
.flags = IRQF_TIMER,
|
|
.name = "timer",
|
|
.dev_id = &au1x_rtcmatch2_clockdev,
|
|
};
|
|
|
|
static int __init alchemy_time_init(unsigned int m2int)
|
|
{
|
|
struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
|
|
unsigned long t;
|
|
|
|
au1x_rtcmatch2_clockdev.irq = m2int;
|
|
|
|
/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
|
|
* has been detected. If so install the rtcmatch2 clocksource,
|
|
* otherwise don't bother. Note that both bits being set is by
|
|
* no means a definite guarantee that the counters actually work
|
|
* (the 32S bit seems to be stuck set to 1 once a single clock-
|
|
* edge is detected, hence the timeouts).
|
|
*/
|
|
if (CNTR_OK != (au_readl(SYS_COUNTER_CNTRL) & CNTR_OK))
|
|
goto cntr_err;
|
|
|
|
/*
|
|
* setup counter 1 (RTC) to tick at full speed
|
|
*/
|
|
t = 0xffffff;
|
|
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_T1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
|
|
au_writel(0, SYS_RTCTRIM); /* 32.768 kHz */
|
|
au_sync();
|
|
|
|
t = 0xffffff;
|
|
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
au_writel(0, SYS_RTCWRITE);
|
|
au_sync();
|
|
|
|
t = 0xffffff;
|
|
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
|
|
/* register counter1 clocksource and event device */
|
|
clocksource_register_hz(&au1x_counter1_clocksource, 32768);
|
|
|
|
cd->shift = 32;
|
|
cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift);
|
|
cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
|
|
cd->min_delta_ns = clockevent_delta2ns(8, cd); /* ~0.25ms */
|
|
clockevents_register_device(cd);
|
|
setup_irq(m2int, &au1x_rtcmatch2_irqaction);
|
|
|
|
printk(KERN_INFO "Alchemy clocksource installed\n");
|
|
|
|
return 0;
|
|
|
|
cntr_err:
|
|
return -1;
|
|
}
|
|
|
|
static void __init alchemy_setup_c0timer(void)
|
|
{
|
|
/*
|
|
* MIPS kernel assigns 'au1k_wait' to 'cpu_wait' before this
|
|
* function is called. Because the Alchemy counters are unusable
|
|
* the C0 timekeeping code is installed and use of the 'wait'
|
|
* instruction must be prohibited, which is done most easily by
|
|
* assigning NULL to cpu_wait.
|
|
*/
|
|
cpu_wait = NULL;
|
|
r4k_clockevent_init();
|
|
init_r4k_clocksource();
|
|
}
|
|
|
|
static int alchemy_m2inttab[] __initdata = {
|
|
AU1000_RTC_MATCH2_INT,
|
|
AU1500_RTC_MATCH2_INT,
|
|
AU1100_RTC_MATCH2_INT,
|
|
AU1550_RTC_MATCH2_INT,
|
|
AU1200_RTC_MATCH2_INT,
|
|
AU1300_RTC_MATCH2_INT,
|
|
};
|
|
|
|
void __init plat_time_init(void)
|
|
{
|
|
int t;
|
|
|
|
t = alchemy_get_cputype();
|
|
if (t == ALCHEMY_CPU_UNKNOWN)
|
|
alchemy_setup_c0timer();
|
|
else if (alchemy_time_init(alchemy_m2inttab[t]))
|
|
alchemy_setup_c0timer();
|
|
}
|