f67f6c00c7
Rather than call the internal s3c_gpio_cfgall_range() function through a platform header, move the code into the set_power callback that is already exported by the board, and add a default implementation. In DT mode, the code already does not set the pin config, so nothing changes there. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200806182059.2431-29-krzk@kernel.org [krzk: Rebase and correct set_power in mach-h1940.c] Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
52 lines
2 KiB
C
52 lines
2 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
#ifndef _ARCH_MCI_H
|
|
#define _ARCH_MCI_H
|
|
|
|
/**
|
|
* struct s3c24xx_mci_pdata - sd/mmc controller platform data
|
|
* @no_wprotect: Set this to indicate there is no write-protect switch.
|
|
* @no_detect: Set this if there is no detect switch.
|
|
* @wprotect_invert: Invert the default sense of the write protect switch.
|
|
* @use_dma: Set to allow the use of DMA.
|
|
* @gpio_detect: GPIO number for the card detect line.
|
|
* @gpio_wprotect: GPIO number for the write protect line.
|
|
* @ocr_avail: The mask of the available power states, non-zero to use.
|
|
* @set_power: Callback to control the power mode.
|
|
*
|
|
* The @gpio_detect is used for card detection when @no_wprotect is unset,
|
|
* and the default sense is that 0 returned from gpio_get_value() means
|
|
* that a card is inserted. If @detect_invert is set, then the value from
|
|
* gpio_get_value() is inverted, which makes 1 mean card inserted.
|
|
*
|
|
* The driver will use @gpio_wprotect to signal whether the card is write
|
|
* protected if @no_wprotect is not set. A 0 returned from gpio_get_value()
|
|
* means the card is read/write, and 1 means read-only. The @wprotect_invert
|
|
* will invert the value returned from gpio_get_value().
|
|
*
|
|
* Card power is set by @ocr_availa, using MCC_VDD_ constants if it is set
|
|
* to a non-zero value, otherwise the default of 3.2-3.4V is used.
|
|
*/
|
|
struct s3c24xx_mci_pdata {
|
|
unsigned int no_wprotect:1;
|
|
unsigned int no_detect:1;
|
|
unsigned int wprotect_invert:1;
|
|
unsigned int use_dma:1;
|
|
|
|
unsigned long ocr_avail;
|
|
void (*set_power)(unsigned char power_mode,
|
|
unsigned short vdd);
|
|
struct gpio_desc *bus[6];
|
|
};
|
|
|
|
/**
|
|
* s3c24xx_mci_set_platdata - set platform data for mmc/sdi device
|
|
* @pdata: The platform data
|
|
*
|
|
* Copy the platform data supplied by @pdata so that this can be marked
|
|
* __initdata.
|
|
*/
|
|
extern void s3c24xx_mci_def_set_power(unsigned char power_mode, unsigned short vdd);
|
|
extern void s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata);
|
|
|
|
#endif /* _ARCH_NCI_H */
|