c99993376f
Adds support for Amlogic G12A USB Control Glue HW. The Amlogic G12A SoC Family embeds 2 USB Controllers : - a DWC3 IP configured as Host for USB2 and USB3 - a DWC2 IP configured as Peripheral USB2 Only A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller. The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY. This drivers supports the on-probe setup of the OTG mode, and manually via a debugfs interface. The IRQ mode change detect is yet to be added in a future patchset, mainly due to lack of hardware to validate on. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
54 lines
1.4 KiB
Makefile
54 lines
1.4 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0
|
|
# define_trace.h needs to know how to find our header
|
|
CFLAGS_trace.o := -I$(src)
|
|
|
|
obj-$(CONFIG_USB_DWC3) += dwc3.o
|
|
|
|
dwc3-y := core.o
|
|
|
|
ifneq ($(CONFIG_TRACING),)
|
|
dwc3-y += trace.o
|
|
endif
|
|
|
|
ifneq ($(filter y,$(CONFIG_USB_DWC3_HOST) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
|
|
dwc3-y += host.o
|
|
endif
|
|
|
|
ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
|
|
dwc3-y += gadget.o ep0.o
|
|
endif
|
|
|
|
ifneq ($(CONFIG_USB_DWC3_DUAL_ROLE),)
|
|
dwc3-y += drd.o
|
|
endif
|
|
|
|
ifneq ($(CONFIG_USB_DWC3_ULPI),)
|
|
dwc3-y += ulpi.o
|
|
endif
|
|
|
|
ifneq ($(CONFIG_DEBUG_FS),)
|
|
dwc3-y += debugfs.o
|
|
endif
|
|
|
|
##
|
|
# Platform-specific glue layers go here
|
|
#
|
|
# NOTICE: Make sure your glue layer doesn't depend on anything
|
|
# which is arch-specific and that it compiles on all situations.
|
|
#
|
|
# We want to keep this requirement in order to be able to compile
|
|
# the entire driver (with all its glue layers) on several architectures
|
|
# and make sure it compiles fine. This will also help with allmodconfig
|
|
# and allyesconfig builds.
|
|
##
|
|
|
|
obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
|
|
obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
|
|
obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
|
|
obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
|
|
obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
|
|
obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
|
|
obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
|
|
obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
|
|
obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
|