9c569b3909
This patch enables the phy drivers for the SATA controller on Marvell's 88f6192. Without them it is not possible to use SATA drives attached to this processor. Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
87 lines
2.1 KiB
Plaintext
87 lines
2.1 KiB
Plaintext
/ {
|
|
mbus {
|
|
pciec: pcie-controller {
|
|
compatible = "marvell,kirkwood-pcie";
|
|
status = "disabled";
|
|
device_type = "pci";
|
|
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
|
|
bus-range = <0x00 0xff>;
|
|
|
|
ranges =
|
|
<0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
|
|
0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
|
|
0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
|
|
|
|
pcie0: pcie@1,0 {
|
|
device_type = "pci";
|
|
assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
|
|
reg = <0x0800 0 0 0 0>;
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
#interrupt-cells = <1>;
|
|
ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
|
|
0x81000000 0 0 0x81000000 0x1 0 1 0>;
|
|
interrupt-map-mask = <0 0 0 0>;
|
|
interrupt-map = <0 0 0 0 &intc 9>;
|
|
marvell,pcie-port = <0>;
|
|
marvell,pcie-lane = <0>;
|
|
clocks = <&gate_clk 2>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
pinctrl: pin-controller@10000 {
|
|
compatible = "marvell,88f6192-pinctrl";
|
|
|
|
pmx_sata0: pmx-sata0 {
|
|
marvell,pins = "mpp5", "mpp21", "mpp23";
|
|
marvell,function = "sata0";
|
|
};
|
|
pmx_sata1: pmx-sata1 {
|
|
marvell,pins = "mpp4", "mpp20", "mpp22";
|
|
marvell,function = "sata1";
|
|
};
|
|
pmx_sdio: pmx-sdio {
|
|
marvell,pins = "mpp12", "mpp13", "mpp14",
|
|
"mpp15", "mpp16", "mpp17";
|
|
marvell,function = "sdio";
|
|
};
|
|
};
|
|
|
|
rtc: rtc@10300 {
|
|
compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
|
|
reg = <0x10300 0x20>;
|
|
interrupts = <53>;
|
|
clocks = <&gate_clk 7>;
|
|
};
|
|
|
|
sata: sata@80000 {
|
|
compatible = "marvell,orion-sata";
|
|
reg = <0x80000 0x5000>;
|
|
interrupts = <21>;
|
|
clocks = <&gate_clk 14>, <&gate_clk 15>;
|
|
clock-names = "0", "1";
|
|
phys = <&sata_phy0>, <&sata_phy1>;
|
|
phy-names = "port0", "port1";
|
|
status = "disabled";
|
|
};
|
|
|
|
sdio: mvsdio@90000 {
|
|
compatible = "marvell,orion-sdio";
|
|
reg = <0x90000 0x200>;
|
|
interrupts = <28>;
|
|
clocks = <&gate_clk 4>;
|
|
bus-width = <4>;
|
|
cap-sdio-irq;
|
|
cap-sd-highspeed;
|
|
cap-mmc-highspeed;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|