332 lines
8.1 KiB
C
332 lines
8.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
||
/*
|
||
* FB driver for the UltraChip UC1611 LCD controller
|
||
*
|
||
* The display is 4-bit grayscale (16 shades) 240x160.
|
||
*
|
||
* Copyright (C) 2015 Henri Chain
|
||
*/
|
||
|
||
#include <linux/module.h>
|
||
#include <linux/kernel.h>
|
||
#include <linux/init.h>
|
||
#include <linux/gpio/consumer.h>
|
||
#include <linux/spi/spi.h>
|
||
#include <linux/delay.h>
|
||
|
||
#include "fbtft.h"
|
||
|
||
#define DRVNAME "fb_uc1611"
|
||
#define WIDTH 240
|
||
#define HEIGHT 160
|
||
#define BPP 8
|
||
#define FPS 40
|
||
|
||
/*
|
||
* LCD voltage is a combination of ratio, gain, pot and temp
|
||
*
|
||
* V_LCD = V_BIAS * ratio
|
||
* V_LCD = (C_V0 + C_PM × pot) * (1 + (T - 25) * temp)
|
||
* C_V0 and C_PM depend on ratio and gain
|
||
* T is ambient temperature
|
||
*/
|
||
|
||
/* BR -> actual ratio: 0-3 -> 5, 10, 11, 13 */
|
||
static unsigned int ratio = 2;
|
||
module_param(ratio, uint, 0000);
|
||
MODULE_PARM_DESC(ratio, "BR[1:0] Bias voltage ratio: 0-3 (default: 2)");
|
||
|
||
static unsigned int gain = 3;
|
||
module_param(gain, uint, 0000);
|
||
MODULE_PARM_DESC(gain, "GN[1:0] Bias voltage gain: 0-3 (default: 3)");
|
||
|
||
static unsigned int pot = 16;
|
||
module_param(pot, uint, 0000);
|
||
MODULE_PARM_DESC(pot, "PM[6:0] Bias voltage pot.: 0-63 (default: 16)");
|
||
|
||
/* TC -> % compensation per deg C: 0-3 -> -.05, -.10, -.015, -.20 */
|
||
static unsigned int temp;
|
||
module_param(temp, uint, 0000);
|
||
MODULE_PARM_DESC(temp, "TC[1:0] Temperature compensation: 0-3 (default: 0)");
|
||
|
||
/* PC[1:0] -> LCD capacitance: 0-3 -> <20nF, 20-28 nF, 29-40 nF, 40-56 nF */
|
||
static unsigned int load = 1;
|
||
module_param(load, uint, 0000);
|
||
MODULE_PARM_DESC(load, "PC[1:0] Panel Loading: 0-3 (default: 1)");
|
||
|
||
/* PC[3:2] -> V_LCD: 0, 1, 3 -> ext., int. with ratio = 5, int. standard */
|
||
static unsigned int pump = 3;
|
||
module_param(pump, uint, 0000);
|
||
MODULE_PARM_DESC(pump, "PC[3:2] Pump control: 0,1,3 (default: 3)");
|
||
|
||
static int init_display(struct fbtft_par *par)
|
||
{
|
||
int ret;
|
||
|
||
/* Set CS active high */
|
||
par->spi->mode |= SPI_CS_HIGH;
|
||
ret = spi_setup(par->spi);
|
||
if (ret) {
|
||
dev_err(par->info->device, "Could not set SPI_CS_HIGH\n");
|
||
return ret;
|
||
}
|
||
|
||
/* Reset controller */
|
||
write_reg(par, 0xE2);
|
||
|
||
/* Set bias ratio */
|
||
write_reg(par, 0xE8 | (ratio & 0x03));
|
||
|
||
/* Set bias gain and potentiometer */
|
||
write_reg(par, 0x81);
|
||
write_reg(par, (gain & 0x03) << 6 | (pot & 0x3F));
|
||
|
||
/* Set temperature compensation */
|
||
write_reg(par, 0x24 | (temp & 0x03));
|
||
|
||
/* Set panel loading */
|
||
write_reg(par, 0x28 | (load & 0x03));
|
||
|
||
/* Set pump control */
|
||
write_reg(par, 0x2C | (pump & 0x03));
|
||
|
||
/* Set inverse display */
|
||
write_reg(par, 0xA6 | (0x01 & 0x01));
|
||
|
||
/* Set 4-bit grayscale mode */
|
||
write_reg(par, 0xD0 | (0x02 & 0x03));
|
||
|
||
/* Set Display enable */
|
||
write_reg(par, 0xA8 | 0x07);
|
||
|
||
return 0;
|
||
}
|
||
|
||
static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
|
||
{
|
||
switch (par->info->var.rotate) {
|
||
case 90:
|
||
case 270:
|
||
/* Set column address */
|
||
write_reg(par, ys & 0x0F);
|
||
write_reg(par, 0x10 | (ys >> 4));
|
||
|
||
/* Set page address (divide xs by 2) (not used by driver) */
|
||
write_reg(par, 0x60 | ((xs >> 1) & 0x0F));
|
||
write_reg(par, 0x70 | (xs >> 5));
|
||
break;
|
||
default:
|
||
/* Set column address (not used by driver) */
|
||
write_reg(par, xs & 0x0F);
|
||
write_reg(par, 0x10 | (xs >> 4));
|
||
|
||
/* Set page address (divide ys by 2) */
|
||
write_reg(par, 0x60 | ((ys >> 1) & 0x0F));
|
||
write_reg(par, 0x70 | (ys >> 5));
|
||
break;
|
||
}
|
||
}
|
||
|
||
static int blank(struct fbtft_par *par, bool on)
|
||
{
|
||
fbtft_par_dbg(DEBUG_BLANK, par, "(%s=%s)\n",
|
||
__func__, on ? "true" : "false");
|
||
|
||
if (on)
|
||
write_reg(par, 0xA8 | 0x00);
|
||
else
|
||
write_reg(par, 0xA8 | 0x07);
|
||
return 0;
|
||
}
|
||
|
||
static int set_var(struct fbtft_par *par)
|
||
{
|
||
/* par->info->fix.visual = FB_VISUAL_PSEUDOCOLOR; */
|
||
par->info->var.grayscale = 1;
|
||
par->info->var.red.offset = 0;
|
||
par->info->var.red.length = 8;
|
||
par->info->var.green.offset = 0;
|
||
par->info->var.green.length = 8;
|
||
par->info->var.blue.offset = 0;
|
||
par->info->var.blue.length = 8;
|
||
par->info->var.transp.offset = 0;
|
||
par->info->var.transp.length = 0;
|
||
|
||
switch (par->info->var.rotate) {
|
||
case 90:
|
||
/* Set RAM address control */
|
||
write_reg(par, 0x88
|
||
| (0x0 & 0x1) << 2 /* Increment positively */
|
||
| (0x1 & 0x1) << 1 /* Increment page first */
|
||
| (0x1 & 0x1)); /* Wrap around (default) */
|
||
|
||
/* Set LCD mapping */
|
||
write_reg(par, 0xC0
|
||
| (0x0 & 0x1) << 2 /* Mirror Y OFF */
|
||
| (0x0 & 0x1) << 1 /* Mirror X OFF */
|
||
| (0x0 & 0x1)); /* MS nibble last (default) */
|
||
break;
|
||
case 180:
|
||
/* Set RAM address control */
|
||
write_reg(par, 0x88
|
||
| (0x0 & 0x1) << 2 /* Increment positively */
|
||
| (0x0 & 0x1) << 1 /* Increment column first */
|
||
| (0x1 & 0x1)); /* Wrap around (default) */
|
||
|
||
/* Set LCD mapping */
|
||
write_reg(par, 0xC0
|
||
| (0x1 & 0x1) << 2 /* Mirror Y ON */
|
||
| (0x0 & 0x1) << 1 /* Mirror X OFF */
|
||
| (0x0 & 0x1)); /* MS nibble last (default) */
|
||
break;
|
||
case 270:
|
||
/* Set RAM address control */
|
||
write_reg(par, 0x88
|
||
| (0x0 & 0x1) << 2 /* Increment positively */
|
||
| (0x1 & 0x1) << 1 /* Increment page first */
|
||
| (0x1 & 0x1)); /* Wrap around (default) */
|
||
|
||
/* Set LCD mapping */
|
||
write_reg(par, 0xC0
|
||
| (0x1 & 0x1) << 2 /* Mirror Y ON */
|
||
| (0x1 & 0x1) << 1 /* Mirror X ON */
|
||
| (0x0 & 0x1)); /* MS nibble last (default) */
|
||
break;
|
||
default:
|
||
/* Set RAM address control */
|
||
write_reg(par, 0x88
|
||
| (0x0 & 0x1) << 2 /* Increment positively */
|
||
| (0x0 & 0x1) << 1 /* Increment column first */
|
||
| (0x1 & 0x1)); /* Wrap around (default) */
|
||
|
||
/* Set LCD mapping */
|
||
write_reg(par, 0xC0
|
||
| (0x0 & 0x1) << 2 /* Mirror Y OFF */
|
||
| (0x1 & 0x1) << 1 /* Mirror X ON */
|
||
| (0x0 & 0x1)); /* MS nibble last (default) */
|
||
break;
|
||
}
|
||
|
||
return 0;
|
||
}
|
||
|
||
static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
|
||
{
|
||
u8 *vmem8 = (u8 *)(par->info->screen_buffer);
|
||
u8 *buf8 = par->txbuf.buf;
|
||
u16 *buf16 = par->txbuf.buf;
|
||
int line_length = par->info->fix.line_length;
|
||
int y_start = offset / line_length;
|
||
int y_end = (offset + len - 1) / line_length;
|
||
int x, y, i;
|
||
int ret = 0;
|
||
|
||
switch (par->pdata->display.buswidth) {
|
||
case 8:
|
||
switch (par->info->var.rotate) {
|
||
case 90:
|
||
case 270:
|
||
i = y_start * line_length;
|
||
for (y = y_start; y <= y_end; y++) {
|
||
for (x = 0; x < line_length; x += 2) {
|
||
*buf8 = vmem8[i] >> 4;
|
||
*buf8 |= vmem8[i + 1] & 0xF0;
|
||
buf8++;
|
||
i += 2;
|
||
}
|
||
}
|
||
break;
|
||
default:
|
||
/* Must be even because pages are two lines */
|
||
y_start &= 0xFE;
|
||
i = y_start * line_length;
|
||
for (y = y_start; y <= y_end; y += 2) {
|
||
for (x = 0; x < line_length; x++) {
|
||
*buf8 = vmem8[i] >> 4;
|
||
*buf8 |= vmem8[i + line_length] & 0xF0;
|
||
buf8++;
|
||
i++;
|
||
}
|
||
i += line_length;
|
||
}
|
||
break;
|
||
}
|
||
gpiod_set_value(par->gpio.dc, 1);
|
||
|
||
/* Write data */
|
||
ret = par->fbtftops.write(par, par->txbuf.buf, len / 2);
|
||
break;
|
||
case 9:
|
||
switch (par->info->var.rotate) {
|
||
case 90:
|
||
case 270:
|
||
i = y_start * line_length;
|
||
for (y = y_start; y <= y_end; y++) {
|
||
for (x = 0; x < line_length; x += 2) {
|
||
*buf16 = 0x100;
|
||
*buf16 |= vmem8[i] >> 4;
|
||
*buf16 |= vmem8[i + 1] & 0xF0;
|
||
buf16++;
|
||
i += 2;
|
||
}
|
||
}
|
||
break;
|
||
default:
|
||
/* Must be even because pages are two lines */
|
||
y_start &= 0xFE;
|
||
i = y_start * line_length;
|
||
for (y = y_start; y <= y_end; y += 2) {
|
||
for (x = 0; x < line_length; x++) {
|
||
*buf16 = 0x100;
|
||
*buf16 |= vmem8[i] >> 4;
|
||
*buf16 |= vmem8[i + line_length] & 0xF0;
|
||
buf16++;
|
||
i++;
|
||
}
|
||
i += line_length;
|
||
}
|
||
break;
|
||
}
|
||
|
||
/* Write data */
|
||
ret = par->fbtftops.write(par, par->txbuf.buf, len);
|
||
break;
|
||
default:
|
||
dev_err(par->info->device, "unsupported buswidth %d\n",
|
||
par->pdata->display.buswidth);
|
||
}
|
||
|
||
if (ret < 0)
|
||
dev_err(par->info->device, "write failed and returned: %d\n",
|
||
ret);
|
||
|
||
return ret;
|
||
}
|
||
|
||
static struct fbtft_display display = {
|
||
.txbuflen = -1,
|
||
.regwidth = 8,
|
||
.width = WIDTH,
|
||
.height = HEIGHT,
|
||
.bpp = BPP,
|
||
.fps = FPS,
|
||
.fbtftops = {
|
||
.write_vmem = write_vmem,
|
||
.init_display = init_display,
|
||
.set_addr_win = set_addr_win,
|
||
.set_var = set_var,
|
||
.blank = blank,
|
||
},
|
||
};
|
||
|
||
FBTFT_REGISTER_DRIVER(DRVNAME, "ultrachip,uc1611", &display);
|
||
|
||
MODULE_ALIAS("spi:" DRVNAME);
|
||
MODULE_ALIAS("platform:" DRVNAME);
|
||
MODULE_ALIAS("spi:uc1611");
|
||
MODULE_ALIAS("platform:uc1611");
|
||
|
||
MODULE_DESCRIPTION("FB driver for the UC1611 LCD controller");
|
||
MODULE_AUTHOR("Henri Chain");
|
||
MODULE_LICENSE("GPL");
|