redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/arch/sh/Makefile
Rich Felker 5a846abad0 sh: add support for J-Core J2 processor 
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.

Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.

No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.

Signed-off-by: Rich Felker <dalias@libc.org>
2016-08-05 03:29:31 +00:00

242 lines
8.1 KiB
Makefile
Raw Blame History

#
# arch/sh/Makefile
#
# Copyright (C) 1999 Kaz Kojima
# Copyright (C) 2002 - 2008 Paul Mundt
# Copyright (C) 2002 M. R. Brown
#
# This file is subject to the terms and conditions of the GNU General Public
# License. See the file "COPYING" in the main directory of this archive
# for more details.
#
ifneq ($(SUBARCH),$(ARCH))
ifeq ($(CROSS_COMPILE),)
CROSS_COMPILE := $(call cc-cross-prefix, $(UTS_MACHINE)-linux- $(UTS_MACHINE)-linux-gnu- $(UTS_MACHINE)-unknown-linux-gnu-)
endif
endif
isa-y := any
isa-$(CONFIG_SH_DSP) := sh
isa-$(CONFIG_CPU_SH2) := sh2
isa-$(CONFIG_CPU_SH2A) := sh2a
isa-$(CONFIG_CPU_SH3) := sh3
isa-$(CONFIG_CPU_SH4) := sh4
isa-$(CONFIG_CPU_SH4A) := sh4a
isa-$(CONFIG_CPU_SH4AL_DSP) := sh4al
isa-$(CONFIG_CPU_SH5) := shmedia
ifeq ($(CONFIG_SUPERH32),y)
isa-$(CONFIG_SH_DSP) := $(isa-y)-dsp
isa-y := $(isa-y)-up
endif
cflags-$(CONFIG_CPU_SH2) := $(call cc-option,-m2,)
cflags-$(CONFIG_CPU_J2) := $(call cc-option,-mj2,)
cflags-$(CONFIG_CPU_SH2A) += $(call cc-option,-m2a,) \
$(call cc-option,-m2a-nofpu,) \
$(call cc-option,-m4-nofpu,)
cflags-$(CONFIG_CPU_SH3) := $(call cc-option,-m3,)
cflags-$(CONFIG_CPU_SH4) := $(call cc-option,-m4,) \
$(call cc-option,-mno-implicit-fp,-m4-nofpu)
cflags-$(CONFIG_CPU_SH4A) += $(call cc-option,-m4a,) \
$(call cc-option,-m4a-nofpu,)
cflags-$(CONFIG_CPU_SH4AL_DSP) += $(call cc-option,-m4al,)
cflags-$(CONFIG_CPU_SH5) := $(call cc-option,-m5-32media-nofpu,)
ifeq ($(cflags-y),)
#
# In the case where we are stuck with a compiler that has been uselessly
# restricted to a particular ISA, a favourite default of newer GCCs when
# extensive multilib targets are not provided, ensure we get the best fit
# regarding FP generation. This is intentionally stupid (albeit many
# orders of magnitude less than GCC's default behaviour), as anything
# with a large number of multilib targets better have been built
# correctly for the target in mind.
#
cflags-y += $(shell $(CC) $(KBUILD_CFLAGS) -print-multi-lib | \
grep nofpu | sed q | sed -e 's/^/-/;s/;.*$$//')
# At this point, anything goes.
isaflags-y := $(call as-option,-Wa$(comma)-isa=any,)
else
#
# -Wa,-isa= tuning implies -Wa,-dsp for the versions of binutils that
# support it, while -Wa,-dsp by itself limits the range of usable opcodes
# on certain CPU subtypes. Try the ISA variant first, and if that fails,
# fall back on -Wa,-dsp for the old binutils versions. Even without DSP
# opcodes, we always want the best ISA tuning the version of binutils
# will provide.
#
isaflags-y := $(call as-option,-Wa$(comma)-isa=$(isa-y),)
isaflags-$(CONFIG_SH_DSP) := \
$(call as-option,-Wa$(comma)-isa=$(isa-y),-Wa$(comma)-dsp)
endif
cflags-$(CONFIG_CPU_BIG_ENDIAN) += -mb
cflags-$(CONFIG_CPU_LITTLE_ENDIAN) += -ml
cflags-y += $(call cc-option,-mno-fdpic)
cflags-y += $(isaflags-y) -ffreestanding
OBJCOPYFLAGS := -O binary -R .note -R .note.gnu.build-id -R .comment \
-R .stab -R .stabstr -S
# Give the various platforms the opportunity to set default image types
defaultimage-$(CONFIG_SUPERH32) := zImage
defaultimage-$(CONFIG_SH_SH7785LCR) := uImage
defaultimage-$(CONFIG_SH_RSK) := uImage
defaultimage-$(CONFIG_SH_URQUELL) := uImage
defaultimage-$(CONFIG_SH_MIGOR) := uImage
defaultimage-$(CONFIG_SH_AP325RXA) := uImage
defaultimage-$(CONFIG_SH_SH7757LCR) := uImage
defaultimage-$(CONFIG_SH_7724_SOLUTION_ENGINE) := uImage
defaultimage-$(CONFIG_SH_7206_SOLUTION_ENGINE) := vmlinux
defaultimage-$(CONFIG_SH_7619_SOLUTION_ENGINE) := vmlinux
# Set some sensible Kbuild defaults
KBUILD_IMAGE := $(defaultimage-y)
#
# Choosing incompatible machines durings configuration will result in
# error messages during linking.
#
ifdef CONFIG_SUPERH32
UTS_MACHINE := sh
BITS := 32
LDFLAGS_vmlinux += -e _stext
KBUILD_DEFCONFIG := shx3_defconfig
else
UTS_MACHINE := sh64
BITS := 64
LDFLAGS_vmlinux += --defsym phys_stext=_stext-$(CONFIG_PAGE_OFFSET) \
--defsym phys_stext_shmedia=phys_stext+1 \
-e phys_stext_shmedia
KBUILD_DEFCONFIG := cayman_defconfig
endif
ifdef CONFIG_CPU_LITTLE_ENDIAN
ld-bfd := elf32-$(UTS_MACHINE)-linux
LDFLAGS_vmlinux += --defsym jiffies=jiffies_64 --oformat $(ld-bfd)
LDFLAGS += -EL
else
ld-bfd := elf32-$(UTS_MACHINE)big-linux
LDFLAGS_vmlinux += --defsym jiffies=jiffies_64+4 --oformat $(ld-bfd)
LDFLAGS += -EB
endif
export ld-bfd BITS
head-y := arch/sh/kernel/head_$(BITS).o
core-y += arch/sh/kernel/ arch/sh/mm/ arch/sh/boards/
core-$(CONFIG_SH_FPU_EMU) += arch/sh/math-emu/
core-$(CONFIG_USE_BUILTIN_DTB) += arch/sh/boot/dts/
# Mach groups
machdir-$(CONFIG_SOLUTION_ENGINE) += mach-se
machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx
machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast
machdir-$(CONFIG_SH_SH03) += mach-sh03
machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d
machdir-$(CONFIG_SH_HIGHLANDER) += mach-highlander
machdir-$(CONFIG_SH_MIGOR) += mach-migor
machdir-$(CONFIG_SH_AP325RXA) += mach-ap325rxa
machdir-$(CONFIG_SH_KFR2R09) += mach-kfr2r09
machdir-$(CONFIG_SH_ECOVEC) += mach-ecovec24
machdir-$(CONFIG_SH_SDK7780) += mach-sdk7780
machdir-$(CONFIG_SH_SDK7786) += mach-sdk7786
machdir-$(CONFIG_SH_X3PROTO) += mach-x3proto
machdir-$(CONFIG_SH_SH7763RDP) += mach-sh7763rdp
machdir-$(CONFIG_SH_SH4202_MICRODEV) += mach-microdev
machdir-$(CONFIG_SH_LANDISK) += mach-landisk
machdir-$(CONFIG_SH_LBOX_RE2) += mach-lboxre2
machdir-$(CONFIG_SH_CAYMAN) += mach-cayman
machdir-$(CONFIG_SH_RSK) += mach-rsk
ifneq ($(machdir-y),)
core-y += $(addprefix arch/sh/boards/, \
$(filter-out ., $(patsubst %,%/,$(machdir-y))))
endif
# Common machine type headers. Not part of the arch/sh/boards/ hierarchy.
machdir-y += mach-common
# Companion chips
core-$(CONFIG_HD6446X_SERIES) += arch/sh/cchips/hd6446x/
#
# CPU header paths
#
# These are ordered by optimization level. A CPU family that is a subset
# of another (ie, SH-2A / SH-2), is picked up first, with increasing
# levels of genericness if nothing more suitable is situated in the
# hierarchy.
#
# As an example, in order of preference, SH-2A > SH-2 > common definitions.
#
cpuincdir-$(CONFIG_CPU_SH2A) += cpu-sh2a
cpuincdir-$(CONFIG_CPU_SH2) += cpu-sh2
cpuincdir-$(CONFIG_CPU_SH3) += cpu-sh3
cpuincdir-$(CONFIG_CPU_SH4A) += cpu-sh4a
cpuincdir-$(CONFIG_CPU_SH4) += cpu-sh4
cpuincdir-$(CONFIG_CPU_SH5) += cpu-sh5
cpuincdir-y += cpu-common # Must be last
drivers-y += arch/sh/drivers/
drivers-$(CONFIG_OPROFILE) += arch/sh/oprofile/
boot := arch/sh/boot
cflags-y += $(foreach d, $(cpuincdir-y), -Iarch/sh/include/$(d)) \
$(foreach d, $(machdir-y), -Iarch/sh/include/$(d))
KBUILD_CFLAGS += -pipe $(cflags-y)
KBUILD_CPPFLAGS += $(cflags-y)
KBUILD_AFLAGS += $(cflags-y)
ifeq ($(CONFIG_MCOUNT),y)
KBUILD_CFLAGS += -pg
endif
ifeq ($(CONFIG_DWARF_UNWINDER),y)
KBUILD_CFLAGS += -fasynchronous-unwind-tables
endif
libs-$(CONFIG_SUPERH32) := arch/sh/lib/ $(libs-y)
libs-$(CONFIG_SUPERH64) := arch/sh/lib64/ $(libs-y)
BOOT_TARGETS = uImage uImage.bz2 uImage.gz uImage.lzma uImage.xz uImage.lzo \
uImage.srec uImage.bin zImage vmlinux.bin vmlinux.srec \
romImage
PHONY += $(BOOT_TARGETS)
all: $(KBUILD_IMAGE)
$(BOOT_TARGETS): vmlinux
$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
compressed: zImage
archprepare:
$(Q)$(MAKE) $(build)=arch/sh/tools include/generated/machtypes.h
archclean:
$(Q)$(MAKE) $(clean)=$(boot)
$(Q)$(MAKE) $(clean)=arch/sh/kernel/vsyscall
define archhelp
@echo ' zImage - Compressed kernel image'
@echo ' romImage - Compressed ROM image, if supported'
@echo ' vmlinux.srec - Create an ELF S-record'
@echo ' vmlinux.bin - Create an uncompressed binary image'
@echo '* uImage - Alias to bootable U-Boot image'
@echo ' uImage.srec - Create an S-record for U-Boot'
@echo ' uImage.bin - Kernel-only image for U-Boot (bin)'
@echo '* uImage.gz - Kernel-only image for U-Boot (gzip)'
@echo ' uImage.bz2 - Kernel-only image for U-Boot (bzip2)'
@echo ' uImage.lzma - Kernel-only image for U-Boot (lzma)'
@echo ' uImage.xz - Kernel-only image for U-Boot (xz)'
@echo ' uImage.lzo - Kernel-only image for U-Boot (lzo)'
endef
View git blame Copy permalink