![Tim Bird](/assets/img/avatar_default.png)
Select the secondary PHY using the TCSR register, if phy-num=1 in the DTS (or phy_number is set in the platform data). The SOC has 2 PHYs which can be used with the OTG port, and this code allows configuring the correct one. Note: This resolves the problem I was seeing where I couldn't get the USB driver working at all on a dragonboard, from cold boot. This patch depends on patch 5/14 from Ivan's msm USB patch set. It does not use DT for the register address, as there's no evidence that this address changes between SoC versions. Signed-off-by: Tim Bird <tim.bird@sonymobile.com> Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
1809 lines
43 KiB
C
1809 lines
43 KiB
C
/* Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
|
|
* 02110-1301, USA.
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/device.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/err.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/uaccess.h>
|
|
#include <linux/debugfs.h>
|
|
#include <linux/seq_file.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/reset.h>
|
|
|
|
#include <linux/usb.h>
|
|
#include <linux/usb/otg.h>
|
|
#include <linux/usb/of.h>
|
|
#include <linux/usb/ulpi.h>
|
|
#include <linux/usb/gadget.h>
|
|
#include <linux/usb/hcd.h>
|
|
#include <linux/usb/msm_hsusb.h>
|
|
#include <linux/usb/msm_hsusb_hw.h>
|
|
#include <linux/regulator/consumer.h>
|
|
|
|
#define MSM_USB_BASE (motg->regs)
|
|
#define DRIVER_NAME "msm_otg"
|
|
|
|
#define ULPI_IO_TIMEOUT_USEC (10 * 1000)
|
|
#define LINK_RESET_TIMEOUT_USEC (250 * 1000)
|
|
|
|
#define USB_PHY_3P3_VOL_MIN 3050000 /* uV */
|
|
#define USB_PHY_3P3_VOL_MAX 3300000 /* uV */
|
|
#define USB_PHY_3P3_HPM_LOAD 50000 /* uA */
|
|
#define USB_PHY_3P3_LPM_LOAD 4000 /* uA */
|
|
|
|
#define USB_PHY_1P8_VOL_MIN 1800000 /* uV */
|
|
#define USB_PHY_1P8_VOL_MAX 1800000 /* uV */
|
|
#define USB_PHY_1P8_HPM_LOAD 50000 /* uA */
|
|
#define USB_PHY_1P8_LPM_LOAD 4000 /* uA */
|
|
|
|
#define USB_PHY_VDD_DIG_VOL_MIN 1000000 /* uV */
|
|
#define USB_PHY_VDD_DIG_VOL_MAX 1320000 /* uV */
|
|
|
|
static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (init) {
|
|
ret = regulator_set_voltage(motg->vddcx,
|
|
USB_PHY_VDD_DIG_VOL_MIN,
|
|
USB_PHY_VDD_DIG_VOL_MAX);
|
|
if (ret) {
|
|
dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = regulator_enable(motg->vddcx);
|
|
if (ret)
|
|
dev_err(motg->phy.dev, "unable to enable hsusb vddcx\n");
|
|
} else {
|
|
ret = regulator_set_voltage(motg->vddcx, 0,
|
|
USB_PHY_VDD_DIG_VOL_MAX);
|
|
if (ret)
|
|
dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
|
|
ret = regulator_disable(motg->vddcx);
|
|
if (ret)
|
|
dev_err(motg->phy.dev, "unable to disable hsusb vddcx\n");
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)
|
|
{
|
|
int rc = 0;
|
|
|
|
if (init) {
|
|
rc = regulator_set_voltage(motg->v3p3, USB_PHY_3P3_VOL_MIN,
|
|
USB_PHY_3P3_VOL_MAX);
|
|
if (rc) {
|
|
dev_err(motg->phy.dev, "Cannot set v3p3 voltage\n");
|
|
goto exit;
|
|
}
|
|
rc = regulator_enable(motg->v3p3);
|
|
if (rc) {
|
|
dev_err(motg->phy.dev, "unable to enable the hsusb 3p3\n");
|
|
goto exit;
|
|
}
|
|
rc = regulator_set_voltage(motg->v1p8, USB_PHY_1P8_VOL_MIN,
|
|
USB_PHY_1P8_VOL_MAX);
|
|
if (rc) {
|
|
dev_err(motg->phy.dev, "Cannot set v1p8 voltage\n");
|
|
goto disable_3p3;
|
|
}
|
|
rc = regulator_enable(motg->v1p8);
|
|
if (rc) {
|
|
dev_err(motg->phy.dev, "unable to enable the hsusb 1p8\n");
|
|
goto disable_3p3;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
regulator_disable(motg->v1p8);
|
|
disable_3p3:
|
|
regulator_disable(motg->v3p3);
|
|
exit:
|
|
return rc;
|
|
}
|
|
|
|
static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (on) {
|
|
ret = regulator_set_optimum_mode(motg->v1p8,
|
|
USB_PHY_1P8_HPM_LOAD);
|
|
if (ret < 0) {
|
|
pr_err("Could not set HPM for v1p8\n");
|
|
return ret;
|
|
}
|
|
ret = regulator_set_optimum_mode(motg->v3p3,
|
|
USB_PHY_3P3_HPM_LOAD);
|
|
if (ret < 0) {
|
|
pr_err("Could not set HPM for v3p3\n");
|
|
regulator_set_optimum_mode(motg->v1p8,
|
|
USB_PHY_1P8_LPM_LOAD);
|
|
return ret;
|
|
}
|
|
} else {
|
|
ret = regulator_set_optimum_mode(motg->v1p8,
|
|
USB_PHY_1P8_LPM_LOAD);
|
|
if (ret < 0)
|
|
pr_err("Could not set LPM for v1p8\n");
|
|
ret = regulator_set_optimum_mode(motg->v3p3,
|
|
USB_PHY_3P3_LPM_LOAD);
|
|
if (ret < 0)
|
|
pr_err("Could not set LPM for v3p3\n");
|
|
}
|
|
|
|
pr_debug("reg (%s)\n", on ? "HPM" : "LPM");
|
|
return ret < 0 ? ret : 0;
|
|
}
|
|
|
|
static int ulpi_read(struct usb_phy *phy, u32 reg)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
int cnt = 0;
|
|
|
|
/* initiate read operation */
|
|
writel(ULPI_RUN | ULPI_READ | ULPI_ADDR(reg),
|
|
USB_ULPI_VIEWPORT);
|
|
|
|
/* wait for completion */
|
|
while (cnt < ULPI_IO_TIMEOUT_USEC) {
|
|
if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
|
|
if (cnt >= ULPI_IO_TIMEOUT_USEC) {
|
|
dev_err(phy->dev, "ulpi_read: timeout %08x\n",
|
|
readl(USB_ULPI_VIEWPORT));
|
|
return -ETIMEDOUT;
|
|
}
|
|
return ULPI_DATA_READ(readl(USB_ULPI_VIEWPORT));
|
|
}
|
|
|
|
static int ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
int cnt = 0;
|
|
|
|
/* initiate write operation */
|
|
writel(ULPI_RUN | ULPI_WRITE |
|
|
ULPI_ADDR(reg) | ULPI_DATA(val),
|
|
USB_ULPI_VIEWPORT);
|
|
|
|
/* wait for completion */
|
|
while (cnt < ULPI_IO_TIMEOUT_USEC) {
|
|
if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
|
|
if (cnt >= ULPI_IO_TIMEOUT_USEC) {
|
|
dev_err(phy->dev, "ulpi_write: timeout\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static struct usb_phy_io_ops msm_otg_io_ops = {
|
|
.read = ulpi_read,
|
|
.write = ulpi_write,
|
|
};
|
|
|
|
static void ulpi_init(struct msm_otg *motg)
|
|
{
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
int *seq = pdata->phy_init_seq, idx;
|
|
u32 addr = ULPI_EXT_VENDOR_SPECIFIC;
|
|
|
|
for (idx = 0; idx < pdata->phy_init_sz; idx++) {
|
|
if (seq[idx] == -1)
|
|
continue;
|
|
|
|
dev_vdbg(motg->phy.dev, "ulpi: write 0x%02x to 0x%02x\n",
|
|
seq[idx], addr + idx);
|
|
ulpi_write(&motg->phy, seq[idx], addr + idx);
|
|
}
|
|
}
|
|
|
|
static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)
|
|
{
|
|
int ret;
|
|
|
|
if (motg->pdata->link_clk_reset)
|
|
ret = motg->pdata->link_clk_reset(motg->clk, assert);
|
|
else if (assert)
|
|
ret = reset_control_assert(motg->link_rst);
|
|
else
|
|
ret = reset_control_deassert(motg->link_rst);
|
|
|
|
if (ret)
|
|
dev_err(motg->phy.dev, "usb link clk reset %s failed\n",
|
|
assert ? "assert" : "deassert");
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int msm_otg_phy_clk_reset(struct msm_otg *motg)
|
|
{
|
|
int ret;
|
|
|
|
if (motg->pdata->phy_clk_reset)
|
|
ret = motg->pdata->phy_clk_reset(motg->phy_reset_clk);
|
|
else
|
|
ret = reset_control_reset(motg->phy_rst);
|
|
|
|
if (ret)
|
|
dev_err(motg->phy.dev, "usb phy clk reset failed\n");
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int msm_link_reset(struct msm_otg *motg)
|
|
{
|
|
u32 val;
|
|
int ret;
|
|
|
|
ret = msm_otg_link_clk_reset(motg, 1);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* wait for 1ms delay as suggested in HPG. */
|
|
usleep_range(1000, 1200);
|
|
|
|
ret = msm_otg_link_clk_reset(motg, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (motg->phy_number)
|
|
writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
|
|
|
|
/* put transceiver in serial mode as part of reset */
|
|
val = readl(USB_PORTSC) & ~PORTSC_PTS_MASK;
|
|
writel(val | PORTSC_PTS_SERIAL, USB_PORTSC);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_otg_reset(struct usb_phy *phy)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
int cnt = 0;
|
|
|
|
writel(USBCMD_RESET, USB_USBCMD);
|
|
while (cnt < LINK_RESET_TIMEOUT_USEC) {
|
|
if (!(readl(USB_USBCMD) & USBCMD_RESET))
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
if (cnt >= LINK_RESET_TIMEOUT_USEC)
|
|
return -ETIMEDOUT;
|
|
|
|
/* select ULPI phy and clear other status/control bits in PORTSC */
|
|
writel(PORTSC_PTS_ULPI, USB_PORTSC);
|
|
|
|
writel(0x0, USB_AHBBURST);
|
|
writel(0x08, USB_AHBMODE);
|
|
|
|
if (motg->phy_number)
|
|
writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
|
|
return 0;
|
|
}
|
|
|
|
static void msm_phy_reset(struct msm_otg *motg)
|
|
{
|
|
void __iomem *addr;
|
|
|
|
if (motg->pdata->phy_type != SNPS_28NM_INTEGRATED_PHY) {
|
|
msm_otg_phy_clk_reset(motg);
|
|
return;
|
|
}
|
|
|
|
addr = USB_PHY_CTRL;
|
|
if (motg->phy_number)
|
|
addr = USB_PHY_CTRL2;
|
|
|
|
/* Assert USB PHY_POR */
|
|
writel(readl(addr) | PHY_POR_ASSERT, addr);
|
|
|
|
/*
|
|
* wait for minimum 10 microseconds as suggested in HPG.
|
|
* Use a slightly larger value since the exact value didn't
|
|
* work 100% of the time.
|
|
*/
|
|
udelay(12);
|
|
|
|
/* Deassert USB PHY_POR */
|
|
writel(readl(addr) & ~PHY_POR_ASSERT, addr);
|
|
}
|
|
|
|
static int msm_usb_reset(struct usb_phy *phy)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
int ret;
|
|
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_prepare_enable(motg->core_clk);
|
|
|
|
ret = msm_link_reset(motg);
|
|
if (ret) {
|
|
dev_err(phy->dev, "phy_reset failed\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = msm_otg_reset(&motg->phy);
|
|
if (ret) {
|
|
dev_err(phy->dev, "link reset failed\n");
|
|
return ret;
|
|
}
|
|
|
|
msleep(100);
|
|
|
|
/* Reset USB PHY after performing USB Link RESET */
|
|
msm_phy_reset(motg);
|
|
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_disable_unprepare(motg->core_clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_phy_init(struct usb_phy *phy)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
u32 val, ulpi_val = 0;
|
|
|
|
/* Program USB PHY Override registers. */
|
|
ulpi_init(motg);
|
|
|
|
/*
|
|
* It is recommended in HPG to reset USB PHY after programming
|
|
* USB PHY Override registers.
|
|
*/
|
|
msm_phy_reset(motg);
|
|
|
|
if (pdata->otg_control == OTG_PHY_CONTROL) {
|
|
val = readl(USB_OTGSC);
|
|
if (pdata->mode == USB_DR_MODE_OTG) {
|
|
ulpi_val = ULPI_INT_IDGRD | ULPI_INT_SESS_VALID;
|
|
val |= OTGSC_IDIE | OTGSC_BSVIE;
|
|
} else if (pdata->mode == USB_DR_MODE_PERIPHERAL) {
|
|
ulpi_val = ULPI_INT_SESS_VALID;
|
|
val |= OTGSC_BSVIE;
|
|
}
|
|
writel(val, USB_OTGSC);
|
|
ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_RISE);
|
|
ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
|
|
}
|
|
|
|
if (motg->phy_number)
|
|
writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define PHY_SUSPEND_TIMEOUT_USEC (500 * 1000)
|
|
#define PHY_RESUME_TIMEOUT_USEC (100 * 1000)
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
#define USB_PHY_SUSP_DIG_VOL 500000
|
|
static int msm_hsusb_config_vddcx(struct msm_otg *motg, int high)
|
|
{
|
|
int max_vol = USB_PHY_VDD_DIG_VOL_MAX;
|
|
int min_vol;
|
|
int ret;
|
|
|
|
if (high)
|
|
min_vol = USB_PHY_VDD_DIG_VOL_MIN;
|
|
else
|
|
min_vol = USB_PHY_SUSP_DIG_VOL;
|
|
|
|
ret = regulator_set_voltage(motg->vddcx, min_vol, max_vol);
|
|
if (ret) {
|
|
pr_err("Cannot set vddcx voltage\n");
|
|
return ret;
|
|
}
|
|
|
|
pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int msm_otg_suspend(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
struct usb_bus *bus = phy->otg->host;
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
void __iomem *addr;
|
|
int cnt = 0;
|
|
|
|
if (atomic_read(&motg->in_lpm))
|
|
return 0;
|
|
|
|
disable_irq(motg->irq);
|
|
/*
|
|
* Chipidea 45-nm PHY suspend sequence:
|
|
*
|
|
* Interrupt Latch Register auto-clear feature is not present
|
|
* in all PHY versions. Latch register is clear on read type.
|
|
* Clear latch register to avoid spurious wakeup from
|
|
* low power mode (LPM).
|
|
*
|
|
* PHY comparators are disabled when PHY enters into low power
|
|
* mode (LPM). Keep PHY comparators ON in LPM only when we expect
|
|
* VBUS/Id notifications from USB PHY. Otherwise turn off USB
|
|
* PHY comparators. This save significant amount of power.
|
|
*
|
|
* PLL is not turned off when PHY enters into low power mode (LPM).
|
|
* Disable PLL for maximum power savings.
|
|
*/
|
|
|
|
if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY) {
|
|
ulpi_read(phy, 0x14);
|
|
if (pdata->otg_control == OTG_PHY_CONTROL)
|
|
ulpi_write(phy, 0x01, 0x30);
|
|
ulpi_write(phy, 0x08, 0x09);
|
|
}
|
|
|
|
/*
|
|
* PHY may take some time or even fail to enter into low power
|
|
* mode (LPM). Hence poll for 500 msec and reset the PHY and link
|
|
* in failure case.
|
|
*/
|
|
writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
|
|
while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
|
|
if (readl(USB_PORTSC) & PORTSC_PHCD)
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
|
|
if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) {
|
|
dev_err(phy->dev, "Unable to suspend PHY\n");
|
|
msm_otg_reset(phy);
|
|
enable_irq(motg->irq);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
/*
|
|
* PHY has capability to generate interrupt asynchronously in low
|
|
* power mode (LPM). This interrupt is level triggered. So USB IRQ
|
|
* line must be disabled till async interrupt enable bit is cleared
|
|
* in USBCMD register. Assert STP (ULPI interface STOP signal) to
|
|
* block data communication from PHY.
|
|
*/
|
|
writel(readl(USB_USBCMD) | ASYNC_INTR_CTRL | ULPI_STP_CTRL, USB_USBCMD);
|
|
|
|
addr = USB_PHY_CTRL;
|
|
if (motg->phy_number)
|
|
addr = USB_PHY_CTRL2;
|
|
|
|
if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
|
|
motg->pdata->otg_control == OTG_PMIC_CONTROL)
|
|
writel(readl(addr) | PHY_RETEN, addr);
|
|
|
|
clk_disable_unprepare(motg->pclk);
|
|
clk_disable_unprepare(motg->clk);
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_disable_unprepare(motg->core_clk);
|
|
|
|
if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
|
|
motg->pdata->otg_control == OTG_PMIC_CONTROL) {
|
|
msm_hsusb_ldo_set_mode(motg, 0);
|
|
msm_hsusb_config_vddcx(motg, 0);
|
|
}
|
|
|
|
if (device_may_wakeup(phy->dev))
|
|
enable_irq_wake(motg->irq);
|
|
if (bus)
|
|
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
|
|
|
|
atomic_set(&motg->in_lpm, 1);
|
|
enable_irq(motg->irq);
|
|
|
|
dev_info(phy->dev, "USB in low power mode\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_otg_resume(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
struct usb_bus *bus = phy->otg->host;
|
|
void __iomem *addr;
|
|
int cnt = 0;
|
|
unsigned temp;
|
|
|
|
if (!atomic_read(&motg->in_lpm))
|
|
return 0;
|
|
|
|
clk_prepare_enable(motg->pclk);
|
|
clk_prepare_enable(motg->clk);
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_prepare_enable(motg->core_clk);
|
|
|
|
if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
|
|
motg->pdata->otg_control == OTG_PMIC_CONTROL) {
|
|
|
|
addr = USB_PHY_CTRL;
|
|
if (motg->phy_number)
|
|
addr = USB_PHY_CTRL2;
|
|
|
|
msm_hsusb_ldo_set_mode(motg, 1);
|
|
msm_hsusb_config_vddcx(motg, 1);
|
|
writel(readl(addr) & ~PHY_RETEN, addr);
|
|
}
|
|
|
|
temp = readl(USB_USBCMD);
|
|
temp &= ~ASYNC_INTR_CTRL;
|
|
temp &= ~ULPI_STP_CTRL;
|
|
writel(temp, USB_USBCMD);
|
|
|
|
/*
|
|
* PHY comes out of low power mode (LPM) in case of wakeup
|
|
* from asynchronous interrupt.
|
|
*/
|
|
if (!(readl(USB_PORTSC) & PORTSC_PHCD))
|
|
goto skip_phy_resume;
|
|
|
|
writel(readl(USB_PORTSC) & ~PORTSC_PHCD, USB_PORTSC);
|
|
while (cnt < PHY_RESUME_TIMEOUT_USEC) {
|
|
if (!(readl(USB_PORTSC) & PORTSC_PHCD))
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
|
|
if (cnt >= PHY_RESUME_TIMEOUT_USEC) {
|
|
/*
|
|
* This is a fatal error. Reset the link and
|
|
* PHY. USB state can not be restored. Re-insertion
|
|
* of USB cable is the only way to get USB working.
|
|
*/
|
|
dev_err(phy->dev, "Unable to resume USB. Re-plugin the cable\n");
|
|
msm_otg_reset(phy);
|
|
}
|
|
|
|
skip_phy_resume:
|
|
if (device_may_wakeup(phy->dev))
|
|
disable_irq_wake(motg->irq);
|
|
if (bus)
|
|
set_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
|
|
|
|
atomic_set(&motg->in_lpm, 0);
|
|
|
|
if (motg->async_int) {
|
|
motg->async_int = 0;
|
|
pm_runtime_put(phy->dev);
|
|
enable_irq(motg->irq);
|
|
}
|
|
|
|
dev_info(phy->dev, "USB exited from low power mode\n");
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static void msm_otg_notify_charger(struct msm_otg *motg, unsigned mA)
|
|
{
|
|
if (motg->cur_power == mA)
|
|
return;
|
|
|
|
/* TODO: Notify PMIC about available current */
|
|
dev_info(motg->phy.dev, "Avail curr from USB = %u\n", mA);
|
|
motg->cur_power = mA;
|
|
}
|
|
|
|
static int msm_otg_set_power(struct usb_phy *phy, unsigned mA)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
|
|
/*
|
|
* Gadget driver uses set_power method to notify about the
|
|
* available current based on suspend/configured states.
|
|
*
|
|
* IDEV_CHG can be drawn irrespective of suspend/un-configured
|
|
* states when CDP/ACA is connected.
|
|
*/
|
|
if (motg->chg_type == USB_SDP_CHARGER)
|
|
msm_otg_notify_charger(motg, mA);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void msm_otg_start_host(struct usb_phy *phy, int on)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
struct usb_hcd *hcd;
|
|
|
|
if (!phy->otg->host)
|
|
return;
|
|
|
|
hcd = bus_to_hcd(phy->otg->host);
|
|
|
|
if (on) {
|
|
dev_dbg(phy->dev, "host on\n");
|
|
|
|
if (pdata->vbus_power)
|
|
pdata->vbus_power(1);
|
|
/*
|
|
* Some boards have a switch cotrolled by gpio
|
|
* to enable/disable internal HUB. Enable internal
|
|
* HUB before kicking the host.
|
|
*/
|
|
if (pdata->setup_gpio)
|
|
pdata->setup_gpio(OTG_STATE_A_HOST);
|
|
#ifdef CONFIG_USB
|
|
usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
|
|
device_wakeup_enable(hcd->self.controller);
|
|
#endif
|
|
} else {
|
|
dev_dbg(phy->dev, "host off\n");
|
|
|
|
#ifdef CONFIG_USB
|
|
usb_remove_hcd(hcd);
|
|
#endif
|
|
if (pdata->setup_gpio)
|
|
pdata->setup_gpio(OTG_STATE_UNDEFINED);
|
|
if (pdata->vbus_power)
|
|
pdata->vbus_power(0);
|
|
}
|
|
}
|
|
|
|
static int msm_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
|
|
{
|
|
struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
|
|
struct usb_hcd *hcd;
|
|
|
|
/*
|
|
* Fail host registration if this board can support
|
|
* only peripheral configuration.
|
|
*/
|
|
if (motg->pdata->mode == USB_DR_MODE_PERIPHERAL) {
|
|
dev_info(otg->phy->dev, "Host mode is not supported\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (!host) {
|
|
if (otg->phy->state == OTG_STATE_A_HOST) {
|
|
pm_runtime_get_sync(otg->phy->dev);
|
|
msm_otg_start_host(otg->phy, 0);
|
|
otg->host = NULL;
|
|
otg->phy->state = OTG_STATE_UNDEFINED;
|
|
schedule_work(&motg->sm_work);
|
|
} else {
|
|
otg->host = NULL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
hcd = bus_to_hcd(host);
|
|
hcd->power_budget = motg->pdata->power_budget;
|
|
|
|
otg->host = host;
|
|
dev_dbg(otg->phy->dev, "host driver registered w/ tranceiver\n");
|
|
|
|
/*
|
|
* Kick the state machine work, if peripheral is not supported
|
|
* or peripheral is already registered with us.
|
|
*/
|
|
if (motg->pdata->mode == USB_DR_MODE_HOST || otg->gadget) {
|
|
pm_runtime_get_sync(otg->phy->dev);
|
|
schedule_work(&motg->sm_work);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void msm_otg_start_peripheral(struct usb_phy *phy, int on)
|
|
{
|
|
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
|
|
if (!phy->otg->gadget)
|
|
return;
|
|
|
|
if (on) {
|
|
dev_dbg(phy->dev, "gadget on\n");
|
|
/*
|
|
* Some boards have a switch cotrolled by gpio
|
|
* to enable/disable internal HUB. Disable internal
|
|
* HUB before kicking the gadget.
|
|
*/
|
|
if (pdata->setup_gpio)
|
|
pdata->setup_gpio(OTG_STATE_B_PERIPHERAL);
|
|
usb_gadget_vbus_connect(phy->otg->gadget);
|
|
} else {
|
|
dev_dbg(phy->dev, "gadget off\n");
|
|
usb_gadget_vbus_disconnect(phy->otg->gadget);
|
|
if (pdata->setup_gpio)
|
|
pdata->setup_gpio(OTG_STATE_UNDEFINED);
|
|
}
|
|
|
|
}
|
|
|
|
static int msm_otg_set_peripheral(struct usb_otg *otg,
|
|
struct usb_gadget *gadget)
|
|
{
|
|
struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
|
|
|
|
/*
|
|
* Fail peripheral registration if this board can support
|
|
* only host configuration.
|
|
*/
|
|
if (motg->pdata->mode == USB_DR_MODE_HOST) {
|
|
dev_info(otg->phy->dev, "Peripheral mode is not supported\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (!gadget) {
|
|
if (otg->phy->state == OTG_STATE_B_PERIPHERAL) {
|
|
pm_runtime_get_sync(otg->phy->dev);
|
|
msm_otg_start_peripheral(otg->phy, 0);
|
|
otg->gadget = NULL;
|
|
otg->phy->state = OTG_STATE_UNDEFINED;
|
|
schedule_work(&motg->sm_work);
|
|
} else {
|
|
otg->gadget = NULL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
otg->gadget = gadget;
|
|
dev_dbg(otg->phy->dev, "peripheral driver registered w/ tranceiver\n");
|
|
|
|
/*
|
|
* Kick the state machine work, if host is not supported
|
|
* or host is already registered with us.
|
|
*/
|
|
if (motg->pdata->mode == USB_DR_MODE_PERIPHERAL || otg->host) {
|
|
pm_runtime_get_sync(otg->phy->dev);
|
|
schedule_work(&motg->sm_work);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static bool msm_chg_check_secondary_det(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
bool ret = false;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
ret = chg_det & (1 << 4);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x87);
|
|
ret = chg_det & 1;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static void msm_chg_enable_secondary_det(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
/* Turn off charger block */
|
|
chg_det |= ~(1 << 1);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
udelay(20);
|
|
/* control chg block via ULPI */
|
|
chg_det &= ~(1 << 3);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
/* put it in host mode for enabling D- source */
|
|
chg_det &= ~(1 << 2);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
/* Turn on chg detect block */
|
|
chg_det &= ~(1 << 1);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
udelay(20);
|
|
/* enable chg detection */
|
|
chg_det &= ~(1 << 0);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
/*
|
|
* Configure DM as current source, DP as current sink
|
|
* and enable battery charging comparators.
|
|
*/
|
|
ulpi_write(phy, 0x8, 0x85);
|
|
ulpi_write(phy, 0x2, 0x85);
|
|
ulpi_write(phy, 0x1, 0x85);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static bool msm_chg_check_primary_det(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
bool ret = false;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
ret = chg_det & (1 << 4);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x87);
|
|
ret = chg_det & 1;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static void msm_chg_enable_primary_det(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
/* enable chg detection */
|
|
chg_det &= ~(1 << 0);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
/*
|
|
* Configure DP as current source, DM as current sink
|
|
* and enable battery charging comparators.
|
|
*/
|
|
ulpi_write(phy, 0x2, 0x85);
|
|
ulpi_write(phy, 0x1, 0x85);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static bool msm_chg_check_dcd(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 line_state;
|
|
bool ret = false;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
line_state = ulpi_read(phy, 0x15);
|
|
ret = !(line_state & 1);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
line_state = ulpi_read(phy, 0x87);
|
|
ret = line_state & 2;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static void msm_chg_disable_dcd(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
chg_det &= ~(1 << 5);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
ulpi_write(phy, 0x10, 0x86);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void msm_chg_enable_dcd(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 chg_det;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
/* Turn on D+ current source */
|
|
chg_det |= (1 << 5);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
/* Data contact detection enable */
|
|
ulpi_write(phy, 0x10, 0x85);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void msm_chg_block_on(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 func_ctrl, chg_det;
|
|
|
|
/* put the controller in non-driving mode */
|
|
func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
|
|
func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
|
|
func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
|
|
ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
/* control chg block via ULPI */
|
|
chg_det &= ~(1 << 3);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
/* Turn on chg detect block */
|
|
chg_det &= ~(1 << 1);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
udelay(20);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
/* Clear charger detecting control bits */
|
|
ulpi_write(phy, 0x3F, 0x86);
|
|
/* Clear alt interrupt latch and enable bits */
|
|
ulpi_write(phy, 0x1F, 0x92);
|
|
ulpi_write(phy, 0x1F, 0x95);
|
|
udelay(100);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void msm_chg_block_off(struct msm_otg *motg)
|
|
{
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 func_ctrl, chg_det;
|
|
|
|
switch (motg->pdata->phy_type) {
|
|
case CI_45NM_INTEGRATED_PHY:
|
|
chg_det = ulpi_read(phy, 0x34);
|
|
/* Turn off charger block */
|
|
chg_det |= ~(1 << 1);
|
|
ulpi_write(phy, chg_det, 0x34);
|
|
break;
|
|
case SNPS_28NM_INTEGRATED_PHY:
|
|
/* Clear charger detecting control bits */
|
|
ulpi_write(phy, 0x3F, 0x86);
|
|
/* Clear alt interrupt latch and enable bits */
|
|
ulpi_write(phy, 0x1F, 0x92);
|
|
ulpi_write(phy, 0x1F, 0x95);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
/* put the controller in normal mode */
|
|
func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
|
|
func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
|
|
func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
|
|
ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
|
|
}
|
|
|
|
#define MSM_CHG_DCD_POLL_TIME (100 * HZ/1000) /* 100 msec */
|
|
#define MSM_CHG_DCD_MAX_RETRIES 6 /* Tdcd_tmout = 6 * 100 msec */
|
|
#define MSM_CHG_PRIMARY_DET_TIME (40 * HZ/1000) /* TVDPSRC_ON */
|
|
#define MSM_CHG_SECONDARY_DET_TIME (40 * HZ/1000) /* TVDMSRC_ON */
|
|
static void msm_chg_detect_work(struct work_struct *w)
|
|
{
|
|
struct msm_otg *motg = container_of(w, struct msm_otg, chg_work.work);
|
|
struct usb_phy *phy = &motg->phy;
|
|
bool is_dcd, tmout, vout;
|
|
unsigned long delay;
|
|
|
|
dev_dbg(phy->dev, "chg detection work\n");
|
|
switch (motg->chg_state) {
|
|
case USB_CHG_STATE_UNDEFINED:
|
|
pm_runtime_get_sync(phy->dev);
|
|
msm_chg_block_on(motg);
|
|
msm_chg_enable_dcd(motg);
|
|
motg->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
|
|
motg->dcd_retries = 0;
|
|
delay = MSM_CHG_DCD_POLL_TIME;
|
|
break;
|
|
case USB_CHG_STATE_WAIT_FOR_DCD:
|
|
is_dcd = msm_chg_check_dcd(motg);
|
|
tmout = ++motg->dcd_retries == MSM_CHG_DCD_MAX_RETRIES;
|
|
if (is_dcd || tmout) {
|
|
msm_chg_disable_dcd(motg);
|
|
msm_chg_enable_primary_det(motg);
|
|
delay = MSM_CHG_PRIMARY_DET_TIME;
|
|
motg->chg_state = USB_CHG_STATE_DCD_DONE;
|
|
} else {
|
|
delay = MSM_CHG_DCD_POLL_TIME;
|
|
}
|
|
break;
|
|
case USB_CHG_STATE_DCD_DONE:
|
|
vout = msm_chg_check_primary_det(motg);
|
|
if (vout) {
|
|
msm_chg_enable_secondary_det(motg);
|
|
delay = MSM_CHG_SECONDARY_DET_TIME;
|
|
motg->chg_state = USB_CHG_STATE_PRIMARY_DONE;
|
|
} else {
|
|
motg->chg_type = USB_SDP_CHARGER;
|
|
motg->chg_state = USB_CHG_STATE_DETECTED;
|
|
delay = 0;
|
|
}
|
|
break;
|
|
case USB_CHG_STATE_PRIMARY_DONE:
|
|
vout = msm_chg_check_secondary_det(motg);
|
|
if (vout)
|
|
motg->chg_type = USB_DCP_CHARGER;
|
|
else
|
|
motg->chg_type = USB_CDP_CHARGER;
|
|
motg->chg_state = USB_CHG_STATE_SECONDARY_DONE;
|
|
/* fall through */
|
|
case USB_CHG_STATE_SECONDARY_DONE:
|
|
motg->chg_state = USB_CHG_STATE_DETECTED;
|
|
case USB_CHG_STATE_DETECTED:
|
|
msm_chg_block_off(motg);
|
|
dev_dbg(phy->dev, "charger = %d\n", motg->chg_type);
|
|
schedule_work(&motg->sm_work);
|
|
return;
|
|
default:
|
|
return;
|
|
}
|
|
|
|
schedule_delayed_work(&motg->chg_work, delay);
|
|
}
|
|
|
|
/*
|
|
* We support OTG, Peripheral only and Host only configurations. In case
|
|
* of OTG, mode switch (host-->peripheral/peripheral-->host) can happen
|
|
* via Id pin status or user request (debugfs). Id/BSV interrupts are not
|
|
* enabled when switch is controlled by user and default mode is supplied
|
|
* by board file, which can be changed by userspace later.
|
|
*/
|
|
static void msm_otg_init_sm(struct msm_otg *motg)
|
|
{
|
|
struct msm_otg_platform_data *pdata = motg->pdata;
|
|
u32 otgsc = readl(USB_OTGSC);
|
|
|
|
switch (pdata->mode) {
|
|
case USB_DR_MODE_OTG:
|
|
if (pdata->otg_control == OTG_PHY_CONTROL) {
|
|
if (otgsc & OTGSC_ID)
|
|
set_bit(ID, &motg->inputs);
|
|
else
|
|
clear_bit(ID, &motg->inputs);
|
|
|
|
if (otgsc & OTGSC_BSV)
|
|
set_bit(B_SESS_VLD, &motg->inputs);
|
|
else
|
|
clear_bit(B_SESS_VLD, &motg->inputs);
|
|
} else if (pdata->otg_control == OTG_USER_CONTROL) {
|
|
set_bit(ID, &motg->inputs);
|
|
clear_bit(B_SESS_VLD, &motg->inputs);
|
|
}
|
|
break;
|
|
case USB_DR_MODE_HOST:
|
|
clear_bit(ID, &motg->inputs);
|
|
break;
|
|
case USB_DR_MODE_PERIPHERAL:
|
|
set_bit(ID, &motg->inputs);
|
|
if (otgsc & OTGSC_BSV)
|
|
set_bit(B_SESS_VLD, &motg->inputs);
|
|
else
|
|
clear_bit(B_SESS_VLD, &motg->inputs);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void msm_otg_sm_work(struct work_struct *w)
|
|
{
|
|
struct msm_otg *motg = container_of(w, struct msm_otg, sm_work);
|
|
struct usb_otg *otg = motg->phy.otg;
|
|
|
|
switch (otg->phy->state) {
|
|
case OTG_STATE_UNDEFINED:
|
|
dev_dbg(otg->phy->dev, "OTG_STATE_UNDEFINED state\n");
|
|
msm_otg_reset(otg->phy);
|
|
msm_otg_init_sm(motg);
|
|
otg->phy->state = OTG_STATE_B_IDLE;
|
|
/* FALL THROUGH */
|
|
case OTG_STATE_B_IDLE:
|
|
dev_dbg(otg->phy->dev, "OTG_STATE_B_IDLE state\n");
|
|
if (!test_bit(ID, &motg->inputs) && otg->host) {
|
|
/* disable BSV bit */
|
|
writel(readl(USB_OTGSC) & ~OTGSC_BSVIE, USB_OTGSC);
|
|
msm_otg_start_host(otg->phy, 1);
|
|
otg->phy->state = OTG_STATE_A_HOST;
|
|
} else if (test_bit(B_SESS_VLD, &motg->inputs)) {
|
|
switch (motg->chg_state) {
|
|
case USB_CHG_STATE_UNDEFINED:
|
|
msm_chg_detect_work(&motg->chg_work.work);
|
|
break;
|
|
case USB_CHG_STATE_DETECTED:
|
|
switch (motg->chg_type) {
|
|
case USB_DCP_CHARGER:
|
|
msm_otg_notify_charger(motg,
|
|
IDEV_CHG_MAX);
|
|
break;
|
|
case USB_CDP_CHARGER:
|
|
msm_otg_notify_charger(motg,
|
|
IDEV_CHG_MAX);
|
|
msm_otg_start_peripheral(otg->phy, 1);
|
|
otg->phy->state
|
|
= OTG_STATE_B_PERIPHERAL;
|
|
break;
|
|
case USB_SDP_CHARGER:
|
|
msm_otg_notify_charger(motg, IUNIT);
|
|
msm_otg_start_peripheral(otg->phy, 1);
|
|
otg->phy->state
|
|
= OTG_STATE_B_PERIPHERAL;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
} else {
|
|
/*
|
|
* If charger detection work is pending, decrement
|
|
* the pm usage counter to balance with the one that
|
|
* is incremented in charger detection work.
|
|
*/
|
|
if (cancel_delayed_work_sync(&motg->chg_work)) {
|
|
pm_runtime_put_sync(otg->phy->dev);
|
|
msm_otg_reset(otg->phy);
|
|
}
|
|
msm_otg_notify_charger(motg, 0);
|
|
motg->chg_state = USB_CHG_STATE_UNDEFINED;
|
|
motg->chg_type = USB_INVALID_CHARGER;
|
|
}
|
|
pm_runtime_put_sync(otg->phy->dev);
|
|
break;
|
|
case OTG_STATE_B_PERIPHERAL:
|
|
dev_dbg(otg->phy->dev, "OTG_STATE_B_PERIPHERAL state\n");
|
|
if (!test_bit(B_SESS_VLD, &motg->inputs) ||
|
|
!test_bit(ID, &motg->inputs)) {
|
|
msm_otg_notify_charger(motg, 0);
|
|
msm_otg_start_peripheral(otg->phy, 0);
|
|
motg->chg_state = USB_CHG_STATE_UNDEFINED;
|
|
motg->chg_type = USB_INVALID_CHARGER;
|
|
otg->phy->state = OTG_STATE_B_IDLE;
|
|
msm_otg_reset(otg->phy);
|
|
schedule_work(w);
|
|
}
|
|
break;
|
|
case OTG_STATE_A_HOST:
|
|
dev_dbg(otg->phy->dev, "OTG_STATE_A_HOST state\n");
|
|
if (test_bit(ID, &motg->inputs)) {
|
|
msm_otg_start_host(otg->phy, 0);
|
|
otg->phy->state = OTG_STATE_B_IDLE;
|
|
msm_otg_reset(otg->phy);
|
|
schedule_work(w);
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static irqreturn_t msm_otg_irq(int irq, void *data)
|
|
{
|
|
struct msm_otg *motg = data;
|
|
struct usb_phy *phy = &motg->phy;
|
|
u32 otgsc = 0;
|
|
|
|
if (atomic_read(&motg->in_lpm)) {
|
|
disable_irq_nosync(irq);
|
|
motg->async_int = 1;
|
|
pm_runtime_get(phy->dev);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
otgsc = readl(USB_OTGSC);
|
|
if (!(otgsc & (OTGSC_IDIS | OTGSC_BSVIS)))
|
|
return IRQ_NONE;
|
|
|
|
if ((otgsc & OTGSC_IDIS) && (otgsc & OTGSC_IDIE)) {
|
|
if (otgsc & OTGSC_ID)
|
|
set_bit(ID, &motg->inputs);
|
|
else
|
|
clear_bit(ID, &motg->inputs);
|
|
dev_dbg(phy->dev, "ID set/clear\n");
|
|
pm_runtime_get_noresume(phy->dev);
|
|
} else if ((otgsc & OTGSC_BSVIS) && (otgsc & OTGSC_BSVIE)) {
|
|
if (otgsc & OTGSC_BSV)
|
|
set_bit(B_SESS_VLD, &motg->inputs);
|
|
else
|
|
clear_bit(B_SESS_VLD, &motg->inputs);
|
|
dev_dbg(phy->dev, "BSV set/clear\n");
|
|
pm_runtime_get_noresume(phy->dev);
|
|
}
|
|
|
|
writel(otgsc, USB_OTGSC);
|
|
schedule_work(&motg->sm_work);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int msm_otg_mode_show(struct seq_file *s, void *unused)
|
|
{
|
|
struct msm_otg *motg = s->private;
|
|
struct usb_otg *otg = motg->phy.otg;
|
|
|
|
switch (otg->phy->state) {
|
|
case OTG_STATE_A_HOST:
|
|
seq_puts(s, "host\n");
|
|
break;
|
|
case OTG_STATE_B_PERIPHERAL:
|
|
seq_puts(s, "peripheral\n");
|
|
break;
|
|
default:
|
|
seq_puts(s, "none\n");
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_otg_mode_open(struct inode *inode, struct file *file)
|
|
{
|
|
return single_open(file, msm_otg_mode_show, inode->i_private);
|
|
}
|
|
|
|
static ssize_t msm_otg_mode_write(struct file *file, const char __user *ubuf,
|
|
size_t count, loff_t *ppos)
|
|
{
|
|
struct seq_file *s = file->private_data;
|
|
struct msm_otg *motg = s->private;
|
|
char buf[16];
|
|
struct usb_otg *otg = motg->phy.otg;
|
|
int status = count;
|
|
enum usb_dr_mode req_mode;
|
|
|
|
memset(buf, 0x00, sizeof(buf));
|
|
|
|
if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count))) {
|
|
status = -EFAULT;
|
|
goto out;
|
|
}
|
|
|
|
if (!strncmp(buf, "host", 4)) {
|
|
req_mode = USB_DR_MODE_HOST;
|
|
} else if (!strncmp(buf, "peripheral", 10)) {
|
|
req_mode = USB_DR_MODE_PERIPHERAL;
|
|
} else if (!strncmp(buf, "none", 4)) {
|
|
req_mode = USB_DR_MODE_UNKNOWN;
|
|
} else {
|
|
status = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
switch (req_mode) {
|
|
case USB_DR_MODE_UNKNOWN:
|
|
switch (otg->phy->state) {
|
|
case OTG_STATE_A_HOST:
|
|
case OTG_STATE_B_PERIPHERAL:
|
|
set_bit(ID, &motg->inputs);
|
|
clear_bit(B_SESS_VLD, &motg->inputs);
|
|
break;
|
|
default:
|
|
goto out;
|
|
}
|
|
break;
|
|
case USB_DR_MODE_PERIPHERAL:
|
|
switch (otg->phy->state) {
|
|
case OTG_STATE_B_IDLE:
|
|
case OTG_STATE_A_HOST:
|
|
set_bit(ID, &motg->inputs);
|
|
set_bit(B_SESS_VLD, &motg->inputs);
|
|
break;
|
|
default:
|
|
goto out;
|
|
}
|
|
break;
|
|
case USB_DR_MODE_HOST:
|
|
switch (otg->phy->state) {
|
|
case OTG_STATE_B_IDLE:
|
|
case OTG_STATE_B_PERIPHERAL:
|
|
clear_bit(ID, &motg->inputs);
|
|
break;
|
|
default:
|
|
goto out;
|
|
}
|
|
break;
|
|
default:
|
|
goto out;
|
|
}
|
|
|
|
pm_runtime_get_sync(otg->phy->dev);
|
|
schedule_work(&motg->sm_work);
|
|
out:
|
|
return status;
|
|
}
|
|
|
|
const struct file_operations msm_otg_mode_fops = {
|
|
.open = msm_otg_mode_open,
|
|
.read = seq_read,
|
|
.write = msm_otg_mode_write,
|
|
.llseek = seq_lseek,
|
|
.release = single_release,
|
|
};
|
|
|
|
static struct dentry *msm_otg_dbg_root;
|
|
static struct dentry *msm_otg_dbg_mode;
|
|
|
|
static int msm_otg_debugfs_init(struct msm_otg *motg)
|
|
{
|
|
msm_otg_dbg_root = debugfs_create_dir("msm_otg", NULL);
|
|
|
|
if (!msm_otg_dbg_root || IS_ERR(msm_otg_dbg_root))
|
|
return -ENODEV;
|
|
|
|
msm_otg_dbg_mode = debugfs_create_file("mode", S_IRUGO | S_IWUSR,
|
|
msm_otg_dbg_root, motg, &msm_otg_mode_fops);
|
|
if (!msm_otg_dbg_mode) {
|
|
debugfs_remove(msm_otg_dbg_root);
|
|
msm_otg_dbg_root = NULL;
|
|
return -ENODEV;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void msm_otg_debugfs_cleanup(void)
|
|
{
|
|
debugfs_remove(msm_otg_dbg_mode);
|
|
debugfs_remove(msm_otg_dbg_root);
|
|
}
|
|
|
|
static struct of_device_id msm_otg_dt_match[] = {
|
|
{
|
|
.compatible = "qcom,usb-otg-ci",
|
|
.data = (void *) CI_45NM_INTEGRATED_PHY
|
|
},
|
|
{
|
|
.compatible = "qcom,usb-otg-snps",
|
|
.data = (void *) SNPS_28NM_INTEGRATED_PHY
|
|
},
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, msm_otg_dt_match);
|
|
|
|
static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
|
|
{
|
|
struct msm_otg_platform_data *pdata;
|
|
const struct of_device_id *id;
|
|
struct device_node *node = pdev->dev.of_node;
|
|
struct property *prop;
|
|
int len, ret, words;
|
|
u32 val;
|
|
|
|
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
|
|
if (!pdata)
|
|
return -ENOMEM;
|
|
|
|
motg->pdata = pdata;
|
|
|
|
id = of_match_device(msm_otg_dt_match, &pdev->dev);
|
|
pdata->phy_type = (int) id->data;
|
|
|
|
motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
|
|
if (IS_ERR(motg->link_rst))
|
|
return PTR_ERR(motg->link_rst);
|
|
|
|
motg->phy_rst = devm_reset_control_get(&pdev->dev, "phy");
|
|
if (IS_ERR(motg->phy_rst))
|
|
return PTR_ERR(motg->phy_rst);
|
|
|
|
pdata->mode = of_usb_get_dr_mode(node);
|
|
if (pdata->mode == USB_DR_MODE_UNKNOWN)
|
|
pdata->mode = USB_DR_MODE_OTG;
|
|
|
|
pdata->otg_control = OTG_PHY_CONTROL;
|
|
if (!of_property_read_u32(node, "qcom,otg-control", &val))
|
|
if (val == OTG_PMIC_CONTROL)
|
|
pdata->otg_control = val;
|
|
|
|
if (!of_property_read_u32(node, "qcom,phy-num", &val) && val < 2)
|
|
motg->phy_number = val;
|
|
|
|
prop = of_find_property(node, "qcom,phy-init-sequence", &len);
|
|
if (!prop || !len)
|
|
return 0;
|
|
|
|
words = len / sizeof(u32);
|
|
|
|
if (words >= ULPI_EXT_VENDOR_SPECIFIC) {
|
|
dev_warn(&pdev->dev, "Too big PHY init sequence %d\n", words);
|
|
return 0;
|
|
}
|
|
|
|
pdata->phy_init_seq = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
|
|
if (!pdata->phy_init_seq) {
|
|
dev_warn(&pdev->dev, "No space for PHY init sequence\n");
|
|
return 0;
|
|
}
|
|
|
|
ret = of_property_read_u32_array(node, "qcom,phy-init-sequence",
|
|
pdata->phy_init_seq, words);
|
|
if (!ret)
|
|
pdata->phy_init_sz = words;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_otg_probe(struct platform_device *pdev)
|
|
{
|
|
struct regulator_bulk_data regs[3];
|
|
int ret = 0;
|
|
struct device_node *np = pdev->dev.of_node;
|
|
struct msm_otg_platform_data *pdata;
|
|
struct resource *res;
|
|
struct msm_otg *motg;
|
|
struct usb_phy *phy;
|
|
void __iomem *phy_select;
|
|
|
|
motg = devm_kzalloc(&pdev->dev, sizeof(struct msm_otg), GFP_KERNEL);
|
|
if (!motg) {
|
|
dev_err(&pdev->dev, "unable to allocate msm_otg\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
pdata = dev_get_platdata(&pdev->dev);
|
|
if (!pdata) {
|
|
if (!np)
|
|
return -ENXIO;
|
|
ret = msm_otg_read_dt(pdev, motg);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
|
|
GFP_KERNEL);
|
|
if (!motg->phy.otg) {
|
|
dev_err(&pdev->dev, "unable to allocate msm_otg\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
phy = &motg->phy;
|
|
phy->dev = &pdev->dev;
|
|
|
|
motg->phy_reset_clk = devm_clk_get(&pdev->dev,
|
|
np ? "phy" : "usb_phy_clk");
|
|
if (IS_ERR(motg->phy_reset_clk)) {
|
|
dev_err(&pdev->dev, "failed to get usb_phy_clk\n");
|
|
return PTR_ERR(motg->phy_reset_clk);
|
|
}
|
|
|
|
motg->clk = devm_clk_get(&pdev->dev, np ? "core" : "usb_hs_clk");
|
|
if (IS_ERR(motg->clk)) {
|
|
dev_err(&pdev->dev, "failed to get usb_hs_clk\n");
|
|
return PTR_ERR(motg->clk);
|
|
}
|
|
|
|
/*
|
|
* If USB Core is running its protocol engine based on CORE CLK,
|
|
* CORE CLK must be running at >55Mhz for correct HSUSB
|
|
* operation and USB core cannot tolerate frequency changes on
|
|
* CORE CLK.
|
|
*/
|
|
motg->pclk = devm_clk_get(&pdev->dev, np ? "iface" : "usb_hs_pclk");
|
|
if (IS_ERR(motg->pclk)) {
|
|
dev_err(&pdev->dev, "failed to get usb_hs_pclk\n");
|
|
return PTR_ERR(motg->pclk);
|
|
}
|
|
|
|
/*
|
|
* USB core clock is not present on all MSM chips. This
|
|
* clock is introduced to remove the dependency on AXI
|
|
* bus frequency.
|
|
*/
|
|
motg->core_clk = devm_clk_get(&pdev->dev,
|
|
np ? "alt_core" : "usb_hs_core_clk");
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
motg->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
|
|
if (IS_ERR(motg->regs))
|
|
return PTR_ERR(motg->regs);
|
|
|
|
/*
|
|
* NOTE: The PHYs can be multiplexed between the chipidea controller
|
|
* and the dwc3 controller, using a single bit. It is important that
|
|
* the dwc3 driver does not set this bit in an incompatible way.
|
|
*/
|
|
if (motg->phy_number) {
|
|
phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
|
|
if (IS_ERR(phy_select))
|
|
return PTR_ERR(phy_select);
|
|
/* Enable second PHY with the OTG port */
|
|
writel_relaxed(0x1, phy_select);
|
|
}
|
|
|
|
dev_info(&pdev->dev, "OTG regs = %p\n", motg->regs);
|
|
|
|
motg->irq = platform_get_irq(pdev, 0);
|
|
if (motg->irq < 0) {
|
|
dev_err(&pdev->dev, "platform_get_irq failed\n");
|
|
return motg->irq;
|
|
}
|
|
|
|
regs[0].supply = "vddcx";
|
|
regs[1].supply = "v3p3";
|
|
regs[2].supply = "v1p8";
|
|
|
|
ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(regs), regs);
|
|
if (ret)
|
|
return ret;
|
|
|
|
motg->vddcx = regs[0].consumer;
|
|
motg->v3p3 = regs[1].consumer;
|
|
motg->v1p8 = regs[2].consumer;
|
|
|
|
clk_set_rate(motg->clk, 60000000);
|
|
|
|
clk_prepare_enable(motg->clk);
|
|
clk_prepare_enable(motg->pclk);
|
|
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_prepare_enable(motg->core_clk);
|
|
|
|
ret = msm_hsusb_init_vddcx(motg, 1);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "hsusb vddcx configuration failed\n");
|
|
goto disable_clks;
|
|
}
|
|
|
|
ret = msm_hsusb_ldo_init(motg, 1);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "hsusb vreg configuration failed\n");
|
|
goto disable_vddcx;
|
|
}
|
|
ret = msm_hsusb_ldo_set_mode(motg, 1);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "hsusb vreg enable failed\n");
|
|
goto disable_ldo;
|
|
}
|
|
|
|
writel(0, USB_USBINTR);
|
|
writel(0, USB_OTGSC);
|
|
|
|
INIT_WORK(&motg->sm_work, msm_otg_sm_work);
|
|
INIT_DELAYED_WORK(&motg->chg_work, msm_chg_detect_work);
|
|
ret = devm_request_irq(&pdev->dev, motg->irq, msm_otg_irq, IRQF_SHARED,
|
|
"msm_otg", motg);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "request irq failed\n");
|
|
goto disable_ldo;
|
|
}
|
|
|
|
phy->init = msm_phy_init;
|
|
phy->set_power = msm_otg_set_power;
|
|
|
|
phy->io_ops = &msm_otg_io_ops;
|
|
|
|
phy->otg->phy = &motg->phy;
|
|
phy->otg->set_host = msm_otg_set_host;
|
|
phy->otg->set_peripheral = msm_otg_set_peripheral;
|
|
|
|
msm_usb_reset(phy);
|
|
|
|
ret = usb_add_phy(&motg->phy, USB_PHY_TYPE_USB2);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "usb_add_phy failed\n");
|
|
goto disable_ldo;
|
|
}
|
|
|
|
platform_set_drvdata(pdev, motg);
|
|
device_init_wakeup(&pdev->dev, 1);
|
|
|
|
if (motg->pdata->mode == USB_DR_MODE_OTG &&
|
|
motg->pdata->otg_control == OTG_USER_CONTROL) {
|
|
ret = msm_otg_debugfs_init(motg);
|
|
if (ret)
|
|
dev_dbg(&pdev->dev, "Can not create mode change file\n");
|
|
}
|
|
|
|
pm_runtime_set_active(&pdev->dev);
|
|
pm_runtime_enable(&pdev->dev);
|
|
|
|
return 0;
|
|
|
|
disable_ldo:
|
|
msm_hsusb_ldo_init(motg, 0);
|
|
disable_vddcx:
|
|
msm_hsusb_init_vddcx(motg, 0);
|
|
disable_clks:
|
|
clk_disable_unprepare(motg->pclk);
|
|
clk_disable_unprepare(motg->clk);
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_disable_unprepare(motg->core_clk);
|
|
return ret;
|
|
}
|
|
|
|
static int msm_otg_remove(struct platform_device *pdev)
|
|
{
|
|
struct msm_otg *motg = platform_get_drvdata(pdev);
|
|
struct usb_phy *phy = &motg->phy;
|
|
int cnt = 0;
|
|
|
|
if (phy->otg->host || phy->otg->gadget)
|
|
return -EBUSY;
|
|
|
|
msm_otg_debugfs_cleanup();
|
|
cancel_delayed_work_sync(&motg->chg_work);
|
|
cancel_work_sync(&motg->sm_work);
|
|
|
|
pm_runtime_resume(&pdev->dev);
|
|
|
|
device_init_wakeup(&pdev->dev, 0);
|
|
pm_runtime_disable(&pdev->dev);
|
|
|
|
usb_remove_phy(phy);
|
|
disable_irq(motg->irq);
|
|
|
|
/*
|
|
* Put PHY in low power mode.
|
|
*/
|
|
ulpi_read(phy, 0x14);
|
|
ulpi_write(phy, 0x08, 0x09);
|
|
|
|
writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
|
|
while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
|
|
if (readl(USB_PORTSC) & PORTSC_PHCD)
|
|
break;
|
|
udelay(1);
|
|
cnt++;
|
|
}
|
|
if (cnt >= PHY_SUSPEND_TIMEOUT_USEC)
|
|
dev_err(phy->dev, "Unable to suspend PHY\n");
|
|
|
|
clk_disable_unprepare(motg->pclk);
|
|
clk_disable_unprepare(motg->clk);
|
|
if (!IS_ERR(motg->core_clk))
|
|
clk_disable_unprepare(motg->core_clk);
|
|
msm_hsusb_ldo_init(motg, 0);
|
|
|
|
pm_runtime_set_suspended(&pdev->dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM_RUNTIME
|
|
static int msm_otg_runtime_idle(struct device *dev)
|
|
{
|
|
struct msm_otg *motg = dev_get_drvdata(dev);
|
|
struct usb_otg *otg = motg->phy.otg;
|
|
|
|
dev_dbg(dev, "OTG runtime idle\n");
|
|
|
|
/*
|
|
* It is observed some times that a spurious interrupt
|
|
* comes when PHY is put into LPM immediately after PHY reset.
|
|
* This 1 sec delay also prevents entering into LPM immediately
|
|
* after asynchronous interrupt.
|
|
*/
|
|
if (otg->phy->state != OTG_STATE_UNDEFINED)
|
|
pm_schedule_suspend(dev, 1000);
|
|
|
|
return -EAGAIN;
|
|
}
|
|
|
|
static int msm_otg_runtime_suspend(struct device *dev)
|
|
{
|
|
struct msm_otg *motg = dev_get_drvdata(dev);
|
|
|
|
dev_dbg(dev, "OTG runtime suspend\n");
|
|
return msm_otg_suspend(motg);
|
|
}
|
|
|
|
static int msm_otg_runtime_resume(struct device *dev)
|
|
{
|
|
struct msm_otg *motg = dev_get_drvdata(dev);
|
|
|
|
dev_dbg(dev, "OTG runtime resume\n");
|
|
return msm_otg_resume(motg);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int msm_otg_pm_suspend(struct device *dev)
|
|
{
|
|
struct msm_otg *motg = dev_get_drvdata(dev);
|
|
|
|
dev_dbg(dev, "OTG PM suspend\n");
|
|
return msm_otg_suspend(motg);
|
|
}
|
|
|
|
static int msm_otg_pm_resume(struct device *dev)
|
|
{
|
|
struct msm_otg *motg = dev_get_drvdata(dev);
|
|
int ret;
|
|
|
|
dev_dbg(dev, "OTG PM resume\n");
|
|
|
|
ret = msm_otg_resume(motg);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/*
|
|
* Runtime PM Documentation recommends bringing the
|
|
* device to full powered state upon resume.
|
|
*/
|
|
pm_runtime_disable(dev);
|
|
pm_runtime_set_active(dev);
|
|
pm_runtime_enable(dev);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct dev_pm_ops msm_otg_dev_pm_ops = {
|
|
SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
|
|
SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
|
|
msm_otg_runtime_idle)
|
|
};
|
|
|
|
static struct platform_driver msm_otg_driver = {
|
|
.probe = msm_otg_probe,
|
|
.remove = msm_otg_remove,
|
|
.driver = {
|
|
.name = DRIVER_NAME,
|
|
.owner = THIS_MODULE,
|
|
.pm = &msm_otg_dev_pm_ops,
|
|
.of_match_table = msm_otg_dt_match,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(msm_otg_driver);
|
|
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_DESCRIPTION("MSM USB transceiver driver");
|