![Matthieu Simon](/assets/img/avatar_default.png)
POKE32 and PEEK32 have been replaced by inlined functions poke32 and peek32. Having inline functions instead of macros help to get the correct type-checking and avoid the possible precedence issues reported by checkpatch. Signed-off-by: Matthieu Simon <gmatthsim@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
258 lines
5.5 KiB
C
258 lines
5.5 KiB
C
#define USE_HW_I2C
|
|
#ifdef USE_HW_I2C
|
|
#include "ddk750_chip.h"
|
|
#include "ddk750_reg.h"
|
|
#include "ddk750_hwi2c.h"
|
|
#include "ddk750_power.h"
|
|
|
|
#define MAX_HWI2C_FIFO 16
|
|
#define HWI2C_WAIT_TIMEOUT 0xF0000
|
|
|
|
int sm750_hw_i2c_init(
|
|
unsigned char bus_speed_mode
|
|
)
|
|
{
|
|
unsigned int value;
|
|
|
|
/* Enable GPIO 30 & 31 as IIC clock & data */
|
|
value = peek32(GPIO_MUX);
|
|
|
|
value |= (GPIO_MUX_30 | GPIO_MUX_31);
|
|
poke32(GPIO_MUX, value);
|
|
|
|
/*
|
|
* Enable Hardware I2C power.
|
|
* TODO: Check if we need to enable GPIO power?
|
|
*/
|
|
sm750_enable_i2c(1);
|
|
|
|
/* Enable the I2C Controller and set the bus speed mode */
|
|
value = peek32(I2C_CTRL) & ~(I2C_CTRL_MODE | I2C_CTRL_EN);
|
|
if (bus_speed_mode)
|
|
value |= I2C_CTRL_MODE;
|
|
value |= I2C_CTRL_EN;
|
|
poke32(I2C_CTRL, value);
|
|
|
|
return 0;
|
|
}
|
|
|
|
void sm750_hw_i2c_close(void)
|
|
{
|
|
unsigned int value;
|
|
|
|
/* Disable I2C controller */
|
|
value = peek32(I2C_CTRL) & ~I2C_CTRL_EN;
|
|
poke32(I2C_CTRL, value);
|
|
|
|
/* Disable I2C Power */
|
|
sm750_enable_i2c(0);
|
|
|
|
/* Set GPIO 30 & 31 back as GPIO pins */
|
|
value = peek32(GPIO_MUX);
|
|
value &= ~GPIO_MUX_30;
|
|
value &= ~GPIO_MUX_31;
|
|
poke32(GPIO_MUX, value);
|
|
}
|
|
|
|
static long hw_i2c_wait_tx_done(void)
|
|
{
|
|
unsigned int timeout;
|
|
|
|
/* Wait until the transfer is completed. */
|
|
timeout = HWI2C_WAIT_TIMEOUT;
|
|
while (!(peek32(I2C_STATUS) & I2C_STATUS_TX) && (timeout != 0))
|
|
timeout--;
|
|
|
|
if (timeout == 0)
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* This function writes data to the i2c slave device registers.
|
|
*
|
|
* Parameters:
|
|
* addr - i2c Slave device address
|
|
* length - Total number of bytes to be written to the device
|
|
* buf - The buffer that contains the data to be written to the
|
|
* i2c device.
|
|
*
|
|
* Return Value:
|
|
* Total number of bytes those are actually written.
|
|
*/
|
|
static unsigned int hw_i2c_write_data(
|
|
unsigned char addr,
|
|
unsigned int length,
|
|
unsigned char *buf
|
|
)
|
|
{
|
|
unsigned char count, i;
|
|
unsigned int total_bytes = 0;
|
|
|
|
/* Set the Device Address */
|
|
poke32(I2C_SLAVE_ADDRESS, addr & ~0x01);
|
|
|
|
/*
|
|
* Write data.
|
|
* Note:
|
|
* Only 16 byte can be accessed per i2c start instruction.
|
|
*/
|
|
do {
|
|
/*
|
|
* Reset I2C by writing 0 to I2C_RESET register to
|
|
* clear the previous status.
|
|
*/
|
|
poke32(I2C_RESET, 0);
|
|
|
|
/* Set the number of bytes to be written */
|
|
if (length < MAX_HWI2C_FIFO)
|
|
count = length - 1;
|
|
else
|
|
count = MAX_HWI2C_FIFO - 1;
|
|
poke32(I2C_BYTE_COUNT, count);
|
|
|
|
/* Move the data to the I2C data register */
|
|
for (i = 0; i <= count; i++)
|
|
poke32(I2C_DATA0 + i, *buf++);
|
|
|
|
/* Start the I2C */
|
|
poke32(I2C_CTRL, peek32(I2C_CTRL) | I2C_CTRL_CTRL);
|
|
|
|
/* Wait until the transfer is completed. */
|
|
if (hw_i2c_wait_tx_done() != 0)
|
|
break;
|
|
|
|
/* Subtract length */
|
|
length -= (count + 1);
|
|
|
|
/* Total byte written */
|
|
total_bytes += (count + 1);
|
|
|
|
} while (length > 0);
|
|
|
|
return total_bytes;
|
|
}
|
|
|
|
/*
|
|
* This function reads data from the slave device and stores them
|
|
* in the given buffer
|
|
*
|
|
* Parameters:
|
|
* addr - i2c Slave device address
|
|
* length - Total number of bytes to be read
|
|
* buf - Pointer to a buffer to be filled with the data read
|
|
* from the slave device. It has to be the same size as the
|
|
* length to make sure that it can keep all the data read.
|
|
*
|
|
* Return Value:
|
|
* Total number of actual bytes read from the slave device
|
|
*/
|
|
static unsigned int hw_i2c_read_data(
|
|
unsigned char addr,
|
|
unsigned int length,
|
|
unsigned char *buf
|
|
)
|
|
{
|
|
unsigned char count, i;
|
|
unsigned int total_bytes = 0;
|
|
|
|
/* Set the Device Address */
|
|
poke32(I2C_SLAVE_ADDRESS, addr | 0x01);
|
|
|
|
/*
|
|
* Read data and save them to the buffer.
|
|
* Note:
|
|
* Only 16 byte can be accessed per i2c start instruction.
|
|
*/
|
|
do {
|
|
/*
|
|
* Reset I2C by writing 0 to I2C_RESET register to
|
|
* clear all the status.
|
|
*/
|
|
poke32(I2C_RESET, 0);
|
|
|
|
/* Set the number of bytes to be read */
|
|
if (length <= MAX_HWI2C_FIFO)
|
|
count = length - 1;
|
|
else
|
|
count = MAX_HWI2C_FIFO - 1;
|
|
poke32(I2C_BYTE_COUNT, count);
|
|
|
|
/* Start the I2C */
|
|
poke32(I2C_CTRL, peek32(I2C_CTRL) | I2C_CTRL_CTRL);
|
|
|
|
/* Wait until transaction done. */
|
|
if (hw_i2c_wait_tx_done() != 0)
|
|
break;
|
|
|
|
/* Save the data to the given buffer */
|
|
for (i = 0; i <= count; i++)
|
|
*buf++ = peek32(I2C_DATA0 + i);
|
|
|
|
/* Subtract length by 16 */
|
|
length -= (count + 1);
|
|
|
|
/* Number of bytes read. */
|
|
total_bytes += (count + 1);
|
|
|
|
} while (length > 0);
|
|
|
|
return total_bytes;
|
|
}
|
|
|
|
/*
|
|
* This function reads the slave device's register
|
|
*
|
|
* Parameters:
|
|
* deviceAddress - i2c Slave device address which register
|
|
* to be read from
|
|
* registerIndex - Slave device's register to be read
|
|
*
|
|
* Return Value:
|
|
* Register value
|
|
*/
|
|
unsigned char sm750_hw_i2c_read_reg(
|
|
unsigned char addr,
|
|
unsigned char reg
|
|
)
|
|
{
|
|
unsigned char value = (0xFF);
|
|
|
|
if (hw_i2c_write_data(addr, 1, ®) == 1)
|
|
hw_i2c_read_data(addr, 1, &value);
|
|
|
|
return value;
|
|
}
|
|
|
|
/*
|
|
* This function writes a value to the slave device's register
|
|
*
|
|
* Parameters:
|
|
* deviceAddress - i2c Slave device address which register
|
|
* to be written
|
|
* registerIndex - Slave device's register to be written
|
|
* data - Data to be written to the register
|
|
*
|
|
* Result:
|
|
* 0 - Success
|
|
* -1 - Fail
|
|
*/
|
|
int sm750_hw_i2c_write_reg(
|
|
unsigned char addr,
|
|
unsigned char reg,
|
|
unsigned char data
|
|
)
|
|
{
|
|
unsigned char value[2];
|
|
|
|
value[0] = reg;
|
|
value[1] = data;
|
|
if (hw_i2c_write_data(addr, 2, value) == 2)
|
|
return 0;
|
|
|
|
return -1;
|
|
}
|
|
|
|
#endif
|