![Jon Hunter](/assets/img/avatar_default.png)
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960
("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
709 lines
16 KiB
Plaintext
709 lines
16 KiB
Plaintext
#include <dt-bindings/input/input.h>
|
|
#include "tegra124.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
rtc0 = "/i2c@0,7000d000/pmic@40";
|
|
rtc1 = "/rtc@0,7000e000";
|
|
serial0 = &uarta;
|
|
};
|
|
|
|
memory {
|
|
reg = <0x0 0x80000000 0x0 0x80000000>;
|
|
};
|
|
|
|
host1x@0,50000000 {
|
|
hdmi@0,54280000 {
|
|
status = "okay";
|
|
|
|
vdd-supply = <&vdd_3v3_hdmi>;
|
|
pll-supply = <&vdd_hdmi_pll>;
|
|
hdmi-supply = <&vdd_5v0_hdmi>;
|
|
|
|
nvidia,ddc-i2c-bus = <&hdmi_ddc>;
|
|
nvidia,hpd-gpio =
|
|
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sor@0,54540000 {
|
|
status = "okay";
|
|
|
|
nvidia,dpaux = <&dpaux>;
|
|
nvidia,panel = <&panel>;
|
|
};
|
|
|
|
dpaux@0,545c0000 {
|
|
vdd-supply = <&vdd_3v3_panel>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
serial@0,70006000 {
|
|
/* Debug connector on the bottom of the board near SD card. */
|
|
status = "okay";
|
|
};
|
|
|
|
pwm@0,7000a000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@0,7000c000 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
acodec: audio-codec@10 {
|
|
compatible = "maxim,max98090";
|
|
reg = <0x10>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
temperature-sensor@4c {
|
|
compatible = "ti,tmp451";
|
|
reg = <0x4c>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
#thermal-sensor-cells = <1>;
|
|
};
|
|
};
|
|
|
|
i2c@0,7000c400 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
trackpad@15 {
|
|
compatible = "elan,ekth3000";
|
|
reg = <0x15>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
|
|
wakeup-source;
|
|
};
|
|
};
|
|
|
|
i2c@0,7000c500 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
tpm@20 {
|
|
compatible = "infineon,slb9645tt";
|
|
reg = <0x20>;
|
|
};
|
|
};
|
|
|
|
hdmi_ddc: i2c@0,7000c700 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
i2c@0,7000d000 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
pmic: pmic@40 {
|
|
compatible = "ams,as3722";
|
|
reg = <0x40>;
|
|
interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
ams,system-power-controller;
|
|
|
|
#interrupt-cells = <2>;
|
|
interrupt-controller;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&as3722_default>;
|
|
|
|
as3722_default: pinmux {
|
|
gpio0 {
|
|
pins = "gpio0";
|
|
function = "gpio";
|
|
bias-pull-down;
|
|
};
|
|
|
|
gpio1 {
|
|
pins = "gpio1";
|
|
function = "gpio";
|
|
bias-pull-up;
|
|
};
|
|
|
|
gpio2_4_7 {
|
|
pins = "gpio2", "gpio4", "gpio7";
|
|
function = "gpio";
|
|
bias-pull-up;
|
|
};
|
|
|
|
gpio3_6 {
|
|
pins = "gpio3", "gpio6";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
gpio5 {
|
|
pins = "gpio5";
|
|
function = "clk32k-out";
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
vsup-sd2-supply = <&vdd_5v0_sys>;
|
|
vsup-sd3-supply = <&vdd_5v0_sys>;
|
|
vsup-sd4-supply = <&vdd_5v0_sys>;
|
|
vsup-sd5-supply = <&vdd_5v0_sys>;
|
|
vin-ldo0-supply = <&vdd_1v35_lp0>;
|
|
vin-ldo1-6-supply = <&vdd_3v3_run>;
|
|
vin-ldo2-5-7-supply = <&vddio_1v8>;
|
|
vin-ldo3-4-supply = <&vdd_3v3_sys>;
|
|
vin-ldo9-10-supply = <&vdd_5v0_sys>;
|
|
vin-ldo11-supply = <&vdd_3v3_run>;
|
|
|
|
vdd_cpu: sd0 {
|
|
regulator-name = "+VDD_CPU_AP";
|
|
regulator-min-microvolt = <700000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-min-microamp = <3500000>;
|
|
regulator-max-microamp = <3500000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
ams,ext-control = <2>;
|
|
};
|
|
|
|
sd1 {
|
|
regulator-name = "+VDD_CORE";
|
|
regulator-min-microvolt = <700000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-min-microamp = <2500000>;
|
|
regulator-max-microamp = <4000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
ams,ext-control = <1>;
|
|
};
|
|
|
|
vdd_1v35_lp0: sd2 {
|
|
regulator-name = "+1.35V_LP0(sd2)";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
sd3 {
|
|
regulator-name = "+1.35V_LP0(sd3)";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vdd_1v05_run: sd4 {
|
|
regulator-name = "+1.05V_RUN";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
};
|
|
|
|
vddio_1v8: sd5 {
|
|
regulator-name = "+1.8V_VDDIO";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
sd6 {
|
|
regulator-name = "+VDD_GPU_AP";
|
|
regulator-min-microvolt = <650000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-min-microamp = <3500000>;
|
|
regulator-max-microamp = <3500000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo0 {
|
|
regulator-name = "+1.05V_RUN_AVDD";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
ams,ext-control = <1>;
|
|
};
|
|
|
|
ldo1 {
|
|
regulator-name = "+1.8V_RUN_CAM";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
ldo2 {
|
|
regulator-name = "+1.2V_GEN_AVDD";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo3 {
|
|
regulator-name = "+1.00V_LP0_VDD_RTC";
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
ams,enable-tracking;
|
|
};
|
|
|
|
vdd_run_cam: ldo4 {
|
|
regulator-name = "+3.3V_RUN_CAM";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo5 {
|
|
regulator-name = "+1.2V_RUN_CAM_FRONT";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
vddio_sdmmc3: ldo6 {
|
|
regulator-name = "+VDDIO_SDMMC3";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo7 {
|
|
regulator-name = "+1.05V_RUN_CAM_REAR";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
};
|
|
|
|
ldo9 {
|
|
regulator-name = "+2.8V_RUN_TOUCH";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo10 {
|
|
regulator-name = "+2.8V_RUN_CAM_AF";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo11 {
|
|
regulator-name = "+1.8V_RUN_VPP_FUSE";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
spi@0,7000d400 {
|
|
status = "okay";
|
|
|
|
cros_ec: cros-ec@0 {
|
|
compatible = "google,cros-ec-spi";
|
|
spi-max-frequency = <3000000>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
|
|
reg = <0>;
|
|
|
|
google,cros-ec-spi-msg-delay = <2000>;
|
|
|
|
i2c-tunnel {
|
|
compatible = "google,cros-ec-i2c-tunnel";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
google,remote-bus = <0>;
|
|
|
|
charger: bq24735@9 {
|
|
compatible = "ti,bq24735";
|
|
reg = <0x9>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(J, 0)
|
|
GPIO_ACTIVE_HIGH>;
|
|
ti,ac-detect-gpios = <&gpio
|
|
TEGRA_GPIO(J, 0)
|
|
GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
battery: sbs-battery@b {
|
|
compatible = "sbs,sbs-battery";
|
|
reg = <0xb>;
|
|
sbs,i2c-retry-count = <2>;
|
|
sbs,poll-retry-count = <10>;
|
|
power-supplies = <&charger>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
spi@0,7000da00 {
|
|
status = "okay";
|
|
spi-max-frequency = <25000000>;
|
|
|
|
flash@0 {
|
|
compatible = "winbond,w25q32dw";
|
|
spi-max-frequency = <25000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
pmc@0,7000e400 {
|
|
nvidia,invert-interrupt;
|
|
nvidia,suspend-mode = <0>;
|
|
nvidia,cpu-pwr-good-time = <500>;
|
|
nvidia,cpu-pwr-off-time = <300>;
|
|
nvidia,core-pwr-good-time = <641 3845>;
|
|
nvidia,core-pwr-off-time = <61036>;
|
|
nvidia,core-power-req-active-high;
|
|
nvidia,sys-clock-req-active-high;
|
|
};
|
|
|
|
hda@0,70030000 {
|
|
status = "okay";
|
|
};
|
|
|
|
sdhci0_pwrseq: sdhci0_pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
|
|
reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sdhci@0,700b0000 { /* WiFi/BT on this bus */
|
|
status = "okay";
|
|
bus-width = <4>;
|
|
no-1-8-v;
|
|
non-removable;
|
|
mmc-pwrseq = <&sdhci0_pwrseq>;
|
|
vmmc-supply = <&vdd_3v3_lp0>;
|
|
vqmmc-supply = <&vddio_1v8>;
|
|
keep-power-in-suspend;
|
|
};
|
|
|
|
sdhci@0,700b0400 { /* SD Card on this bus */
|
|
status = "okay";
|
|
cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
|
|
power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
|
|
bus-width = <4>;
|
|
no-1-8-v;
|
|
vqmmc-supply = <&vddio_sdmmc3>;
|
|
};
|
|
|
|
sdhci@0,700b0600 { /* eMMC on this bus */
|
|
status = "okay";
|
|
bus-width = <8>;
|
|
no-1-8-v;
|
|
non-removable;
|
|
};
|
|
|
|
/* CPU DFLL clock */
|
|
clock@0,70110000 {
|
|
status = "disabled";
|
|
vdd-cpu-supply = <&vdd_cpu>;
|
|
nvidia,i2c-fs-rate = <400000>;
|
|
};
|
|
|
|
ahub@0,70300000 {
|
|
i2s@0,70301100 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
usb@0,7d000000 { /* Rear external USB port. */
|
|
status = "okay";
|
|
};
|
|
|
|
usb-phy@0,7d000000 {
|
|
status = "okay";
|
|
vbus-supply = <&vdd_usb1_vbus>;
|
|
};
|
|
|
|
usb@0,7d004000 { /* Internal webcam. */
|
|
status = "okay";
|
|
};
|
|
|
|
usb-phy@0,7d004000 {
|
|
status = "okay";
|
|
vbus-supply = <&vdd_run_cam>;
|
|
};
|
|
|
|
usb@0,7d008000 { /* Left external USB port. */
|
|
status = "okay";
|
|
};
|
|
|
|
usb-phy@0,7d008000 {
|
|
status = "okay";
|
|
vbus-supply = <&vdd_usb3_vbus>;
|
|
};
|
|
|
|
backlight: backlight {
|
|
compatible = "pwm-backlight";
|
|
|
|
enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
|
|
power-supply = <&vdd_led>;
|
|
pwms = <&pwm 1 1000000>;
|
|
|
|
default-brightness-level = <224>;
|
|
brightness-levels =
|
|
< 0 1 2 3 4 5 6 7
|
|
8 9 10 11 12 13 14 15
|
|
16 17 18 19 20 21 22 23
|
|
24 25 26 27 28 29 30 31
|
|
32 33 34 35 36 37 38 39
|
|
40 41 42 43 44 45 46 47
|
|
48 49 50 51 52 53 54 55
|
|
56 57 58 59 60 61 62 63
|
|
64 65 66 67 68 69 70 71
|
|
72 73 74 75 76 77 78 79
|
|
80 81 82 83 84 85 86 87
|
|
88 89 90 91 92 93 94 95
|
|
96 97 98 99 100 101 102 103
|
|
104 105 106 107 108 109 110 111
|
|
112 113 114 115 116 117 118 119
|
|
120 121 122 123 124 125 126 127
|
|
128 129 130 131 132 133 134 135
|
|
136 137 138 139 140 141 142 143
|
|
144 145 146 147 148 149 150 151
|
|
152 153 154 155 156 157 158 159
|
|
160 161 162 163 164 165 166 167
|
|
168 169 170 171 172 173 174 175
|
|
176 177 178 179 180 181 182 183
|
|
184 185 186 187 188 189 190 191
|
|
192 193 194 195 196 197 198 199
|
|
200 201 202 203 204 205 206 207
|
|
208 209 210 211 212 213 214 215
|
|
216 217 218 219 220 221 222 223
|
|
224 225 226 227 228 229 230 231
|
|
232 233 234 235 236 237 238 239
|
|
240 241 242 243 244 245 246 247
|
|
248 249 250 251 252 253 254 255
|
|
256>;
|
|
};
|
|
|
|
clocks {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
clk32k_in: clock@0 {
|
|
compatible = "fixed-clock";
|
|
reg = <0>;
|
|
#clock-cells = <0>;
|
|
clock-frequency = <32768>;
|
|
};
|
|
};
|
|
|
|
cpus {
|
|
cpu@0 {
|
|
vdd-cpu-supply = <&vdd_cpu>;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
lid {
|
|
label = "Lid";
|
|
gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <5>;
|
|
linux,code = <KEY_RESERVED>;
|
|
debounce-interval = <1>;
|
|
gpio-key,wakeup;
|
|
};
|
|
|
|
power {
|
|
label = "Power";
|
|
gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_POWER>;
|
|
debounce-interval = <30>;
|
|
gpio-key,wakeup;
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
vdd_mux: regulator@0 {
|
|
compatible = "regulator-fixed";
|
|
reg = <0>;
|
|
regulator-name = "+VDD_MUX";
|
|
regulator-min-microvolt = <12000000>;
|
|
regulator-max-microvolt = <12000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vdd_5v0_sys: regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "+5V_SYS";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
vin-supply = <&vdd_mux>;
|
|
};
|
|
|
|
vdd_3v3_sys: regulator@2 {
|
|
compatible = "regulator-fixed";
|
|
reg = <2>;
|
|
regulator-name = "+3.3V_SYS";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
vin-supply = <&vdd_mux>;
|
|
};
|
|
|
|
vdd_3v3_run: regulator@3 {
|
|
compatible = "regulator-fixed";
|
|
reg = <3>;
|
|
regulator-name = "+3.3V_RUN";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_3v3_sys>;
|
|
};
|
|
|
|
vdd_3v3_hdmi: regulator@4 {
|
|
compatible = "regulator-fixed";
|
|
reg = <4>;
|
|
regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&vdd_3v3_run>;
|
|
};
|
|
|
|
vdd_led: regulator@5 {
|
|
compatible = "regulator-fixed";
|
|
reg = <5>;
|
|
regulator-name = "+VDD_LED";
|
|
gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_mux>;
|
|
};
|
|
|
|
vdd_5v0_ts: regulator@6 {
|
|
compatible = "regulator-fixed";
|
|
reg = <6>;
|
|
regulator-name = "+5V_VDD_TS_SW";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-boot-on;
|
|
gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_5v0_sys>;
|
|
};
|
|
|
|
vdd_usb1_vbus: regulator@7 {
|
|
compatible = "regulator-fixed";
|
|
reg = <7>;
|
|
regulator-name = "+5V_USB_HS";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
gpio-open-drain;
|
|
vin-supply = <&vdd_5v0_sys>;
|
|
};
|
|
|
|
vdd_usb3_vbus: regulator@8 {
|
|
compatible = "regulator-fixed";
|
|
reg = <8>;
|
|
regulator-name = "+5V_USB_SS";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
gpio-open-drain;
|
|
vin-supply = <&vdd_5v0_sys>;
|
|
};
|
|
|
|
vdd_3v3_panel: regulator@9 {
|
|
compatible = "regulator-fixed";
|
|
reg = <9>;
|
|
regulator-name = "+3.3V_PANEL";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_3v3_run>;
|
|
};
|
|
|
|
vdd_3v3_lp0: regulator@10 {
|
|
compatible = "regulator-fixed";
|
|
reg = <10>;
|
|
regulator-name = "+3.3V_LP0";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
/*
|
|
* TODO: find a way to wire this up with the USB EHCI
|
|
* controllers so that it can be enabled on demand.
|
|
*/
|
|
regulator-always-on;
|
|
gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_3v3_sys>;
|
|
};
|
|
|
|
vdd_hdmi_pll: regulator@11 {
|
|
compatible = "regulator-fixed";
|
|
reg = <11>;
|
|
regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
|
|
vin-supply = <&vdd_1v05_run>;
|
|
};
|
|
|
|
vdd_5v0_hdmi: regulator@12 {
|
|
compatible = "regulator-fixed";
|
|
reg = <12>;
|
|
regulator-name = "+5V_HDMI_CON";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
vin-supply = <&vdd_5v0_sys>;
|
|
};
|
|
};
|
|
|
|
sound {
|
|
nvidia,audio-routing =
|
|
"Headphones", "HPR",
|
|
"Headphones", "HPL",
|
|
"Speakers", "SPKR",
|
|
"Speakers", "SPKL",
|
|
"Mic Jack", "MICBIAS",
|
|
"DMICL", "Int Mic",
|
|
"DMICR", "Int Mic",
|
|
"IN34", "Mic Jack";
|
|
|
|
nvidia,i2s-controller = <&tegra_i2s1>;
|
|
nvidia,audio-codec = <&acodec>;
|
|
|
|
clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
|
|
<&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
|
|
<&tegra_car TEGRA124_CLK_EXTERN1>;
|
|
clock-names = "pll_a", "pll_a_out0", "mclk";
|
|
|
|
nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
|
|
nvidia,mic-det-gpios =
|
|
<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
gpio-restart {
|
|
compatible = "gpio-restart";
|
|
gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
|
|
priority = <200>;
|
|
};
|
|
};
|
|
|
|
#include "cros-ec-keyboard.dtsi"
|