![Lennert Buytenhek](/assets/img/avatar_default.png)
This patch makes the various mach dirs that use the plat-orion time code pass in timer and bridge addresses explicitly, instead of having plat-orion get those values by including a mach dir include file -- the latter mechanism is problematic if you want to support multiple ARM platforms in the same kernel image. Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca> Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
249 lines
5.6 KiB
C
249 lines
5.6 KiB
C
/*
|
|
* arch/arm/mach-kirkwood/openrd-setup.c
|
|
*
|
|
* Marvell OpenRD (Base|Client|Ultimate) Board Setup
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/ata_platform.h>
|
|
#include <linux/mv643xx_eth.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/gpio.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <mach/kirkwood.h>
|
|
#include <plat/mvsdio.h>
|
|
#include "common.h"
|
|
#include "mpp.h"
|
|
|
|
static struct mtd_partition openrd_nand_parts[] = {
|
|
{
|
|
.name = "u-boot",
|
|
.offset = 0,
|
|
.size = SZ_1M,
|
|
.mask_flags = MTD_WRITEABLE
|
|
}, {
|
|
.name = "uImage",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = SZ_4M
|
|
}, {
|
|
.name = "root",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = MTDPART_SIZ_FULL
|
|
},
|
|
};
|
|
|
|
static struct mv643xx_eth_platform_data openrd_ge00_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
|
|
};
|
|
|
|
static struct mv643xx_eth_platform_data openrd_ge01_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_ADDR(24),
|
|
};
|
|
|
|
static struct mv_sata_platform_data openrd_sata_data = {
|
|
.n_ports = 2,
|
|
};
|
|
|
|
static struct mvsdio_platform_data openrd_mvsdio_data = {
|
|
.gpio_card_detect = 29, /* MPP29 used as SD card detect */
|
|
};
|
|
|
|
static unsigned int openrd_mpp_config[] __initdata = {
|
|
MPP12_SD_CLK,
|
|
MPP13_SD_CMD,
|
|
MPP14_SD_D0,
|
|
MPP15_SD_D1,
|
|
MPP16_SD_D2,
|
|
MPP17_SD_D3,
|
|
MPP28_GPIO,
|
|
MPP29_GPIO,
|
|
MPP34_GPIO,
|
|
0
|
|
};
|
|
|
|
/* Configure MPP for UART1 */
|
|
static unsigned int openrd_uart1_mpp_config[] __initdata = {
|
|
MPP13_UART1_TXD,
|
|
MPP14_UART1_RXD,
|
|
0
|
|
};
|
|
|
|
static struct i2c_board_info i2c_board_info[] __initdata = {
|
|
{
|
|
I2C_BOARD_INFO("cs42l51", 0x4a),
|
|
},
|
|
};
|
|
|
|
static int __initdata uart1;
|
|
|
|
static int __init sd_uart_selection(char *str)
|
|
{
|
|
uart1 = -EINVAL;
|
|
|
|
/* Default is SD. Change if required, for UART */
|
|
if (!str)
|
|
return 0;
|
|
|
|
if (!strncmp(str, "232", 3)) {
|
|
uart1 = 232;
|
|
} else if (!strncmp(str, "485", 3)) {
|
|
/* OpenRD-Base doesn't have RS485. Treat is as an
|
|
* unknown argument & just have default setting -
|
|
* which is SD */
|
|
if (machine_is_openrd_base()) {
|
|
uart1 = -ENODEV;
|
|
return 1;
|
|
}
|
|
|
|
uart1 = 485;
|
|
}
|
|
return 1;
|
|
}
|
|
/* Parse boot_command_line string kw_openrd_init_uart1=232/485 */
|
|
__setup("kw_openrd_init_uart1=", sd_uart_selection);
|
|
|
|
static int __init uart1_mpp_config(void)
|
|
{
|
|
kirkwood_mpp_conf(openrd_uart1_mpp_config);
|
|
|
|
if (gpio_request(34, "SD_UART1_SEL")) {
|
|
printk(KERN_ERR "GPIO request failed for SD/UART1 selection"
|
|
", gpio: 34\n");
|
|
return -EIO;
|
|
}
|
|
|
|
if (gpio_request(28, "RS232_RS485_SEL")) {
|
|
printk(KERN_ERR "GPIO request failed for RS232/RS485 selection"
|
|
", gpio# 28\n");
|
|
gpio_free(34);
|
|
return -EIO;
|
|
}
|
|
|
|
/* Select UART1
|
|
* Pin # 34: 0 => UART1, 1 => SD */
|
|
gpio_direction_output(34, 0);
|
|
|
|
/* Select RS232 OR RS485
|
|
* Pin # 28: 0 => RS232, 1 => RS485 */
|
|
if (uart1 == 232)
|
|
gpio_direction_output(28, 0);
|
|
else
|
|
gpio_direction_output(28, 1);
|
|
|
|
gpio_free(34);
|
|
gpio_free(28);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void __init openrd_init(void)
|
|
{
|
|
/*
|
|
* Basic setup. Needs to be called early.
|
|
*/
|
|
kirkwood_init();
|
|
kirkwood_mpp_conf(openrd_mpp_config);
|
|
|
|
kirkwood_uart0_init();
|
|
kirkwood_nand_init(ARRAY_AND_SIZE(openrd_nand_parts), 25);
|
|
|
|
kirkwood_ehci_init();
|
|
|
|
if (machine_is_openrd_ultimate()) {
|
|
openrd_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
|
|
openrd_ge01_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
|
|
}
|
|
|
|
kirkwood_ge00_init(&openrd_ge00_data);
|
|
if (!machine_is_openrd_base())
|
|
kirkwood_ge01_init(&openrd_ge01_data);
|
|
|
|
kirkwood_sata_init(&openrd_sata_data);
|
|
|
|
kirkwood_i2c_init();
|
|
|
|
if (machine_is_openrd_client() || machine_is_openrd_ultimate()) {
|
|
i2c_register_board_info(0, i2c_board_info,
|
|
ARRAY_SIZE(i2c_board_info));
|
|
kirkwood_audio_init();
|
|
}
|
|
|
|
if (uart1 <= 0) {
|
|
if (uart1 < 0)
|
|
printk(KERN_ERR "Invalid kernel parameter to select "
|
|
"UART1. Defaulting to SD. ERROR CODE: %d\n",
|
|
uart1);
|
|
|
|
/* Select SD
|
|
* Pin # 34: 0 => UART1, 1 => SD */
|
|
if (gpio_request(34, "SD_UART1_SEL")) {
|
|
printk(KERN_ERR "GPIO request failed for SD/UART1 "
|
|
"selection, gpio: 34\n");
|
|
} else {
|
|
|
|
gpio_direction_output(34, 1);
|
|
gpio_free(34);
|
|
kirkwood_sdio_init(&openrd_mvsdio_data);
|
|
}
|
|
} else {
|
|
if (!uart1_mpp_config())
|
|
kirkwood_uart1_init();
|
|
}
|
|
}
|
|
|
|
static int __init openrd_pci_init(void)
|
|
{
|
|
if (machine_is_openrd_base() ||
|
|
machine_is_openrd_client() ||
|
|
machine_is_openrd_ultimate())
|
|
kirkwood_pcie_init(KW_PCIE0);
|
|
|
|
return 0;
|
|
}
|
|
subsys_initcall(openrd_pci_init);
|
|
|
|
#ifdef CONFIG_MACH_OPENRD_BASE
|
|
MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board")
|
|
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
|
|
.boot_params = 0x00000100,
|
|
.init_machine = openrd_init,
|
|
.map_io = kirkwood_map_io,
|
|
.init_early = kirkwood_init_early,
|
|
.init_irq = kirkwood_init_irq,
|
|
.timer = &kirkwood_timer,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_OPENRD_CLIENT
|
|
MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board")
|
|
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
|
|
.boot_params = 0x00000100,
|
|
.init_machine = openrd_init,
|
|
.map_io = kirkwood_map_io,
|
|
.init_early = kirkwood_init_early,
|
|
.init_irq = kirkwood_init_irq,
|
|
.timer = &kirkwood_timer,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_OPENRD_ULTIMATE
|
|
MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board")
|
|
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
|
|
.boot_params = 0x00000100,
|
|
.init_machine = openrd_init,
|
|
.map_io = kirkwood_map_io,
|
|
.init_early = kirkwood_init_early,
|
|
.init_irq = kirkwood_init_irq,
|
|
.timer = &kirkwood_timer,
|
|
MACHINE_END
|
|
#endif
|