![Herbert Xu](/assets/img/avatar_default.png)
First of all it is unnecessary to allocate a new skb in skb_pad since the existing one is not shared. More importantly, our hard_start_xmit interface does not allow a new skb to be allocated since that breaks requeueing. This patch uses pskb_expand_head to expand the existing skb and linearize it if needed. Actually, someone should sift through every instance of skb_pad on a non-linear skb as they do not fit the reasons why this was originally created. Incidentally, this fixes a minor bug when the skb is cloned (tcpdump, TCP, etc.). As it is skb_pad will simply write over a cloned skb. Because of the position of the write it is unlikely to cause problems but still it's best if we don't do it. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
935 lines
24 KiB
C
935 lines
24 KiB
C
/*
|
|
* linux/drivers/acorn/net/ether3.c
|
|
*
|
|
* Copyright (C) 1995-2000 Russell King
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* SEEQ nq8005 ethernet driver for Acorn/ANT Ether3 card
|
|
* for Acorn machines
|
|
*
|
|
* By Russell King, with some suggestions from borris@ant.co.uk
|
|
*
|
|
* Changelog:
|
|
* 1.04 RMK 29/02/1996 Won't pass packets that are from our ethernet
|
|
* address up to the higher levels - they're
|
|
* silently ignored. I/F can now be put into
|
|
* multicast mode. Receiver routine optimised.
|
|
* 1.05 RMK 30/02/1996 Now claims interrupt at open when part of
|
|
* the kernel rather than when a module.
|
|
* 1.06 RMK 02/03/1996 Various code cleanups
|
|
* 1.07 RMK 13/10/1996 Optimised interrupt routine and transmit
|
|
* routines.
|
|
* 1.08 RMK 14/10/1996 Fixed problem with too many packets,
|
|
* prevented the kernel message about dropped
|
|
* packets appearing too many times a second.
|
|
* Now does not disable all IRQs, only the IRQ
|
|
* used by this card.
|
|
* 1.09 RMK 10/11/1996 Only enables TX irq when buffer space is low,
|
|
* but we still service the TX queue if we get a
|
|
* RX interrupt.
|
|
* 1.10 RMK 15/07/1997 Fixed autoprobing of NQ8004.
|
|
* 1.11 RMK 16/11/1997 Fixed autoprobing of NQ8005A.
|
|
* 1.12 RMK 31/12/1997 Removed reference to dev_tint for Linux 2.1.
|
|
* RMK 27/06/1998 Changed asm/delay.h to linux/delay.h.
|
|
* 1.13 RMK 29/06/1998 Fixed problem with transmission of packets.
|
|
* Chip seems to have a bug in, whereby if the
|
|
* packet starts two bytes from the end of the
|
|
* buffer, it corrupts the receiver chain, and
|
|
* never updates the transmit status correctly.
|
|
* 1.14 RMK 07/01/1998 Added initial code for ETHERB addressing.
|
|
* 1.15 RMK 30/04/1999 More fixes to the transmit routine for buggy
|
|
* hardware.
|
|
* 1.16 RMK 10/02/2000 Updated for 2.3.43
|
|
* 1.17 RMK 13/05/2000 Updated for 2.3.99-pre8
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/types.h>
|
|
#include <linux/fcntl.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/ptrace.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/in.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/string.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/etherdevice.h>
|
|
#include <linux/skbuff.h>
|
|
#include <linux/device.h>
|
|
#include <linux/init.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/bitops.h>
|
|
|
|
#include <asm/system.h>
|
|
#include <asm/ecard.h>
|
|
#include <asm/io.h>
|
|
|
|
static char version[] __initdata = "ether3 ethernet driver (c) 1995-2000 R.M.King v1.17\n";
|
|
|
|
#include "ether3.h"
|
|
|
|
static unsigned int net_debug = NET_DEBUG;
|
|
|
|
static void ether3_setmulticastlist(struct net_device *dev);
|
|
static int ether3_rx(struct net_device *dev, unsigned int maxcnt);
|
|
static void ether3_tx(struct net_device *dev);
|
|
static int ether3_open (struct net_device *dev);
|
|
static int ether3_sendpacket (struct sk_buff *skb, struct net_device *dev);
|
|
static irqreturn_t ether3_interrupt (int irq, void *dev_id, struct pt_regs *regs);
|
|
static int ether3_close (struct net_device *dev);
|
|
static struct net_device_stats *ether3_getstats (struct net_device *dev);
|
|
static void ether3_setmulticastlist (struct net_device *dev);
|
|
static void ether3_timeout(struct net_device *dev);
|
|
|
|
#define BUS_16 2
|
|
#define BUS_8 1
|
|
#define BUS_UNKNOWN 0
|
|
|
|
/* --------------------------------------------------------------------------- */
|
|
|
|
typedef enum {
|
|
buffer_write,
|
|
buffer_read
|
|
} buffer_rw_t;
|
|
|
|
/*
|
|
* ether3 read/write. Slow things down a bit...
|
|
* The SEEQ8005 doesn't like us writing to its registers
|
|
* too quickly.
|
|
*/
|
|
static inline void ether3_outb(int v, const void __iomem *r)
|
|
{
|
|
writeb(v, r);
|
|
udelay(1);
|
|
}
|
|
|
|
static inline void ether3_outw(int v, const void __iomem *r)
|
|
{
|
|
writew(v, r);
|
|
udelay(1);
|
|
}
|
|
#define ether3_inb(r) ({ unsigned int __v = readb((r)); udelay(1); __v; })
|
|
#define ether3_inw(r) ({ unsigned int __v = readw((r)); udelay(1); __v; })
|
|
|
|
static int
|
|
ether3_setbuffer(struct net_device *dev, buffer_rw_t read, int start)
|
|
{
|
|
int timeout = 1000;
|
|
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_LOCBUFMEM, REG_CONFIG1);
|
|
ether3_outw(priv(dev)->regs.command | CMD_FIFOWRITE, REG_COMMAND);
|
|
|
|
while ((ether3_inw(REG_STATUS) & STAT_FIFOEMPTY) == 0) {
|
|
if (!timeout--) {
|
|
printk("%s: setbuffer broken\n", dev->name);
|
|
priv(dev)->broken = 1;
|
|
return 1;
|
|
}
|
|
udelay(1);
|
|
}
|
|
|
|
if (read == buffer_read) {
|
|
ether3_outw(start, REG_DMAADDR);
|
|
ether3_outw(priv(dev)->regs.command | CMD_FIFOREAD, REG_COMMAND);
|
|
} else {
|
|
ether3_outw(priv(dev)->regs.command | CMD_FIFOWRITE, REG_COMMAND);
|
|
ether3_outw(start, REG_DMAADDR);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* write data to the buffer memory
|
|
*/
|
|
#define ether3_writebuffer(dev,data,length) \
|
|
writesw(REG_BUFWIN, (data), (length) >> 1)
|
|
|
|
#define ether3_writeword(dev,data) \
|
|
writew((data), REG_BUFWIN)
|
|
|
|
#define ether3_writelong(dev,data) { \
|
|
void __iomem *reg_bufwin = REG_BUFWIN; \
|
|
writew((data), reg_bufwin); \
|
|
writew((data) >> 16, reg_bufwin); \
|
|
}
|
|
|
|
/*
|
|
* read data from the buffer memory
|
|
*/
|
|
#define ether3_readbuffer(dev,data,length) \
|
|
readsw(REG_BUFWIN, (data), (length) >> 1)
|
|
|
|
#define ether3_readword(dev) \
|
|
readw(REG_BUFWIN)
|
|
|
|
#define ether3_readlong(dev) \
|
|
readw(REG_BUFWIN) | (readw(REG_BUFWIN) << 16)
|
|
|
|
/*
|
|
* Switch LED off...
|
|
*/
|
|
static void ether3_ledoff(unsigned long data)
|
|
{
|
|
struct net_device *dev = (struct net_device *)data;
|
|
ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
|
|
}
|
|
|
|
/*
|
|
* switch LED on...
|
|
*/
|
|
static inline void ether3_ledon(struct net_device *dev)
|
|
{
|
|
del_timer(&priv(dev)->timer);
|
|
priv(dev)->timer.expires = jiffies + HZ / 50; /* leave on for 1/50th second */
|
|
priv(dev)->timer.data = (unsigned long)dev;
|
|
priv(dev)->timer.function = ether3_ledoff;
|
|
add_timer(&priv(dev)->timer);
|
|
if (priv(dev)->regs.config2 & CFG2_CTRLO)
|
|
ether3_outw(priv(dev)->regs.config2 &= ~CFG2_CTRLO, REG_CONFIG2);
|
|
}
|
|
|
|
/*
|
|
* Read the ethernet address string from the on board rom.
|
|
* This is an ascii string!!!
|
|
*/
|
|
static int __init
|
|
ether3_addr(char *addr, struct expansion_card *ec)
|
|
{
|
|
struct in_chunk_dir cd;
|
|
char *s;
|
|
|
|
if (ecard_readchunk(&cd, ec, 0xf5, 0) && (s = strchr(cd.d.string, '('))) {
|
|
int i;
|
|
for (i = 0; i<6; i++) {
|
|
addr[i] = simple_strtoul(s + 1, &s, 0x10);
|
|
if (*s != (i==5?')' : ':' ))
|
|
break;
|
|
}
|
|
if (i == 6)
|
|
return 0;
|
|
}
|
|
/* I wonder if we should even let the user continue in this case
|
|
* - no, it would be better to disable the device
|
|
*/
|
|
printk(KERN_ERR "ether3: Couldn't read a valid MAC address from card.\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------------- */
|
|
|
|
static int __init
|
|
ether3_ramtest(struct net_device *dev, unsigned char byte)
|
|
{
|
|
unsigned char *buffer = kmalloc(RX_END, GFP_KERNEL);
|
|
int i,ret = 0;
|
|
int max_errors = 4;
|
|
int bad = -1;
|
|
|
|
if (!buffer)
|
|
return 1;
|
|
|
|
memset(buffer, byte, RX_END);
|
|
ether3_setbuffer(dev, buffer_write, 0);
|
|
ether3_writebuffer(dev, buffer, TX_END);
|
|
ether3_setbuffer(dev, buffer_write, RX_START);
|
|
ether3_writebuffer(dev, buffer + RX_START, RX_LEN);
|
|
memset(buffer, byte ^ 0xff, RX_END);
|
|
ether3_setbuffer(dev, buffer_read, 0);
|
|
ether3_readbuffer(dev, buffer, TX_END);
|
|
ether3_setbuffer(dev, buffer_read, RX_START);
|
|
ether3_readbuffer(dev, buffer + RX_START, RX_LEN);
|
|
|
|
for (i = 0; i < RX_END; i++) {
|
|
if (buffer[i] != byte) {
|
|
if (max_errors > 0 && bad != buffer[i]) {
|
|
printk("%s: RAM failed with (%02X instead of %02X) at 0x%04X",
|
|
dev->name, buffer[i], byte, i);
|
|
ret = 2;
|
|
max_errors--;
|
|
bad = i;
|
|
}
|
|
} else {
|
|
if (bad != -1) {
|
|
if (bad != i - 1)
|
|
printk(" - 0x%04X\n", i - 1);
|
|
printk("\n");
|
|
bad = -1;
|
|
}
|
|
}
|
|
}
|
|
if (bad != -1)
|
|
printk(" - 0xffff\n");
|
|
kfree(buffer);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* ------------------------------------------------------------------------------- */
|
|
|
|
static int __init ether3_init_2(struct net_device *dev)
|
|
{
|
|
int i;
|
|
|
|
priv(dev)->regs.config1 = CFG1_RECVCOMPSTAT0|CFG1_DMABURST8;
|
|
priv(dev)->regs.config2 = CFG2_CTRLO|CFG2_RECVCRC|CFG2_ERRENCRC;
|
|
priv(dev)->regs.command = 0;
|
|
|
|
/*
|
|
* Set up our hardware address
|
|
*/
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_BUFSELSTAT0, REG_CONFIG1);
|
|
for (i = 0; i < 6; i++)
|
|
ether3_outb(dev->dev_addr[i], REG_BUFWIN);
|
|
|
|
if (dev->flags & IFF_PROMISC)
|
|
priv(dev)->regs.config1 |= CFG1_RECVPROMISC;
|
|
else if (dev->flags & IFF_MULTICAST)
|
|
priv(dev)->regs.config1 |= CFG1_RECVSPECBRMULTI;
|
|
else
|
|
priv(dev)->regs.config1 |= CFG1_RECVSPECBROAD;
|
|
|
|
/*
|
|
* There is a problem with the NQ8005 in that it occasionally loses the
|
|
* last two bytes. To get round this problem, we receive the CRC as
|
|
* well. That way, if we do lose the last two, then it doesn't matter.
|
|
*/
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_TRANSEND, REG_CONFIG1);
|
|
ether3_outw((TX_END>>8) - 1, REG_BUFWIN);
|
|
ether3_outw(priv(dev)->rx_head, REG_RECVPTR);
|
|
ether3_outw(0, REG_TRANSMITPTR);
|
|
ether3_outw(priv(dev)->rx_head >> 8, REG_RECVEND);
|
|
ether3_outw(priv(dev)->regs.config2, REG_CONFIG2);
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_LOCBUFMEM, REG_CONFIG1);
|
|
ether3_outw(priv(dev)->regs.command, REG_COMMAND);
|
|
|
|
i = ether3_ramtest(dev, 0x5A);
|
|
if(i)
|
|
return i;
|
|
i = ether3_ramtest(dev, 0x1E);
|
|
if(i)
|
|
return i;
|
|
|
|
ether3_setbuffer(dev, buffer_write, 0);
|
|
ether3_writelong(dev, 0);
|
|
return 0;
|
|
}
|
|
|
|
static void
|
|
ether3_init_for_open(struct net_device *dev)
|
|
{
|
|
int i;
|
|
|
|
memset(&priv(dev)->stats, 0, sizeof(struct net_device_stats));
|
|
|
|
/* Reset the chip */
|
|
ether3_outw(CFG2_RESET, REG_CONFIG2);
|
|
udelay(4);
|
|
|
|
priv(dev)->regs.command = 0;
|
|
ether3_outw(CMD_RXOFF|CMD_TXOFF, REG_COMMAND);
|
|
while (ether3_inw(REG_STATUS) & (STAT_RXON|STAT_TXON))
|
|
barrier();
|
|
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_BUFSELSTAT0, REG_CONFIG1);
|
|
for (i = 0; i < 6; i++)
|
|
ether3_outb(dev->dev_addr[i], REG_BUFWIN);
|
|
|
|
priv(dev)->tx_head = 0;
|
|
priv(dev)->tx_tail = 0;
|
|
priv(dev)->regs.config2 |= CFG2_CTRLO;
|
|
priv(dev)->rx_head = RX_START;
|
|
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_TRANSEND, REG_CONFIG1);
|
|
ether3_outw((TX_END>>8) - 1, REG_BUFWIN);
|
|
ether3_outw(priv(dev)->rx_head, REG_RECVPTR);
|
|
ether3_outw(priv(dev)->rx_head >> 8, REG_RECVEND);
|
|
ether3_outw(0, REG_TRANSMITPTR);
|
|
ether3_outw(priv(dev)->regs.config2, REG_CONFIG2);
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_LOCBUFMEM, REG_CONFIG1);
|
|
|
|
ether3_setbuffer(dev, buffer_write, 0);
|
|
ether3_writelong(dev, 0);
|
|
|
|
priv(dev)->regs.command = CMD_ENINTRX | CMD_ENINTTX;
|
|
ether3_outw(priv(dev)->regs.command | CMD_RXON, REG_COMMAND);
|
|
}
|
|
|
|
static inline int
|
|
ether3_probe_bus_8(struct net_device *dev, int val)
|
|
{
|
|
int write_low, write_high, read_low, read_high;
|
|
|
|
write_low = val & 255;
|
|
write_high = val >> 8;
|
|
|
|
printk(KERN_DEBUG "ether3_probe: write8 [%02X:%02X]", write_high, write_low);
|
|
|
|
ether3_outb(write_low, REG_RECVPTR);
|
|
ether3_outb(write_high, REG_RECVPTR + 4);
|
|
|
|
read_low = ether3_inb(REG_RECVPTR);
|
|
read_high = ether3_inb(REG_RECVPTR + 4);
|
|
|
|
printk(", read8 [%02X:%02X]\n", read_high, read_low);
|
|
|
|
return read_low == write_low && read_high == write_high;
|
|
}
|
|
|
|
static inline int
|
|
ether3_probe_bus_16(struct net_device *dev, int val)
|
|
{
|
|
int read_val;
|
|
|
|
ether3_outw(val, REG_RECVPTR);
|
|
read_val = ether3_inw(REG_RECVPTR);
|
|
|
|
printk(KERN_DEBUG "ether3_probe: write16 [%04X], read16 [%04X]\n", val, read_val);
|
|
|
|
return read_val == val;
|
|
}
|
|
|
|
/*
|
|
* Open/initialize the board. This is called (in the current kernel)
|
|
* sometime after booting when the 'ifconfig' program is run.
|
|
*
|
|
* This routine should set everything up anew at each open, even
|
|
* registers that "should" only need to be set once at boot, so that
|
|
* there is non-reboot way to recover if something goes wrong.
|
|
*/
|
|
static int
|
|
ether3_open(struct net_device *dev)
|
|
{
|
|
if (!is_valid_ether_addr(dev->dev_addr)) {
|
|
printk(KERN_WARNING "%s: invalid ethernet MAC address\n",
|
|
dev->name);
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (request_irq(dev->irq, ether3_interrupt, 0, "ether3", dev))
|
|
return -EAGAIN;
|
|
|
|
ether3_init_for_open(dev);
|
|
|
|
netif_start_queue(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* The inverse routine to ether3_open().
|
|
*/
|
|
static int
|
|
ether3_close(struct net_device *dev)
|
|
{
|
|
netif_stop_queue(dev);
|
|
|
|
disable_irq(dev->irq);
|
|
|
|
ether3_outw(CMD_RXOFF|CMD_TXOFF, REG_COMMAND);
|
|
priv(dev)->regs.command = 0;
|
|
while (ether3_inw(REG_STATUS) & (STAT_RXON|STAT_TXON))
|
|
barrier();
|
|
ether3_outb(0x80, REG_CONFIG2 + 4);
|
|
ether3_outw(0, REG_COMMAND);
|
|
|
|
free_irq(dev->irq, dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Get the current statistics. This may be called with the card open or
|
|
* closed.
|
|
*/
|
|
static struct net_device_stats *ether3_getstats(struct net_device *dev)
|
|
{
|
|
return &priv(dev)->stats;
|
|
}
|
|
|
|
/*
|
|
* Set or clear promiscuous/multicast mode filter for this adaptor.
|
|
*
|
|
* We don't attempt any packet filtering. The card may have a SEEQ 8004
|
|
* in which does not have the other ethernet address registers present...
|
|
*/
|
|
static void ether3_setmulticastlist(struct net_device *dev)
|
|
{
|
|
priv(dev)->regs.config1 &= ~CFG1_RECVPROMISC;
|
|
|
|
if (dev->flags & IFF_PROMISC) {
|
|
/* promiscuous mode */
|
|
priv(dev)->regs.config1 |= CFG1_RECVPROMISC;
|
|
} else if (dev->flags & IFF_ALLMULTI) {
|
|
priv(dev)->regs.config1 |= CFG1_RECVSPECBRMULTI;
|
|
} else
|
|
priv(dev)->regs.config1 |= CFG1_RECVSPECBROAD;
|
|
|
|
ether3_outw(priv(dev)->regs.config1 | CFG1_LOCBUFMEM, REG_CONFIG1);
|
|
}
|
|
|
|
static void ether3_timeout(struct net_device *dev)
|
|
{
|
|
unsigned long flags;
|
|
|
|
del_timer(&priv(dev)->timer);
|
|
|
|
local_irq_save(flags);
|
|
printk(KERN_ERR "%s: transmit timed out, network cable problem?\n", dev->name);
|
|
printk(KERN_ERR "%s: state: { status=%04X cfg1=%04X cfg2=%04X }\n", dev->name,
|
|
ether3_inw(REG_STATUS), ether3_inw(REG_CONFIG1), ether3_inw(REG_CONFIG2));
|
|
printk(KERN_ERR "%s: { rpr=%04X rea=%04X tpr=%04X }\n", dev->name,
|
|
ether3_inw(REG_RECVPTR), ether3_inw(REG_RECVEND), ether3_inw(REG_TRANSMITPTR));
|
|
printk(KERN_ERR "%s: tx head=%X tx tail=%X\n", dev->name,
|
|
priv(dev)->tx_head, priv(dev)->tx_tail);
|
|
ether3_setbuffer(dev, buffer_read, priv(dev)->tx_tail);
|
|
printk(KERN_ERR "%s: packet status = %08X\n", dev->name, ether3_readlong(dev));
|
|
local_irq_restore(flags);
|
|
|
|
priv(dev)->regs.config2 |= CFG2_CTRLO;
|
|
priv(dev)->stats.tx_errors += 1;
|
|
ether3_outw(priv(dev)->regs.config2, REG_CONFIG2);
|
|
priv(dev)->tx_head = priv(dev)->tx_tail = 0;
|
|
|
|
netif_wake_queue(dev);
|
|
}
|
|
|
|
/*
|
|
* Transmit a packet
|
|
*/
|
|
static int
|
|
ether3_sendpacket(struct sk_buff *skb, struct net_device *dev)
|
|
{
|
|
unsigned long flags;
|
|
unsigned int length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN;
|
|
unsigned int ptr, next_ptr;
|
|
|
|
if (priv(dev)->broken) {
|
|
dev_kfree_skb(skb);
|
|
priv(dev)->stats.tx_dropped ++;
|
|
netif_start_queue(dev);
|
|
return 0;
|
|
}
|
|
|
|
length = (length + 1) & ~1;
|
|
if (length != skb->len) {
|
|
if (skb_padto(skb, length))
|
|
goto out;
|
|
}
|
|
|
|
next_ptr = (priv(dev)->tx_head + 1) & 15;
|
|
|
|
local_irq_save(flags);
|
|
|
|
if (priv(dev)->tx_tail == next_ptr) {
|
|
local_irq_restore(flags);
|
|
return 1; /* unable to queue */
|
|
}
|
|
|
|
dev->trans_start = jiffies;
|
|
ptr = 0x600 * priv(dev)->tx_head;
|
|
priv(dev)->tx_head = next_ptr;
|
|
next_ptr *= 0x600;
|
|
|
|
#define TXHDR_FLAGS (TXHDR_TRANSMIT|TXHDR_CHAINCONTINUE|TXHDR_DATAFOLLOWS|TXHDR_ENSUCCESS)
|
|
|
|
ether3_setbuffer(dev, buffer_write, next_ptr);
|
|
ether3_writelong(dev, 0);
|
|
ether3_setbuffer(dev, buffer_write, ptr);
|
|
ether3_writelong(dev, 0);
|
|
ether3_writebuffer(dev, skb->data, length);
|
|
ether3_writeword(dev, htons(next_ptr));
|
|
ether3_writeword(dev, TXHDR_CHAINCONTINUE >> 16);
|
|
ether3_setbuffer(dev, buffer_write, ptr);
|
|
ether3_writeword(dev, htons((ptr + length + 4)));
|
|
ether3_writeword(dev, TXHDR_FLAGS >> 16);
|
|
ether3_ledon(dev);
|
|
|
|
if (!(ether3_inw(REG_STATUS) & STAT_TXON)) {
|
|
ether3_outw(ptr, REG_TRANSMITPTR);
|
|
ether3_outw(priv(dev)->regs.command | CMD_TXON, REG_COMMAND);
|
|
}
|
|
|
|
next_ptr = (priv(dev)->tx_head + 1) & 15;
|
|
local_irq_restore(flags);
|
|
|
|
dev_kfree_skb(skb);
|
|
|
|
if (priv(dev)->tx_tail == next_ptr)
|
|
netif_stop_queue(dev);
|
|
|
|
out:
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t
|
|
ether3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
|
|
{
|
|
struct net_device *dev = (struct net_device *)dev_id;
|
|
unsigned int status, handled = IRQ_NONE;
|
|
|
|
#if NET_DEBUG > 1
|
|
if(net_debug & DEBUG_INT)
|
|
printk("eth3irq: %d ", irq);
|
|
#endif
|
|
|
|
status = ether3_inw(REG_STATUS);
|
|
|
|
if (status & STAT_INTRX) {
|
|
ether3_outw(CMD_ACKINTRX | priv(dev)->regs.command, REG_COMMAND);
|
|
ether3_rx(dev, 12);
|
|
handled = IRQ_HANDLED;
|
|
}
|
|
|
|
if (status & STAT_INTTX) {
|
|
ether3_outw(CMD_ACKINTTX | priv(dev)->regs.command, REG_COMMAND);
|
|
ether3_tx(dev);
|
|
handled = IRQ_HANDLED;
|
|
}
|
|
|
|
#if NET_DEBUG > 1
|
|
if(net_debug & DEBUG_INT)
|
|
printk("done\n");
|
|
#endif
|
|
return handled;
|
|
}
|
|
|
|
/*
|
|
* If we have a good packet(s), get it/them out of the buffers.
|
|
*/
|
|
static int ether3_rx(struct net_device *dev, unsigned int maxcnt)
|
|
{
|
|
unsigned int next_ptr = priv(dev)->rx_head, received = 0;
|
|
|
|
ether3_ledon(dev);
|
|
|
|
do {
|
|
unsigned int this_ptr, status;
|
|
unsigned char addrs[16];
|
|
|
|
/*
|
|
* read the first 16 bytes from the buffer.
|
|
* This contains the status bytes etc and ethernet addresses,
|
|
* and we also check the source ethernet address to see if
|
|
* it originated from us.
|
|
*/
|
|
{
|
|
unsigned int temp_ptr;
|
|
ether3_setbuffer(dev, buffer_read, next_ptr);
|
|
temp_ptr = ether3_readword(dev);
|
|
status = ether3_readword(dev);
|
|
if ((status & (RXSTAT_DONE | RXHDR_CHAINCONTINUE | RXHDR_RECEIVE)) !=
|
|
(RXSTAT_DONE | RXHDR_CHAINCONTINUE) || !temp_ptr)
|
|
break;
|
|
|
|
this_ptr = next_ptr + 4;
|
|
next_ptr = ntohs(temp_ptr);
|
|
}
|
|
ether3_setbuffer(dev, buffer_read, this_ptr);
|
|
ether3_readbuffer(dev, addrs+2, 12);
|
|
|
|
if (next_ptr < RX_START || next_ptr >= RX_END) {
|
|
int i;
|
|
printk("%s: bad next pointer @%04X: ", dev->name, priv(dev)->rx_head);
|
|
printk("%02X %02X %02X %02X ", next_ptr >> 8, next_ptr & 255, status & 255, status >> 8);
|
|
for (i = 2; i < 14; i++)
|
|
printk("%02X ", addrs[i]);
|
|
printk("\n");
|
|
next_ptr = priv(dev)->rx_head;
|
|
break;
|
|
}
|
|
/*
|
|
* ignore our own packets...
|
|
*/
|
|
if (!(*(unsigned long *)&dev->dev_addr[0] ^ *(unsigned long *)&addrs[2+6]) &&
|
|
!(*(unsigned short *)&dev->dev_addr[4] ^ *(unsigned short *)&addrs[2+10])) {
|
|
maxcnt ++; /* compensate for loopedback packet */
|
|
ether3_outw(next_ptr >> 8, REG_RECVEND);
|
|
} else
|
|
if (!(status & (RXSTAT_OVERSIZE|RXSTAT_CRCERROR|RXSTAT_DRIBBLEERROR|RXSTAT_SHORTPACKET))) {
|
|
unsigned int length = next_ptr - this_ptr;
|
|
struct sk_buff *skb;
|
|
|
|
if (next_ptr <= this_ptr)
|
|
length += RX_END - RX_START;
|
|
|
|
skb = dev_alloc_skb(length + 2);
|
|
if (skb) {
|
|
unsigned char *buf;
|
|
|
|
skb->dev = dev;
|
|
skb_reserve(skb, 2);
|
|
buf = skb_put(skb, length);
|
|
ether3_readbuffer(dev, buf + 12, length - 12);
|
|
ether3_outw(next_ptr >> 8, REG_RECVEND);
|
|
*(unsigned short *)(buf + 0) = *(unsigned short *)(addrs + 2);
|
|
*(unsigned long *)(buf + 2) = *(unsigned long *)(addrs + 4);
|
|
*(unsigned long *)(buf + 6) = *(unsigned long *)(addrs + 8);
|
|
*(unsigned short *)(buf + 10) = *(unsigned short *)(addrs + 12);
|
|
skb->protocol = eth_type_trans(skb, dev);
|
|
netif_rx(skb);
|
|
received ++;
|
|
} else
|
|
goto dropping;
|
|
} else {
|
|
struct net_device_stats *stats = &priv(dev)->stats;
|
|
ether3_outw(next_ptr >> 8, REG_RECVEND);
|
|
if (status & RXSTAT_OVERSIZE) stats->rx_over_errors ++;
|
|
if (status & RXSTAT_CRCERROR) stats->rx_crc_errors ++;
|
|
if (status & RXSTAT_DRIBBLEERROR) stats->rx_fifo_errors ++;
|
|
if (status & RXSTAT_SHORTPACKET) stats->rx_length_errors ++;
|
|
stats->rx_errors++;
|
|
}
|
|
}
|
|
while (-- maxcnt);
|
|
|
|
done:
|
|
priv(dev)->stats.rx_packets += received;
|
|
priv(dev)->rx_head = next_ptr;
|
|
/*
|
|
* If rx went off line, then that means that the buffer may be full. We
|
|
* have dropped at least one packet.
|
|
*/
|
|
if (!(ether3_inw(REG_STATUS) & STAT_RXON)) {
|
|
priv(dev)->stats.rx_dropped ++;
|
|
ether3_outw(next_ptr, REG_RECVPTR);
|
|
ether3_outw(priv(dev)->regs.command | CMD_RXON, REG_COMMAND);
|
|
}
|
|
|
|
return maxcnt;
|
|
|
|
dropping:{
|
|
static unsigned long last_warned;
|
|
|
|
ether3_outw(next_ptr >> 8, REG_RECVEND);
|
|
/*
|
|
* Don't print this message too many times...
|
|
*/
|
|
if (time_after(jiffies, last_warned + 10 * HZ)) {
|
|
last_warned = jiffies;
|
|
printk("%s: memory squeeze, dropping packet.\n", dev->name);
|
|
}
|
|
priv(dev)->stats.rx_dropped ++;
|
|
goto done;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Update stats for the transmitted packet(s)
|
|
*/
|
|
static void ether3_tx(struct net_device *dev)
|
|
{
|
|
unsigned int tx_tail = priv(dev)->tx_tail;
|
|
int max_work = 14;
|
|
|
|
do {
|
|
unsigned long status;
|
|
|
|
/*
|
|
* Read the packet header
|
|
*/
|
|
ether3_setbuffer(dev, buffer_read, tx_tail * 0x600);
|
|
status = ether3_readlong(dev);
|
|
|
|
/*
|
|
* Check to see if this packet has been transmitted
|
|
*/
|
|
if ((status & (TXSTAT_DONE | TXHDR_TRANSMIT)) !=
|
|
(TXSTAT_DONE | TXHDR_TRANSMIT))
|
|
break;
|
|
|
|
/*
|
|
* Update errors
|
|
*/
|
|
if (!(status & (TXSTAT_BABBLED | TXSTAT_16COLLISIONS)))
|
|
priv(dev)->stats.tx_packets++;
|
|
else {
|
|
priv(dev)->stats.tx_errors ++;
|
|
if (status & TXSTAT_16COLLISIONS)
|
|
priv(dev)->stats.collisions += 16;
|
|
if (status & TXSTAT_BABBLED)
|
|
priv(dev)->stats.tx_fifo_errors ++;
|
|
}
|
|
|
|
tx_tail = (tx_tail + 1) & 15;
|
|
} while (--max_work);
|
|
|
|
if (priv(dev)->tx_tail != tx_tail) {
|
|
priv(dev)->tx_tail = tx_tail;
|
|
netif_wake_queue(dev);
|
|
}
|
|
}
|
|
|
|
static void __init ether3_banner(void)
|
|
{
|
|
static unsigned version_printed = 0;
|
|
|
|
if (net_debug && version_printed++ == 0)
|
|
printk(KERN_INFO "%s", version);
|
|
}
|
|
|
|
static int __devinit
|
|
ether3_probe(struct expansion_card *ec, const struct ecard_id *id)
|
|
{
|
|
const struct ether3_data *data = id->data;
|
|
struct net_device *dev;
|
|
int i, bus_type, ret;
|
|
|
|
ether3_banner();
|
|
|
|
ret = ecard_request_resources(ec);
|
|
if (ret)
|
|
goto out;
|
|
|
|
dev = alloc_etherdev(sizeof(struct dev_priv));
|
|
if (!dev) {
|
|
ret = -ENOMEM;
|
|
goto release;
|
|
}
|
|
|
|
SET_MODULE_OWNER(dev);
|
|
SET_NETDEV_DEV(dev, &ec->dev);
|
|
|
|
priv(dev)->base = ioremap(ecard_resource_start(ec, ECARD_RES_MEMC),
|
|
ecard_resource_len(ec, ECARD_RES_MEMC));
|
|
if (!priv(dev)->base) {
|
|
ret = -ENOMEM;
|
|
goto free;
|
|
}
|
|
|
|
ec->irqaddr = priv(dev)->base + data->base_offset;
|
|
ec->irqmask = 0xf0;
|
|
|
|
priv(dev)->seeq = priv(dev)->base + data->base_offset;
|
|
dev->irq = ec->irq;
|
|
|
|
ether3_addr(dev->dev_addr, ec);
|
|
|
|
init_timer(&priv(dev)->timer);
|
|
|
|
/* Reset card...
|
|
*/
|
|
ether3_outb(0x80, REG_CONFIG2 + 4);
|
|
bus_type = BUS_UNKNOWN;
|
|
udelay(4);
|
|
|
|
/* Test using Receive Pointer (16-bit register) to find out
|
|
* how the ether3 is connected to the bus...
|
|
*/
|
|
if (ether3_probe_bus_8(dev, 0x100) &&
|
|
ether3_probe_bus_8(dev, 0x201))
|
|
bus_type = BUS_8;
|
|
|
|
if (bus_type == BUS_UNKNOWN &&
|
|
ether3_probe_bus_16(dev, 0x101) &&
|
|
ether3_probe_bus_16(dev, 0x201))
|
|
bus_type = BUS_16;
|
|
|
|
switch (bus_type) {
|
|
case BUS_UNKNOWN:
|
|
printk(KERN_ERR "%s: unable to identify bus width\n", dev->name);
|
|
ret = -ENODEV;
|
|
goto free;
|
|
|
|
case BUS_8:
|
|
printk(KERN_ERR "%s: %s found, but is an unsupported "
|
|
"8-bit card\n", dev->name, data->name);
|
|
ret = -ENODEV;
|
|
goto free;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (ether3_init_2(dev)) {
|
|
ret = -ENODEV;
|
|
goto free;
|
|
}
|
|
|
|
dev->open = ether3_open;
|
|
dev->stop = ether3_close;
|
|
dev->hard_start_xmit = ether3_sendpacket;
|
|
dev->get_stats = ether3_getstats;
|
|
dev->set_multicast_list = ether3_setmulticastlist;
|
|
dev->tx_timeout = ether3_timeout;
|
|
dev->watchdog_timeo = 5 * HZ / 100;
|
|
|
|
ret = register_netdev(dev);
|
|
if (ret)
|
|
goto free;
|
|
|
|
printk("%s: %s in slot %d, ", dev->name, data->name, ec->slot_no);
|
|
for (i = 0; i < 6; i++)
|
|
printk("%2.2x%c", dev->dev_addr[i], i == 5 ? '\n' : ':');
|
|
|
|
ecard_set_drvdata(ec, dev);
|
|
return 0;
|
|
|
|
free:
|
|
if (priv(dev)->base)
|
|
iounmap(priv(dev)->base);
|
|
free_netdev(dev);
|
|
release:
|
|
ecard_release_resources(ec);
|
|
out:
|
|
return ret;
|
|
}
|
|
|
|
static void __devexit ether3_remove(struct expansion_card *ec)
|
|
{
|
|
struct net_device *dev = ecard_get_drvdata(ec);
|
|
|
|
ecard_set_drvdata(ec, NULL);
|
|
|
|
unregister_netdev(dev);
|
|
iounmap(priv(dev)->base);
|
|
free_netdev(dev);
|
|
ecard_release_resources(ec);
|
|
}
|
|
|
|
static struct ether3_data ether3 = {
|
|
.name = "ether3",
|
|
.base_offset = 0,
|
|
};
|
|
|
|
static struct ether3_data etherb = {
|
|
.name = "etherb",
|
|
.base_offset = 0x800,
|
|
};
|
|
|
|
static const struct ecard_id ether3_ids[] = {
|
|
{ MANU_ANT2, PROD_ANT_ETHER3, ðer3 },
|
|
{ MANU_ANT, PROD_ANT_ETHER3, ðer3 },
|
|
{ MANU_ANT, PROD_ANT_ETHERB, ðerb },
|
|
{ 0xffff, 0xffff }
|
|
};
|
|
|
|
static struct ecard_driver ether3_driver = {
|
|
.probe = ether3_probe,
|
|
.remove = __devexit_p(ether3_remove),
|
|
.id_table = ether3_ids,
|
|
.drv = {
|
|
.name = "ether3",
|
|
},
|
|
};
|
|
|
|
static int __init ether3_init(void)
|
|
{
|
|
return ecard_register_driver(ðer3_driver);
|
|
}
|
|
|
|
static void __exit ether3_exit(void)
|
|
{
|
|
ecard_remove_driver(ðer3_driver);
|
|
}
|
|
|
|
module_init(ether3_init);
|
|
module_exit(ether3_exit);
|
|
|
|
MODULE_LICENSE("GPL");
|