redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/drivers/regulator/bd718x7-regulator.c
Matti Vaittinen 9bcbabafa1
regulator: bd718x7: remove voltage change restriction from BD71847 LDOs 
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.

The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850.

The power-good detection for LDOs can still cause false alarms if
LDO voltage is changed upwards when LDO is enabled.

Allow LDO voltage changes and disabe the power-good monioring for
the duration of the LDO voltage change and enable it after LDO
voltage has stabilized. ROHM HW colleagues measured the safety
limit of 1000uS for guaranteeing the voltage has stabilized. Let's
use that for starters and add confiurable stabilization wait-time
later if needed.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200513143921.GA22143@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-14 18:26:11 +01:00

1409 lines
40 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
// Copyright (C) 2018 ROHM Semiconductors
// bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/mfd/rohm-bd718x7.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/of_regulator.h>
#include <linux/slab.h>
/*
* BUCK1/2/3/4
* BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
* 00: 10.00mV/usec 10mV 1uS
* 01: 5.00mV/usec 10mV 2uS
* 10: 2.50mV/usec 10mV 4uS
* 11: 1.25mV/usec 10mV 8uS
*/
static int bd718xx_buck1234_set_ramp_delay(struct regulator_dev *rdev,
int ramp_delay)
{
int id = rdev_get_id(rdev);
unsigned int ramp_value;
dev_dbg(&rdev->dev, "Buck[%d] Set Ramp = %d\n", id + 1,
ramp_delay);
switch (ramp_delay) {
case 1 ... 1250:
ramp_value = BUCK_RAMPRATE_1P25MV;
break;
case 1251 ... 2500:
ramp_value = BUCK_RAMPRATE_2P50MV;
break;
case 2501 ... 5000:
ramp_value = BUCK_RAMPRATE_5P00MV;
break;
case 5001 ... 10000:
ramp_value = BUCK_RAMPRATE_10P00MV;
break;
default:
ramp_value = BUCK_RAMPRATE_10P00MV;
dev_err(&rdev->dev,
"%s: ramp_delay: %d not supported, setting 10000mV//us\n",
rdev->desc->name, ramp_delay);
}
return regmap_update_bits(rdev->regmap, BD718XX_REG_BUCK1_CTRL + id,
BUCK_RAMPRATE_MASK, ramp_value << 6);
}
/*
* On BD71837 (not on BD71847, BD71850, ...)
* Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
* Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
* is changed. Hence we return -EBUSY for these if voltage is changed
* when BUCK/LDO is enabled.
*
* On BD71847, BD71850, ... The LDO voltage can be changed when LDO is
* enabled. But if voltage is increased the LDO power-good monitoring
* must be disabled for the duration of changing + 1mS to ensure voltage
* has reached the higher level before HW does next under voltage detection
* cycle.
*/
static int bd71837_set_voltage_sel_restricted(struct regulator_dev *rdev,
unsigned int sel)
{
if (regulator_is_enabled_regmap(rdev))
return -EBUSY;
return regulator_set_voltage_sel_regmap(rdev, sel);
}
static void voltage_change_done(struct regulator_dev *rdev, unsigned int sel,
unsigned int *mask)
{
int ret;
if (*mask) {
/*
* Let's allow scheduling as we use I2C anyways. We just need to
* guarantee minimum of 1ms sleep - it shouldn't matter if we
* exceed it due to the scheduling.
*/
msleep(1);
/*
* Note for next hacker. The PWRGOOD should not be masked on
* BD71847 so we will just unconditionally enable detection
* when voltage is set.
* If someone want's to disable PWRGOOD he must implement
* caching and restoring the old value here. I am not
* aware of such use-cases so for the sake of the simplicity
* we just always enable PWRGOOD here.
*/
ret = regmap_update_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
*mask, 0);
if (ret)
dev_err(&rdev->dev,
"Failed to re-enable voltage monitoring (%d)\n",
ret);
}
}
static int voltage_change_prepare(struct regulator_dev *rdev, unsigned int sel,
unsigned int *mask)
{
int ret;
*mask = 0;
if (regulator_is_enabled_regmap(rdev)) {
int now, new;
now = rdev->desc->ops->get_voltage_sel(rdev);
if (now < 0)
return now;
now = rdev->desc->ops->list_voltage(rdev, now);
if (now < 0)
return now;
new = rdev->desc->ops->list_voltage(rdev, sel);
if (new < 0)
return new;
/*
* If we increase LDO voltage when LDO is enabled we need to
* disable the power-good detection until voltage has reached
* the new level. According to HW colleagues the maximum time
* it takes is 1000us. I assume that on systems with light load
* this might be less - and we could probably use DT to give
* system specific delay value if performance matters.
*
* Well, knowing we use I2C here and can add scheduling delays
* I don't think it is worth the hassle and I just add fixed
* 1ms sleep here (and allow scheduling). If this turns out to
* be a problem we can change it to delay and make the delay
* time configurable.
*/
if (new > now) {
int ldo_offset = rdev->desc->id - BD718XX_LDO1;
*mask = BD718XX_LDO1_VRMON80 << ldo_offset;
ret = regmap_update_bits(rdev->regmap,
BD718XX_REG_MVRFLTMASK2,
*mask, *mask);
if (ret) {
dev_err(&rdev->dev,
"Failed to stop voltage monitoring\n");
return ret;
}
}
}
return 0;
}
static int bd718xx_set_voltage_sel_restricted(struct regulator_dev *rdev,
unsigned int sel)
{
int ret;
int mask;
ret = voltage_change_prepare(rdev, sel, &mask);
if (ret)
return ret;
ret = regulator_set_voltage_sel_regmap(rdev, sel);
voltage_change_done(rdev, sel, &mask);
return ret;
}
static int bd718xx_set_voltage_sel_pickable_restricted(
struct regulator_dev *rdev, unsigned int sel)
{
int ret;
int mask;
ret = voltage_change_prepare(rdev, sel, &mask);
if (ret)
return ret;
ret = regulator_set_voltage_sel_pickable_regmap(rdev, sel);
voltage_change_done(rdev, sel, &mask);
return ret;
}
static int bd71837_set_voltage_sel_pickable_restricted(
struct regulator_dev *rdev, unsigned int sel)
{
if (regulator_is_enabled_regmap(rdev))
return -EBUSY;
return regulator_set_voltage_sel_pickable_regmap(rdev, sel);
}
static const struct regulator_ops bd718xx_pickable_range_ldo_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_pickable_linear_range,
.set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted,
.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
};
static const struct regulator_ops bd71837_pickable_range_ldo_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_pickable_linear_range,
.set_voltage_sel = bd71837_set_voltage_sel_pickable_restricted,
.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
};
static const struct regulator_ops bd718xx_pickable_range_buck_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_pickable_linear_range,
.set_voltage_sel = regulator_set_voltage_sel_pickable_regmap,
.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd71837_pickable_range_buck_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_pickable_linear_range,
.set_voltage_sel = bd71837_set_voltage_sel_pickable_restricted,
.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd71837_ldo_regulator_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
};
static const struct regulator_ops bd718xx_ldo_regulator_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
};
static const struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_table,
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
};
static const struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_table,
.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
};
static const struct regulator_ops bd718xx_buck_regulator_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd71837_buck_regulator_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.set_voltage_sel = bd71837_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_table,
.map_voltage = regulator_map_voltage_ascend,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_table,
.map_voltage = regulator_map_voltage_ascend,
.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
};
static const struct regulator_ops bd718xx_dvs_buck_regulator_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
.set_ramp_delay = bd718xx_buck1234_set_ramp_delay,
};
/*
* BD71837 BUCK1/2/3/4
* BD71847 BUCK1/2
* 0.70 to 1.30V (10mV step)
*/
static const struct linear_range bd718xx_dvs_buck_volts[] = {
REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
};
/*
* BD71837 BUCK5
* 0.7V to 1.35V (range 0)
* and
* 0.675 to 1.325 (range 1)
*/
static const struct linear_range bd71837_buck5_volts[] = {
/* Ranges when VOLT_SEL bit is 0 */
REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
/* Ranges when VOLT_SEL bit is 1 */
REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
};
/*
* Range selector for first 3 linear ranges is 0x0
* and 0x1 for last 3 ranges.
*/
static const unsigned int bd71837_buck5_volt_range_sel[] = {
0x0, 0x0, 0x0, 0x80, 0x80, 0x80
};
/*
* BD71847 BUCK3
*/
static const struct linear_range bd71847_buck3_volts[] = {
/* Ranges when VOLT_SEL bits are 00 */
REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
/* Ranges when VOLT_SEL bits are 01 */
REGULATOR_LINEAR_RANGE(550000, 0x0, 0x7, 50000),
/* Ranges when VOLT_SEL bits are 11 */
REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
};
static const unsigned int bd71847_buck3_volt_range_sel[] = {
0x0, 0x0, 0x0, 0x40, 0x80, 0x80, 0x80
};
static const struct linear_range bd71847_buck4_volts[] = {
REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
REGULATOR_LINEAR_RANGE(2600000, 0x00, 0x03, 100000),
};
static const unsigned int bd71847_buck4_volt_range_sel[] = { 0x0, 0x40 };
/*
* BUCK6
* 3.0V to 3.3V (step 100mV)
*/
static const struct linear_range bd71837_buck6_volts[] = {
REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
};
/*
* BD71837 BUCK7
* BD71847 BUCK5
* 000 = 1.605V
* 001 = 1.695V
* 010 = 1.755V
* 011 = 1.8V (Initial)
* 100 = 1.845V
* 101 = 1.905V
* 110 = 1.95V
* 111 = 1.995V
*/
static const unsigned int bd718xx_3rd_nodvs_buck_volts[] = {
1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
};
/*
* BUCK8
* 0.8V to 1.40V (step 10mV)
*/
static const struct linear_range bd718xx_4th_nodvs_buck_volts[] = {
REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
};
/*
* LDO1
* 3.0 to 3.3V (100mV step)
*/
static const struct linear_range bd718xx_ldo1_volts[] = {
REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000),
};
static const unsigned int bd718xx_ldo1_volt_range_sel[] = { 0x0, 0x20 };
/*
* LDO2
* 0.8 or 0.9V
*/
static const unsigned int ldo_2_volts[] = {
900000, 800000
};
/*
* LDO3
* 1.8 to 3.3V (100mV step)
*/
static const struct linear_range bd718xx_ldo3_volts[] = {
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};
/*
* LDO4
* 0.9 to 1.8V (100mV step)
*/
static const struct linear_range bd718xx_ldo4_volts[] = {
REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
};
/*
* LDO5 for BD71837
* 1.8 to 3.3V (100mV step)
*/
static const struct linear_range bd71837_ldo5_volts[] = {
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};
/*
* LDO5 for BD71837
* 1.8 to 3.3V (100mV step)
*/
static const struct linear_range bd71847_ldo5_volts[] = {
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
REGULATOR_LINEAR_RANGE(800000, 0x00, 0x0F, 100000),
};
static const unsigned int bd71847_ldo5_volt_range_sel[] = { 0x0, 0x20 };
/*
* LDO6
* 0.9 to 1.8V (100mV step)
*/
static const struct linear_range bd718xx_ldo6_volts[] = {
REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
};
/*
* LDO7
* 1.8 to 3.3V (100mV step)
*/
static const struct linear_range bd71837_ldo7_volts[] = {
REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};
struct reg_init {
unsigned int reg;
unsigned int mask;
unsigned int val;
};
struct bd718xx_regulator_data {
struct regulator_desc desc;
const struct rohm_dvs_config dvs;
const struct reg_init init;
const struct reg_init *additional_inits;
int additional_init_amnt;
};
/*
* There is a HW quirk in BD71837. The shutdown sequence timings for
* bucks/LDOs which are controlled via register interface are changed.
* At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
* beginning of shut-down sequence. As bucks 6 and 7 are parent
* supplies for LDO5 and LDO6 - this causes LDO5/6 voltage
* monitoring to errorneously detect under voltage and force PMIC to
* emergency state instead of poweroff. In order to avoid this we
* disable voltage monitoring for LDO5 and LDO6
*/
static const struct reg_init bd71837_ldo5_inits[] = {
{
.reg = BD718XX_REG_MVRFLTMASK2,
.mask = BD718XX_LDO5_VRMON80,
.val = BD718XX_LDO5_VRMON80,
},
};
static const struct reg_init bd71837_ldo6_inits[] = {
{
.reg = BD718XX_REG_MVRFLTMASK2,
.mask = BD718XX_LDO6_VRMON80,
.val = BD718XX_LDO6_VRMON80,
},
};
static int buck_set_hw_dvs_levels(struct device_node *np,
const struct regulator_desc *desc,
struct regulator_config *cfg)
{
struct bd718xx_regulator_data *data;
data = container_of(desc, struct bd718xx_regulator_data, desc);
return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
}
static const struct bd718xx_regulator_data bd71847_regulators[] = {
{
.desc = {
.name = "buck1",
.of_match = of_match_ptr("BUCK1"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK1,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges =
ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK1_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
ROHM_DVS_LEVEL_SUSPEND,
.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
.idle_mask = DVS_BUCK_RUN_MASK,
.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
.suspend_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD718XX_REG_BUCK1_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck2",
.of_match = of_match_ptr("BUCK2"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK2,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK2_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
.idle_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD718XX_REG_BUCK2_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck3",
.of_match = of_match_ptr("BUCK3"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK3,
.ops = &bd718xx_pickable_range_buck_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71847_BUCK3_VOLTAGE_NUM,
.linear_ranges = bd71847_buck3_volts,
.n_linear_ranges =
ARRAY_SIZE(bd71847_buck3_volts),
.vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
.vsel_mask = BD718XX_1ST_NODVS_BUCK_MASK,
.vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
.vsel_range_mask = BD71847_BUCK3_RANGE_MASK,
.linear_range_selectors = bd71847_buck3_volt_range_sel,
.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck4",
.of_match = of_match_ptr("BUCK4"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK4,
.ops = &bd718xx_pickable_range_buck_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71847_BUCK4_VOLTAGE_NUM,
.linear_ranges = bd71847_buck4_volts,
.n_linear_ranges =
ARRAY_SIZE(bd71847_buck4_volts),
.enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
.vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
.vsel_mask = BD71847_BUCK4_MASK,
.vsel_range_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
.vsel_range_mask = BD71847_BUCK4_RANGE_MASK,
.linear_range_selectors = bd71847_buck4_volt_range_sel,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck5",
.of_match = of_match_ptr("BUCK5"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK5,
.ops = &bd718xx_buck_regulator_nolinear_ops,
.type = REGULATOR_VOLTAGE,
.volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
.n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
.vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck6",
.of_match = of_match_ptr("BUCK6"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK6,
.ops = &bd718xx_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_4th_nodvs_buck_volts,
.n_linear_ranges =
ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
.vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "ldo1",
.of_match = of_match_ptr("LDO1"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO1,
.ops = &bd718xx_pickable_range_ldo_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo1_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
.vsel_reg = BD718XX_REG_LDO1_VOLT,
.vsel_mask = BD718XX_LDO1_MASK,
.vsel_range_reg = BD718XX_REG_LDO1_VOLT,
.vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
.enable_reg = BD718XX_REG_LDO1_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO1_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo2",
.of_match = of_match_ptr("LDO2"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO2,
.ops = &bd718xx_ldo_regulator_nolinear_ops,
.type = REGULATOR_VOLTAGE,
.volt_table = &ldo_2_volts[0],
.vsel_reg = BD718XX_REG_LDO2_VOLT,
.vsel_mask = BD718XX_LDO2_MASK,
.n_voltages = ARRAY_SIZE(ldo_2_volts),
.enable_reg = BD718XX_REG_LDO2_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO2_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo3",
.of_match = of_match_ptr("LDO3"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO3,
.ops = &bd718xx_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo3_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
.vsel_reg = BD718XX_REG_LDO3_VOLT,
.vsel_mask = BD718XX_LDO3_MASK,
.enable_reg = BD718XX_REG_LDO3_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO3_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo4",
.of_match = of_match_ptr("LDO4"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO4,
.ops = &bd718xx_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo4_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
.vsel_reg = BD718XX_REG_LDO4_VOLT,
.vsel_mask = BD718XX_LDO4_MASK,
.enable_reg = BD718XX_REG_LDO4_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO4_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo5",
.of_match = of_match_ptr("LDO5"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO5,
.ops = &bd718xx_pickable_range_ldo_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71847_LDO5_VOLTAGE_NUM,
.linear_ranges = bd71847_ldo5_volts,
.n_linear_ranges = ARRAY_SIZE(bd71847_ldo5_volts),
.vsel_reg = BD718XX_REG_LDO5_VOLT,
.vsel_mask = BD71847_LDO5_MASK,
.vsel_range_reg = BD718XX_REG_LDO5_VOLT,
.vsel_range_mask = BD71847_LDO5_RANGE_MASK,
.linear_range_selectors = bd71847_ldo5_volt_range_sel,
.enable_reg = BD718XX_REG_LDO5_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO5_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo6",
.of_match = of_match_ptr("LDO6"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO6,
.ops = &bd718xx_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo6_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
/* LDO6 is supplied by buck5 */
.supply_name = "buck5",
.vsel_reg = BD718XX_REG_LDO6_VOLT,
.vsel_mask = BD718XX_LDO6_MASK,
.enable_reg = BD718XX_REG_LDO6_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO6_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
};
static const struct bd718xx_regulator_data bd71837_regulators[] = {
{
.desc = {
.name = "buck1",
.of_match = of_match_ptr("BUCK1"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK1,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK1_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
ROHM_DVS_LEVEL_SUSPEND,
.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
.idle_mask = DVS_BUCK_RUN_MASK,
.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
.suspend_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD718XX_REG_BUCK1_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck2",
.of_match = of_match_ptr("BUCK2"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK2,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD718XX_REG_BUCK2_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
.idle_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD718XX_REG_BUCK2_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck3",
.of_match = of_match_ptr("BUCK3"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK3,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD71837_REG_BUCK3_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN,
.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD71837_REG_BUCK3_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck4",
.of_match = of_match_ptr("BUCK4"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK4,
.ops = &bd718xx_dvs_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_dvs_buck_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
.vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
.vsel_mask = DVS_BUCK_RUN_MASK,
.enable_reg = BD71837_REG_BUCK4_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
.of_parse_cb = buck_set_hw_dvs_levels,
},
.dvs = {
.level_map = ROHM_DVS_LEVEL_RUN,
.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
.run_mask = DVS_BUCK_RUN_MASK,
},
.init = {
.reg = BD71837_REG_BUCK4_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck5",
.of_match = of_match_ptr("BUCK5"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK5,
.ops = &bd71837_pickable_range_buck_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
.linear_ranges = bd71837_buck5_volts,
.n_linear_ranges =
ARRAY_SIZE(bd71837_buck5_volts),
.vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
.vsel_mask = BD71837_BUCK5_MASK,
.vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
.vsel_range_mask = BD71837_BUCK5_RANGE_MASK,
.linear_range_selectors = bd71837_buck5_volt_range_sel,
.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck6",
.of_match = of_match_ptr("BUCK6"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK6,
.ops = &bd71837_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
.linear_ranges = bd71837_buck6_volts,
.n_linear_ranges =
ARRAY_SIZE(bd71837_buck6_volts),
.vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
.vsel_mask = BD71837_BUCK6_MASK,
.enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck7",
.of_match = of_match_ptr("BUCK7"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK7,
.ops = &bd71837_buck_regulator_nolinear_ops,
.type = REGULATOR_VOLTAGE,
.volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
.n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
.vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "buck8",
.of_match = of_match_ptr("BUCK8"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_BUCK8,
.ops = &bd71837_buck_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
.linear_ranges = bd718xx_4th_nodvs_buck_volts,
.n_linear_ranges =
ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
.vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.enable_mask = BD718XX_BUCK_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
.mask = BD718XX_BUCK_SEL,
.val = BD718XX_BUCK_SEL,
},
},
{
.desc = {
.name = "ldo1",
.of_match = of_match_ptr("LDO1"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO1,
.ops = &bd71837_pickable_range_ldo_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo1_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
.vsel_reg = BD718XX_REG_LDO1_VOLT,
.vsel_mask = BD718XX_LDO1_MASK,
.vsel_range_reg = BD718XX_REG_LDO1_VOLT,
.vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
.enable_reg = BD718XX_REG_LDO1_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO1_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo2",
.of_match = of_match_ptr("LDO2"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO2,
.ops = &bd71837_ldo_regulator_nolinear_ops,
.type = REGULATOR_VOLTAGE,
.volt_table = &ldo_2_volts[0],
.vsel_reg = BD718XX_REG_LDO2_VOLT,
.vsel_mask = BD718XX_LDO2_MASK,
.n_voltages = ARRAY_SIZE(ldo_2_volts),
.enable_reg = BD718XX_REG_LDO2_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO2_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo3",
.of_match = of_match_ptr("LDO3"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO3,
.ops = &bd71837_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo3_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
.vsel_reg = BD718XX_REG_LDO3_VOLT,
.vsel_mask = BD718XX_LDO3_MASK,
.enable_reg = BD718XX_REG_LDO3_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO3_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo4",
.of_match = of_match_ptr("LDO4"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO4,
.ops = &bd71837_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo4_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
.vsel_reg = BD718XX_REG_LDO4_VOLT,
.vsel_mask = BD718XX_LDO4_MASK,
.enable_reg = BD718XX_REG_LDO4_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO4_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
{
.desc = {
.name = "ldo5",
.of_match = of_match_ptr("LDO5"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO5,
.ops = &bd71837_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71837_LDO5_VOLTAGE_NUM,
.linear_ranges = bd71837_ldo5_volts,
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_volts),
/* LDO5 is supplied by buck6 */
.supply_name = "buck6",
.vsel_reg = BD718XX_REG_LDO5_VOLT,
.vsel_mask = BD71837_LDO5_MASK,
.enable_reg = BD718XX_REG_LDO5_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO5_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
.additional_inits = bd71837_ldo5_inits,
.additional_init_amnt = ARRAY_SIZE(bd71837_ldo5_inits),
},
{
.desc = {
.name = "ldo6",
.of_match = of_match_ptr("LDO6"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO6,
.ops = &bd71837_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
.linear_ranges = bd718xx_ldo6_volts,
.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
/* LDO6 is supplied by buck7 */
.supply_name = "buck7",
.vsel_reg = BD718XX_REG_LDO6_VOLT,
.vsel_mask = BD718XX_LDO6_MASK,
.enable_reg = BD718XX_REG_LDO6_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD718XX_REG_LDO6_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
.additional_inits = bd71837_ldo6_inits,
.additional_init_amnt = ARRAY_SIZE(bd71837_ldo6_inits),
},
{
.desc = {
.name = "ldo7",
.of_match = of_match_ptr("LDO7"),
.regulators_node = of_match_ptr("regulators"),
.id = BD718XX_LDO7,
.ops = &bd71837_ldo_regulator_ops,
.type = REGULATOR_VOLTAGE,
.n_voltages = BD71837_LDO7_VOLTAGE_NUM,
.linear_ranges = bd71837_ldo7_volts,
.n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_volts),
.vsel_reg = BD71837_REG_LDO7_VOLT,
.vsel_mask = BD71837_LDO7_MASK,
.enable_reg = BD71837_REG_LDO7_VOLT,
.enable_mask = BD718XX_LDO_EN,
.owner = THIS_MODULE,
},
.init = {
.reg = BD71837_REG_LDO7_VOLT,
.mask = BD718XX_LDO_SEL,
.val = BD718XX_LDO_SEL,
},
},
};
static int bd718xx_probe(struct platform_device *pdev)
{
struct bd718xx *mfd;
struct regulator_config config = { 0 };
int i, j, err;
bool use_snvs;
const struct bd718xx_regulator_data *reg_data;
unsigned int num_reg_data;
enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
mfd = dev_get_drvdata(pdev->dev.parent);
if (!mfd) {
dev_err(&pdev->dev, "No MFD driver data\n");
err = -EINVAL;
goto err;
}
switch (chip) {
case ROHM_CHIP_TYPE_BD71837:
reg_data = bd71837_regulators;
num_reg_data = ARRAY_SIZE(bd71837_regulators);
break;
case ROHM_CHIP_TYPE_BD71847:
reg_data = bd71847_regulators;
num_reg_data = ARRAY_SIZE(bd71847_regulators);
break;
default:
dev_err(&pdev->dev, "Unsupported chip type\n");
err = -EINVAL;
goto err;
}
/* Register LOCK release */
err = regmap_update_bits(mfd->chip.regmap, BD718XX_REG_REGLOCK,
(REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
if (err) {
dev_err(&pdev->dev, "Failed to unlock PMIC (%d)\n", err);
goto err;
} else {
dev_dbg(&pdev->dev, "Unlocked lock register 0x%x\n",
BD718XX_REG_REGLOCK);
}
use_snvs = of_property_read_bool(pdev->dev.parent->of_node,
"rohm,reset-snvs-powered");
/*
* Change the next stage from poweroff to be READY instead of SNVS
* for all reset types because OTP loading at READY will clear SEL
* bit allowing HW defaults for power rails to be used
*/
if (!use_snvs) {
err = regmap_update_bits(mfd->chip.regmap,
BD718XX_REG_TRANS_COND1,
BD718XX_ON_REQ_POWEROFF_MASK |
BD718XX_SWRESET_POWEROFF_MASK |
BD718XX_WDOG_POWEROFF_MASK |
BD718XX_KEY_L_POWEROFF_MASK,
BD718XX_POWOFF_TO_RDY);
if (err) {
dev_err(&pdev->dev, "Failed to change reset target\n");
goto err;
} else {
dev_dbg(&pdev->dev,
"Changed all resets from SVNS to READY\n");
}
}
for (i = 0; i < num_reg_data; i++) {
const struct regulator_desc *desc;
struct regulator_dev *rdev;
const struct bd718xx_regulator_data *r;
r = &reg_data[i];
desc = &r->desc;
config.dev = pdev->dev.parent;
config.regmap = mfd->chip.regmap;
rdev = devm_regulator_register(&pdev->dev, desc, &config);
if (IS_ERR(rdev)) {
dev_err(&pdev->dev,
"failed to register %s regulator\n",
desc->name);
err = PTR_ERR(rdev);
goto err;
}
/*
* Regulator register gets the regulator constraints and
* applies them (set_machine_constraints). This should have
* turned the control register(s) to correct values and we
* can now switch the control from PMIC state machine to the
* register interface
*
* At poweroff transition PMIC HW disables EN bit for
* regulators but leaves SEL bit untouched. So if state
* transition from POWEROFF is done to SNVS - then all power
* rails controlled by SW (having SEL bit set) stay disabled
* as EN is cleared. This will result boot failure if any
* crucial systems are powered by these rails. We don't
* enable SW control for crucial regulators if snvs state is
* used
*/
if (!use_snvs || !rdev->constraints->always_on ||
!rdev->constraints->boot_on) {
err = regmap_update_bits(mfd->chip.regmap, r->init.reg,
r->init.mask, r->init.val);
if (err) {
dev_err(&pdev->dev,
"Failed to take control for (%s)\n",
desc->name);
goto err;
}
}
for (j = 0; j < r->additional_init_amnt; j++) {
err = regmap_update_bits(mfd->chip.regmap,
r->additional_inits[j].reg,
r->additional_inits[j].mask,
r->additional_inits[j].val);
if (err) {
dev_err(&pdev->dev,
"Buck (%s) initialization failed\n",
desc->name);
goto err;
}
}
}
err:
return err;
}
static const struct platform_device_id bd718x7_pmic_id[] = {
{ "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 },
{ "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 },
{ },
};
MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id);
static struct platform_driver bd718xx_regulator = {
.driver = {
.name = "bd718xx-pmic",
},
.probe = bd718xx_probe,
.id_table = bd718x7_pmic_id,
};
module_platform_driver(bd718xx_regulator);
MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
MODULE_DESCRIPTION("BD71837/BD71847 voltage regulator driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:bd718xx-pmic");
View git blame Copy permalink