alistair23-linux/drivers/usb
Greg KH 44f4c3ed60 USB: xhci: Set change bit when warm reset change is set.
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive".  This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.

When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd.  However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.

After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits.  (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted.  Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.

A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up.  That more
complicated fix will be merged next window, and this fix will be
backported to stable.

This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf3 ("xHCI: warm reset support").

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19 17:15:46 -07:00
..
atm drivers: usb: atm: ueagle-atm: Add missing const qualifier 2011-07-08 14:51:30 -07:00
c67x00
class USB: assign instead of equal in usbtmc.c 2011-08-08 12:34:45 -07:00
core USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth. 2011-08-15 09:22:40 -07:00
early
gadget Merge branch 'fixes' into for-greg 2011-08-15 19:02:25 +03:00
host USB: xhci: Set change bit when warm reset change is set. 2011-09-19 17:15:46 -07:00
image atomic: use <linux/atomic.h> 2011-07-26 16:49:47 -07:00
misc atomic: use <linux/atomic.h> 2011-07-26 16:49:47 -07:00
mon USB: mon: Allow to use usbmon without debugfs 2011-07-08 14:55:09 -07:00
musb usb: musb: gadget: fix error path 2011-08-12 12:06:34 +03:00
otg Merge branch 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6 2011-07-25 23:08:32 -07:00
renesas_usbhs usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h 2011-08-12 11:52:48 +03:00
serial USB: ftdi_sio: add Calao reference board support 2011-08-25 09:44:50 -07:00
storage USB: usb-storage: unusual_devs entry for ARM V2M motherboard. 2011-08-08 12:34:46 -07:00
wusbcore atomic: use <linux/atomic.h> 2011-07-26 16:49:47 -07:00
Kconfig usb: renesas_usbhs: compile/config are rescued 2011-07-08 14:57:12 -07:00
Makefile
README
usb-skeleton.c

To understand all the Linux-USB framework, you'll use these resources:

    * This source code.  This is necessarily an evolving work, and
      includes kerneldoc that should help you get a current overview.
      ("make pdfdocs", and then look at "usb.pdf" for host side and
      "gadget.pdf" for peripheral side.)  Also, Documentation/usb has
      more information.

    * The USB 2.0 specification (from www.usb.org), with supplements
      such as those for USB OTG and the various device classes.
      The USB specification has a good overview chapter, and USB
      peripherals conform to the widely known "Chapter 9".

    * Chip specifications for USB controllers.  Examples include
      host controllers (on PCs, servers, and more); peripheral
      controllers (in devices with Linux firmware, like printers or
      cell phones); and hard-wired peripherals like Ethernet adapters.

    * Specifications for other protocols implemented by USB peripheral
      functions.  Some are vendor-specific; others are vendor-neutral
      but just standardized outside of the www.usb.org team.

Here is a list of what each subdirectory here is, and what is contained in
them.

core/		- This is for the core USB host code, including the
		  usbfs files and the hub class driver ("khubd").

host/		- This is for USB host controller drivers.  This
		  includes UHCI, OHCI, EHCI, and others that might
		  be used with more specialized "embedded" systems.

gadget/		- This is for USB peripheral controller drivers and
		  the various gadget drivers which talk to them.


Individual USB driver directories.  A new driver should be added to the
first subdirectory in the list below that it fits into.

image/		- This is for still image drivers, like scanners or
		  digital cameras.
../input/	- This is for any driver that uses the input subsystem,
		  like keyboard, mice, touchscreens, tablets, etc.
../media/	- This is for multimedia drivers, like video cameras,
		  radios, and any other drivers that talk to the v4l
		  subsystem.
../net/		- This is for network drivers.
serial/		- This is for USB to serial drivers.
storage/	- This is for USB mass-storage drivers.
class/		- This is for all USB device drivers that do not fit
		  into any of the above categories, and work for a range
		  of USB Class specified devices. 
misc/		- This is for all USB device drivers that do not fit
		  into any of the above categories.