ee279588ac
The SNVS power key depends on board design, by default it should be disabled in SoC DT and ONLY be enabled on board DT if it is wired up. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
160 lines
3 KiB
Plaintext
160 lines
3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
//
|
|
// Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
|
|
#include "imx6sx-sdb.dtsi"
|
|
|
|
/ {
|
|
model = "Freescale i.MX6 SoloX SDB RevB Board";
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
|
status = "okay";
|
|
|
|
pmic: pfuze100@8 {
|
|
compatible = "fsl,pfuze200";
|
|
reg = <0x08>;
|
|
|
|
regulators {
|
|
sw1a_reg: sw1ab {
|
|
regulator-min-microvolt = <300000>;
|
|
regulator-max-microvolt = <1875000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <6250>;
|
|
};
|
|
|
|
sw2_reg: sw2 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
sw3a_reg: sw3a {
|
|
regulator-min-microvolt = <400000>;
|
|
regulator-max-microvolt = <1975000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
sw3b_reg: sw3b {
|
|
regulator-min-microvolt = <400000>;
|
|
regulator-max-microvolt = <1975000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
swbst_reg: swbst {
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5150000>;
|
|
};
|
|
|
|
snvs_reg: vsnvs {
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vref_reg: vrefddr {
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen1_reg: vgen1 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1550000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen2_reg: vgen2 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1550000>;
|
|
};
|
|
|
|
vgen3_reg: vgen3 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen4_reg: vgen4 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen5_reg: vgen5 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen6_reg: vgen6 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&qspi2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_qspi2>;
|
|
status = "okay";
|
|
|
|
flash0: n25q256a@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "micron,n25q256a", "jedec,spi-nor";
|
|
spi-max-frequency = <29000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <4>;
|
|
reg = <0>;
|
|
};
|
|
|
|
flash1: n25q256a@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "micron,n25q256a", "jedec,spi-nor";
|
|
spi-max-frequency = <29000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <4>;
|
|
reg = <2>;
|
|
};
|
|
};
|
|
|
|
®_arm {
|
|
vin-supply = <&sw1a_reg>;
|
|
};
|
|
|
|
®_soc {
|
|
vin-supply = <&sw1a_reg>;
|
|
};
|
|
|
|
®_vdd1p1 {
|
|
vin-supply = <&vgen6_reg>;
|
|
};
|
|
|
|
®_vdd3p0 {
|
|
vin-supply = <&sw2_reg>;
|
|
};
|
|
|
|
®_vdd2p5 {
|
|
vin-supply = <&vgen6_reg>;
|
|
};
|
|
|
|
®_can_stby {
|
|
/* Transceiver EN/STBY is active low on RevB board */
|
|
gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&snvs_pwrkey {
|
|
status = "okay";
|
|
};
|