6bad4f2ddb
The default settings used on the baseboard are good for the OMAP3530 and are compatible with the DM3730. However, the DM3730 has a faster L3 clock which means the camera pixel clock can also be pushed faster as well. This patch increase the Pixel clock to 90MHz which is the maximum the current ISP driver permits for an L3 clock of 200MHz. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
88 lines
2.6 KiB
Plaintext
88 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/dts-v1/;
|
|
|
|
#include "omap36xx.dtsi"
|
|
#include "logicpd-torpedo-som.dtsi"
|
|
#include "omap-gpmc-smsc9221.dtsi"
|
|
#include "logicpd-torpedo-baseboard.dtsi"
|
|
|
|
/ {
|
|
model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit";
|
|
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3";
|
|
|
|
wl12xx_vmmc: wl12xx_vmmc {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vwl1271";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
gpio = <&gpio5 29 0>; /* gpio157 */
|
|
startup-delay-us = <70000>;
|
|
enable-active-high;
|
|
vin-supply = <&vmmc2>;
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Only found on the wireless SOM. For the SOM without wireless, the pins for
|
|
* MMC3 can be routed with jumpers to the second MMC slot on the devkit and
|
|
* gpio157 is not connected. So this should be OK to keep common for now,
|
|
* probably device tree overlays is the way to go with the various SOM and
|
|
* jumpering combinations for the long run.
|
|
*/
|
|
&mmc3 {
|
|
interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
|
|
pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
|
|
pinctrl-names = "default";
|
|
vmmc-supply = <&wl12xx_vmmc>;
|
|
non-removable;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
wlcore: wlcore@2 {
|
|
compatible = "ti,wl1283";
|
|
reg = <2>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */
|
|
ref-clock-frequency = <26000000>;
|
|
tcxo-clock-frequency = <26000000>;
|
|
};
|
|
};
|
|
|
|
&uart2 {
|
|
/delete-property/dma-names;
|
|
bluetooth {
|
|
compatible = "ti,wl1283-st";
|
|
enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */
|
|
max-speed = <3000000>;
|
|
};
|
|
};
|
|
|
|
/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */
|
|
&mt9p031_out {
|
|
pixel-clock-frequency = <90000000>;
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
mmc3_pins: pinmux_mm3_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
|
|
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
|
|
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core2 {
|
|
mmc3_core2_pins: pinmux_mmc3_core2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
|
|
OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
|
|
>;
|
|
};
|
|
};
|