![Mauro Carvalho Chehab](/assets/img/avatar_default.png)
As warned by sparse: drivers/media/platform/marvell-ccic/cafe-driver.c:475:23: warning: symbol 'ov7670_info' was not declared. Should it be static? Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
692 lines
18 KiB
C
692 lines
18 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* A driver for the CMOS camera controller in the Marvell 88ALP01 "cafe"
|
|
* multifunction chip. Currently works with the Omnivision OV7670
|
|
* sensor.
|
|
*
|
|
* The data sheet for this device can be found at:
|
|
* http://wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf
|
|
*
|
|
* Copyright 2006-11 One Laptop Per Child Association, Inc.
|
|
* Copyright 2006-11 Jonathan Corbet <corbet@lwn.net>
|
|
* Copyright 2018 Lubomir Rintel <lkundrak@v3.sk>
|
|
*
|
|
* Written by Jonathan Corbet, corbet@lwn.net.
|
|
*
|
|
* v4l2_device/v4l2_subdev conversion by:
|
|
* Copyright (C) 2009 Hans Verkuil <hverkuil@xs4all.nl>
|
|
*/
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/init.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/videodev2.h>
|
|
#include <media/v4l2-device.h>
|
|
#include <media/i2c/ov7670.h>
|
|
#include <linux/device.h>
|
|
#include <linux/wait.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/clkdev.h>
|
|
|
|
#include "mcam-core.h"
|
|
|
|
#define CAFE_VERSION 0x000002
|
|
|
|
|
|
/*
|
|
* Parameters.
|
|
*/
|
|
MODULE_AUTHOR("Jonathan Corbet <corbet@lwn.net>");
|
|
MODULE_DESCRIPTION("Marvell 88ALP01 CMOS Camera Controller driver");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_SUPPORTED_DEVICE("Video");
|
|
|
|
|
|
|
|
|
|
struct cafe_camera {
|
|
int registered; /* Fully initialized? */
|
|
struct mcam_camera mcam;
|
|
struct pci_dev *pdev;
|
|
struct i2c_adapter *i2c_adapter;
|
|
wait_queue_head_t smbus_wait; /* Waiting on i2c events */
|
|
};
|
|
|
|
/*
|
|
* Most of the camera controller registers are defined in mcam-core.h,
|
|
* but the Cafe platform has some additional registers of its own;
|
|
* they are described here.
|
|
*/
|
|
|
|
/*
|
|
* "General purpose register" has a couple of GPIOs used for sensor
|
|
* power and reset on OLPC XO 1.0 systems.
|
|
*/
|
|
#define REG_GPR 0xb4
|
|
#define GPR_C1EN 0x00000020 /* Pad 1 (power down) enable */
|
|
#define GPR_C0EN 0x00000010 /* Pad 0 (reset) enable */
|
|
#define GPR_C1 0x00000002 /* Control 1 value */
|
|
/*
|
|
* Control 0 is wired to reset on OLPC machines. For ov7x sensors,
|
|
* it is active low.
|
|
*/
|
|
#define GPR_C0 0x00000001 /* Control 0 value */
|
|
|
|
/*
|
|
* These registers control the SMBUS module for communicating
|
|
* with the sensor.
|
|
*/
|
|
#define REG_TWSIC0 0xb8 /* TWSI (smbus) control 0 */
|
|
#define TWSIC0_EN 0x00000001 /* TWSI enable */
|
|
#define TWSIC0_MODE 0x00000002 /* 1 = 16-bit, 0 = 8-bit */
|
|
#define TWSIC0_SID 0x000003fc /* Slave ID */
|
|
/*
|
|
* Subtle trickery: the slave ID field starts with bit 2. But the
|
|
* Linux i2c stack wants to treat the bottommost bit as a separate
|
|
* read/write bit, which is why slave ID's are usually presented
|
|
* >>1. For consistency with that behavior, we shift over three
|
|
* bits instead of two.
|
|
*/
|
|
#define TWSIC0_SID_SHIFT 3
|
|
#define TWSIC0_CLKDIV 0x0007fc00 /* Clock divider */
|
|
#define TWSIC0_MASKACK 0x00400000 /* Mask ack from sensor */
|
|
#define TWSIC0_OVMAGIC 0x00800000 /* Make it work on OV sensors */
|
|
|
|
#define REG_TWSIC1 0xbc /* TWSI control 1 */
|
|
#define TWSIC1_DATA 0x0000ffff /* Data to/from camchip */
|
|
#define TWSIC1_ADDR 0x00ff0000 /* Address (register) */
|
|
#define TWSIC1_ADDR_SHIFT 16
|
|
#define TWSIC1_READ 0x01000000 /* Set for read op */
|
|
#define TWSIC1_WSTAT 0x02000000 /* Write status */
|
|
#define TWSIC1_RVALID 0x04000000 /* Read data valid */
|
|
#define TWSIC1_ERROR 0x08000000 /* Something screwed up */
|
|
|
|
/*
|
|
* Here's the weird global control registers
|
|
*/
|
|
#define REG_GL_CSR 0x3004 /* Control/status register */
|
|
#define GCSR_SRS 0x00000001 /* SW Reset set */
|
|
#define GCSR_SRC 0x00000002 /* SW Reset clear */
|
|
#define GCSR_MRS 0x00000004 /* Master reset set */
|
|
#define GCSR_MRC 0x00000008 /* HW Reset clear */
|
|
#define GCSR_CCIC_EN 0x00004000 /* CCIC Clock enable */
|
|
#define REG_GL_IMASK 0x300c /* Interrupt mask register */
|
|
#define GIMSK_CCIC_EN 0x00000004 /* CCIC Interrupt enable */
|
|
|
|
#define REG_GL_FCR 0x3038 /* GPIO functional control register */
|
|
#define GFCR_GPIO_ON 0x08 /* Camera GPIO enabled */
|
|
#define REG_GL_GPIOR 0x315c /* GPIO register */
|
|
#define GGPIO_OUT 0x80000 /* GPIO output */
|
|
#define GGPIO_VAL 0x00008 /* Output pin value */
|
|
|
|
#define REG_LEN (REG_GL_IMASK + 4)
|
|
|
|
|
|
/*
|
|
* Debugging and related.
|
|
*/
|
|
#define cam_err(cam, fmt, arg...) \
|
|
dev_err(&(cam)->pdev->dev, fmt, ##arg);
|
|
#define cam_warn(cam, fmt, arg...) \
|
|
dev_warn(&(cam)->pdev->dev, fmt, ##arg);
|
|
|
|
/* -------------------------------------------------------------------- */
|
|
/*
|
|
* The I2C/SMBUS interface to the camera itself starts here. The
|
|
* controller handles SMBUS itself, presenting a relatively simple register
|
|
* interface; all we have to do is to tell it where to route the data.
|
|
*/
|
|
#define CAFE_SMBUS_TIMEOUT (HZ) /* generous */
|
|
|
|
static inline struct cafe_camera *to_cam(struct v4l2_device *dev)
|
|
{
|
|
struct mcam_camera *m = container_of(dev, struct mcam_camera, v4l2_dev);
|
|
return container_of(m, struct cafe_camera, mcam);
|
|
}
|
|
|
|
|
|
static int cafe_smbus_write_done(struct mcam_camera *mcam)
|
|
{
|
|
unsigned long flags;
|
|
int c1;
|
|
|
|
/*
|
|
* We must delay after the interrupt, or the controller gets confused
|
|
* and never does give us good status. Fortunately, we don't do this
|
|
* often.
|
|
*/
|
|
udelay(20);
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
c1 = mcam_reg_read(mcam, REG_TWSIC1);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
return (c1 & (TWSIC1_WSTAT|TWSIC1_ERROR)) != TWSIC1_WSTAT;
|
|
}
|
|
|
|
static int cafe_smbus_write_data(struct cafe_camera *cam,
|
|
u16 addr, u8 command, u8 value)
|
|
{
|
|
unsigned int rval;
|
|
unsigned long flags;
|
|
struct mcam_camera *mcam = &cam->mcam;
|
|
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID);
|
|
rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */
|
|
/*
|
|
* Marvell sez set clkdiv to all 1's for now.
|
|
*/
|
|
rval |= TWSIC0_CLKDIV;
|
|
mcam_reg_write(mcam, REG_TWSIC0, rval);
|
|
(void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */
|
|
rval = value | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR);
|
|
mcam_reg_write(mcam, REG_TWSIC1, rval);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
|
|
/* Unfortunately, reading TWSIC1 too soon after sending a command
|
|
* causes the device to die.
|
|
* Use a busy-wait because we often send a large quantity of small
|
|
* commands at-once; using msleep() would cause a lot of context
|
|
* switches which take longer than 2ms, resulting in a noticeable
|
|
* boot-time and capture-start delays.
|
|
*/
|
|
mdelay(2);
|
|
|
|
/*
|
|
* Another sad fact is that sometimes, commands silently complete but
|
|
* cafe_smbus_write_done() never becomes aware of this.
|
|
* This happens at random and appears to possible occur with any
|
|
* command.
|
|
* We don't understand why this is. We work around this issue
|
|
* with the timeout in the wait below, assuming that all commands
|
|
* complete within the timeout.
|
|
*/
|
|
wait_event_timeout(cam->smbus_wait, cafe_smbus_write_done(mcam),
|
|
CAFE_SMBUS_TIMEOUT);
|
|
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
rval = mcam_reg_read(mcam, REG_TWSIC1);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
|
|
if (rval & TWSIC1_WSTAT) {
|
|
cam_err(cam, "SMBUS write (%02x/%02x/%02x) timed out\n", addr,
|
|
command, value);
|
|
return -EIO;
|
|
}
|
|
if (rval & TWSIC1_ERROR) {
|
|
cam_err(cam, "SMBUS write (%02x/%02x/%02x) error\n", addr,
|
|
command, value);
|
|
return -EIO;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
|
|
|
|
static int cafe_smbus_read_done(struct mcam_camera *mcam)
|
|
{
|
|
unsigned long flags;
|
|
int c1;
|
|
|
|
/*
|
|
* We must delay after the interrupt, or the controller gets confused
|
|
* and never does give us good status. Fortunately, we don't do this
|
|
* often.
|
|
*/
|
|
udelay(20);
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
c1 = mcam_reg_read(mcam, REG_TWSIC1);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
return c1 & (TWSIC1_RVALID|TWSIC1_ERROR);
|
|
}
|
|
|
|
|
|
|
|
static int cafe_smbus_read_data(struct cafe_camera *cam,
|
|
u16 addr, u8 command, u8 *value)
|
|
{
|
|
unsigned int rval;
|
|
unsigned long flags;
|
|
struct mcam_camera *mcam = &cam->mcam;
|
|
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
rval = TWSIC0_EN | ((addr << TWSIC0_SID_SHIFT) & TWSIC0_SID);
|
|
rval |= TWSIC0_OVMAGIC; /* Make OV sensors work */
|
|
/*
|
|
* Marvel sez set clkdiv to all 1's for now.
|
|
*/
|
|
rval |= TWSIC0_CLKDIV;
|
|
mcam_reg_write(mcam, REG_TWSIC0, rval);
|
|
(void) mcam_reg_read(mcam, REG_TWSIC1); /* force write */
|
|
rval = TWSIC1_READ | ((command << TWSIC1_ADDR_SHIFT) & TWSIC1_ADDR);
|
|
mcam_reg_write(mcam, REG_TWSIC1, rval);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
|
|
wait_event_timeout(cam->smbus_wait,
|
|
cafe_smbus_read_done(mcam), CAFE_SMBUS_TIMEOUT);
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
rval = mcam_reg_read(mcam, REG_TWSIC1);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
|
|
if (rval & TWSIC1_ERROR) {
|
|
cam_err(cam, "SMBUS read (%02x/%02x) error\n", addr, command);
|
|
return -EIO;
|
|
}
|
|
if (!(rval & TWSIC1_RVALID)) {
|
|
cam_err(cam, "SMBUS read (%02x/%02x) timed out\n", addr,
|
|
command);
|
|
return -EIO;
|
|
}
|
|
*value = rval & 0xff;
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Perform a transfer over SMBUS. This thing is called under
|
|
* the i2c bus lock, so we shouldn't race with ourselves...
|
|
*/
|
|
static int cafe_smbus_xfer(struct i2c_adapter *adapter, u16 addr,
|
|
unsigned short flags, char rw, u8 command,
|
|
int size, union i2c_smbus_data *data)
|
|
{
|
|
struct cafe_camera *cam = i2c_get_adapdata(adapter);
|
|
int ret = -EINVAL;
|
|
|
|
/*
|
|
* This interface would appear to only do byte data ops. OK
|
|
* it can do word too, but the cam chip has no use for that.
|
|
*/
|
|
if (size != I2C_SMBUS_BYTE_DATA) {
|
|
cam_err(cam, "funky xfer size %d\n", size);
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (rw == I2C_SMBUS_WRITE)
|
|
ret = cafe_smbus_write_data(cam, addr, command, data->byte);
|
|
else if (rw == I2C_SMBUS_READ)
|
|
ret = cafe_smbus_read_data(cam, addr, command, &data->byte);
|
|
return ret;
|
|
}
|
|
|
|
|
|
static void cafe_smbus_enable_irq(struct cafe_camera *cam)
|
|
{
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&cam->mcam.dev_lock, flags);
|
|
mcam_reg_set_bit(&cam->mcam, REG_IRQMASK, TWSIIRQS);
|
|
spin_unlock_irqrestore(&cam->mcam.dev_lock, flags);
|
|
}
|
|
|
|
static u32 cafe_smbus_func(struct i2c_adapter *adapter)
|
|
{
|
|
return I2C_FUNC_SMBUS_READ_BYTE_DATA |
|
|
I2C_FUNC_SMBUS_WRITE_BYTE_DATA;
|
|
}
|
|
|
|
static const struct i2c_algorithm cafe_smbus_algo = {
|
|
.smbus_xfer = cafe_smbus_xfer,
|
|
.functionality = cafe_smbus_func
|
|
};
|
|
|
|
static int cafe_smbus_setup(struct cafe_camera *cam)
|
|
{
|
|
struct i2c_adapter *adap;
|
|
int ret;
|
|
|
|
adap = kzalloc(sizeof(*adap), GFP_KERNEL);
|
|
if (adap == NULL)
|
|
return -ENOMEM;
|
|
adap->owner = THIS_MODULE;
|
|
adap->algo = &cafe_smbus_algo;
|
|
strscpy(adap->name, "cafe_ccic", sizeof(adap->name));
|
|
adap->dev.parent = &cam->pdev->dev;
|
|
i2c_set_adapdata(adap, cam);
|
|
ret = i2c_add_adapter(adap);
|
|
if (ret) {
|
|
printk(KERN_ERR "Unable to register cafe i2c adapter\n");
|
|
kfree(adap);
|
|
return ret;
|
|
}
|
|
|
|
cam->i2c_adapter = adap;
|
|
cafe_smbus_enable_irq(cam);
|
|
return 0;
|
|
}
|
|
|
|
static void cafe_smbus_shutdown(struct cafe_camera *cam)
|
|
{
|
|
i2c_del_adapter(cam->i2c_adapter);
|
|
kfree(cam->i2c_adapter);
|
|
}
|
|
|
|
|
|
/*
|
|
* Controller-level stuff
|
|
*/
|
|
|
|
static void cafe_ctlr_init(struct mcam_camera *mcam)
|
|
{
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
/*
|
|
* Added magic to bring up the hardware on the B-Test board
|
|
*/
|
|
mcam_reg_write(mcam, 0x3038, 0x8);
|
|
mcam_reg_write(mcam, 0x315c, 0x80008);
|
|
/*
|
|
* Go through the dance needed to wake the device up.
|
|
* Note that these registers are global and shared
|
|
* with the NAND and SD devices. Interaction between the
|
|
* three still needs to be examined.
|
|
*/
|
|
mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRS|GCSR_MRS); /* Needed? */
|
|
mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRC);
|
|
mcam_reg_write(mcam, REG_GL_CSR, GCSR_SRC|GCSR_MRS);
|
|
/*
|
|
* Here we must wait a bit for the controller to come around.
|
|
*/
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
msleep(5);
|
|
spin_lock_irqsave(&mcam->dev_lock, flags);
|
|
|
|
mcam_reg_write(mcam, REG_GL_CSR, GCSR_CCIC_EN|GCSR_SRC|GCSR_MRC);
|
|
mcam_reg_set_bit(mcam, REG_GL_IMASK, GIMSK_CCIC_EN);
|
|
/*
|
|
* Mask all interrupts.
|
|
*/
|
|
mcam_reg_write(mcam, REG_IRQMASK, 0);
|
|
spin_unlock_irqrestore(&mcam->dev_lock, flags);
|
|
}
|
|
|
|
|
|
static int cafe_ctlr_power_up(struct mcam_camera *mcam)
|
|
{
|
|
/*
|
|
* Part one of the sensor dance: turn the global
|
|
* GPIO signal on.
|
|
*/
|
|
mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON);
|
|
mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT|GGPIO_VAL);
|
|
/*
|
|
* Put the sensor into operational mode (assumes OLPC-style
|
|
* wiring). Control 0 is reset - set to 1 to operate.
|
|
* Control 1 is power down, set to 0 to operate.
|
|
*/
|
|
mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN); /* pwr up, reset */
|
|
mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void cafe_ctlr_power_down(struct mcam_camera *mcam)
|
|
{
|
|
mcam_reg_write(mcam, REG_GPR, GPR_C1EN|GPR_C0EN|GPR_C1);
|
|
mcam_reg_write(mcam, REG_GL_FCR, GFCR_GPIO_ON);
|
|
mcam_reg_write(mcam, REG_GL_GPIOR, GGPIO_OUT);
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
* The platform interrupt handler.
|
|
*/
|
|
static irqreturn_t cafe_irq(int irq, void *data)
|
|
{
|
|
struct cafe_camera *cam = data;
|
|
struct mcam_camera *mcam = &cam->mcam;
|
|
unsigned int irqs, handled;
|
|
|
|
spin_lock(&mcam->dev_lock);
|
|
irqs = mcam_reg_read(mcam, REG_IRQSTAT);
|
|
handled = cam->registered && mccic_irq(mcam, irqs);
|
|
if (irqs & TWSIIRQS) {
|
|
mcam_reg_write(mcam, REG_IRQSTAT, TWSIIRQS);
|
|
wake_up(&cam->smbus_wait);
|
|
handled = 1;
|
|
}
|
|
spin_unlock(&mcam->dev_lock);
|
|
return IRQ_RETVAL(handled);
|
|
}
|
|
|
|
/* -------------------------------------------------------------------------- */
|
|
|
|
static struct ov7670_config sensor_cfg = {
|
|
/*
|
|
* Exclude QCIF mode, because it only captures a tiny portion
|
|
* of the sensor FOV
|
|
*/
|
|
.min_width = 320,
|
|
.min_height = 240,
|
|
|
|
/*
|
|
* Set the clock speed for the XO 1; I don't believe this
|
|
* driver has ever run anywhere else.
|
|
*/
|
|
.clock_speed = 45,
|
|
.use_smbus = 1,
|
|
};
|
|
|
|
static struct i2c_board_info ov7670_info = {
|
|
.type = "ov7670",
|
|
.addr = 0x42 >> 1,
|
|
.platform_data = &sensor_cfg,
|
|
};
|
|
|
|
/* -------------------------------------------------------------------------- */
|
|
/*
|
|
* PCI interface stuff.
|
|
*/
|
|
|
|
static int cafe_pci_probe(struct pci_dev *pdev,
|
|
const struct pci_device_id *id)
|
|
{
|
|
int ret;
|
|
struct cafe_camera *cam;
|
|
struct mcam_camera *mcam;
|
|
|
|
/*
|
|
* Start putting together one of our big camera structures.
|
|
*/
|
|
ret = -ENOMEM;
|
|
cam = kzalloc(sizeof(struct cafe_camera), GFP_KERNEL);
|
|
if (cam == NULL)
|
|
goto out;
|
|
cam->pdev = pdev;
|
|
mcam = &cam->mcam;
|
|
mcam->chip_id = MCAM_CAFE;
|
|
spin_lock_init(&mcam->dev_lock);
|
|
init_waitqueue_head(&cam->smbus_wait);
|
|
mcam->plat_power_up = cafe_ctlr_power_up;
|
|
mcam->plat_power_down = cafe_ctlr_power_down;
|
|
mcam->dev = &pdev->dev;
|
|
snprintf(mcam->bus_info, sizeof(mcam->bus_info), "PCI:%s", pci_name(pdev));
|
|
/*
|
|
* Vmalloc mode for buffers is traditional with this driver.
|
|
* We *might* be able to run DMA_contig, especially on a system
|
|
* with CMA in it.
|
|
*/
|
|
mcam->buffer_mode = B_vmalloc;
|
|
/*
|
|
* Get set up on the PCI bus.
|
|
*/
|
|
ret = pci_enable_device(pdev);
|
|
if (ret)
|
|
goto out_free;
|
|
pci_set_master(pdev);
|
|
|
|
ret = -EIO;
|
|
mcam->regs = pci_iomap(pdev, 0, 0);
|
|
if (!mcam->regs) {
|
|
printk(KERN_ERR "Unable to ioremap cafe-ccic regs\n");
|
|
goto out_disable;
|
|
}
|
|
mcam->regs_size = pci_resource_len(pdev, 0);
|
|
ret = request_irq(pdev->irq, cafe_irq, IRQF_SHARED, "cafe-ccic", cam);
|
|
if (ret)
|
|
goto out_iounmap;
|
|
|
|
/*
|
|
* Initialize the controller.
|
|
*/
|
|
cafe_ctlr_init(mcam);
|
|
|
|
/*
|
|
* Set up I2C/SMBUS communications. We have to drop the mutex here
|
|
* because the sensor could attach in this call chain, leading to
|
|
* unsightly deadlocks.
|
|
*/
|
|
ret = cafe_smbus_setup(cam);
|
|
if (ret)
|
|
goto out_pdown;
|
|
|
|
mcam->asd.match_type = V4L2_ASYNC_MATCH_I2C;
|
|
mcam->asd.match.i2c.adapter_id = i2c_adapter_id(cam->i2c_adapter);
|
|
mcam->asd.match.i2c.address = ov7670_info.addr;
|
|
|
|
ret = mccic_register(mcam);
|
|
if (ret)
|
|
goto out_smbus_shutdown;
|
|
|
|
clkdev_create(mcam->mclk, "xclk", "%d-%04x",
|
|
i2c_adapter_id(cam->i2c_adapter), ov7670_info.addr);
|
|
|
|
if (i2c_new_device(cam->i2c_adapter, &ov7670_info)) {
|
|
cam->registered = 1;
|
|
return 0;
|
|
}
|
|
|
|
mccic_shutdown(mcam);
|
|
out_smbus_shutdown:
|
|
cafe_smbus_shutdown(cam);
|
|
out_pdown:
|
|
cafe_ctlr_power_down(mcam);
|
|
free_irq(pdev->irq, cam);
|
|
out_iounmap:
|
|
pci_iounmap(pdev, mcam->regs);
|
|
out_disable:
|
|
pci_disable_device(pdev);
|
|
out_free:
|
|
kfree(cam);
|
|
out:
|
|
return ret;
|
|
}
|
|
|
|
|
|
/*
|
|
* Shut down an initialized device
|
|
*/
|
|
static void cafe_shutdown(struct cafe_camera *cam)
|
|
{
|
|
mccic_shutdown(&cam->mcam);
|
|
cafe_smbus_shutdown(cam);
|
|
free_irq(cam->pdev->irq, cam);
|
|
pci_iounmap(cam->pdev, cam->mcam.regs);
|
|
}
|
|
|
|
|
|
static void cafe_pci_remove(struct pci_dev *pdev)
|
|
{
|
|
struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev);
|
|
struct cafe_camera *cam = to_cam(v4l2_dev);
|
|
|
|
if (cam == NULL) {
|
|
printk(KERN_WARNING "pci_remove on unknown pdev %p\n", pdev);
|
|
return;
|
|
}
|
|
cafe_shutdown(cam);
|
|
kfree(cam);
|
|
}
|
|
|
|
|
|
#ifdef CONFIG_PM
|
|
/*
|
|
* Basic power management.
|
|
*/
|
|
static int cafe_pci_suspend(struct pci_dev *pdev, pm_message_t state)
|
|
{
|
|
struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev);
|
|
struct cafe_camera *cam = to_cam(v4l2_dev);
|
|
int ret;
|
|
|
|
ret = pci_save_state(pdev);
|
|
if (ret)
|
|
return ret;
|
|
mccic_suspend(&cam->mcam);
|
|
pci_disable_device(pdev);
|
|
return 0;
|
|
}
|
|
|
|
|
|
static int cafe_pci_resume(struct pci_dev *pdev)
|
|
{
|
|
struct v4l2_device *v4l2_dev = dev_get_drvdata(&pdev->dev);
|
|
struct cafe_camera *cam = to_cam(v4l2_dev);
|
|
int ret = 0;
|
|
|
|
pci_restore_state(pdev);
|
|
ret = pci_enable_device(pdev);
|
|
|
|
if (ret) {
|
|
cam_warn(cam, "Unable to re-enable device on resume!\n");
|
|
return ret;
|
|
}
|
|
cafe_ctlr_init(&cam->mcam);
|
|
return mccic_resume(&cam->mcam);
|
|
}
|
|
|
|
#endif /* CONFIG_PM */
|
|
|
|
static const struct pci_device_id cafe_ids[] = {
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL,
|
|
PCI_DEVICE_ID_MARVELL_88ALP01_CCIC) },
|
|
{ 0, }
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(pci, cafe_ids);
|
|
|
|
static struct pci_driver cafe_pci_driver = {
|
|
.name = "cafe1000-ccic",
|
|
.id_table = cafe_ids,
|
|
.probe = cafe_pci_probe,
|
|
.remove = cafe_pci_remove,
|
|
#ifdef CONFIG_PM
|
|
.suspend = cafe_pci_suspend,
|
|
.resume = cafe_pci_resume,
|
|
#endif
|
|
};
|
|
|
|
|
|
|
|
|
|
static int __init cafe_init(void)
|
|
{
|
|
int ret;
|
|
|
|
printk(KERN_NOTICE "Marvell M88ALP01 'CAFE' Camera Controller version %d\n",
|
|
CAFE_VERSION);
|
|
ret = pci_register_driver(&cafe_pci_driver);
|
|
if (ret) {
|
|
printk(KERN_ERR "Unable to register cafe_ccic driver\n");
|
|
goto out;
|
|
}
|
|
ret = 0;
|
|
|
|
out:
|
|
return ret;
|
|
}
|
|
|
|
|
|
static void __exit cafe_exit(void)
|
|
{
|
|
pci_unregister_driver(&cafe_pci_driver);
|
|
}
|
|
|
|
module_init(cafe_init);
|
|
module_exit(cafe_exit);
|