redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/arch/arm/mach-sa1100/h3600.c
Dmitry Artamonow 51834901fa ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs 
After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.

Drop this initialisation and configure all GPIOs as input.

Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-06 16:52:55 +00:00

489 lines
11 KiB
C
Raw Blame History

/*
* Hardware definitions for Compaq iPAQ H3xxx Handheld Computers
*
* Copyright 2000,1 Compaq Computer Corporation.
*
* Use consistent with the GNU GPL is permitted,
* provided that this copyright notice is
* preserved in its entirety in all copies and derived works.
*
* COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
* AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
* FITNESS FOR ANY PARTICULAR PURPOSE.
*
* Author: Jamey Hicks.
*
* History:
*
* 2001-10-?? Andrew Christian Added support for iPAQ H3800
* and abstracted EGPIO interface.
*
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/tty.h>
#include <linux/pm.h>
#include <linux/device.h>
#include <linux/mfd/htc-egpio.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/serial_core.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <asm/irq.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/mach/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irda.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
#include <mach/h3600.h>
#include <mach/h3600_gpio.h>
#include "generic.h"
struct gpio_default_state {
int gpio;
int mode;
const char *name;
};
#define GPIO_MODE_IN -1
#define GPIO_MODE_OUT0 0
#define GPIO_MODE_OUT1 1
static void h3xxx_init_gpio(struct gpio_default_state *s, size_t n)
{
while (n--) {
const char *name = s->name;
int err;
if (!name)
name = "[init]";
err = gpio_request(s->gpio, name);
if (err) {
printk(KERN_ERR "gpio%u: unable to request: %d\n",
s->gpio, err);
continue;
}
if (s->mode >= 0) {
err = gpio_direction_output(s->gpio, s->mode);
} else {
err = gpio_direction_input(s->gpio);
}
if (err) {
printk(KERN_ERR "gpio%u: unable to set direction: %d\n",
s->gpio, err);
continue;
}
if (!s->name)
gpio_free(s->gpio);
s++;
}
}
/*
* H3xxx flash support
*/
static struct mtd_partition h3xxx_partitions[] = {
{
.name = "H3XXX boot firmware",
.size = 0x00040000,
.offset = 0,
.mask_flags = MTD_WRITEABLE, /* force read-only */
}, {
.name = "H3XXX rootfs",
.size = MTDPART_SIZ_FULL,
.offset = 0x00040000,
}
};
static void h3xxx_set_vpp(int vpp)
{
gpio_set_value(H3XXX_EGPIO_VPP_ON, vpp);
}
static int h3xxx_flash_init(void)
{
int err = gpio_request(H3XXX_EGPIO_VPP_ON, "Flash Vpp");
if (err)
return err;
err = gpio_direction_output(H3XXX_EGPIO_VPP_ON, 0);
if (err)
gpio_free(H3XXX_EGPIO_VPP_ON);
return err;
}
static void h3xxx_flash_exit(void)
{
gpio_free(H3XXX_EGPIO_VPP_ON);
}
static struct flash_platform_data h3xxx_flash_data = {
.map_name = "cfi_probe",
.set_vpp = h3xxx_set_vpp,
.init = h3xxx_flash_init,
.exit = h3xxx_flash_exit,
.parts = h3xxx_partitions,
.nr_parts = ARRAY_SIZE(h3xxx_partitions),
};
static struct resource h3xxx_flash_resource = {
.start = SA1100_CS0_PHYS,
.end = SA1100_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
/*
* H3xxx uart support
*/
static void h3xxx_uart_set_mctrl(struct uart_port *port, u_int mctrl)
{
if (port->mapbase == _Ser3UTCR0) {
gpio_set_value(H3XXX_GPIO_COM_RTS, !(mctrl & TIOCM_RTS));
}
}
static u_int h3xxx_uart_get_mctrl(struct uart_port *port)
{
u_int ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR;
if (port->mapbase == _Ser3UTCR0) {
/*
* DCD and CTS bits are inverted in GPLR by RS232 transceiver
*/
if (gpio_get_value(H3XXX_GPIO_COM_DCD))
ret &= ~TIOCM_CD;
if (gpio_get_value(H3XXX_GPIO_COM_CTS))
ret &= ~TIOCM_CTS;
}
return ret;
}
static void h3xxx_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
{
if (port->mapbase == _Ser3UTCR0)
if (!gpio_request(H3XXX_EGPIO_RS232_ON, "RS232 transceiver")) {
gpio_direction_output(H3XXX_EGPIO_RS232_ON, !state);
gpio_free(H3XXX_EGPIO_RS232_ON);
}
}
/*
* Enable/Disable wake up events for this serial port.
* Obviously, we only support this on the normal COM port.
*/
static int h3xxx_uart_set_wake(struct uart_port *port, u_int enable)
{
int err = -EINVAL;
if (port->mapbase == _Ser3UTCR0) {
if (enable)
PWER |= PWER_GPIO23 | PWER_GPIO25; /* DCD and CTS */
else
PWER &= ~(PWER_GPIO23 | PWER_GPIO25); /* DCD and CTS */
err = 0;
}
return err;
}
static struct sa1100_port_fns h3xxx_port_fns __initdata = {
.set_mctrl = h3xxx_uart_set_mctrl,
.get_mctrl = h3xxx_uart_get_mctrl,
.pm = h3xxx_uart_pm,
.set_wake = h3xxx_uart_set_wake,
};
/*
* EGPIO
*/
static struct resource egpio_resources[] = {
[0] = {
.start = H3600_EGPIO_PHYS,
.end = H3600_EGPIO_PHYS + 0x4 - 1,
.flags = IORESOURCE_MEM,
},
};
static struct htc_egpio_chip egpio_chips[] = {
[0] = {
.reg_start = 0,
.gpio_base = H3XXX_EGPIO_BASE,
.num_gpios = 16,
.direction = HTC_EGPIO_OUTPUT,
.initial_values = 0x0080, /* H3XXX_EGPIO_RS232_ON */
},
};
static struct htc_egpio_platform_data egpio_info = {
.reg_width = 16,
.bus_width = 16,
.chip = egpio_chips,
.num_chips = ARRAY_SIZE(egpio_chips),
};
static struct platform_device h3xxx_egpio = {
.name = "htc-egpio",
.id = -1,
.resource = egpio_resources,
.num_resources = ARRAY_SIZE(egpio_resources),
.dev = {
.platform_data = &egpio_info,
},
};
static struct platform_device *h3xxx_devices[] = {
&h3xxx_egpio,
};
static void __init h3xxx_mach_init(void)
{
sa1100_register_uart_fns(&h3xxx_port_fns);
sa11x0_register_mtd(&h3xxx_flash_data, &h3xxx_flash_resource, 1);
platform_add_devices(h3xxx_devices, ARRAY_SIZE(h3xxx_devices));
}
static struct map_desc h3600_io_desc[] __initdata = {
{ /* static memory bank 2 CS#2 */
.virtual = H3600_BANK_2_VIRT,
.pfn = __phys_to_pfn(SA1100_CS2_PHYS),
.length = 0x02800000,
.type = MT_DEVICE
}, { /* static memory bank 4 CS#4 */
.virtual = H3600_BANK_4_VIRT,
.pfn = __phys_to_pfn(SA1100_CS4_PHYS),
.length = 0x00800000,
.type = MT_DEVICE
}, { /* EGPIO 0 CS#5 */
.virtual = H3600_EGPIO_VIRT,
.pfn = __phys_to_pfn(H3600_EGPIO_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
}
};
/*
* Common map_io initialization
*/
static void __init h3xxx_map_io(void)
{
sa1100_map_io();
iotable_init(h3600_io_desc, ARRAY_SIZE(h3600_io_desc));
sa1100_register_uart(0, 3); /* Common serial port */
// sa1100_register_uart(1, 1); /* Microcontroller on 3100/3600 */
/* Ensure those pins are outputs and driving low */
PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
/* Configure suspend conditions */
PGSR = 0;
PWER = PWER_GPIO0;
PCFR = PCFR_OPDE;
PSDR = 0;
GPCR = 0x0fffffff; /* All outputs are set low by default */
GPDR = 0; /* Configure all GPIOs as input */
}
/************************* H3100 *************************/
#ifdef CONFIG_SA1100_H3100
/*
* helper for sa1100fb
*/
static void h3100_lcd_power(int enable)
{
if (!gpio_request(H3XXX_EGPIO_LCD_ON, "LCD ON")) {
gpio_set_value(H3100_GPIO_LCD_3V_ON, enable);
gpio_direction_output(H3XXX_EGPIO_LCD_ON, enable);
gpio_free(H3XXX_EGPIO_LCD_ON);
}
}
static void __init h3100_map_io(void)
{
h3xxx_map_io();
sa1100fb_lcd_power = h3100_lcd_power;
/* Older bootldrs put GPIO2-9 in alternate mode on the
assumption that they are used for video */
GAFR &= ~0x000001fb;
}
/*
* This turns the IRDA power on or off on the Compaq H3100
*/
static int h3100_irda_set_power(struct device *dev, unsigned int state)
{
gpio_set_value(H3100_GPIO_IR_ON, state);
return 0;
}
static void h3100_irda_set_speed(struct device *dev, unsigned int speed)
{
gpio_set_value(H3100_GPIO_IR_FSEL, !(speed < 4000000));
}
static struct irda_platform_data h3100_irda_data = {
.set_power = h3100_irda_set_power,
.set_speed = h3100_irda_set_speed,
};
static struct gpio_default_state h3100_default_gpio[] = {
{ H3100_GPIO_IR_ON, GPIO_MODE_OUT0, "IrDA power" },
{ H3100_GPIO_IR_FSEL, GPIO_MODE_OUT0, "IrDA fsel" },
{ H3XXX_GPIO_COM_DCD, GPIO_MODE_IN, "COM DCD" },
{ H3XXX_GPIO_COM_CTS, GPIO_MODE_IN, "COM CTS" },
{ H3XXX_GPIO_COM_RTS, GPIO_MODE_OUT0, "COM RTS" },
{ H3100_GPIO_LCD_3V_ON, GPIO_MODE_OUT0, "LCD 3v" },
};
static void __init h3100_mach_init(void)
{
h3xxx_init_gpio(h3100_default_gpio, ARRAY_SIZE(h3100_default_gpio));
h3xxx_mach_init();
sa11x0_register_irda(&h3100_irda_data);
}
MACHINE_START(H3100, "Compaq iPAQ H3100")
.phys_io = 0x80000000,
.io_pg_offst = ((0xf8000000) >> 18) & 0xfffc,
.boot_params = 0xc0000100,
.map_io = h3100_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
.init_machine = h3100_mach_init,
MACHINE_END
#endif /* CONFIG_SA1100_H3100 */
/************************* H3600 *************************/
#ifdef CONFIG_SA1100_H3600
/*
* helper for sa1100fb
*/
static void h3600_lcd_power(int enable)
{
if (gpio_request(H3XXX_EGPIO_LCD_ON, "LCD power"))
goto err1;
if (gpio_request(H3600_EGPIO_LCD_PCI, "LCD control"))
goto err2;
if (gpio_request(H3600_EGPIO_LCD_5V_ON, "LCD 5v"))
goto err3;
if (gpio_request(H3600_EGPIO_LVDD_ON, "LCD 9v/-6.5v"))
goto err4;
gpio_direction_output(H3XXX_EGPIO_LCD_ON, enable);
gpio_direction_output(H3600_EGPIO_LCD_PCI, enable);
gpio_direction_output(H3600_EGPIO_LCD_5V_ON, enable);
gpio_direction_output(H3600_EGPIO_LVDD_ON, enable);
gpio_free(H3600_EGPIO_LVDD_ON);
err4: gpio_free(H3600_EGPIO_LCD_5V_ON);
err3: gpio_free(H3600_EGPIO_LCD_PCI);
err2: gpio_free(H3XXX_EGPIO_LCD_ON);
err1: return;
}
static void __init h3600_map_io(void)
{
h3xxx_map_io();
sa1100fb_lcd_power = h3600_lcd_power;
}
/*
* This turns the IRDA power on or off on the Compaq H3600
*/
static int h3600_irda_set_power(struct device *dev, unsigned int state)
{
gpio_set_value(H3600_EGPIO_IR_ON, state);
return 0;
}
static void h3600_irda_set_speed(struct device *dev, unsigned int speed)
{
gpio_set_value(H3600_EGPIO_IR_FSEL, !(speed < 4000000));
}
static int h3600_irda_startup(struct device *dev)
{
int err = gpio_request(H3600_EGPIO_IR_ON, "IrDA power");
if (err)
goto err1;
err = gpio_direction_output(H3600_EGPIO_IR_ON, 0);
if (err)
goto err2;
err = gpio_request(H3600_EGPIO_IR_FSEL, "IrDA fsel");
if (err)
goto err2;
err = gpio_direction_output(H3600_EGPIO_IR_FSEL, 0);
if (err)
goto err3;
return 0;
err3: gpio_free(H3600_EGPIO_IR_FSEL);
err2: gpio_free(H3600_EGPIO_IR_ON);
err1: return err;
}
static void h3600_irda_shutdown(struct device *dev)
{
gpio_free(H3600_EGPIO_IR_ON);
gpio_free(H3600_EGPIO_IR_FSEL);
}
static struct irda_platform_data h3600_irda_data = {
.set_power = h3600_irda_set_power,
.set_speed = h3600_irda_set_speed,
.startup = h3600_irda_startup,
.shutdown = h3600_irda_shutdown,
};
static struct gpio_default_state h3600_default_gpio[] = {
{ H3XXX_GPIO_COM_DCD, GPIO_MODE_IN, "COM DCD" },
{ H3XXX_GPIO_COM_CTS, GPIO_MODE_IN, "COM CTS" },
{ H3XXX_GPIO_COM_RTS, GPIO_MODE_OUT0, "COM RTS" },
};
static void __init h3600_mach_init(void)
{
h3xxx_init_gpio(h3600_default_gpio, ARRAY_SIZE(h3600_default_gpio));
h3xxx_mach_init();
sa11x0_register_irda(&h3600_irda_data);
}
MACHINE_START(H3600, "Compaq iPAQ H3600")
.phys_io = 0x80000000,
.io_pg_offst = ((0xf8000000) >> 18) & 0xfffc,
.boot_params = 0xc0000100,
.map_io = h3600_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
.init_machine = h3600_mach_init,
MACHINE_END
#endif /* CONFIG_SA1100_H3600 */
View git blame Copy permalink