![Pavel Roskin](/assets/img/avatar_default.png)
Signed-off-by: Pavel Roskin <proski@gnu.org> Remove inneeded system includes. Most system includes are not needed. In particular, the hardware backends don't need anything network related. Some includes have been moved from local headers to the C files where they are actually used. Includes that have to be in the local headers are no longer from the C sources. Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
404 lines
13 KiB
C
404 lines
13 KiB
C
/* orinoco_plx.c
|
|
*
|
|
* Driver for Prism II devices which would usually be driven by orinoco_cs,
|
|
* but are connected to the PCI bus by a PLX9052.
|
|
*
|
|
* Current maintainers (as of 29 September 2003) are:
|
|
* Pavel Roskin <proski AT gnu.org>
|
|
* and David Gibson <hermes AT gibson.dropbear.id.au>
|
|
*
|
|
* (C) Copyright David Gibson, IBM Corp. 2001-2003.
|
|
* Copyright (C) 2001 Daniel Barlow
|
|
*
|
|
* The contents of this file are subject to the Mozilla Public License
|
|
* Version 1.1 (the "License"); you may not use this file except in
|
|
* compliance with the License. You may obtain a copy of the License
|
|
* at http://www.mozilla.org/MPL/
|
|
*
|
|
* Software distributed under the License is distributed on an "AS IS"
|
|
* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
|
|
* the License for the specific language governing rights and
|
|
* limitations under the License.
|
|
*
|
|
* Alternatively, the contents of this file may be used under the
|
|
* terms of the GNU General Public License version 2 (the "GPL"), in
|
|
* which case the provisions of the GPL are applicable instead of the
|
|
* above. If you wish to allow the use of your version of this file
|
|
* only under the terms of the GPL and not to allow others to use your
|
|
* version of this file under the MPL, indicate your decision by
|
|
* deleting the provisions above and replace them with the notice and
|
|
* other provisions required by the GPL. If you do not delete the
|
|
* provisions above, a recipient may use your version of this file
|
|
* under either the MPL or the GPL.
|
|
|
|
* Caution: this is experimental and probably buggy. For success and
|
|
* failure reports for different cards and adaptors, see
|
|
* orinoco_plx_pci_id_table near the end of the file. If you have a
|
|
* card we don't have the PCI id for, and looks like it should work,
|
|
* drop me mail with the id and "it works"/"it doesn't work".
|
|
*
|
|
* Note: if everything gets detected fine but it doesn't actually send
|
|
* or receive packets, your first port of call should probably be to
|
|
* try newer firmware in the card. Especially if you're doing Ad-Hoc
|
|
* modes.
|
|
*
|
|
* The actual driving is done by orinoco.c, this is just resource
|
|
* allocation stuff. The explanation below is courtesy of Ryan Niemi
|
|
* on the linux-wlan-ng list at
|
|
* http://archives.neohapsis.com/archives/dev/linux-wlan/2001-q1/0026.html
|
|
*
|
|
* The PLX9052-based cards (WL11000 and several others) are a
|
|
* different beast than the usual PCMCIA-based PRISM2 configuration
|
|
* expected by wlan-ng. Here's the general details on how the WL11000
|
|
* PCI adapter works:
|
|
*
|
|
* - Two PCI I/O address spaces, one 0x80 long which contains the
|
|
* PLX9052 registers, and one that's 0x40 long mapped to the PCMCIA
|
|
* slot I/O address space.
|
|
*
|
|
* - One PCI memory address space, mapped to the PCMCIA memory space
|
|
* (containing the CIS).
|
|
*
|
|
* After identifying the I/O and memory space, you can read through
|
|
* the memory space to confirm the CIS's device ID or manufacturer ID
|
|
* to make sure it's the expected card. qKeep in mind that the PCMCIA
|
|
* spec specifies the CIS as the lower 8 bits of each word read from
|
|
* the CIS, so to read the bytes of the CIS, read every other byte
|
|
* (0,2,4,...). Passing that test, you need to enable the I/O address
|
|
* space on the PCMCIA card via the PCMCIA COR register. This is the
|
|
* first byte following the CIS. In my case (which may not have any
|
|
* relation to what's on the PRISM2 cards), COR was at offset 0x800
|
|
* within the PCI memory space. Write 0x41 to the COR register to
|
|
* enable I/O mode and to select level triggered interrupts. To
|
|
* confirm you actually succeeded, read the COR register back and make
|
|
* sure it actually got set to 0x41, incase you have an unexpected
|
|
* card inserted.
|
|
*
|
|
* Following that, you can treat the second PCI I/O address space (the
|
|
* one that's not 0x80 in length) as the PCMCIA I/O space.
|
|
*
|
|
* Note that in the Eumitcom's source for their drivers, they register
|
|
* the interrupt as edge triggered when registering it with the
|
|
* Windows kernel. I don't recall how to register edge triggered on
|
|
* Linux (if it can be done at all). But in some experimentation, I
|
|
* don't see much operational difference between using either
|
|
* interrupt mode. Don't mess with the interrupt mode in the COR
|
|
* register though, as the PLX9052 wants level triggers with the way
|
|
* the serial EEPROM configures it on the WL11000.
|
|
*
|
|
* There's some other little quirks related to timing that I bumped
|
|
* into, but I don't recall right now. Also, there's two variants of
|
|
* the WL11000 I've seen, revision A1 and T2. These seem to differ
|
|
* slightly in the timings configured in the wait-state generator in
|
|
* the PLX9052. There have also been some comments from Eumitcom that
|
|
* cards shouldn't be hot swapped, apparently due to risk of cooking
|
|
* the PLX9052. I'm unsure why they believe this, as I can't see
|
|
* anything in the design that would really cause a problem, except
|
|
* for crashing drivers not written to expect it. And having developed
|
|
* drivers for the WL11000, I'd say it's quite tricky to write code
|
|
* that will successfully deal with a hot unplug. Very odd things
|
|
* happen on the I/O side of things. But anyway, be warned. Despite
|
|
* that, I've hot-swapped a number of times during debugging and
|
|
* driver development for various reasons (stuck WAIT# line after the
|
|
* radio card's firmware locks up).
|
|
*
|
|
* Hope this is enough info for someone to add PLX9052 support to the
|
|
* wlan-ng card. In the case of the WL11000, the PCI ID's are
|
|
* 0x1639/0x0200, with matching subsystem ID's. Other PLX9052-based
|
|
* manufacturers other than Eumitcom (or on cards other than the
|
|
* WL11000) may have different PCI ID's.
|
|
*
|
|
* If anyone needs any more specific info, let me know. I haven't had
|
|
* time to implement support myself yet, and with the way things are
|
|
* going, might not have time for a while..
|
|
*/
|
|
|
|
#define DRIVER_NAME "orinoco_plx"
|
|
#define PFX DRIVER_NAME ": "
|
|
|
|
#include <linux/config.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/pci.h>
|
|
#include <pcmcia/cisreg.h>
|
|
|
|
#include "orinoco.h"
|
|
|
|
#define COR_OFFSET (0x3e0) /* COR attribute offset of Prism2 PC card */
|
|
#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
|
|
#define COR_RESET (0x80) /* reset bit in the COR register */
|
|
#define PLX_RESET_TIME (500) /* milliseconds */
|
|
|
|
#define PLX_INTCSR 0x4c /* Interrupt Control & Status Register */
|
|
#define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */
|
|
|
|
static const u8 cis_magic[] = {
|
|
0x01, 0x03, 0x00, 0x00, 0xff, 0x17, 0x04, 0x67
|
|
};
|
|
|
|
/* Orinoco PLX specific data */
|
|
struct orinoco_plx_card {
|
|
void __iomem *attr_mem;
|
|
};
|
|
|
|
/*
|
|
* Do a soft reset of the card using the Configuration Option Register
|
|
*/
|
|
static int orinoco_plx_cor_reset(struct orinoco_private *priv)
|
|
{
|
|
hermes_t *hw = &priv->hw;
|
|
struct orinoco_plx_card *card = priv->card;
|
|
u8 __iomem *attr_mem = card->attr_mem;
|
|
unsigned long timeout;
|
|
u16 reg;
|
|
|
|
writeb(COR_VALUE | COR_RESET, attr_mem + COR_OFFSET);
|
|
mdelay(1);
|
|
|
|
writeb(COR_VALUE, attr_mem + COR_OFFSET);
|
|
mdelay(1);
|
|
|
|
/* Just in case, wait more until the card is no longer busy */
|
|
timeout = jiffies + (PLX_RESET_TIME * HZ / 1000);
|
|
reg = hermes_read_regn(hw, CMD);
|
|
while (time_before(jiffies, timeout) && (reg & HERMES_CMD_BUSY)) {
|
|
mdelay(1);
|
|
reg = hermes_read_regn(hw, CMD);
|
|
}
|
|
|
|
/* Did we timeout ? */
|
|
if (reg & HERMES_CMD_BUSY) {
|
|
printk(KERN_ERR PFX "Busy timeout\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
static int orinoco_plx_init_one(struct pci_dev *pdev,
|
|
const struct pci_device_id *ent)
|
|
{
|
|
int err = 0;
|
|
u8 __iomem *attr_mem = NULL;
|
|
u32 csr_reg, plx_addr;
|
|
struct orinoco_private *priv = NULL;
|
|
struct orinoco_plx_card *card;
|
|
unsigned long pccard_ioaddr = 0;
|
|
unsigned long pccard_iolen = 0;
|
|
struct net_device *dev = NULL;
|
|
void __iomem *mem;
|
|
int i;
|
|
|
|
err = pci_enable_device(pdev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "Cannot enable PCI device\n");
|
|
return err;
|
|
}
|
|
|
|
err = pci_request_regions(pdev, DRIVER_NAME);
|
|
if (err != 0) {
|
|
printk(KERN_ERR PFX "Cannot obtain PCI resources\n");
|
|
goto fail_resources;
|
|
}
|
|
|
|
/* Resource 1 is mapped to PLX-specific registers */
|
|
plx_addr = pci_resource_start(pdev, 1);
|
|
|
|
/* Resource 2 is mapped to the PCMCIA attribute memory */
|
|
attr_mem = ioremap(pci_resource_start(pdev, 2),
|
|
pci_resource_len(pdev, 2));
|
|
if (!attr_mem) {
|
|
printk(KERN_ERR PFX "Cannot remap PCMCIA space\n");
|
|
goto fail_map_attr;
|
|
}
|
|
|
|
/* Resource 3 is mapped to the PCMCIA I/O address space */
|
|
pccard_ioaddr = pci_resource_start(pdev, 3);
|
|
pccard_iolen = pci_resource_len(pdev, 3);
|
|
|
|
mem = pci_iomap(pdev, 3, 0);
|
|
if (!mem) {
|
|
err = -ENOMEM;
|
|
goto fail_map_io;
|
|
}
|
|
|
|
/* Allocate network device */
|
|
dev = alloc_orinocodev(sizeof(*card), orinoco_plx_cor_reset);
|
|
if (!dev) {
|
|
printk(KERN_ERR PFX "Cannot allocate network device\n");
|
|
err = -ENOMEM;
|
|
goto fail_alloc;
|
|
}
|
|
|
|
priv = netdev_priv(dev);
|
|
card = priv->card;
|
|
card->attr_mem = attr_mem;
|
|
dev->base_addr = pccard_ioaddr;
|
|
SET_MODULE_OWNER(dev);
|
|
SET_NETDEV_DEV(dev, &pdev->dev);
|
|
|
|
hermes_struct_init(&priv->hw, mem, HERMES_16BIT_REGSPACING);
|
|
|
|
printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 PLX device "
|
|
"at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
|
|
pccard_ioaddr);
|
|
|
|
err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
|
|
dev->name, dev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq);
|
|
err = -EBUSY;
|
|
goto fail_irq;
|
|
}
|
|
dev->irq = pdev->irq;
|
|
|
|
/* bjoern: We need to tell the card to enable interrupts, in
|
|
case the serial eprom didn't do this already. See the
|
|
PLX9052 data book, p8-1 and 8-24 for reference. */
|
|
csr_reg = inl(plx_addr + PLX_INTCSR);
|
|
if (!(csr_reg & PLX_INTCSR_INTEN)) {
|
|
csr_reg |= PLX_INTCSR_INTEN;
|
|
outl(csr_reg, plx_addr + PLX_INTCSR);
|
|
csr_reg = inl(plx_addr + PLX_INTCSR);
|
|
if (!(csr_reg & PLX_INTCSR_INTEN)) {
|
|
printk(KERN_ERR PFX "Cannot enable interrupts\n");
|
|
goto fail;
|
|
}
|
|
}
|
|
|
|
err = orinoco_plx_cor_reset(priv);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "Initial reset failed\n");
|
|
goto fail;
|
|
}
|
|
|
|
printk(KERN_DEBUG PFX "CIS: ");
|
|
for (i = 0; i < 16; i++) {
|
|
printk("%02X:", readb(attr_mem + 2*i));
|
|
}
|
|
printk("\n");
|
|
|
|
/* Verify whether a supported PC card is present */
|
|
/* FIXME: we probably need to be smarted about this */
|
|
for (i = 0; i < sizeof(cis_magic); i++) {
|
|
if (cis_magic[i] != readb(attr_mem +2*i)) {
|
|
printk(KERN_ERR PFX "The CIS value of Prism2 PC "
|
|
"card is unexpected\n");
|
|
err = -EIO;
|
|
goto fail;
|
|
}
|
|
}
|
|
|
|
err = register_netdev(dev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "Cannot register network device\n");
|
|
goto fail;
|
|
}
|
|
|
|
pci_set_drvdata(pdev, dev);
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
free_irq(pdev->irq, dev);
|
|
|
|
fail_irq:
|
|
pci_set_drvdata(pdev, NULL);
|
|
free_orinocodev(dev);
|
|
|
|
fail_alloc:
|
|
pci_iounmap(pdev, mem);
|
|
|
|
fail_map_io:
|
|
iounmap(attr_mem);
|
|
|
|
fail_map_attr:
|
|
pci_release_regions(pdev);
|
|
|
|
fail_resources:
|
|
pci_disable_device(pdev);
|
|
|
|
return err;
|
|
}
|
|
|
|
static void __devexit orinoco_plx_remove_one(struct pci_dev *pdev)
|
|
{
|
|
struct net_device *dev = pci_get_drvdata(pdev);
|
|
struct orinoco_private *priv = netdev_priv(dev);
|
|
struct orinoco_plx_card *card = priv->card;
|
|
u8 __iomem *attr_mem = card->attr_mem;
|
|
|
|
BUG_ON(! dev);
|
|
|
|
unregister_netdev(dev);
|
|
free_irq(dev->irq, dev);
|
|
pci_set_drvdata(pdev, NULL);
|
|
free_orinocodev(dev);
|
|
pci_iounmap(pdev, priv->hw.iobase);
|
|
iounmap(attr_mem);
|
|
pci_release_regions(pdev);
|
|
pci_disable_device(pdev);
|
|
}
|
|
|
|
|
|
static struct pci_device_id orinoco_plx_pci_id_table[] = {
|
|
{0x111a, 0x1023, PCI_ANY_ID, PCI_ANY_ID,}, /* Siemens SpeedStream SS1023 */
|
|
{0x1385, 0x4100, PCI_ANY_ID, PCI_ANY_ID,}, /* Netgear MA301 */
|
|
{0x15e8, 0x0130, PCI_ANY_ID, PCI_ANY_ID,}, /* Correga - does this work? */
|
|
{0x1638, 0x1100, PCI_ANY_ID, PCI_ANY_ID,}, /* SMC EZConnect SMC2602W,
|
|
Eumitcom PCI WL11000,
|
|
Addtron AWA-100 */
|
|
{0x16ab, 0x1100, PCI_ANY_ID, PCI_ANY_ID,}, /* Global Sun Tech GL24110P */
|
|
{0x16ab, 0x1101, PCI_ANY_ID, PCI_ANY_ID,}, /* Reported working, but unknown */
|
|
{0x16ab, 0x1102, PCI_ANY_ID, PCI_ANY_ID,}, /* Linksys WDT11 */
|
|
{0x16ec, 0x3685, PCI_ANY_ID, PCI_ANY_ID,}, /* USR 2415 */
|
|
{0xec80, 0xec00, PCI_ANY_ID, PCI_ANY_ID,}, /* Belkin F5D6000 tested by
|
|
Brendan W. McAdams <rit AT jacked-in.org> */
|
|
{0x10b7, 0x7770, PCI_ANY_ID, PCI_ANY_ID,}, /* 3Com AirConnect PCI tested by
|
|
Damien Persohn <damien AT persohn.net> */
|
|
{0,},
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(pci, orinoco_plx_pci_id_table);
|
|
|
|
static struct pci_driver orinoco_plx_driver = {
|
|
.name = DRIVER_NAME,
|
|
.id_table = orinoco_plx_pci_id_table,
|
|
.probe = orinoco_plx_init_one,
|
|
.remove = __devexit_p(orinoco_plx_remove_one),
|
|
};
|
|
|
|
static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
|
|
" (Pavel Roskin <proski@gnu.org>,"
|
|
" David Gibson <hermes@gibson.dropbear.id.au>,"
|
|
" Daniel Barlow <dan@telent.net>)";
|
|
MODULE_AUTHOR("Daniel Barlow <dan@telent.net>");
|
|
MODULE_DESCRIPTION("Driver for wireless LAN cards using the PLX9052 PCI bridge");
|
|
MODULE_LICENSE("Dual MPL/GPL");
|
|
|
|
static int __init orinoco_plx_init(void)
|
|
{
|
|
printk(KERN_DEBUG "%s\n", version);
|
|
return pci_module_init(&orinoco_plx_driver);
|
|
}
|
|
|
|
static void __exit orinoco_plx_exit(void)
|
|
{
|
|
pci_unregister_driver(&orinoco_plx_driver);
|
|
ssleep(1);
|
|
}
|
|
|
|
module_init(orinoco_plx_init);
|
|
module_exit(orinoco_plx_exit);
|
|
|
|
/*
|
|
* Local variables:
|
|
* c-indent-level: 8
|
|
* c-basic-offset: 8
|
|
* tab-width: 8
|
|
* End:
|
|
*/
|