1f63fab955
Many serially-attached GPIO and IIO devices are daisy-chainable.
Examples for GPIO devices are Maxim MAX3191x and TI SN65HVS88x:
https://datasheets.maximintegrated.com/en/ds/MAX31913.pdf
http://www.ti.com/lit/ds/symlink/sn65hvs880.pdf
Examples for IIO devices are TI DAC128S085 and TI DAC161S055:
http://www.ti.com/lit/ds/symlink/dac128s085.pdf
http://www.ti.com/lit/ds/symlink/dac161s055.pdf
We already have drivers for daisy-chainable devices in the tree but
their devicetree bindings are somewhat inconsistent and ill-named:
The gpio-74x164.c driver uses "registers-number" to convey the
number of devices in the daisy-chain. (Sans vendor prefix,
multiple vendors sell compatible versions of this chip.)
The gpio-pisosr.c driver takes a different approach and calculates
the number of devices in the daisy-chain by dividing the common
"ngpios" property (Documentation/devicetree/bindings/gpio/gpio.txt)
by 8 (which assumes that each chip has 8 inputs).
Let's standardize on a common "#daisy-chained-devices" property.
That name was chosen because it's the term most frequently used in
datasheets. (A less frequently used synonym is "cascaded devices".)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
87 lines
2.8 KiB
Plaintext
87 lines
2.8 KiB
Plaintext
Common properties
|
|
=================
|
|
|
|
Endianness
|
|
----------
|
|
|
|
The Devicetree Specification does not define any properties related to hardware
|
|
byteswapping, but endianness issues show up frequently in porting Linux to
|
|
different machine types. This document attempts to provide a consistent
|
|
way of handling byteswapping across drivers.
|
|
|
|
Optional properties:
|
|
- big-endian: Boolean; force big endian register accesses
|
|
unconditionally (e.g. ioread32be/iowrite32be). Use this if you
|
|
know the peripheral always needs to be accessed in BE mode.
|
|
- little-endian: Boolean; force little endian register accesses
|
|
unconditionally (e.g. readl/writel). Use this if you know the
|
|
peripheral always needs to be accessed in LE mode.
|
|
- native-endian: Boolean; always use register accesses matched to the
|
|
endianness of the kernel binary (e.g. LE vmlinux -> readl/writel,
|
|
BE vmlinux -> ioread32be/iowrite32be). In this case no byteswaps
|
|
will ever be performed. Use this if the hardware "self-adjusts"
|
|
register endianness based on the CPU's configured endianness.
|
|
|
|
If a binding supports these properties, then the binding should also
|
|
specify the default behavior if none of these properties are present.
|
|
In such cases, little-endian is the preferred default, but it is not
|
|
a requirement. The of_device_is_big_endian() and of_fdt_is_big_endian()
|
|
helper functions do assume that little-endian is the default, because
|
|
most existing (PCI-based) drivers implicitly default to LE by using
|
|
readl/writel for MMIO accesses.
|
|
|
|
Examples:
|
|
Scenario 1 : CPU in LE mode & device in LE mode.
|
|
dev: dev@40031000 {
|
|
compatible = "name";
|
|
reg = <0x40031000 0x1000>;
|
|
...
|
|
native-endian;
|
|
};
|
|
|
|
Scenario 2 : CPU in LE mode & device in BE mode.
|
|
dev: dev@40031000 {
|
|
compatible = "name";
|
|
reg = <0x40031000 0x1000>;
|
|
...
|
|
big-endian;
|
|
};
|
|
|
|
Scenario 3 : CPU in BE mode & device in BE mode.
|
|
dev: dev@40031000 {
|
|
compatible = "name";
|
|
reg = <0x40031000 0x1000>;
|
|
...
|
|
native-endian;
|
|
};
|
|
|
|
Scenario 4 : CPU in BE mode & device in LE mode.
|
|
dev: dev@40031000 {
|
|
compatible = "name";
|
|
reg = <0x40031000 0x1000>;
|
|
...
|
|
little-endian;
|
|
};
|
|
|
|
Daisy-chained devices
|
|
---------------------
|
|
|
|
Many serially-attached GPIO and IIO devices are daisy-chainable. To the
|
|
host controller, a daisy-chain appears as a single device, but the number
|
|
of inputs and outputs it provides is the sum of inputs and outputs provided
|
|
by all of its devices. The driver needs to know how many devices the
|
|
daisy-chain comprises to determine the amount of data exchanged, how many
|
|
inputs and outputs to register and so on.
|
|
|
|
Optional properties:
|
|
- #daisy-chained-devices: Number of devices in the daisy-chain (default is 1).
|
|
|
|
Example:
|
|
gpio@0 {
|
|
compatible = "name";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
#daisy-chained-devices = <3>;
|
|
};
|