![Peter Griffin](/assets/img/avatar_default.png)
reset-gpios is more clear than rst-gpio. This change has been done as one atomic commit but it does breaks compatability with older dtbs. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
140 lines
2.9 KiB
Plaintext
140 lines
2.9 KiB
Plaintext
/*
|
|
* Copyright (C) 2014 STMicroelectronics (R&D) Limited.
|
|
* Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
#include <dt-bindings/clock/stih407-clks.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/media/c8sectpfe.h>
|
|
/ {
|
|
soc {
|
|
sbc_serial0: serial@9530000 {
|
|
status = "okay";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
red {
|
|
#gpio-cells = <2>;
|
|
label = "Front Panel LED";
|
|
gpios = <&pio4 1 0>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
green {
|
|
#gpio-cells = <2>;
|
|
gpios = <&pio1 3 0>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
|
|
pwm0: pwm@9810000 {
|
|
status = "okay";
|
|
};
|
|
|
|
pwm1: pwm@9510000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ssc2: i2c@9842000 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
st,i2c-min-scl-pulse-width-us = <0>;
|
|
st,i2c-min-sda-pulse-width-us = <5>;
|
|
};
|
|
|
|
ssc3: i2c@9843000 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
st,i2c-min-scl-pulse-width-us = <0>;
|
|
st,i2c-min-sda-pulse-width-us = <5>;
|
|
};
|
|
|
|
i2c@9844000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@9845000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@9540000 {
|
|
status = "okay";
|
|
};
|
|
|
|
mmc0: sdhci@09060000 {
|
|
status = "okay";
|
|
};
|
|
|
|
mmc1: sdhci@09080000 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* SSC11 to HDMI */
|
|
hdmiddc: i2c@9541000 {
|
|
status = "okay";
|
|
/* HDMI V1.3a supports Standard mode only */
|
|
clock-frequency = <100000>;
|
|
st,i2c-min-scl-pulse-width-us = <0>;
|
|
st,i2c-min-sda-pulse-width-us = <5>;
|
|
};
|
|
|
|
miphy28lp_phy: miphy28lp@9b22000 {
|
|
|
|
phy_port0: port@9b22000 {
|
|
st,osc-rdy;
|
|
};
|
|
|
|
phy_port1: port@9b2a000 {
|
|
st,osc-force-ext;
|
|
};
|
|
};
|
|
|
|
st_dwc3: dwc3@8f94000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ethernet0: dwmac@9630000 {
|
|
st,tx-retime-src = "clkgen";
|
|
status = "okay";
|
|
phy-mode = "rgmii";
|
|
fixed-link = <0 1 1000 0 0>;
|
|
};
|
|
|
|
demux@08a20000 {
|
|
compatible = "st,stih407-c8sectpfe";
|
|
status = "okay";
|
|
reg = <0x08a20000 0x10000>,
|
|
<0x08a00000 0x4000>;
|
|
reg-names = "c8sectpfe", "c8sectpfe-ram";
|
|
interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>,
|
|
<GIC_SPI 35 IRQ_TYPE_NONE>;
|
|
interrupt-names = "c8sectpfe-error-irq",
|
|
"c8sectpfe-idle-irq";
|
|
pinctrl-0 = <&pinctrl_tsin0_serial>;
|
|
pinctrl-1 = <&pinctrl_tsin0_parallel>;
|
|
pinctrl-2 = <&pinctrl_tsin3_serial>;
|
|
pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
|
|
pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
|
|
pinctrl-names = "tsin0-serial",
|
|
"tsin0-parallel",
|
|
"tsin3-serial",
|
|
"tsin4-serial",
|
|
"tsin5-serial";
|
|
clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
|
|
clock-names = "c8sectpfe";
|
|
|
|
/* tsin0 is TSA on NIMA */
|
|
tsin0: port@0 {
|
|
tsin-num = <0>;
|
|
serial-not-parallel;
|
|
i2c-bus = <&ssc2>;
|
|
reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
|
|
dvb-card = <STV0367_TDA18212_NIMA_1>;
|
|
};
|
|
};
|
|
};
|
|
};
|