![Maya Nakamura](/assets/img/avatar_default.png)
Remove extra blank line. Issue found by checkpatch.pl. Signed-off-by: Maya Nakamura <m.maya.nakamura@gmail.com> Reviewed-by: Vaishali Thakkar <vthakkar@vaishalithakkar.in> Acked-by: Todd Poynor <toddpoynor@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
738 lines
20 KiB
C
738 lines
20 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Driver for the Apex chip.
|
|
*
|
|
* Copyright (C) 2018 Google, Inc.
|
|
*/
|
|
|
|
#include <linux/compiler.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <linux/fs.h>
|
|
#include <linux/init.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/module.h>
|
|
#include <linux/moduleparam.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/printk.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/uaccess.h>
|
|
|
|
#include "apex.h"
|
|
|
|
#include "gasket_core.h"
|
|
#include "gasket_interrupt.h"
|
|
#include "gasket_page_table.h"
|
|
#include "gasket_sysfs.h"
|
|
|
|
/* Constants */
|
|
#define APEX_DEVICE_NAME "Apex"
|
|
#define APEX_DRIVER_VERSION "1.0"
|
|
|
|
/* CSRs are in BAR 2. */
|
|
#define APEX_BAR_INDEX 2
|
|
|
|
#define APEX_PCI_VENDOR_ID 0x1ac1
|
|
#define APEX_PCI_DEVICE_ID 0x089a
|
|
|
|
/* Bar Offsets. */
|
|
#define APEX_BAR_OFFSET 0
|
|
#define APEX_CM_OFFSET 0x1000000
|
|
|
|
/* The sizes of each Apex BAR 2. */
|
|
#define APEX_BAR_BYTES 0x100000
|
|
#define APEX_CH_MEM_BYTES (PAGE_SIZE * MAX_NUM_COHERENT_PAGES)
|
|
|
|
/* The number of user-mappable memory ranges in BAR2 of a Apex chip. */
|
|
#define NUM_REGIONS 3
|
|
|
|
/* The number of nodes in a Apex chip. */
|
|
#define NUM_NODES 1
|
|
|
|
/*
|
|
* The total number of entries in the page table. Should match the value read
|
|
* from the register APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_SIZE.
|
|
*/
|
|
#define APEX_PAGE_TABLE_TOTAL_ENTRIES 8192
|
|
|
|
#define APEX_EXTENDED_SHIFT 63 /* Extended address bit position. */
|
|
|
|
/* Check reset 120 times */
|
|
#define APEX_RESET_RETRY 120
|
|
/* Wait 100 ms between checks. Total 12 sec wait maximum. */
|
|
#define APEX_RESET_DELAY 100
|
|
|
|
/* Enumeration of the supported sysfs entries. */
|
|
enum sysfs_attribute_type {
|
|
ATTR_KERNEL_HIB_PAGE_TABLE_SIZE,
|
|
ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE,
|
|
ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES,
|
|
};
|
|
|
|
/*
|
|
* Register offsets into BAR2 memory.
|
|
* Only values necessary for driver implementation are defined.
|
|
*/
|
|
enum apex_bar2_regs {
|
|
APEX_BAR2_REG_SCU_BASE = 0x1A300,
|
|
APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_SIZE = 0x46000,
|
|
APEX_BAR2_REG_KERNEL_HIB_EXTENDED_TABLE = 0x46008,
|
|
APEX_BAR2_REG_KERNEL_HIB_TRANSLATION_ENABLE = 0x46010,
|
|
APEX_BAR2_REG_KERNEL_HIB_INSTR_QUEUE_INTVECCTL = 0x46018,
|
|
APEX_BAR2_REG_KERNEL_HIB_INPUT_ACTV_QUEUE_INTVECCTL = 0x46020,
|
|
APEX_BAR2_REG_KERNEL_HIB_PARAM_QUEUE_INTVECCTL = 0x46028,
|
|
APEX_BAR2_REG_KERNEL_HIB_OUTPUT_ACTV_QUEUE_INTVECCTL = 0x46030,
|
|
APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL = 0x46038,
|
|
APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL = 0x46040,
|
|
APEX_BAR2_REG_KERNEL_HIB_FATAL_ERR_INTVECCTL = 0x46048,
|
|
APEX_BAR2_REG_KERNEL_HIB_DMA_PAUSE = 0x46050,
|
|
APEX_BAR2_REG_KERNEL_HIB_DMA_PAUSE_MASK = 0x46058,
|
|
APEX_BAR2_REG_KERNEL_HIB_STATUS_BLOCK_DELAY = 0x46060,
|
|
APEX_BAR2_REG_KERNEL_HIB_MSIX_PENDING_BIT_ARRAY0 = 0x46068,
|
|
APEX_BAR2_REG_KERNEL_HIB_MSIX_PENDING_BIT_ARRAY1 = 0x46070,
|
|
APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_INIT = 0x46078,
|
|
APEX_BAR2_REG_KERNEL_HIB_MSIX_TABLE_INIT = 0x46080,
|
|
APEX_BAR2_REG_KERNEL_WIRE_INT_PENDING_BIT_ARRAY = 0x48778,
|
|
APEX_BAR2_REG_KERNEL_WIRE_INT_MASK_ARRAY = 0x48780,
|
|
APEX_BAR2_REG_USER_HIB_DMA_PAUSE = 0x486D8,
|
|
APEX_BAR2_REG_USER_HIB_DMA_PAUSED = 0x486E0,
|
|
APEX_BAR2_REG_IDLEGENERATOR_IDLEGEN_IDLEREGISTER = 0x4A000,
|
|
APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE = 0x50000,
|
|
|
|
/* Error registers - Used mostly for debug */
|
|
APEX_BAR2_REG_USER_HIB_ERROR_STATUS = 0x86f0,
|
|
APEX_BAR2_REG_SCALAR_CORE_ERROR_STATUS = 0x41a0,
|
|
};
|
|
|
|
/* Addresses for packed registers. */
|
|
#define APEX_BAR2_REG_AXI_QUIESCE (APEX_BAR2_REG_SCU_BASE + 0x2C)
|
|
#define APEX_BAR2_REG_GCB_CLOCK_GATE (APEX_BAR2_REG_SCU_BASE + 0x14)
|
|
#define APEX_BAR2_REG_SCU_0 (APEX_BAR2_REG_SCU_BASE + 0xc)
|
|
#define APEX_BAR2_REG_SCU_1 (APEX_BAR2_REG_SCU_BASE + 0x10)
|
|
#define APEX_BAR2_REG_SCU_2 (APEX_BAR2_REG_SCU_BASE + 0x14)
|
|
#define APEX_BAR2_REG_SCU_3 (APEX_BAR2_REG_SCU_BASE + 0x18)
|
|
#define APEX_BAR2_REG_SCU_4 (APEX_BAR2_REG_SCU_BASE + 0x1c)
|
|
#define APEX_BAR2_REG_SCU_5 (APEX_BAR2_REG_SCU_BASE + 0x20)
|
|
|
|
#define SCU3_RG_PWR_STATE_OVR_BIT_OFFSET 26
|
|
#define SCU3_RG_PWR_STATE_OVR_MASK_WIDTH 2
|
|
#define SCU3_CUR_RST_GCB_BIT_MASK 0x10
|
|
#define SCU2_RG_RST_GCB_BIT_MASK 0xc
|
|
|
|
/* Configuration for page table. */
|
|
static struct gasket_page_table_config apex_page_table_configs[NUM_NODES] = {
|
|
{
|
|
.id = 0,
|
|
.mode = GASKET_PAGE_TABLE_MODE_NORMAL,
|
|
.total_entries = APEX_PAGE_TABLE_TOTAL_ENTRIES,
|
|
.base_reg = APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE,
|
|
.extended_reg = APEX_BAR2_REG_KERNEL_HIB_EXTENDED_TABLE,
|
|
.extended_bit = APEX_EXTENDED_SHIFT,
|
|
},
|
|
};
|
|
|
|
/* The regions in the BAR2 space that can be mapped into user space. */
|
|
static const struct gasket_mappable_region mappable_regions[NUM_REGIONS] = {
|
|
{ 0x40000, 0x1000 },
|
|
{ 0x44000, 0x1000 },
|
|
{ 0x48000, 0x1000 },
|
|
};
|
|
|
|
/* Gasket device interrupts enums must be dense (i.e., no empty slots). */
|
|
enum apex_interrupt {
|
|
APEX_INTERRUPT_INSTR_QUEUE = 0,
|
|
APEX_INTERRUPT_INPUT_ACTV_QUEUE = 1,
|
|
APEX_INTERRUPT_PARAM_QUEUE = 2,
|
|
APEX_INTERRUPT_OUTPUT_ACTV_QUEUE = 3,
|
|
APEX_INTERRUPT_SC_HOST_0 = 4,
|
|
APEX_INTERRUPT_SC_HOST_1 = 5,
|
|
APEX_INTERRUPT_SC_HOST_2 = 6,
|
|
APEX_INTERRUPT_SC_HOST_3 = 7,
|
|
APEX_INTERRUPT_TOP_LEVEL_0 = 8,
|
|
APEX_INTERRUPT_TOP_LEVEL_1 = 9,
|
|
APEX_INTERRUPT_TOP_LEVEL_2 = 10,
|
|
APEX_INTERRUPT_TOP_LEVEL_3 = 11,
|
|
APEX_INTERRUPT_FATAL_ERR = 12,
|
|
APEX_INTERRUPT_COUNT = 13,
|
|
};
|
|
|
|
/* Interrupt descriptors for Apex */
|
|
static struct gasket_interrupt_desc apex_interrupts[] = {
|
|
{
|
|
APEX_INTERRUPT_INSTR_QUEUE,
|
|
APEX_BAR2_REG_KERNEL_HIB_INSTR_QUEUE_INTVECCTL,
|
|
UNPACKED,
|
|
},
|
|
{
|
|
APEX_INTERRUPT_INPUT_ACTV_QUEUE,
|
|
APEX_BAR2_REG_KERNEL_HIB_INPUT_ACTV_QUEUE_INTVECCTL,
|
|
UNPACKED
|
|
},
|
|
{
|
|
APEX_INTERRUPT_PARAM_QUEUE,
|
|
APEX_BAR2_REG_KERNEL_HIB_PARAM_QUEUE_INTVECCTL,
|
|
UNPACKED
|
|
},
|
|
{
|
|
APEX_INTERRUPT_OUTPUT_ACTV_QUEUE,
|
|
APEX_BAR2_REG_KERNEL_HIB_OUTPUT_ACTV_QUEUE_INTVECCTL,
|
|
UNPACKED
|
|
},
|
|
{
|
|
APEX_INTERRUPT_SC_HOST_0,
|
|
APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
|
|
PACK_0
|
|
},
|
|
{
|
|
APEX_INTERRUPT_SC_HOST_1,
|
|
APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
|
|
PACK_1
|
|
},
|
|
{
|
|
APEX_INTERRUPT_SC_HOST_2,
|
|
APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
|
|
PACK_2
|
|
},
|
|
{
|
|
APEX_INTERRUPT_SC_HOST_3,
|
|
APEX_BAR2_REG_KERNEL_HIB_SC_HOST_INTVECCTL,
|
|
PACK_3
|
|
},
|
|
{
|
|
APEX_INTERRUPT_TOP_LEVEL_0,
|
|
APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
|
|
PACK_0
|
|
},
|
|
{
|
|
APEX_INTERRUPT_TOP_LEVEL_1,
|
|
APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
|
|
PACK_1
|
|
},
|
|
{
|
|
APEX_INTERRUPT_TOP_LEVEL_2,
|
|
APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
|
|
PACK_2
|
|
},
|
|
{
|
|
APEX_INTERRUPT_TOP_LEVEL_3,
|
|
APEX_BAR2_REG_KERNEL_HIB_TOP_LEVEL_INTVECCTL,
|
|
PACK_3
|
|
},
|
|
{
|
|
APEX_INTERRUPT_FATAL_ERR,
|
|
APEX_BAR2_REG_KERNEL_HIB_FATAL_ERR_INTVECCTL,
|
|
UNPACKED
|
|
},
|
|
};
|
|
|
|
/* Allows device to enter power save upon driver close(). */
|
|
static int allow_power_save = 1;
|
|
|
|
/* Allows SW based clock gating. */
|
|
static int allow_sw_clock_gating;
|
|
|
|
/* Allows HW based clock gating. */
|
|
/* Note: this is not mutual exclusive with SW clock gating. */
|
|
static int allow_hw_clock_gating = 1;
|
|
|
|
/* Act as if only GCB is instantiated. */
|
|
static int bypass_top_level;
|
|
|
|
module_param(allow_power_save, int, 0644);
|
|
module_param(allow_sw_clock_gating, int, 0644);
|
|
module_param(allow_hw_clock_gating, int, 0644);
|
|
module_param(bypass_top_level, int, 0644);
|
|
|
|
/* Check the device status registers and return device status ALIVE or DEAD. */
|
|
static int apex_get_status(struct gasket_dev *gasket_dev)
|
|
{
|
|
/* TODO: Check device status. */
|
|
return GASKET_STATUS_ALIVE;
|
|
}
|
|
|
|
/* Enter GCB reset state. */
|
|
static int apex_enter_reset(struct gasket_dev *gasket_dev)
|
|
{
|
|
if (bypass_top_level)
|
|
return 0;
|
|
|
|
/*
|
|
* Software reset:
|
|
* Enable sleep mode
|
|
* - Software force GCB idle
|
|
* - Enable GCB idle
|
|
*/
|
|
gasket_read_modify_write_64(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_IDLEGENERATOR_IDLEGEN_IDLEREGISTER,
|
|
0x0, 1, 32);
|
|
|
|
/* - Initiate DMA pause */
|
|
gasket_dev_write_64(gasket_dev, 1, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_USER_HIB_DMA_PAUSE);
|
|
|
|
/* - Wait for DMA pause complete. */
|
|
if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_USER_HIB_DMA_PAUSED, 1, 1,
|
|
APEX_RESET_DELAY, APEX_RESET_RETRY)) {
|
|
dev_err(gasket_dev->dev,
|
|
"DMAs did not quiesce within timeout (%d ms)\n",
|
|
APEX_RESET_RETRY * APEX_RESET_DELAY);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
/* - Enable GCB reset (0x1 to rg_rst_gcb) */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_2, 0x1, 2, 2);
|
|
|
|
/* - Enable GCB clock Gate (0x1 to rg_gated_gcb) */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_2, 0x1, 2, 18);
|
|
|
|
/* - Enable GCB memory shut down (0x3 to rg_force_ram_sd) */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 0x3, 2, 14);
|
|
|
|
/* - Wait for RAM shutdown. */
|
|
if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 1 << 6, 1 << 6,
|
|
APEX_RESET_DELAY, APEX_RESET_RETRY)) {
|
|
dev_err(gasket_dev->dev,
|
|
"RAM did not shut down within timeout (%d ms)\n",
|
|
APEX_RESET_RETRY * APEX_RESET_DELAY);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Quit GCB reset state. */
|
|
static int apex_quit_reset(struct gasket_dev *gasket_dev)
|
|
{
|
|
u32 val0, val1;
|
|
|
|
if (bypass_top_level)
|
|
return 0;
|
|
|
|
/*
|
|
* Disable sleep mode:
|
|
* - Disable GCB memory shut down:
|
|
* - b00: Not forced (HW controlled)
|
|
* - b1x: Force disable
|
|
*/
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 0x0, 2, 14);
|
|
|
|
/*
|
|
* - Disable software clock gate:
|
|
* - b00: Not forced (HW controlled)
|
|
* - b1x: Force disable
|
|
*/
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_2, 0x0, 2, 18);
|
|
|
|
/*
|
|
* - Disable GCB reset (rg_rst_gcb):
|
|
* - b00: Not forced (HW controlled)
|
|
* - b1x: Force disable = Force not Reset
|
|
*/
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_2, 0x2, 2, 2);
|
|
|
|
/* - Wait for RAM enable. */
|
|
if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 1 << 6, 0,
|
|
APEX_RESET_DELAY, APEX_RESET_RETRY)) {
|
|
dev_err(gasket_dev->dev,
|
|
"RAM did not enable within timeout (%d ms)\n",
|
|
APEX_RESET_RETRY * APEX_RESET_DELAY);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
/* - Wait for Reset complete. */
|
|
if (gasket_wait_with_reschedule(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3,
|
|
SCU3_CUR_RST_GCB_BIT_MASK, 0,
|
|
APEX_RESET_DELAY, APEX_RESET_RETRY)) {
|
|
dev_err(gasket_dev->dev,
|
|
"GCB did not leave reset within timeout (%d ms)\n",
|
|
APEX_RESET_RETRY * APEX_RESET_DELAY);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
if (!allow_hw_clock_gating) {
|
|
val0 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3);
|
|
/* Inactive and Sleep mode are disabled. */
|
|
gasket_read_modify_write_32(gasket_dev,
|
|
APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 0x3,
|
|
SCU3_RG_PWR_STATE_OVR_MASK_WIDTH,
|
|
SCU3_RG_PWR_STATE_OVR_BIT_OFFSET);
|
|
val1 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3);
|
|
dev_dbg(gasket_dev->dev,
|
|
"Disallow HW clock gating 0x%x -> 0x%x\n", val0, val1);
|
|
} else {
|
|
val0 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3);
|
|
/* Inactive mode enabled - Sleep mode disabled. */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3, 2,
|
|
SCU3_RG_PWR_STATE_OVR_MASK_WIDTH,
|
|
SCU3_RG_PWR_STATE_OVR_BIT_OFFSET);
|
|
val1 = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3);
|
|
dev_dbg(gasket_dev->dev, "Allow HW clock gating 0x%x -> 0x%x\n",
|
|
val0, val1);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Reset the Apex hardware. Called on final close via device_close_cb. */
|
|
static int apex_device_cleanup(struct gasket_dev *gasket_dev)
|
|
{
|
|
u64 scalar_error;
|
|
u64 hib_error;
|
|
int ret = 0;
|
|
|
|
hib_error = gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_USER_HIB_ERROR_STATUS);
|
|
scalar_error = gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCALAR_CORE_ERROR_STATUS);
|
|
|
|
dev_dbg(gasket_dev->dev,
|
|
"%s 0x%p hib_error 0x%llx scalar_error 0x%llx\n",
|
|
__func__, gasket_dev, hib_error, scalar_error);
|
|
|
|
if (allow_power_save)
|
|
ret = apex_enter_reset(gasket_dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* Determine if GCB is in reset state. */
|
|
static bool is_gcb_in_reset(struct gasket_dev *gasket_dev)
|
|
{
|
|
u32 val = gasket_dev_read_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_SCU_3);
|
|
|
|
/* Masks rg_rst_gcb bit of SCU_CTRL_2 */
|
|
return (val & SCU3_CUR_RST_GCB_BIT_MASK);
|
|
}
|
|
|
|
/* Reset the hardware, then quit reset. Called on device open. */
|
|
static int apex_reset(struct gasket_dev *gasket_dev)
|
|
{
|
|
int ret;
|
|
|
|
if (bypass_top_level)
|
|
return 0;
|
|
|
|
if (!is_gcb_in_reset(gasket_dev)) {
|
|
/* We are not in reset - toggle the reset bit so as to force
|
|
* re-init of custom block
|
|
*/
|
|
dev_dbg(gasket_dev->dev, "%s: toggle reset\n", __func__);
|
|
|
|
ret = apex_enter_reset(gasket_dev);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
ret = apex_quit_reset(gasket_dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Check permissions for Apex ioctls.
|
|
* Returns true if the current user may execute this ioctl, and false otherwise.
|
|
*/
|
|
static bool apex_ioctl_check_permissions(struct file *filp, uint cmd)
|
|
{
|
|
return !!(filp->f_mode & FMODE_WRITE);
|
|
}
|
|
|
|
/* Gates or un-gates Apex clock. */
|
|
static long apex_clock_gating(struct gasket_dev *gasket_dev,
|
|
struct apex_gate_clock_ioctl __user *argp)
|
|
{
|
|
struct apex_gate_clock_ioctl ibuf;
|
|
|
|
if (bypass_top_level || !allow_sw_clock_gating)
|
|
return 0;
|
|
|
|
if (copy_from_user(&ibuf, argp, sizeof(ibuf)))
|
|
return -EFAULT;
|
|
|
|
dev_dbg(gasket_dev->dev, "%s %llu\n", __func__, ibuf.enable);
|
|
|
|
if (ibuf.enable) {
|
|
/* Quiesce AXI, gate GCB clock. */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_AXI_QUIESCE, 0x1, 1,
|
|
16);
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_GCB_CLOCK_GATE, 0x1,
|
|
2, 18);
|
|
} else {
|
|
/* Un-gate GCB clock, un-quiesce AXI. */
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_GCB_CLOCK_GATE, 0x0,
|
|
2, 18);
|
|
gasket_read_modify_write_32(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_AXI_QUIESCE, 0x0, 1,
|
|
16);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* Apex-specific ioctl handler. */
|
|
static long apex_ioctl(struct file *filp, uint cmd, void __user *argp)
|
|
{
|
|
struct gasket_dev *gasket_dev = filp->private_data;
|
|
|
|
if (!apex_ioctl_check_permissions(filp, cmd))
|
|
return -EPERM;
|
|
|
|
switch (cmd) {
|
|
case APEX_IOCTL_GATE_CLOCK:
|
|
return apex_clock_gating(gasket_dev, argp);
|
|
default:
|
|
return -ENOTTY; /* unknown command */
|
|
}
|
|
}
|
|
|
|
/* Display driver sysfs entries. */
|
|
static ssize_t sysfs_show(struct device *device, struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
int ret;
|
|
struct gasket_dev *gasket_dev;
|
|
struct gasket_sysfs_attribute *gasket_attr;
|
|
enum sysfs_attribute_type type;
|
|
|
|
gasket_dev = gasket_sysfs_get_device_data(device);
|
|
if (!gasket_dev) {
|
|
dev_err(device, "No Apex device sysfs mapping found\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
gasket_attr = gasket_sysfs_get_attr(device, attr);
|
|
if (!gasket_attr) {
|
|
dev_err(device, "No Apex device sysfs attr data found\n");
|
|
gasket_sysfs_put_device_data(device, gasket_dev);
|
|
return -ENODEV;
|
|
}
|
|
|
|
type = (enum sysfs_attribute_type)gasket_attr->data.attr_type;
|
|
switch (type) {
|
|
case ATTR_KERNEL_HIB_PAGE_TABLE_SIZE:
|
|
ret = scnprintf(buf, PAGE_SIZE, "%u\n",
|
|
gasket_page_table_num_entries(
|
|
gasket_dev->page_table[0]));
|
|
break;
|
|
case ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE:
|
|
ret = scnprintf(buf, PAGE_SIZE, "%u\n",
|
|
gasket_page_table_num_entries(
|
|
gasket_dev->page_table[0]));
|
|
break;
|
|
case ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES:
|
|
ret = scnprintf(buf, PAGE_SIZE, "%u\n",
|
|
gasket_page_table_num_active_pages(
|
|
gasket_dev->page_table[0]));
|
|
break;
|
|
default:
|
|
dev_dbg(gasket_dev->dev, "Unknown attribute: %s\n",
|
|
attr->attr.name);
|
|
ret = 0;
|
|
break;
|
|
}
|
|
|
|
gasket_sysfs_put_attr(device, gasket_attr);
|
|
gasket_sysfs_put_device_data(device, gasket_dev);
|
|
return ret;
|
|
}
|
|
|
|
static struct gasket_sysfs_attribute apex_sysfs_attrs[] = {
|
|
GASKET_SYSFS_RO(node_0_page_table_entries, sysfs_show,
|
|
ATTR_KERNEL_HIB_PAGE_TABLE_SIZE),
|
|
GASKET_SYSFS_RO(node_0_simple_page_table_entries, sysfs_show,
|
|
ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE),
|
|
GASKET_SYSFS_RO(node_0_num_mapped_pages, sysfs_show,
|
|
ATTR_KERNEL_HIB_NUM_ACTIVE_PAGES),
|
|
GASKET_END_OF_ATTR_ARRAY
|
|
};
|
|
|
|
/* On device open, perform a core reinit reset. */
|
|
static int apex_device_open_cb(struct gasket_dev *gasket_dev)
|
|
{
|
|
return gasket_reset_nolock(gasket_dev);
|
|
}
|
|
|
|
static const struct pci_device_id apex_pci_ids[] = {
|
|
{ PCI_DEVICE(APEX_PCI_VENDOR_ID, APEX_PCI_DEVICE_ID) }, { 0 }
|
|
};
|
|
|
|
static void apex_pci_fixup_class(struct pci_dev *pdev)
|
|
{
|
|
pdev->class = (PCI_CLASS_SYSTEM_OTHER << 8) | pdev->class;
|
|
}
|
|
DECLARE_PCI_FIXUP_CLASS_HEADER(APEX_PCI_VENDOR_ID, APEX_PCI_DEVICE_ID,
|
|
PCI_CLASS_NOT_DEFINED, 8, apex_pci_fixup_class);
|
|
|
|
static int apex_pci_probe(struct pci_dev *pci_dev,
|
|
const struct pci_device_id *id)
|
|
{
|
|
int ret;
|
|
ulong page_table_ready, msix_table_ready;
|
|
int retries = 0;
|
|
struct gasket_dev *gasket_dev;
|
|
|
|
ret = pci_enable_device(pci_dev);
|
|
if (ret) {
|
|
dev_err(&pci_dev->dev, "error enabling PCI device\n");
|
|
return ret;
|
|
}
|
|
|
|
pci_set_master(pci_dev);
|
|
|
|
ret = gasket_pci_add_device(pci_dev, &gasket_dev);
|
|
if (ret) {
|
|
dev_err(&pci_dev->dev, "error adding gasket device\n");
|
|
pci_disable_device(pci_dev);
|
|
return ret;
|
|
}
|
|
|
|
pci_set_drvdata(pci_dev, gasket_dev);
|
|
apex_reset(gasket_dev);
|
|
|
|
while (retries < APEX_RESET_RETRY) {
|
|
page_table_ready =
|
|
gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_KERNEL_HIB_PAGE_TABLE_INIT);
|
|
msix_table_ready =
|
|
gasket_dev_read_64(gasket_dev, APEX_BAR_INDEX,
|
|
APEX_BAR2_REG_KERNEL_HIB_MSIX_TABLE_INIT);
|
|
if (page_table_ready && msix_table_ready)
|
|
break;
|
|
schedule_timeout(msecs_to_jiffies(APEX_RESET_DELAY));
|
|
retries++;
|
|
}
|
|
|
|
if (retries == APEX_RESET_RETRY) {
|
|
if (!page_table_ready)
|
|
dev_err(gasket_dev->dev, "Page table init timed out\n");
|
|
if (!msix_table_ready)
|
|
dev_err(gasket_dev->dev, "MSI-X table init timed out\n");
|
|
ret = -ETIMEDOUT;
|
|
goto remove_device;
|
|
}
|
|
|
|
ret = gasket_sysfs_create_entries(gasket_dev->dev_info.device,
|
|
apex_sysfs_attrs);
|
|
if (ret)
|
|
dev_err(&pci_dev->dev, "error creating device sysfs entries\n");
|
|
|
|
ret = gasket_enable_device(gasket_dev);
|
|
if (ret) {
|
|
dev_err(&pci_dev->dev, "error enabling gasket device\n");
|
|
goto remove_device;
|
|
}
|
|
|
|
/* Place device in low power mode until opened */
|
|
if (allow_power_save)
|
|
apex_enter_reset(gasket_dev);
|
|
|
|
return 0;
|
|
|
|
remove_device:
|
|
gasket_pci_remove_device(pci_dev);
|
|
pci_disable_device(pci_dev);
|
|
return ret;
|
|
}
|
|
|
|
static void apex_pci_remove(struct pci_dev *pci_dev)
|
|
{
|
|
struct gasket_dev *gasket_dev = pci_get_drvdata(pci_dev);
|
|
|
|
gasket_disable_device(gasket_dev);
|
|
gasket_pci_remove_device(pci_dev);
|
|
pci_disable_device(pci_dev);
|
|
}
|
|
|
|
static struct gasket_driver_desc apex_desc = {
|
|
.name = "apex",
|
|
.driver_version = APEX_DRIVER_VERSION,
|
|
.major = 120,
|
|
.minor = 0,
|
|
.module = THIS_MODULE,
|
|
.pci_id_table = apex_pci_ids,
|
|
|
|
.num_page_tables = NUM_NODES,
|
|
.page_table_bar_index = APEX_BAR_INDEX,
|
|
.page_table_configs = apex_page_table_configs,
|
|
.page_table_extended_bit = APEX_EXTENDED_SHIFT,
|
|
|
|
.bar_descriptions = {
|
|
GASKET_UNUSED_BAR,
|
|
GASKET_UNUSED_BAR,
|
|
{ APEX_BAR_BYTES, (VM_WRITE | VM_READ), APEX_BAR_OFFSET,
|
|
NUM_REGIONS, mappable_regions, PCI_BAR },
|
|
GASKET_UNUSED_BAR,
|
|
GASKET_UNUSED_BAR,
|
|
GASKET_UNUSED_BAR,
|
|
},
|
|
.coherent_buffer_description = {
|
|
APEX_CH_MEM_BYTES,
|
|
(VM_WRITE | VM_READ),
|
|
APEX_CM_OFFSET,
|
|
},
|
|
.interrupt_type = PCI_MSIX,
|
|
.interrupt_bar_index = APEX_BAR_INDEX,
|
|
.num_interrupts = APEX_INTERRUPT_COUNT,
|
|
.interrupts = apex_interrupts,
|
|
.interrupt_pack_width = 7,
|
|
|
|
.device_open_cb = apex_device_open_cb,
|
|
.device_close_cb = apex_device_cleanup,
|
|
|
|
.ioctl_handler_cb = apex_ioctl,
|
|
.device_status_cb = apex_get_status,
|
|
.hardware_revision_cb = NULL,
|
|
.device_reset_cb = apex_reset,
|
|
};
|
|
|
|
static struct pci_driver apex_pci_driver = {
|
|
.name = "apex",
|
|
.probe = apex_pci_probe,
|
|
.remove = apex_pci_remove,
|
|
.id_table = apex_pci_ids,
|
|
};
|
|
|
|
static int __init apex_init(void)
|
|
{
|
|
int ret;
|
|
|
|
ret = gasket_register_device(&apex_desc);
|
|
if (ret)
|
|
return ret;
|
|
ret = pci_register_driver(&apex_pci_driver);
|
|
if (ret)
|
|
gasket_unregister_device(&apex_desc);
|
|
return ret;
|
|
}
|
|
|
|
static void apex_exit(void)
|
|
{
|
|
pci_unregister_driver(&apex_pci_driver);
|
|
gasket_unregister_device(&apex_desc);
|
|
}
|
|
MODULE_DESCRIPTION("Google Apex driver");
|
|
MODULE_VERSION(APEX_DRIVER_VERSION);
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_AUTHOR("John Joseph <jnjoseph@google.com>");
|
|
MODULE_DEVICE_TABLE(pci, apex_pci_ids);
|
|
module_init(apex_init);
|
|
module_exit(apex_exit);
|