![Douglas Anderson](/assets/img/avatar_default.png)
Some of the platform-specific stuff in rockchip_dp_poweron() needs to happen before the generic code. Some needs to happen after. Let's split the callback in two. Specifically we can't start doing PSR work until _after_ the whole controller is up, so don't set the enable until the end. Cc: Kristian H. Kristensen <hoegsberg@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> [seanpaul added exynos change] Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-23-enric.balletbo@collabora.com
1738 lines
43 KiB
C
1738 lines
43 KiB
C
/*
|
|
* Analogix DP (Display Port) core interface driver.
|
|
*
|
|
* Copyright (C) 2012 Samsung Electronics Co., Ltd.
|
|
* Author: Jingoo Han <jg1.han@samsung.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/err.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_gpio.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/component.h>
|
|
#include <linux/phy/phy.h>
|
|
|
|
#include <drm/drmP.h>
|
|
#include <drm/drm_atomic_helper.h>
|
|
#include <drm/drm_crtc.h>
|
|
#include <drm/drm_crtc_helper.h>
|
|
#include <drm/drm_panel.h>
|
|
|
|
#include <drm/bridge/analogix_dp.h>
|
|
|
|
#include "analogix_dp_core.h"
|
|
#include "analogix_dp_reg.h"
|
|
|
|
#define to_dp(nm) container_of(nm, struct analogix_dp_device, nm)
|
|
|
|
static const bool verify_fast_training;
|
|
|
|
struct bridge_init {
|
|
struct i2c_client *client;
|
|
struct device_node *node;
|
|
};
|
|
|
|
static int analogix_dp_init_dp(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
|
|
analogix_dp_reset(dp);
|
|
|
|
analogix_dp_swreset(dp);
|
|
|
|
analogix_dp_init_analog_param(dp);
|
|
analogix_dp_init_interrupt(dp);
|
|
|
|
/* SW defined function Normal operation */
|
|
analogix_dp_enable_sw_function(dp);
|
|
|
|
analogix_dp_config_interrupt(dp);
|
|
ret = analogix_dp_init_analog_func(dp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
analogix_dp_init_hpd(dp);
|
|
analogix_dp_init_aux(dp);
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_detect_hpd(struct analogix_dp_device *dp)
|
|
{
|
|
int timeout_loop = 0;
|
|
|
|
while (timeout_loop < DP_TIMEOUT_LOOP_COUNT) {
|
|
if (analogix_dp_get_plug_in_status(dp) == 0)
|
|
return 0;
|
|
|
|
timeout_loop++;
|
|
usleep_range(1000, 1100);
|
|
}
|
|
|
|
/*
|
|
* Some edp screen do not have hpd signal, so we can't just
|
|
* return failed when hpd plug in detect failed, DT property
|
|
* "force-hpd" would indicate whether driver need this.
|
|
*/
|
|
if (!dp->force_hpd)
|
|
return -ETIMEDOUT;
|
|
|
|
/*
|
|
* The eDP TRM indicate that if HPD_STATUS(RO) is 0, AUX CH
|
|
* will not work, so we need to give a force hpd action to
|
|
* set HPD_STATUS manually.
|
|
*/
|
|
dev_dbg(dp->dev, "failed to get hpd plug status, try to force hpd\n");
|
|
|
|
analogix_dp_force_hpd(dp);
|
|
|
|
if (analogix_dp_get_plug_in_status(dp) != 0) {
|
|
dev_err(dp->dev, "failed to get hpd plug in status\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
dev_dbg(dp->dev, "success to get plug in status after force hpd\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int analogix_dp_psr_enabled(struct analogix_dp_device *dp)
|
|
{
|
|
|
|
return dp->psr_enable;
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_psr_enabled);
|
|
|
|
int analogix_dp_enable_psr(struct analogix_dp_device *dp)
|
|
{
|
|
struct edp_vsc_psr psr_vsc;
|
|
|
|
if (!dp->psr_enable)
|
|
return 0;
|
|
|
|
/* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */
|
|
memset(&psr_vsc, 0, sizeof(psr_vsc));
|
|
psr_vsc.sdp_header.HB0 = 0;
|
|
psr_vsc.sdp_header.HB1 = 0x7;
|
|
psr_vsc.sdp_header.HB2 = 0x2;
|
|
psr_vsc.sdp_header.HB3 = 0x8;
|
|
|
|
psr_vsc.DB0 = 0;
|
|
psr_vsc.DB1 = EDP_VSC_PSR_STATE_ACTIVE | EDP_VSC_PSR_CRC_VALUES_VALID;
|
|
|
|
return analogix_dp_send_psr_spd(dp, &psr_vsc, true);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_enable_psr);
|
|
|
|
int analogix_dp_disable_psr(struct analogix_dp_device *dp)
|
|
{
|
|
struct edp_vsc_psr psr_vsc;
|
|
int ret;
|
|
|
|
if (!dp->psr_enable)
|
|
return 0;
|
|
|
|
/* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */
|
|
memset(&psr_vsc, 0, sizeof(psr_vsc));
|
|
psr_vsc.sdp_header.HB0 = 0;
|
|
psr_vsc.sdp_header.HB1 = 0x7;
|
|
psr_vsc.sdp_header.HB2 = 0x2;
|
|
psr_vsc.sdp_header.HB3 = 0x8;
|
|
|
|
psr_vsc.DB0 = 0;
|
|
psr_vsc.DB1 = 0;
|
|
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
return analogix_dp_send_psr_spd(dp, &psr_vsc, false);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_disable_psr);
|
|
|
|
static int analogix_dp_detect_sink_psr(struct analogix_dp_device *dp)
|
|
{
|
|
unsigned char psr_version;
|
|
int ret;
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_SUPPORT, &psr_version);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to get PSR version, disable it\n");
|
|
return ret;
|
|
}
|
|
|
|
dev_dbg(dp->dev, "Panel PSR version : %x\n", psr_version);
|
|
|
|
dp->psr_enable = (psr_version & DP_PSR_IS_SUPPORTED) ? true : false;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_enable_sink_psr(struct analogix_dp_device *dp)
|
|
{
|
|
unsigned char psr_en;
|
|
int ret;
|
|
|
|
/* Disable psr function */
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_EN_CFG, &psr_en);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to get psr config\n");
|
|
goto end;
|
|
}
|
|
|
|
psr_en &= ~DP_PSR_ENABLE;
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to disable panel psr\n");
|
|
goto end;
|
|
}
|
|
|
|
/* Main-Link transmitter remains active during PSR active states */
|
|
psr_en = DP_PSR_MAIN_LINK_ACTIVE | DP_PSR_CRC_VERIFICATION;
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to set panel psr\n");
|
|
goto end;
|
|
}
|
|
|
|
/* Enable psr function */
|
|
psr_en = DP_PSR_ENABLE | DP_PSR_MAIN_LINK_ACTIVE |
|
|
DP_PSR_CRC_VERIFICATION;
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to set panel psr\n");
|
|
goto end;
|
|
}
|
|
|
|
analogix_dp_enable_psr_crc(dp);
|
|
|
|
return 0;
|
|
end:
|
|
dev_err(dp->dev, "enable psr fail, force to disable psr\n");
|
|
dp->psr_enable = false;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int
|
|
analogix_dp_enable_rx_to_enhanced_mode(struct analogix_dp_device *dp,
|
|
bool enable)
|
|
{
|
|
u8 data;
|
|
int ret;
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
|
|
if (ret != 1)
|
|
return ret;
|
|
|
|
if (enable)
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
|
|
DP_LANE_COUNT_ENHANCED_FRAME_EN |
|
|
DPCD_LANE_COUNT_SET(data));
|
|
else
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
|
|
DPCD_LANE_COUNT_SET(data));
|
|
|
|
return ret < 0 ? ret : 0;
|
|
}
|
|
|
|
static int analogix_dp_is_enhanced_mode_available(struct analogix_dp_device *dp,
|
|
u8 *enhanced_mode_support)
|
|
{
|
|
u8 data;
|
|
int ret;
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data);
|
|
if (ret != 1) {
|
|
*enhanced_mode_support = 0;
|
|
return ret;
|
|
}
|
|
|
|
*enhanced_mode_support = DPCD_ENHANCED_FRAME_CAP(data);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_set_enhanced_mode(struct analogix_dp_device *dp)
|
|
{
|
|
u8 data;
|
|
int ret;
|
|
|
|
ret = analogix_dp_is_enhanced_mode_available(dp, &data);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = analogix_dp_enable_rx_to_enhanced_mode(dp, data);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
analogix_dp_enable_enhanced_mode(dp, data);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_training_pattern_dis(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
|
|
analogix_dp_set_training_pattern(dp, DP_NONE);
|
|
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
DP_TRAINING_PATTERN_DISABLE);
|
|
|
|
return ret < 0 ? ret : 0;
|
|
}
|
|
|
|
static void
|
|
analogix_dp_set_lane_lane_pre_emphasis(struct analogix_dp_device *dp,
|
|
int pre_emphasis, int lane)
|
|
{
|
|
switch (lane) {
|
|
case 0:
|
|
analogix_dp_set_lane0_pre_emphasis(dp, pre_emphasis);
|
|
break;
|
|
case 1:
|
|
analogix_dp_set_lane1_pre_emphasis(dp, pre_emphasis);
|
|
break;
|
|
|
|
case 2:
|
|
analogix_dp_set_lane2_pre_emphasis(dp, pre_emphasis);
|
|
break;
|
|
|
|
case 3:
|
|
analogix_dp_set_lane3_pre_emphasis(dp, pre_emphasis);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static int analogix_dp_link_start(struct analogix_dp_device *dp)
|
|
{
|
|
u8 buf[4];
|
|
int lane, lane_count, pll_tries, retval;
|
|
|
|
lane_count = dp->link_train.lane_count;
|
|
|
|
dp->link_train.lt_state = CLOCK_RECOVERY;
|
|
dp->link_train.eq_loop = 0;
|
|
|
|
for (lane = 0; lane < lane_count; lane++)
|
|
dp->link_train.cr_loop[lane] = 0;
|
|
|
|
/* Set link rate and count as you want to establish*/
|
|
analogix_dp_set_link_bandwidth(dp, dp->link_train.link_rate);
|
|
analogix_dp_set_lane_count(dp, dp->link_train.lane_count);
|
|
|
|
/* Setup RX configuration */
|
|
buf[0] = dp->link_train.link_rate;
|
|
buf[1] = dp->link_train.lane_count;
|
|
retval = drm_dp_dpcd_write(&dp->aux, DP_LINK_BW_SET, buf, 2);
|
|
if (retval < 0)
|
|
return retval;
|
|
/* set enhanced mode if available */
|
|
retval = analogix_dp_set_enhanced_mode(dp);
|
|
if (retval < 0) {
|
|
dev_err(dp->dev, "failed to set enhance mode\n");
|
|
return retval;
|
|
}
|
|
|
|
/* Set TX pre-emphasis to minimum */
|
|
for (lane = 0; lane < lane_count; lane++)
|
|
analogix_dp_set_lane_lane_pre_emphasis(dp,
|
|
PRE_EMPHASIS_LEVEL_0, lane);
|
|
|
|
/* Wait for PLL lock */
|
|
pll_tries = 0;
|
|
while (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) {
|
|
if (pll_tries == DP_TIMEOUT_LOOP_COUNT) {
|
|
dev_err(dp->dev, "Wait for PLL lock timed out\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
pll_tries++;
|
|
usleep_range(90, 120);
|
|
}
|
|
|
|
/* Set training pattern 1 */
|
|
analogix_dp_set_training_pattern(dp, TRAINING_PTN1);
|
|
|
|
/* Set RX training pattern */
|
|
retval = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
DP_LINK_SCRAMBLING_DISABLE |
|
|
DP_TRAINING_PATTERN_1);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
for (lane = 0; lane < lane_count; lane++)
|
|
buf[lane] = DP_TRAIN_PRE_EMPH_LEVEL_0 |
|
|
DP_TRAIN_VOLTAGE_SWING_LEVEL_0;
|
|
|
|
retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, buf,
|
|
lane_count);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned char analogix_dp_get_lane_status(u8 link_status[2], int lane)
|
|
{
|
|
int shift = (lane & 1) * 4;
|
|
u8 link_value = link_status[lane >> 1];
|
|
|
|
return (link_value >> shift) & 0xf;
|
|
}
|
|
|
|
static int analogix_dp_clock_recovery_ok(u8 link_status[2], int lane_count)
|
|
{
|
|
int lane;
|
|
u8 lane_status;
|
|
|
|
for (lane = 0; lane < lane_count; lane++) {
|
|
lane_status = analogix_dp_get_lane_status(link_status, lane);
|
|
if ((lane_status & DP_LANE_CR_DONE) == 0)
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_channel_eq_ok(u8 link_status[2], u8 link_align,
|
|
int lane_count)
|
|
{
|
|
int lane;
|
|
u8 lane_status;
|
|
|
|
if ((link_align & DP_INTERLANE_ALIGN_DONE) == 0)
|
|
return -EINVAL;
|
|
|
|
for (lane = 0; lane < lane_count; lane++) {
|
|
lane_status = analogix_dp_get_lane_status(link_status, lane);
|
|
lane_status &= DP_CHANNEL_EQ_BITS;
|
|
if (lane_status != DP_CHANNEL_EQ_BITS)
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned char
|
|
analogix_dp_get_adjust_request_voltage(u8 adjust_request[2], int lane)
|
|
{
|
|
int shift = (lane & 1) * 4;
|
|
u8 link_value = adjust_request[lane >> 1];
|
|
|
|
return (link_value >> shift) & 0x3;
|
|
}
|
|
|
|
static unsigned char analogix_dp_get_adjust_request_pre_emphasis(
|
|
u8 adjust_request[2],
|
|
int lane)
|
|
{
|
|
int shift = (lane & 1) * 4;
|
|
u8 link_value = adjust_request[lane >> 1];
|
|
|
|
return ((link_value >> shift) & 0xc) >> 2;
|
|
}
|
|
|
|
static void analogix_dp_set_lane_link_training(struct analogix_dp_device *dp,
|
|
u8 training_lane_set, int lane)
|
|
{
|
|
switch (lane) {
|
|
case 0:
|
|
analogix_dp_set_lane0_link_training(dp, training_lane_set);
|
|
break;
|
|
case 1:
|
|
analogix_dp_set_lane1_link_training(dp, training_lane_set);
|
|
break;
|
|
|
|
case 2:
|
|
analogix_dp_set_lane2_link_training(dp, training_lane_set);
|
|
break;
|
|
|
|
case 3:
|
|
analogix_dp_set_lane3_link_training(dp, training_lane_set);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static unsigned int
|
|
analogix_dp_get_lane_link_training(struct analogix_dp_device *dp,
|
|
int lane)
|
|
{
|
|
u32 reg;
|
|
|
|
switch (lane) {
|
|
case 0:
|
|
reg = analogix_dp_get_lane0_link_training(dp);
|
|
break;
|
|
case 1:
|
|
reg = analogix_dp_get_lane1_link_training(dp);
|
|
break;
|
|
case 2:
|
|
reg = analogix_dp_get_lane2_link_training(dp);
|
|
break;
|
|
case 3:
|
|
reg = analogix_dp_get_lane3_link_training(dp);
|
|
break;
|
|
default:
|
|
WARN_ON(1);
|
|
return 0;
|
|
}
|
|
|
|
return reg;
|
|
}
|
|
|
|
static void analogix_dp_reduce_link_rate(struct analogix_dp_device *dp)
|
|
{
|
|
analogix_dp_training_pattern_dis(dp);
|
|
analogix_dp_set_enhanced_mode(dp);
|
|
|
|
dp->link_train.lt_state = FAILED;
|
|
}
|
|
|
|
static void analogix_dp_get_adjust_training_lane(struct analogix_dp_device *dp,
|
|
u8 adjust_request[2])
|
|
{
|
|
int lane, lane_count;
|
|
u8 voltage_swing, pre_emphasis, training_lane;
|
|
|
|
lane_count = dp->link_train.lane_count;
|
|
for (lane = 0; lane < lane_count; lane++) {
|
|
voltage_swing = analogix_dp_get_adjust_request_voltage(
|
|
adjust_request, lane);
|
|
pre_emphasis = analogix_dp_get_adjust_request_pre_emphasis(
|
|
adjust_request, lane);
|
|
training_lane = DPCD_VOLTAGE_SWING_SET(voltage_swing) |
|
|
DPCD_PRE_EMPHASIS_SET(pre_emphasis);
|
|
|
|
if (voltage_swing == VOLTAGE_LEVEL_3)
|
|
training_lane |= DP_TRAIN_MAX_SWING_REACHED;
|
|
if (pre_emphasis == PRE_EMPHASIS_LEVEL_3)
|
|
training_lane |= DP_TRAIN_MAX_PRE_EMPHASIS_REACHED;
|
|
|
|
dp->link_train.training_lane[lane] = training_lane;
|
|
}
|
|
}
|
|
|
|
static int analogix_dp_process_clock_recovery(struct analogix_dp_device *dp)
|
|
{
|
|
int lane, lane_count, retval;
|
|
u8 voltage_swing, pre_emphasis, training_lane;
|
|
u8 link_status[2], adjust_request[2];
|
|
|
|
usleep_range(100, 101);
|
|
|
|
lane_count = dp->link_train.lane_count;
|
|
|
|
retval = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status, 2);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
retval = drm_dp_dpcd_read(&dp->aux, DP_ADJUST_REQUEST_LANE0_1,
|
|
adjust_request, 2);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
if (analogix_dp_clock_recovery_ok(link_status, lane_count) == 0) {
|
|
/* set training pattern 2 for EQ */
|
|
analogix_dp_set_training_pattern(dp, TRAINING_PTN2);
|
|
|
|
retval = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
DP_LINK_SCRAMBLING_DISABLE |
|
|
DP_TRAINING_PATTERN_2);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
dev_info(dp->dev, "Link Training Clock Recovery success\n");
|
|
dp->link_train.lt_state = EQUALIZER_TRAINING;
|
|
} else {
|
|
for (lane = 0; lane < lane_count; lane++) {
|
|
training_lane = analogix_dp_get_lane_link_training(
|
|
dp, lane);
|
|
voltage_swing = analogix_dp_get_adjust_request_voltage(
|
|
adjust_request, lane);
|
|
pre_emphasis = analogix_dp_get_adjust_request_pre_emphasis(
|
|
adjust_request, lane);
|
|
|
|
if (DPCD_VOLTAGE_SWING_GET(training_lane) ==
|
|
voltage_swing &&
|
|
DPCD_PRE_EMPHASIS_GET(training_lane) ==
|
|
pre_emphasis)
|
|
dp->link_train.cr_loop[lane]++;
|
|
|
|
if (dp->link_train.cr_loop[lane] == MAX_CR_LOOP ||
|
|
voltage_swing == VOLTAGE_LEVEL_3 ||
|
|
pre_emphasis == PRE_EMPHASIS_LEVEL_3) {
|
|
dev_err(dp->dev, "CR Max reached (%d,%d,%d)\n",
|
|
dp->link_train.cr_loop[lane],
|
|
voltage_swing, pre_emphasis);
|
|
analogix_dp_reduce_link_rate(dp);
|
|
return -EIO;
|
|
}
|
|
}
|
|
}
|
|
|
|
analogix_dp_get_adjust_training_lane(dp, adjust_request);
|
|
|
|
for (lane = 0; lane < lane_count; lane++)
|
|
analogix_dp_set_lane_link_training(dp,
|
|
dp->link_train.training_lane[lane], lane);
|
|
|
|
retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET,
|
|
dp->link_train.training_lane, lane_count);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
|
|
{
|
|
int lane, lane_count, retval;
|
|
u32 reg;
|
|
u8 link_align, link_status[2], adjust_request[2];
|
|
|
|
usleep_range(400, 401);
|
|
|
|
lane_count = dp->link_train.lane_count;
|
|
|
|
retval = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status, 2);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
if (analogix_dp_clock_recovery_ok(link_status, lane_count)) {
|
|
analogix_dp_reduce_link_rate(dp);
|
|
return -EIO;
|
|
}
|
|
|
|
retval = drm_dp_dpcd_read(&dp->aux, DP_ADJUST_REQUEST_LANE0_1,
|
|
adjust_request, 2);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
retval = drm_dp_dpcd_readb(&dp->aux, DP_LANE_ALIGN_STATUS_UPDATED,
|
|
&link_align);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
analogix_dp_get_adjust_training_lane(dp, adjust_request);
|
|
|
|
if (!analogix_dp_channel_eq_ok(link_status, link_align, lane_count)) {
|
|
/* traing pattern Set to Normal */
|
|
retval = analogix_dp_training_pattern_dis(dp);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
dev_info(dp->dev, "Link Training success!\n");
|
|
analogix_dp_get_link_bandwidth(dp, ®);
|
|
dp->link_train.link_rate = reg;
|
|
dev_dbg(dp->dev, "final bandwidth = %.2x\n",
|
|
dp->link_train.link_rate);
|
|
|
|
analogix_dp_get_lane_count(dp, ®);
|
|
dp->link_train.lane_count = reg;
|
|
dev_dbg(dp->dev, "final lane count = %.2x\n",
|
|
dp->link_train.lane_count);
|
|
|
|
dp->link_train.lt_state = FINISHED;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* not all locked */
|
|
dp->link_train.eq_loop++;
|
|
|
|
if (dp->link_train.eq_loop > MAX_EQ_LOOP) {
|
|
dev_err(dp->dev, "EQ Max loop\n");
|
|
analogix_dp_reduce_link_rate(dp);
|
|
return -EIO;
|
|
}
|
|
|
|
for (lane = 0; lane < lane_count; lane++)
|
|
analogix_dp_set_lane_link_training(dp,
|
|
dp->link_train.training_lane[lane], lane);
|
|
|
|
retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET,
|
|
dp->link_train.training_lane, lane_count);
|
|
if (retval < 0)
|
|
return retval;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void analogix_dp_get_max_rx_bandwidth(struct analogix_dp_device *dp,
|
|
u8 *bandwidth)
|
|
{
|
|
u8 data;
|
|
|
|
/*
|
|
* For DP rev.1.1, Maximum link rate of Main Link lanes
|
|
* 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps
|
|
* For DP rev.1.2, Maximum link rate of Main Link lanes
|
|
* 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps, 0x14 = 5.4Gbps
|
|
*/
|
|
drm_dp_dpcd_readb(&dp->aux, DP_MAX_LINK_RATE, &data);
|
|
*bandwidth = data;
|
|
}
|
|
|
|
static void analogix_dp_get_max_rx_lane_count(struct analogix_dp_device *dp,
|
|
u8 *lane_count)
|
|
{
|
|
u8 data;
|
|
|
|
/*
|
|
* For DP rev.1.1, Maximum number of Main Link lanes
|
|
* 0x01 = 1 lane, 0x02 = 2 lanes, 0x04 = 4 lanes
|
|
*/
|
|
drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data);
|
|
*lane_count = DPCD_MAX_LANE_COUNT(data);
|
|
}
|
|
|
|
static int analogix_dp_full_link_train(struct analogix_dp_device *dp,
|
|
u32 max_lanes, u32 max_rate)
|
|
{
|
|
int retval = 0;
|
|
bool training_finished = false;
|
|
|
|
/*
|
|
* MACRO_RST must be applied after the PLL_LOCK to avoid
|
|
* the DP inter pair skew issue for at least 10 us
|
|
*/
|
|
analogix_dp_reset_macro(dp);
|
|
|
|
/* Initialize by reading RX's DPCD */
|
|
analogix_dp_get_max_rx_bandwidth(dp, &dp->link_train.link_rate);
|
|
analogix_dp_get_max_rx_lane_count(dp, &dp->link_train.lane_count);
|
|
|
|
if ((dp->link_train.link_rate != DP_LINK_BW_1_62) &&
|
|
(dp->link_train.link_rate != DP_LINK_BW_2_7) &&
|
|
(dp->link_train.link_rate != DP_LINK_BW_5_4)) {
|
|
dev_err(dp->dev, "Rx Max Link Rate is abnormal :%x !\n",
|
|
dp->link_train.link_rate);
|
|
dp->link_train.link_rate = DP_LINK_BW_1_62;
|
|
}
|
|
|
|
if (dp->link_train.lane_count == 0) {
|
|
dev_err(dp->dev, "Rx Max Lane count is abnormal :%x !\n",
|
|
dp->link_train.lane_count);
|
|
dp->link_train.lane_count = (u8)LANE_COUNT1;
|
|
}
|
|
|
|
/* Setup TX lane count & rate */
|
|
if (dp->link_train.lane_count > max_lanes)
|
|
dp->link_train.lane_count = max_lanes;
|
|
if (dp->link_train.link_rate > max_rate)
|
|
dp->link_train.link_rate = max_rate;
|
|
|
|
/* All DP analog module power up */
|
|
analogix_dp_set_analog_power_down(dp, POWER_ALL, 0);
|
|
|
|
dp->link_train.lt_state = START;
|
|
|
|
/* Process here */
|
|
while (!retval && !training_finished) {
|
|
switch (dp->link_train.lt_state) {
|
|
case START:
|
|
retval = analogix_dp_link_start(dp);
|
|
if (retval)
|
|
dev_err(dp->dev, "LT link start failed!\n");
|
|
break;
|
|
case CLOCK_RECOVERY:
|
|
retval = analogix_dp_process_clock_recovery(dp);
|
|
if (retval)
|
|
dev_err(dp->dev, "LT CR failed!\n");
|
|
break;
|
|
case EQUALIZER_TRAINING:
|
|
retval = analogix_dp_process_equalizer_training(dp);
|
|
if (retval)
|
|
dev_err(dp->dev, "LT EQ failed!\n");
|
|
break;
|
|
case FINISHED:
|
|
training_finished = 1;
|
|
break;
|
|
case FAILED:
|
|
return -EREMOTEIO;
|
|
}
|
|
}
|
|
if (retval)
|
|
dev_err(dp->dev, "eDP link training failed (%d)\n", retval);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static int analogix_dp_fast_link_train(struct analogix_dp_device *dp)
|
|
{
|
|
int i, ret;
|
|
u8 link_align, link_status[2];
|
|
enum pll_status status;
|
|
|
|
analogix_dp_reset_macro(dp);
|
|
|
|
analogix_dp_set_link_bandwidth(dp, dp->link_train.link_rate);
|
|
analogix_dp_set_lane_count(dp, dp->link_train.lane_count);
|
|
|
|
for (i = 0; i < dp->link_train.lane_count; i++) {
|
|
analogix_dp_set_lane_link_training(dp,
|
|
dp->link_train.training_lane[i], i);
|
|
}
|
|
|
|
ret = readx_poll_timeout(analogix_dp_get_pll_lock_status, dp, status,
|
|
status != PLL_UNLOCKED, 120,
|
|
120 * DP_TIMEOUT_LOOP_COUNT);
|
|
if (ret) {
|
|
DRM_DEV_ERROR(dp->dev, "Wait for pll lock failed %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
/* source Set training pattern 1 */
|
|
analogix_dp_set_training_pattern(dp, TRAINING_PTN1);
|
|
/* From DP spec, pattern must be on-screen for a minimum 500us */
|
|
usleep_range(500, 600);
|
|
|
|
analogix_dp_set_training_pattern(dp, TRAINING_PTN2);
|
|
/* From DP spec, pattern must be on-screen for a minimum 500us */
|
|
usleep_range(500, 600);
|
|
|
|
/* TODO: enhanced_mode?*/
|
|
analogix_dp_set_training_pattern(dp, DP_NONE);
|
|
|
|
/*
|
|
* Useful for debugging issues with fast link training, disable for more
|
|
* speed
|
|
*/
|
|
if (verify_fast_training) {
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_ALIGN_STATUS_UPDATED,
|
|
&link_align);
|
|
if (ret < 0) {
|
|
DRM_DEV_ERROR(dp->dev, "Read align status failed %d\n",
|
|
ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status,
|
|
2);
|
|
if (ret < 0) {
|
|
DRM_DEV_ERROR(dp->dev, "Read link status failed %d\n",
|
|
ret);
|
|
return ret;
|
|
}
|
|
|
|
if (analogix_dp_clock_recovery_ok(link_status,
|
|
dp->link_train.lane_count)) {
|
|
DRM_DEV_ERROR(dp->dev, "Clock recovery failed\n");
|
|
analogix_dp_reduce_link_rate(dp);
|
|
return -EIO;
|
|
}
|
|
|
|
if (analogix_dp_channel_eq_ok(link_status, link_align,
|
|
dp->link_train.lane_count)) {
|
|
DRM_DEV_ERROR(dp->dev, "Channel EQ failed\n");
|
|
analogix_dp_reduce_link_rate(dp);
|
|
return -EIO;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_train_link(struct analogix_dp_device *dp)
|
|
{
|
|
if (dp->fast_train_enable)
|
|
return analogix_dp_fast_link_train(dp);
|
|
|
|
return analogix_dp_full_link_train(dp, dp->video_info.max_lane_count,
|
|
dp->video_info.max_link_rate);
|
|
}
|
|
|
|
static int analogix_dp_config_video(struct analogix_dp_device *dp)
|
|
{
|
|
int timeout_loop = 0;
|
|
int done_count = 0;
|
|
|
|
analogix_dp_config_video_slave_mode(dp);
|
|
|
|
analogix_dp_set_video_color_format(dp);
|
|
|
|
if (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) {
|
|
dev_err(dp->dev, "PLL is not locked yet.\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
for (;;) {
|
|
timeout_loop++;
|
|
if (analogix_dp_is_slave_video_stream_clock_on(dp) == 0)
|
|
break;
|
|
if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) {
|
|
dev_err(dp->dev, "Timeout of slave video streamclk ok\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
usleep_range(1000, 1001);
|
|
}
|
|
|
|
/* Set to use the register calculated M/N video */
|
|
analogix_dp_set_video_cr_mn(dp, CALCULATED_M, 0, 0);
|
|
|
|
/* For video bist, Video timing must be generated by register */
|
|
analogix_dp_set_video_timing_mode(dp, VIDEO_TIMING_FROM_CAPTURE);
|
|
|
|
/* Disable video mute */
|
|
analogix_dp_enable_video_mute(dp, 0);
|
|
|
|
/* Configure video slave mode */
|
|
analogix_dp_enable_video_master(dp, 0);
|
|
|
|
/* Enable video */
|
|
analogix_dp_start_video(dp);
|
|
|
|
timeout_loop = 0;
|
|
|
|
for (;;) {
|
|
timeout_loop++;
|
|
if (analogix_dp_is_video_stream_on(dp) == 0) {
|
|
done_count++;
|
|
if (done_count > 10)
|
|
break;
|
|
} else if (done_count) {
|
|
done_count = 0;
|
|
}
|
|
if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) {
|
|
dev_warn(dp->dev,
|
|
"Ignoring timeout of video streamclk ok\n");
|
|
break;
|
|
}
|
|
|
|
usleep_range(1000, 1001);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_enable_scramble(struct analogix_dp_device *dp,
|
|
bool enable)
|
|
{
|
|
u8 data;
|
|
int ret;
|
|
|
|
if (enable) {
|
|
analogix_dp_enable_scrambling(dp);
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
&data);
|
|
if (ret != 1)
|
|
return ret;
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
(u8)(data & ~DP_LINK_SCRAMBLING_DISABLE));
|
|
} else {
|
|
analogix_dp_disable_scrambling(dp);
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
&data);
|
|
if (ret != 1)
|
|
return ret;
|
|
ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
|
|
(u8)(data | DP_LINK_SCRAMBLING_DISABLE));
|
|
}
|
|
return ret < 0 ? ret : 0;
|
|
}
|
|
|
|
static irqreturn_t analogix_dp_hardirq(int irq, void *arg)
|
|
{
|
|
struct analogix_dp_device *dp = arg;
|
|
irqreturn_t ret = IRQ_NONE;
|
|
enum dp_irq_type irq_type;
|
|
|
|
irq_type = analogix_dp_get_irq_type(dp);
|
|
if (irq_type != DP_IRQ_TYPE_UNKNOWN) {
|
|
analogix_dp_mute_hpd_interrupt(dp);
|
|
ret = IRQ_WAKE_THREAD;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static irqreturn_t analogix_dp_irq_thread(int irq, void *arg)
|
|
{
|
|
struct analogix_dp_device *dp = arg;
|
|
enum dp_irq_type irq_type;
|
|
|
|
irq_type = analogix_dp_get_irq_type(dp);
|
|
if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN ||
|
|
irq_type & DP_IRQ_TYPE_HP_CABLE_OUT) {
|
|
dev_dbg(dp->dev, "Detected cable status changed!\n");
|
|
if (dp->drm_dev)
|
|
drm_helper_hpd_irq_event(dp->drm_dev);
|
|
}
|
|
|
|
if (irq_type != DP_IRQ_TYPE_UNKNOWN) {
|
|
analogix_dp_clear_hotplug_interrupts(dp);
|
|
analogix_dp_unmute_hpd_interrupt(dp);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int analogix_dp_fast_link_train_detection(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
u8 spread;
|
|
|
|
ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_DOWNSPREAD, &spread);
|
|
if (ret != 1) {
|
|
dev_err(dp->dev, "failed to read downspread %d\n", ret);
|
|
return ret;
|
|
}
|
|
dp->fast_train_enable = !!(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING);
|
|
dev_dbg(dp->dev, "fast link training %s\n",
|
|
dp->fast_train_enable ? "supported" : "unsupported");
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_commit(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
|
|
/* Keep the panel disabled while we configure video */
|
|
if (dp->plat_data->panel) {
|
|
if (drm_panel_disable(dp->plat_data->panel))
|
|
DRM_ERROR("failed to disable the panel\n");
|
|
}
|
|
|
|
ret = analogix_dp_train_link(dp);
|
|
if (ret) {
|
|
dev_err(dp->dev, "unable to do link train, ret=%d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = analogix_dp_enable_scramble(dp, 1);
|
|
if (ret < 0) {
|
|
dev_err(dp->dev, "can not enable scramble\n");
|
|
return ret;
|
|
}
|
|
|
|
analogix_dp_init_video(dp);
|
|
ret = analogix_dp_config_video(dp);
|
|
if (ret) {
|
|
dev_err(dp->dev, "unable to config video\n");
|
|
return ret;
|
|
}
|
|
|
|
/* Safe to enable the panel now */
|
|
if (dp->plat_data->panel) {
|
|
ret = drm_panel_enable(dp->plat_data->panel);
|
|
if (ret) {
|
|
DRM_ERROR("failed to enable the panel\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = analogix_dp_detect_sink_psr(dp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (dp->psr_enable) {
|
|
ret = analogix_dp_enable_sink_psr(dp);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
/* Check whether panel supports fast training */
|
|
ret = analogix_dp_fast_link_train_detection(dp);
|
|
if (ret)
|
|
dp->psr_enable = false;
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* This function is a bit of a catch-all for panel preparation, hopefully
|
|
* simplifying the logic of functions that need to prepare/unprepare the panel
|
|
* below.
|
|
*
|
|
* If @prepare is true, this function will prepare the panel. Conversely, if it
|
|
* is false, the panel will be unprepared.
|
|
*
|
|
* If @is_modeset_prepare is true, the function will disregard the current state
|
|
* of the panel and either prepare/unprepare the panel based on @prepare. Once
|
|
* it finishes, it will update dp->panel_is_modeset to reflect the current state
|
|
* of the panel.
|
|
*/
|
|
static int analogix_dp_prepare_panel(struct analogix_dp_device *dp,
|
|
bool prepare, bool is_modeset_prepare)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (!dp->plat_data->panel)
|
|
return 0;
|
|
|
|
mutex_lock(&dp->panel_lock);
|
|
|
|
/*
|
|
* Exit early if this is a temporary prepare/unprepare and we're already
|
|
* modeset (since we neither want to prepare twice or unprepare early).
|
|
*/
|
|
if (dp->panel_is_modeset && !is_modeset_prepare)
|
|
goto out;
|
|
|
|
if (prepare)
|
|
ret = drm_panel_prepare(dp->plat_data->panel);
|
|
else
|
|
ret = drm_panel_unprepare(dp->plat_data->panel);
|
|
|
|
if (ret)
|
|
goto out;
|
|
|
|
if (is_modeset_prepare)
|
|
dp->panel_is_modeset = prepare;
|
|
|
|
out:
|
|
mutex_unlock(&dp->panel_lock);
|
|
return ret;
|
|
}
|
|
|
|
static int analogix_dp_get_modes(struct drm_connector *connector)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(connector);
|
|
struct edid *edid;
|
|
int ret, num_modes = 0;
|
|
|
|
if (dp->plat_data->panel) {
|
|
num_modes += drm_panel_get_modes(dp->plat_data->panel);
|
|
} else {
|
|
ret = analogix_dp_prepare_panel(dp, true, false);
|
|
if (ret) {
|
|
DRM_ERROR("Failed to prepare panel (%d)\n", ret);
|
|
return 0;
|
|
}
|
|
|
|
pm_runtime_get_sync(dp->dev);
|
|
edid = drm_get_edid(connector, &dp->aux.ddc);
|
|
pm_runtime_put(dp->dev);
|
|
if (edid) {
|
|
drm_mode_connector_update_edid_property(&dp->connector,
|
|
edid);
|
|
num_modes += drm_add_edid_modes(&dp->connector, edid);
|
|
kfree(edid);
|
|
}
|
|
|
|
ret = analogix_dp_prepare_panel(dp, false, false);
|
|
if (ret)
|
|
DRM_ERROR("Failed to unprepare panel (%d)\n", ret);
|
|
}
|
|
|
|
if (dp->plat_data->get_modes)
|
|
num_modes += dp->plat_data->get_modes(dp->plat_data, connector);
|
|
|
|
return num_modes;
|
|
}
|
|
|
|
static struct drm_encoder *
|
|
analogix_dp_best_encoder(struct drm_connector *connector)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(connector);
|
|
|
|
return dp->encoder;
|
|
}
|
|
|
|
static const struct drm_connector_helper_funcs analogix_dp_connector_helper_funcs = {
|
|
.get_modes = analogix_dp_get_modes,
|
|
.best_encoder = analogix_dp_best_encoder,
|
|
};
|
|
|
|
static enum drm_connector_status
|
|
analogix_dp_detect(struct drm_connector *connector, bool force)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(connector);
|
|
enum drm_connector_status status = connector_status_disconnected;
|
|
int ret;
|
|
|
|
if (dp->plat_data->panel)
|
|
return connector_status_connected;
|
|
|
|
ret = analogix_dp_prepare_panel(dp, true, false);
|
|
if (ret) {
|
|
DRM_ERROR("Failed to prepare panel (%d)\n", ret);
|
|
return connector_status_disconnected;
|
|
}
|
|
|
|
if (!analogix_dp_detect_hpd(dp))
|
|
status = connector_status_connected;
|
|
|
|
ret = analogix_dp_prepare_panel(dp, false, false);
|
|
if (ret)
|
|
DRM_ERROR("Failed to unprepare panel (%d)\n", ret);
|
|
|
|
return status;
|
|
}
|
|
|
|
static const struct drm_connector_funcs analogix_dp_connector_funcs = {
|
|
.fill_modes = drm_helper_probe_single_connector_modes,
|
|
.detect = analogix_dp_detect,
|
|
.destroy = drm_connector_cleanup,
|
|
.reset = drm_atomic_helper_connector_reset,
|
|
.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
|
|
.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
|
|
};
|
|
|
|
static int analogix_dp_bridge_attach(struct drm_bridge *bridge)
|
|
{
|
|
struct analogix_dp_device *dp = bridge->driver_private;
|
|
struct drm_encoder *encoder = dp->encoder;
|
|
struct drm_connector *connector = NULL;
|
|
int ret = 0;
|
|
|
|
if (!bridge->encoder) {
|
|
DRM_ERROR("Parent encoder object not found");
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (!dp->plat_data->skip_connector) {
|
|
connector = &dp->connector;
|
|
connector->polled = DRM_CONNECTOR_POLL_HPD;
|
|
|
|
ret = drm_connector_init(dp->drm_dev, connector,
|
|
&analogix_dp_connector_funcs,
|
|
DRM_MODE_CONNECTOR_eDP);
|
|
if (ret) {
|
|
DRM_ERROR("Failed to initialize connector with drm\n");
|
|
return ret;
|
|
}
|
|
|
|
drm_connector_helper_add(connector,
|
|
&analogix_dp_connector_helper_funcs);
|
|
drm_mode_connector_attach_encoder(connector, encoder);
|
|
}
|
|
|
|
/*
|
|
* NOTE: the connector registration is implemented in analogix
|
|
* platform driver, that to say connector would be exist after
|
|
* plat_data->attch return, that's why we record the connector
|
|
* point after plat attached.
|
|
*/
|
|
if (dp->plat_data->attach) {
|
|
ret = dp->plat_data->attach(dp->plat_data, bridge, connector);
|
|
if (ret) {
|
|
DRM_ERROR("Failed at platform attch func\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
if (dp->plat_data->panel) {
|
|
ret = drm_panel_attach(dp->plat_data->panel, &dp->connector);
|
|
if (ret) {
|
|
DRM_ERROR("Failed to attach panel\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void analogix_dp_bridge_pre_enable(struct drm_bridge *bridge)
|
|
{
|
|
struct analogix_dp_device *dp = bridge->driver_private;
|
|
int ret;
|
|
|
|
ret = analogix_dp_prepare_panel(dp, true, true);
|
|
if (ret)
|
|
DRM_ERROR("failed to setup the panel ret = %d\n", ret);
|
|
}
|
|
|
|
static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
|
|
pm_runtime_get_sync(dp->dev);
|
|
|
|
ret = clk_prepare_enable(dp->clock);
|
|
if (ret < 0) {
|
|
DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret);
|
|
goto out_dp_clk_pre;
|
|
}
|
|
|
|
if (dp->plat_data->power_on_start)
|
|
dp->plat_data->power_on_start(dp->plat_data);
|
|
|
|
phy_power_on(dp->phy);
|
|
|
|
ret = analogix_dp_init_dp(dp);
|
|
if (ret)
|
|
goto out_dp_init;
|
|
|
|
/*
|
|
* According to DP spec v1.3 chap 3.5.1.2 Link Training,
|
|
* We should first make sure the HPD signal is asserted high by device
|
|
* when we want to establish a link with it.
|
|
*/
|
|
ret = analogix_dp_detect_hpd(dp);
|
|
if (ret) {
|
|
DRM_ERROR("failed to get hpd single ret = %d\n", ret);
|
|
goto out_dp_init;
|
|
}
|
|
|
|
ret = analogix_dp_commit(dp);
|
|
if (ret) {
|
|
DRM_ERROR("dp commit error, ret = %d\n", ret);
|
|
goto out_dp_init;
|
|
}
|
|
|
|
if (dp->plat_data->power_on_end)
|
|
dp->plat_data->power_on_end(dp->plat_data);
|
|
|
|
enable_irq(dp->irq);
|
|
return 0;
|
|
|
|
out_dp_init:
|
|
phy_power_off(dp->phy);
|
|
if (dp->plat_data->power_off)
|
|
dp->plat_data->power_off(dp->plat_data);
|
|
clk_disable_unprepare(dp->clock);
|
|
out_dp_clk_pre:
|
|
pm_runtime_put_sync(dp->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void analogix_dp_bridge_enable(struct drm_bridge *bridge)
|
|
{
|
|
struct analogix_dp_device *dp = bridge->driver_private;
|
|
int timeout_loop = 0;
|
|
|
|
if (dp->dpms_mode == DRM_MODE_DPMS_ON)
|
|
return;
|
|
|
|
while (timeout_loop < MAX_PLL_LOCK_LOOP) {
|
|
if (analogix_dp_set_bridge(dp) == 0) {
|
|
dp->dpms_mode = DRM_MODE_DPMS_ON;
|
|
return;
|
|
}
|
|
dev_err(dp->dev, "failed to set bridge, retry: %d\n",
|
|
timeout_loop);
|
|
timeout_loop++;
|
|
usleep_range(10, 11);
|
|
}
|
|
dev_err(dp->dev, "too many times retry set bridge, give it up\n");
|
|
}
|
|
|
|
static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
|
|
{
|
|
struct analogix_dp_device *dp = bridge->driver_private;
|
|
int ret;
|
|
|
|
if (dp->dpms_mode != DRM_MODE_DPMS_ON)
|
|
return;
|
|
|
|
if (dp->plat_data->panel) {
|
|
if (drm_panel_disable(dp->plat_data->panel)) {
|
|
DRM_ERROR("failed to disable the panel\n");
|
|
return;
|
|
}
|
|
}
|
|
|
|
disable_irq(dp->irq);
|
|
|
|
if (dp->plat_data->power_off)
|
|
dp->plat_data->power_off(dp->plat_data);
|
|
|
|
analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);
|
|
phy_power_off(dp->phy);
|
|
|
|
clk_disable_unprepare(dp->clock);
|
|
|
|
pm_runtime_put_sync(dp->dev);
|
|
|
|
ret = analogix_dp_prepare_panel(dp, false, true);
|
|
if (ret)
|
|
DRM_ERROR("failed to setup the panel ret = %d\n", ret);
|
|
|
|
dp->psr_enable = false;
|
|
dp->fast_train_enable = false;
|
|
dp->dpms_mode = DRM_MODE_DPMS_OFF;
|
|
}
|
|
|
|
static void analogix_dp_bridge_mode_set(struct drm_bridge *bridge,
|
|
struct drm_display_mode *orig_mode,
|
|
struct drm_display_mode *mode)
|
|
{
|
|
struct analogix_dp_device *dp = bridge->driver_private;
|
|
struct drm_display_info *display_info = &dp->connector.display_info;
|
|
struct video_info *video = &dp->video_info;
|
|
struct device_node *dp_node = dp->dev->of_node;
|
|
int vic;
|
|
|
|
/* Input video interlaces & hsync pol & vsync pol */
|
|
video->interlaced = !!(mode->flags & DRM_MODE_FLAG_INTERLACE);
|
|
video->v_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NVSYNC);
|
|
video->h_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NHSYNC);
|
|
|
|
/* Input video dynamic_range & colorimetry */
|
|
vic = drm_match_cea_mode(mode);
|
|
if ((vic == 6) || (vic == 7) || (vic == 21) || (vic == 22) ||
|
|
(vic == 2) || (vic == 3) || (vic == 17) || (vic == 18)) {
|
|
video->dynamic_range = CEA;
|
|
video->ycbcr_coeff = COLOR_YCBCR601;
|
|
} else if (vic) {
|
|
video->dynamic_range = CEA;
|
|
video->ycbcr_coeff = COLOR_YCBCR709;
|
|
} else {
|
|
video->dynamic_range = VESA;
|
|
video->ycbcr_coeff = COLOR_YCBCR709;
|
|
}
|
|
|
|
/* Input vide bpc and color_formats */
|
|
switch (display_info->bpc) {
|
|
case 12:
|
|
video->color_depth = COLOR_12;
|
|
break;
|
|
case 10:
|
|
video->color_depth = COLOR_10;
|
|
break;
|
|
case 8:
|
|
video->color_depth = COLOR_8;
|
|
break;
|
|
case 6:
|
|
video->color_depth = COLOR_6;
|
|
break;
|
|
default:
|
|
video->color_depth = COLOR_8;
|
|
break;
|
|
}
|
|
if (display_info->color_formats & DRM_COLOR_FORMAT_YCRCB444)
|
|
video->color_space = COLOR_YCBCR444;
|
|
else if (display_info->color_formats & DRM_COLOR_FORMAT_YCRCB422)
|
|
video->color_space = COLOR_YCBCR422;
|
|
else if (display_info->color_formats & DRM_COLOR_FORMAT_RGB444)
|
|
video->color_space = COLOR_RGB;
|
|
else
|
|
video->color_space = COLOR_RGB;
|
|
|
|
/*
|
|
* NOTE: those property parsing code is used for providing backward
|
|
* compatibility for samsung platform.
|
|
* Due to we used the "of_property_read_u32" interfaces, when this
|
|
* property isn't present, the "video_info" can keep the original
|
|
* values and wouldn't be modified.
|
|
*/
|
|
of_property_read_u32(dp_node, "samsung,color-space",
|
|
&video->color_space);
|
|
of_property_read_u32(dp_node, "samsung,dynamic-range",
|
|
&video->dynamic_range);
|
|
of_property_read_u32(dp_node, "samsung,ycbcr-coeff",
|
|
&video->ycbcr_coeff);
|
|
of_property_read_u32(dp_node, "samsung,color-depth",
|
|
&video->color_depth);
|
|
if (of_property_read_bool(dp_node, "hsync-active-high"))
|
|
video->h_sync_polarity = true;
|
|
if (of_property_read_bool(dp_node, "vsync-active-high"))
|
|
video->v_sync_polarity = true;
|
|
if (of_property_read_bool(dp_node, "interlaced"))
|
|
video->interlaced = true;
|
|
}
|
|
|
|
static void analogix_dp_bridge_nop(struct drm_bridge *bridge)
|
|
{
|
|
/* do nothing */
|
|
}
|
|
|
|
static const struct drm_bridge_funcs analogix_dp_bridge_funcs = {
|
|
.pre_enable = analogix_dp_bridge_pre_enable,
|
|
.enable = analogix_dp_bridge_enable,
|
|
.disable = analogix_dp_bridge_disable,
|
|
.post_disable = analogix_dp_bridge_nop,
|
|
.mode_set = analogix_dp_bridge_mode_set,
|
|
.attach = analogix_dp_bridge_attach,
|
|
};
|
|
|
|
static int analogix_dp_create_bridge(struct drm_device *drm_dev,
|
|
struct analogix_dp_device *dp)
|
|
{
|
|
struct drm_bridge *bridge;
|
|
int ret;
|
|
|
|
bridge = devm_kzalloc(drm_dev->dev, sizeof(*bridge), GFP_KERNEL);
|
|
if (!bridge) {
|
|
DRM_ERROR("failed to allocate for drm bridge\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
dp->bridge = bridge;
|
|
|
|
bridge->driver_private = dp;
|
|
bridge->funcs = &analogix_dp_bridge_funcs;
|
|
|
|
ret = drm_bridge_attach(dp->encoder, bridge, NULL);
|
|
if (ret) {
|
|
DRM_ERROR("failed to attach drm bridge\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int analogix_dp_dt_parse_pdata(struct analogix_dp_device *dp)
|
|
{
|
|
struct device_node *dp_node = dp->dev->of_node;
|
|
struct video_info *video_info = &dp->video_info;
|
|
|
|
switch (dp->plat_data->dev_type) {
|
|
case RK3288_DP:
|
|
case RK3399_EDP:
|
|
/*
|
|
* Like Rk3288 DisplayPort TRM indicate that "Main link
|
|
* containing 4 physical lanes of 2.7/1.62 Gbps/lane".
|
|
*/
|
|
video_info->max_link_rate = 0x0A;
|
|
video_info->max_lane_count = 0x04;
|
|
break;
|
|
case EXYNOS_DP:
|
|
/*
|
|
* NOTE: those property parseing code is used for
|
|
* providing backward compatibility for samsung platform.
|
|
*/
|
|
of_property_read_u32(dp_node, "samsung,link-rate",
|
|
&video_info->max_link_rate);
|
|
of_property_read_u32(dp_node, "samsung,lane-count",
|
|
&video_info->max_lane_count);
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static ssize_t analogix_dpaux_transfer(struct drm_dp_aux *aux,
|
|
struct drm_dp_aux_msg *msg)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(aux);
|
|
|
|
return analogix_dp_transfer(dp, msg);
|
|
}
|
|
|
|
struct analogix_dp_device *
|
|
analogix_dp_bind(struct device *dev, struct drm_device *drm_dev,
|
|
struct analogix_dp_plat_data *plat_data)
|
|
{
|
|
struct platform_device *pdev = to_platform_device(dev);
|
|
struct analogix_dp_device *dp;
|
|
struct resource *res;
|
|
unsigned int irq_flags;
|
|
int ret;
|
|
|
|
if (!plat_data) {
|
|
dev_err(dev, "Invalided input plat_data\n");
|
|
return ERR_PTR(-EINVAL);
|
|
}
|
|
|
|
dp = devm_kzalloc(dev, sizeof(struct analogix_dp_device), GFP_KERNEL);
|
|
if (!dp)
|
|
return ERR_PTR(-ENOMEM);
|
|
|
|
dp->dev = &pdev->dev;
|
|
dp->dpms_mode = DRM_MODE_DPMS_OFF;
|
|
|
|
mutex_init(&dp->panel_lock);
|
|
dp->panel_is_modeset = false;
|
|
|
|
/*
|
|
* platform dp driver need containor_of the plat_data to get
|
|
* the driver private data, so we need to store the point of
|
|
* plat_data, not the context of plat_data.
|
|
*/
|
|
dp->plat_data = plat_data;
|
|
|
|
ret = analogix_dp_dt_parse_pdata(dp);
|
|
if (ret)
|
|
return ERR_PTR(ret);
|
|
|
|
dp->phy = devm_phy_get(dp->dev, "dp");
|
|
if (IS_ERR(dp->phy)) {
|
|
dev_err(dp->dev, "no DP phy configured\n");
|
|
ret = PTR_ERR(dp->phy);
|
|
if (ret) {
|
|
/*
|
|
* phy itself is not enabled, so we can move forward
|
|
* assigning NULL to phy pointer.
|
|
*/
|
|
if (ret == -ENOSYS || ret == -ENODEV)
|
|
dp->phy = NULL;
|
|
else
|
|
return ERR_PTR(ret);
|
|
}
|
|
}
|
|
|
|
dp->clock = devm_clk_get(&pdev->dev, "dp");
|
|
if (IS_ERR(dp->clock)) {
|
|
dev_err(&pdev->dev, "failed to get clock\n");
|
|
return ERR_CAST(dp->clock);
|
|
}
|
|
|
|
clk_prepare_enable(dp->clock);
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
|
|
dp->reg_base = devm_ioremap_resource(&pdev->dev, res);
|
|
if (IS_ERR(dp->reg_base))
|
|
return ERR_CAST(dp->reg_base);
|
|
|
|
dp->force_hpd = of_property_read_bool(dev->of_node, "force-hpd");
|
|
|
|
dp->hpd_gpio = of_get_named_gpio(dev->of_node, "hpd-gpios", 0);
|
|
if (!gpio_is_valid(dp->hpd_gpio))
|
|
dp->hpd_gpio = of_get_named_gpio(dev->of_node,
|
|
"samsung,hpd-gpio", 0);
|
|
|
|
if (gpio_is_valid(dp->hpd_gpio)) {
|
|
/*
|
|
* Set up the hotplug GPIO from the device tree as an interrupt.
|
|
* Simply specifying a different interrupt in the device tree
|
|
* doesn't work since we handle hotplug rather differently when
|
|
* using a GPIO. We also need the actual GPIO specifier so
|
|
* that we can get the current state of the GPIO.
|
|
*/
|
|
ret = devm_gpio_request_one(&pdev->dev, dp->hpd_gpio, GPIOF_IN,
|
|
"hpd_gpio");
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to get hpd gpio\n");
|
|
return ERR_PTR(ret);
|
|
}
|
|
dp->irq = gpio_to_irq(dp->hpd_gpio);
|
|
irq_flags = IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING;
|
|
} else {
|
|
dp->hpd_gpio = -ENODEV;
|
|
dp->irq = platform_get_irq(pdev, 0);
|
|
irq_flags = 0;
|
|
}
|
|
|
|
if (dp->irq == -ENXIO) {
|
|
dev_err(&pdev->dev, "failed to get irq\n");
|
|
return ERR_PTR(-ENODEV);
|
|
}
|
|
|
|
ret = devm_request_threaded_irq(&pdev->dev, dp->irq,
|
|
analogix_dp_hardirq,
|
|
analogix_dp_irq_thread,
|
|
irq_flags, "analogix-dp", dp);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to request irq\n");
|
|
goto err_disable_pm_runtime;
|
|
}
|
|
disable_irq(dp->irq);
|
|
|
|
dp->drm_dev = drm_dev;
|
|
dp->encoder = dp->plat_data->encoder;
|
|
|
|
dp->aux.name = "DP-AUX";
|
|
dp->aux.transfer = analogix_dpaux_transfer;
|
|
dp->aux.dev = &pdev->dev;
|
|
|
|
ret = drm_dp_aux_register(&dp->aux);
|
|
if (ret)
|
|
return ERR_PTR(ret);
|
|
|
|
pm_runtime_enable(dev);
|
|
|
|
ret = analogix_dp_create_bridge(drm_dev, dp);
|
|
if (ret) {
|
|
DRM_ERROR("failed to create bridge (%d)\n", ret);
|
|
goto err_disable_pm_runtime;
|
|
}
|
|
|
|
return dp;
|
|
|
|
err_disable_pm_runtime:
|
|
|
|
pm_runtime_disable(dev);
|
|
|
|
return ERR_PTR(ret);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_bind);
|
|
|
|
void analogix_dp_unbind(struct analogix_dp_device *dp)
|
|
{
|
|
analogix_dp_bridge_disable(dp->bridge);
|
|
dp->connector.funcs->destroy(&dp->connector);
|
|
|
|
if (dp->plat_data->panel) {
|
|
if (drm_panel_unprepare(dp->plat_data->panel))
|
|
DRM_ERROR("failed to turnoff the panel\n");
|
|
if (drm_panel_detach(dp->plat_data->panel))
|
|
DRM_ERROR("failed to detach the panel\n");
|
|
}
|
|
|
|
drm_dp_aux_unregister(&dp->aux);
|
|
pm_runtime_disable(dp->dev);
|
|
clk_disable_unprepare(dp->clock);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_unbind);
|
|
|
|
#ifdef CONFIG_PM
|
|
int analogix_dp_suspend(struct analogix_dp_device *dp)
|
|
{
|
|
clk_disable_unprepare(dp->clock);
|
|
|
|
if (dp->plat_data->panel) {
|
|
if (drm_panel_unprepare(dp->plat_data->panel))
|
|
DRM_ERROR("failed to turnoff the panel\n");
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_suspend);
|
|
|
|
int analogix_dp_resume(struct analogix_dp_device *dp)
|
|
{
|
|
int ret;
|
|
|
|
ret = clk_prepare_enable(dp->clock);
|
|
if (ret < 0) {
|
|
DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
if (dp->plat_data->panel) {
|
|
if (drm_panel_prepare(dp->plat_data->panel)) {
|
|
DRM_ERROR("failed to setup the panel\n");
|
|
return -EBUSY;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_resume);
|
|
#endif
|
|
|
|
int analogix_dp_start_crc(struct drm_connector *connector)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(connector);
|
|
|
|
if (!connector->state->crtc) {
|
|
DRM_ERROR("Connector %s doesn't currently have a CRTC.\n",
|
|
connector->name);
|
|
return -EINVAL;
|
|
}
|
|
|
|
return drm_dp_start_crc(&dp->aux, connector->state->crtc);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_start_crc);
|
|
|
|
int analogix_dp_stop_crc(struct drm_connector *connector)
|
|
{
|
|
struct analogix_dp_device *dp = to_dp(connector);
|
|
|
|
return drm_dp_stop_crc(&dp->aux);
|
|
}
|
|
EXPORT_SYMBOL_GPL(analogix_dp_stop_crc);
|
|
|
|
MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>");
|
|
MODULE_DESCRIPTION("Analogix DP Core Driver");
|
|
MODULE_LICENSE("GPL v2");
|