![Tony Cho](/assets/img/avatar_default.png)
This patch removes the warnings reported by checkpatch.pl on the short description for the config symbol in the Kconfig by adding more comments to describe the config symbol in more detail. Signed-off-by: Tony Cho <tony.cho@atmel.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
72 lines
2.6 KiB
Plaintext
72 lines
2.6 KiB
Plaintext
config WILC1000
|
|
tristate "WILC1000 support (WiFi only)"
|
|
depends on BROKEN
|
|
depends on !S390
|
|
depends on CFG80211 && WEXT_CORE && INET
|
|
depends on MMC || SPI
|
|
---help---
|
|
This module only support IEEE 802.11n WiFi.
|
|
|
|
choice
|
|
prompt "Memory Allocation"
|
|
depends on WILC1000
|
|
default WILC1000_PREALLOCATE_AT_LOADING_DRIVER
|
|
|
|
config WILC1000_PREALLOCATE_AT_LOADING_DRIVER
|
|
bool "Preallocate memory at loading driver"
|
|
---help---
|
|
This choice supports static allocation of the memory
|
|
for the receive buffer. The driver will allocate the RX buffer
|
|
during initial time. The driver will also free the buffer
|
|
by calling network device stop.
|
|
|
|
config WILC1000_DYNAMICALLY_ALLOCATE_MEMROY
|
|
bool "Dynamically allocate memory in real time"
|
|
---help---
|
|
This choice supports dynamic allocation of the memory
|
|
for the receive buffer. The driver will allocate the RX buffer
|
|
when it is required.
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Bus Type"
|
|
depends on WILC1000
|
|
default WILC1000_SDIO
|
|
|
|
config WILC1000_SDIO
|
|
bool "SDIO support"
|
|
depends on MMC
|
|
---help---
|
|
This module adds support for the SDIO interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface.
|
|
It meets SDIO card specification version 2.0. The interface supports
|
|
the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz.
|
|
The host can use this interface to read and write from any register
|
|
within the chip as well as configure the WILC1000 for data DMA.
|
|
To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
|
this if your platform is using the SDIO bus.
|
|
|
|
config WILC1000_SPI
|
|
depends on SPI
|
|
bool "SPI support"
|
|
---help---
|
|
This module adds support for the SPI interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral
|
|
Interface (SPI) that operates as a SPI slave. This SPI interface can
|
|
be used for control and for serial I/O of 802.11 data. The SPI is a
|
|
full-duplex slave synchronous serial interface that is available
|
|
immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
|
|
VDDIO. Select this if your platform is using the SPI bus.
|
|
endchoice
|
|
|
|
config WILC1000_HW_OOB_INTR
|
|
bool "Use out of band interrupt"
|
|
depends on WILC1000 && WILC1000_SDIO
|
|
default n
|
|
---help---
|
|
This option enables out-of-band interrupt support for the WILC1000
|
|
chipset. This OOB interrupt is intended to provide a faster interrupt
|
|
mechanism for SDIO host controllers that don't support SDIO interrupt.
|
|
Select this option If the SDIO host controller in your platform
|
|
doesn't support SDIO time devision interrupt.
|