![Rishi Gupta](/assets/img/avatar_default.png)
MCP2221 is a USB HID to I2C/SMbus host bridge device. This commit implements i2c and smbus host adapter support. 7-bit address and i2c multi-message transaction is also supported. Signed-off-by: Rishi Gupta <gupt21@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
743 lines
17 KiB
C
743 lines
17 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* MCP2221A - Microchip USB to I2C Host Protocol Bridge
|
|
*
|
|
* Copyright (c) 2020, Rishi Gupta <gupt21@gmail.com>
|
|
*
|
|
* Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/err.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/completion.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/hid.h>
|
|
#include <linux/hidraw.h>
|
|
#include <linux/i2c.h>
|
|
#include "hid-ids.h"
|
|
|
|
/* Commands codes in a raw output report */
|
|
enum {
|
|
MCP2221_I2C_WR_DATA = 0x90,
|
|
MCP2221_I2C_WR_NO_STOP = 0x94,
|
|
MCP2221_I2C_RD_DATA = 0x91,
|
|
MCP2221_I2C_RD_RPT_START = 0x93,
|
|
MCP2221_I2C_GET_DATA = 0x40,
|
|
MCP2221_I2C_PARAM_OR_STATUS = 0x10,
|
|
MCP2221_I2C_SET_SPEED = 0x20,
|
|
MCP2221_I2C_CANCEL = 0x10,
|
|
};
|
|
|
|
/* Response codes in a raw input report */
|
|
enum {
|
|
MCP2221_SUCCESS = 0x00,
|
|
MCP2221_I2C_ENG_BUSY = 0x01,
|
|
MCP2221_I2C_START_TOUT = 0x12,
|
|
MCP2221_I2C_STOP_TOUT = 0x62,
|
|
MCP2221_I2C_WRADDRL_TOUT = 0x23,
|
|
MCP2221_I2C_WRDATA_TOUT = 0x44,
|
|
MCP2221_I2C_WRADDRL_NACK = 0x25,
|
|
MCP2221_I2C_MASK_ADDR_NACK = 0x40,
|
|
MCP2221_I2C_WRADDRL_SEND = 0x21,
|
|
MCP2221_I2C_ADDR_NACK = 0x25,
|
|
MCP2221_I2C_READ_COMPL = 0x55,
|
|
};
|
|
|
|
/*
|
|
* There is no way to distinguish responses. Therefore next command
|
|
* is sent only after response to previous has been received. Mutex
|
|
* lock is used for this purpose mainly.
|
|
*/
|
|
struct mcp2221 {
|
|
struct hid_device *hdev;
|
|
struct i2c_adapter adapter;
|
|
struct mutex lock;
|
|
struct completion wait_in_report;
|
|
u8 *rxbuf;
|
|
u8 txbuf[64];
|
|
int rxbuf_idx;
|
|
int status;
|
|
u8 cur_i2c_clk_div;
|
|
};
|
|
|
|
/*
|
|
* Default i2c bus clock frequency 400 kHz. Modify this if you
|
|
* want to set some other frequency (min 50 kHz - max 400 kHz).
|
|
*/
|
|
static uint i2c_clk_freq = 400;
|
|
|
|
/* Synchronously send output report to the device */
|
|
static int mcp_send_report(struct mcp2221 *mcp,
|
|
u8 *out_report, size_t len)
|
|
{
|
|
u8 *buf;
|
|
int ret;
|
|
|
|
buf = kmemdup(out_report, len, GFP_KERNEL);
|
|
if (!buf)
|
|
return -ENOMEM;
|
|
|
|
/* mcp2221 uses interrupt endpoint for out reports */
|
|
ret = hid_hw_output_report(mcp->hdev, buf, len);
|
|
kfree(buf);
|
|
|
|
if (ret < 0)
|
|
return ret;
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Send o/p report to the device and wait for i/p report to be
|
|
* received from the device. If the device does not respond,
|
|
* we timeout.
|
|
*/
|
|
static int mcp_send_data_req_status(struct mcp2221 *mcp,
|
|
u8 *out_report, int len)
|
|
{
|
|
int ret;
|
|
unsigned long t;
|
|
|
|
reinit_completion(&mcp->wait_in_report);
|
|
|
|
ret = mcp_send_report(mcp, out_report, len);
|
|
if (ret)
|
|
return ret;
|
|
|
|
t = wait_for_completion_timeout(&mcp->wait_in_report,
|
|
msecs_to_jiffies(4000));
|
|
if (!t)
|
|
return -ETIMEDOUT;
|
|
|
|
return mcp->status;
|
|
}
|
|
|
|
/* Check pass/fail for actual communication with i2c slave */
|
|
static int mcp_chk_last_cmd_status(struct mcp2221 *mcp)
|
|
{
|
|
memset(mcp->txbuf, 0, 8);
|
|
mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS;
|
|
|
|
return mcp_send_data_req_status(mcp, mcp->txbuf, 8);
|
|
}
|
|
|
|
/* Cancels last command releasing i2c bus just in case occupied */
|
|
static int mcp_cancel_last_cmd(struct mcp2221 *mcp)
|
|
{
|
|
memset(mcp->txbuf, 0, 8);
|
|
mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS;
|
|
mcp->txbuf[2] = MCP2221_I2C_CANCEL;
|
|
|
|
return mcp_send_data_req_status(mcp, mcp->txbuf, 8);
|
|
}
|
|
|
|
static int mcp_set_i2c_speed(struct mcp2221 *mcp)
|
|
{
|
|
int ret;
|
|
|
|
memset(mcp->txbuf, 0, 8);
|
|
mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS;
|
|
mcp->txbuf[3] = MCP2221_I2C_SET_SPEED;
|
|
mcp->txbuf[4] = mcp->cur_i2c_clk_div;
|
|
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, 8);
|
|
if (ret) {
|
|
/* Small delay is needed here */
|
|
usleep_range(980, 1000);
|
|
mcp_cancel_last_cmd(mcp);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* An output report can contain minimum 1 and maximum 60 user data
|
|
* bytes. If the number of data bytes is more then 60, we send it
|
|
* in chunks of 60 bytes. Last chunk may contain exactly 60 or less
|
|
* bytes. Total number of bytes is informed in very first report to
|
|
* mcp2221, from that point onwards it first collect all the data
|
|
* from host and then send to i2c slave device.
|
|
*/
|
|
static int mcp_i2c_write(struct mcp2221 *mcp,
|
|
struct i2c_msg *msg, int type, u8 last_status)
|
|
{
|
|
int ret, len, idx, sent;
|
|
|
|
idx = 0;
|
|
sent = 0;
|
|
if (msg->len < 60)
|
|
len = msg->len;
|
|
else
|
|
len = 60;
|
|
|
|
do {
|
|
mcp->txbuf[0] = type;
|
|
mcp->txbuf[1] = msg->len & 0xff;
|
|
mcp->txbuf[2] = msg->len >> 8;
|
|
mcp->txbuf[3] = (u8)(msg->addr << 1);
|
|
|
|
memcpy(&mcp->txbuf[4], &msg->buf[idx], len);
|
|
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, len + 4);
|
|
if (ret)
|
|
return ret;
|
|
|
|
usleep_range(980, 1000);
|
|
|
|
if (last_status) {
|
|
ret = mcp_chk_last_cmd_status(mcp);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
sent = sent + len;
|
|
if (sent >= msg->len)
|
|
break;
|
|
|
|
idx = idx + len;
|
|
if ((msg->len - sent) < 60)
|
|
len = msg->len - sent;
|
|
else
|
|
len = 60;
|
|
|
|
/*
|
|
* Testing shows delay is needed between successive writes
|
|
* otherwise next write fails on first-try from i2c core.
|
|
* This value is obtained through automated stress testing.
|
|
*/
|
|
usleep_range(980, 1000);
|
|
} while (len > 0);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Device reads all data (0 - 65535 bytes) from i2c slave device and
|
|
* stores it in device itself. This data is read back from device to
|
|
* host in multiples of 60 bytes using input reports.
|
|
*/
|
|
static int mcp_i2c_smbus_read(struct mcp2221 *mcp,
|
|
struct i2c_msg *msg, int type, u16 smbus_addr,
|
|
u8 smbus_len, u8 *smbus_buf)
|
|
{
|
|
int ret;
|
|
u16 total_len;
|
|
|
|
mcp->txbuf[0] = type;
|
|
if (msg) {
|
|
mcp->txbuf[1] = msg->len & 0xff;
|
|
mcp->txbuf[2] = msg->len >> 8;
|
|
mcp->txbuf[3] = (u8)(msg->addr << 1);
|
|
total_len = msg->len;
|
|
mcp->rxbuf = msg->buf;
|
|
} else {
|
|
mcp->txbuf[1] = smbus_len;
|
|
mcp->txbuf[2] = 0;
|
|
mcp->txbuf[3] = (u8)(smbus_addr << 1);
|
|
total_len = smbus_len;
|
|
mcp->rxbuf = smbus_buf;
|
|
}
|
|
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, 4);
|
|
if (ret)
|
|
return ret;
|
|
|
|
mcp->rxbuf_idx = 0;
|
|
|
|
do {
|
|
memset(mcp->txbuf, 0, 4);
|
|
mcp->txbuf[0] = MCP2221_I2C_GET_DATA;
|
|
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = mcp_chk_last_cmd_status(mcp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
usleep_range(980, 1000);
|
|
} while (mcp->rxbuf_idx < total_len);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mcp_i2c_xfer(struct i2c_adapter *adapter,
|
|
struct i2c_msg msgs[], int num)
|
|
{
|
|
int ret;
|
|
struct mcp2221 *mcp = i2c_get_adapdata(adapter);
|
|
|
|
hid_hw_power(mcp->hdev, PM_HINT_FULLON);
|
|
|
|
mutex_lock(&mcp->lock);
|
|
|
|
/* Setting speed before every transaction is required for mcp2221 */
|
|
ret = mcp_set_i2c_speed(mcp);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
if (num == 1) {
|
|
if (msgs->flags & I2C_M_RD) {
|
|
ret = mcp_i2c_smbus_read(mcp, msgs, MCP2221_I2C_RD_DATA,
|
|
0, 0, NULL);
|
|
} else {
|
|
ret = mcp_i2c_write(mcp, msgs, MCP2221_I2C_WR_DATA, 1);
|
|
}
|
|
if (ret)
|
|
goto exit;
|
|
ret = num;
|
|
} else if (num == 2) {
|
|
/* Ex transaction; send reg address and read its contents */
|
|
if (msgs[0].addr == msgs[1].addr &&
|
|
!(msgs[0].flags & I2C_M_RD) &&
|
|
(msgs[1].flags & I2C_M_RD)) {
|
|
|
|
ret = mcp_i2c_write(mcp, &msgs[0],
|
|
MCP2221_I2C_WR_NO_STOP, 0);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = mcp_i2c_smbus_read(mcp, &msgs[1],
|
|
MCP2221_I2C_RD_RPT_START,
|
|
0, 0, NULL);
|
|
if (ret)
|
|
goto exit;
|
|
ret = num;
|
|
} else {
|
|
dev_err(&adapter->dev,
|
|
"unsupported multi-msg i2c transaction\n");
|
|
ret = -EOPNOTSUPP;
|
|
}
|
|
} else {
|
|
dev_err(&adapter->dev,
|
|
"unsupported multi-msg i2c transaction\n");
|
|
ret = -EOPNOTSUPP;
|
|
}
|
|
|
|
exit:
|
|
hid_hw_power(mcp->hdev, PM_HINT_NORMAL);
|
|
mutex_unlock(&mcp->lock);
|
|
return ret;
|
|
}
|
|
|
|
static int mcp_smbus_write(struct mcp2221 *mcp, u16 addr,
|
|
u8 command, u8 *buf, u8 len, int type,
|
|
u8 last_status)
|
|
{
|
|
int data_len, ret;
|
|
|
|
mcp->txbuf[0] = type;
|
|
mcp->txbuf[1] = len + 1; /* 1 is due to command byte itself */
|
|
mcp->txbuf[2] = 0;
|
|
mcp->txbuf[3] = (u8)(addr << 1);
|
|
mcp->txbuf[4] = command;
|
|
|
|
switch (len) {
|
|
case 0:
|
|
data_len = 5;
|
|
break;
|
|
case 1:
|
|
mcp->txbuf[5] = buf[0];
|
|
data_len = 6;
|
|
break;
|
|
case 2:
|
|
mcp->txbuf[5] = buf[0];
|
|
mcp->txbuf[6] = buf[1];
|
|
data_len = 7;
|
|
break;
|
|
default:
|
|
memcpy(&mcp->txbuf[5], buf, len);
|
|
data_len = len + 5;
|
|
}
|
|
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, data_len);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (last_status) {
|
|
usleep_range(980, 1000);
|
|
|
|
ret = mcp_chk_last_cmd_status(mcp);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int mcp_smbus_xfer(struct i2c_adapter *adapter, u16 addr,
|
|
unsigned short flags, char read_write,
|
|
u8 command, int size,
|
|
union i2c_smbus_data *data)
|
|
{
|
|
int ret;
|
|
struct mcp2221 *mcp = i2c_get_adapdata(adapter);
|
|
|
|
hid_hw_power(mcp->hdev, PM_HINT_FULLON);
|
|
|
|
mutex_lock(&mcp->lock);
|
|
|
|
ret = mcp_set_i2c_speed(mcp);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
switch (size) {
|
|
|
|
case I2C_SMBUS_QUICK:
|
|
if (read_write == I2C_SMBUS_READ)
|
|
ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA,
|
|
addr, 0, &data->byte);
|
|
else
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_DATA, 1);
|
|
break;
|
|
case I2C_SMBUS_BYTE:
|
|
if (read_write == I2C_SMBUS_READ)
|
|
ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA,
|
|
addr, 1, &data->byte);
|
|
else
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_DATA, 1);
|
|
break;
|
|
case I2C_SMBUS_BYTE_DATA:
|
|
if (read_write == I2C_SMBUS_READ) {
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_NO_STOP, 0);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = mcp_i2c_smbus_read(mcp, NULL,
|
|
MCP2221_I2C_RD_RPT_START,
|
|
addr, 1, &data->byte);
|
|
} else {
|
|
ret = mcp_smbus_write(mcp, addr, command, &data->byte,
|
|
1, MCP2221_I2C_WR_DATA, 1);
|
|
}
|
|
break;
|
|
case I2C_SMBUS_WORD_DATA:
|
|
if (read_write == I2C_SMBUS_READ) {
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_NO_STOP, 0);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = mcp_i2c_smbus_read(mcp, NULL,
|
|
MCP2221_I2C_RD_RPT_START,
|
|
addr, 2, (u8 *)&data->word);
|
|
} else {
|
|
ret = mcp_smbus_write(mcp, addr, command,
|
|
(u8 *)&data->word, 2,
|
|
MCP2221_I2C_WR_DATA, 1);
|
|
}
|
|
break;
|
|
case I2C_SMBUS_BLOCK_DATA:
|
|
if (read_write == I2C_SMBUS_READ) {
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_NO_STOP, 1);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
mcp->rxbuf_idx = 0;
|
|
mcp->rxbuf = data->block;
|
|
mcp->txbuf[0] = MCP2221_I2C_GET_DATA;
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
|
|
if (ret)
|
|
goto exit;
|
|
} else {
|
|
if (!data->block[0]) {
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
ret = mcp_smbus_write(mcp, addr, command, data->block,
|
|
data->block[0] + 1,
|
|
MCP2221_I2C_WR_DATA, 1);
|
|
}
|
|
break;
|
|
case I2C_SMBUS_I2C_BLOCK_DATA:
|
|
if (read_write == I2C_SMBUS_READ) {
|
|
ret = mcp_smbus_write(mcp, addr, command, NULL,
|
|
0, MCP2221_I2C_WR_NO_STOP, 1);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
mcp->rxbuf_idx = 0;
|
|
mcp->rxbuf = data->block;
|
|
mcp->txbuf[0] = MCP2221_I2C_GET_DATA;
|
|
ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
|
|
if (ret)
|
|
goto exit;
|
|
} else {
|
|
if (!data->block[0]) {
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
ret = mcp_smbus_write(mcp, addr, command,
|
|
&data->block[1], data->block[0],
|
|
MCP2221_I2C_WR_DATA, 1);
|
|
}
|
|
break;
|
|
case I2C_SMBUS_PROC_CALL:
|
|
ret = mcp_smbus_write(mcp, addr, command,
|
|
(u8 *)&data->word,
|
|
2, MCP2221_I2C_WR_NO_STOP, 0);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = mcp_i2c_smbus_read(mcp, NULL,
|
|
MCP2221_I2C_RD_RPT_START,
|
|
addr, 2, (u8 *)&data->word);
|
|
break;
|
|
case I2C_SMBUS_BLOCK_PROC_CALL:
|
|
ret = mcp_smbus_write(mcp, addr, command, data->block,
|
|
data->block[0] + 1,
|
|
MCP2221_I2C_WR_NO_STOP, 0);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = mcp_i2c_smbus_read(mcp, NULL,
|
|
MCP2221_I2C_RD_RPT_START,
|
|
addr, I2C_SMBUS_BLOCK_MAX,
|
|
data->block);
|
|
break;
|
|
default:
|
|
dev_err(&mcp->adapter.dev,
|
|
"unsupported smbus transaction size:%d\n", size);
|
|
ret = -EOPNOTSUPP;
|
|
}
|
|
|
|
exit:
|
|
hid_hw_power(mcp->hdev, PM_HINT_NORMAL);
|
|
mutex_unlock(&mcp->lock);
|
|
return ret;
|
|
}
|
|
|
|
static u32 mcp_i2c_func(struct i2c_adapter *adapter)
|
|
{
|
|
return I2C_FUNC_I2C |
|
|
I2C_FUNC_SMBUS_READ_BLOCK_DATA |
|
|
I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
|
|
(I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_PEC);
|
|
}
|
|
|
|
static const struct i2c_algorithm mcp_i2c_algo = {
|
|
.master_xfer = mcp_i2c_xfer,
|
|
.smbus_xfer = mcp_smbus_xfer,
|
|
.functionality = mcp_i2c_func,
|
|
};
|
|
|
|
/* Gives current state of i2c engine inside mcp2221 */
|
|
static int mcp_get_i2c_eng_state(struct mcp2221 *mcp,
|
|
u8 *data, u8 idx)
|
|
{
|
|
int ret;
|
|
|
|
switch (data[idx]) {
|
|
case MCP2221_I2C_WRADDRL_NACK:
|
|
case MCP2221_I2C_WRADDRL_SEND:
|
|
ret = -ENXIO;
|
|
break;
|
|
case MCP2221_I2C_START_TOUT:
|
|
case MCP2221_I2C_STOP_TOUT:
|
|
case MCP2221_I2C_WRADDRL_TOUT:
|
|
case MCP2221_I2C_WRDATA_TOUT:
|
|
ret = -ETIMEDOUT;
|
|
break;
|
|
case MCP2221_I2C_ENG_BUSY:
|
|
ret = -EAGAIN;
|
|
break;
|
|
case MCP2221_SUCCESS:
|
|
ret = 0x00;
|
|
break;
|
|
default:
|
|
ret = -EIO;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* MCP2221 uses interrupt endpoint for input reports. This function
|
|
* is called by HID layer when it receives i/p report from mcp2221,
|
|
* which is actually a response to the previously sent command.
|
|
*
|
|
* MCP2221A firmware specific return codes are parsed and 0 or
|
|
* appropriate negative error code is returned. Delayed response
|
|
* results in timeout error and stray reponses results in -EIO.
|
|
*/
|
|
static int mcp2221_raw_event(struct hid_device *hdev,
|
|
struct hid_report *report, u8 *data, int size)
|
|
{
|
|
u8 *buf;
|
|
struct mcp2221 *mcp = hid_get_drvdata(hdev);
|
|
|
|
switch (data[0]) {
|
|
|
|
case MCP2221_I2C_WR_DATA:
|
|
case MCP2221_I2C_WR_NO_STOP:
|
|
case MCP2221_I2C_RD_DATA:
|
|
case MCP2221_I2C_RD_RPT_START:
|
|
switch (data[1]) {
|
|
case MCP2221_SUCCESS:
|
|
mcp->status = 0;
|
|
break;
|
|
default:
|
|
mcp->status = mcp_get_i2c_eng_state(mcp, data, 2);
|
|
}
|
|
complete(&mcp->wait_in_report);
|
|
break;
|
|
|
|
case MCP2221_I2C_PARAM_OR_STATUS:
|
|
switch (data[1]) {
|
|
case MCP2221_SUCCESS:
|
|
if ((mcp->txbuf[3] == MCP2221_I2C_SET_SPEED) &&
|
|
(data[3] != MCP2221_I2C_SET_SPEED)) {
|
|
mcp->status = -EAGAIN;
|
|
break;
|
|
}
|
|
if (data[20] & MCP2221_I2C_MASK_ADDR_NACK) {
|
|
mcp->status = -ENXIO;
|
|
break;
|
|
}
|
|
mcp->status = mcp_get_i2c_eng_state(mcp, data, 8);
|
|
break;
|
|
default:
|
|
mcp->status = -EIO;
|
|
}
|
|
complete(&mcp->wait_in_report);
|
|
break;
|
|
|
|
case MCP2221_I2C_GET_DATA:
|
|
switch (data[1]) {
|
|
case MCP2221_SUCCESS:
|
|
if (data[2] == MCP2221_I2C_ADDR_NACK) {
|
|
mcp->status = -ENXIO;
|
|
break;
|
|
}
|
|
if (!mcp_get_i2c_eng_state(mcp, data, 2)
|
|
&& (data[3] == 0)) {
|
|
mcp->status = 0;
|
|
break;
|
|
}
|
|
if (data[3] == 127) {
|
|
mcp->status = -EIO;
|
|
break;
|
|
}
|
|
if (data[2] == MCP2221_I2C_READ_COMPL) {
|
|
buf = mcp->rxbuf;
|
|
memcpy(&buf[mcp->rxbuf_idx], &data[4], data[3]);
|
|
mcp->rxbuf_idx = mcp->rxbuf_idx + data[3];
|
|
mcp->status = 0;
|
|
break;
|
|
}
|
|
mcp->status = -EIO;
|
|
break;
|
|
default:
|
|
mcp->status = -EIO;
|
|
}
|
|
complete(&mcp->wait_in_report);
|
|
break;
|
|
|
|
default:
|
|
mcp->status = -EIO;
|
|
complete(&mcp->wait_in_report);
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
static int mcp2221_probe(struct hid_device *hdev,
|
|
const struct hid_device_id *id)
|
|
{
|
|
int ret;
|
|
struct mcp2221 *mcp;
|
|
|
|
mcp = devm_kzalloc(&hdev->dev, sizeof(*mcp), GFP_KERNEL);
|
|
if (!mcp)
|
|
return -ENOMEM;
|
|
|
|
ret = hid_parse(hdev);
|
|
if (ret) {
|
|
hid_err(hdev, "can't parse reports\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
|
|
if (ret) {
|
|
hid_err(hdev, "can't start hardware\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = hid_hw_open(hdev);
|
|
if (ret) {
|
|
hid_err(hdev, "can't open device\n");
|
|
goto err_hstop;
|
|
}
|
|
|
|
mutex_init(&mcp->lock);
|
|
init_completion(&mcp->wait_in_report);
|
|
hid_set_drvdata(hdev, mcp);
|
|
mcp->hdev = hdev;
|
|
|
|
/* Set I2C bus clock diviser */
|
|
if (i2c_clk_freq > 400)
|
|
i2c_clk_freq = 400;
|
|
if (i2c_clk_freq < 50)
|
|
i2c_clk_freq = 50;
|
|
mcp->cur_i2c_clk_div = (12000000 / (i2c_clk_freq * 1000)) - 3;
|
|
|
|
mcp->adapter.owner = THIS_MODULE;
|
|
mcp->adapter.class = I2C_CLASS_HWMON;
|
|
mcp->adapter.algo = &mcp_i2c_algo;
|
|
mcp->adapter.retries = 1;
|
|
mcp->adapter.dev.parent = &hdev->dev;
|
|
snprintf(mcp->adapter.name, sizeof(mcp->adapter.name),
|
|
"MCP2221 usb-i2c bridge on hidraw%d",
|
|
((struct hidraw *)hdev->hidraw)->minor);
|
|
|
|
ret = i2c_add_adapter(&mcp->adapter);
|
|
if (ret) {
|
|
hid_err(hdev, "can't add usb-i2c adapter: %d\n", ret);
|
|
goto err_i2c;
|
|
}
|
|
i2c_set_adapdata(&mcp->adapter, mcp);
|
|
|
|
return 0;
|
|
|
|
err_i2c:
|
|
hid_hw_close(mcp->hdev);
|
|
err_hstop:
|
|
hid_hw_stop(mcp->hdev);
|
|
return ret;
|
|
}
|
|
|
|
static void mcp2221_remove(struct hid_device *hdev)
|
|
{
|
|
struct mcp2221 *mcp = hid_get_drvdata(hdev);
|
|
|
|
i2c_del_adapter(&mcp->adapter);
|
|
hid_hw_close(mcp->hdev);
|
|
hid_hw_stop(mcp->hdev);
|
|
}
|
|
|
|
static const struct hid_device_id mcp2221_devices[] = {
|
|
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(hid, mcp2221_devices);
|
|
|
|
static struct hid_driver mcp2221_driver = {
|
|
.name = "mcp2221",
|
|
.id_table = mcp2221_devices,
|
|
.probe = mcp2221_probe,
|
|
.remove = mcp2221_remove,
|
|
.raw_event = mcp2221_raw_event,
|
|
};
|
|
|
|
/* Register with HID core */
|
|
module_hid_driver(mcp2221_driver);
|
|
|
|
MODULE_AUTHOR("Rishi Gupta <gupt21@gmail.com>");
|
|
MODULE_DESCRIPTION("MCP2221 Microchip HID USB to I2C master bridge");
|
|
MODULE_LICENSE("GPL v2");
|