redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/drivers/staging/wilc1000/wilc_wlan_if.h
Aditya Shankar 46949b4856 staging: wilc1000: New cfg packet format in handle_set_wfi_drv_handler 
Change the config packet format used in handle_set_wfi_drv_handler()
to align the host driver with the new format used in the wilc firmware.

The change updates the format in which the host driver provides the
firmware with the drv_handler index and also uses two new
fields viz. "mode" and 'name" in the config packet along with this index
to directly provide details about the interface and its mode to the
firmware instead of having multiple if-else statements in the host driver
to decide which interface to configure.

This change requires users to move to the newer version of the wilc
firmware(14.02 or higher) available on the vendor tree on github or on the
linux-firmware project. The existing firmware files on the linux-firmware
project are very old and best not used.

Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-13 12:06:57 +02:00

898 lines
25 KiB
C
Raw Blame History

/* ///////////////////////////////////////////////////////////////////////// */
/* */
/* Copyright (c) Atmel Corporation. All rights reserved. */
/* */
/* Module Name: wilc_wlan_if.h */
/* */
/* */
/* ///////////////////////////////////////////////////////////////////////// */
#ifndef WILC_WLAN_IF_H
#define WILC_WLAN_IF_H
#include <linux/netdevice.h>
/********************************************
*
* Host Interface Defines
*
********************************************/
#define HIF_SDIO (0)
#define HIF_SPI BIT(0)
#define HIF_SDIO_GPIO_IRQ BIT(2)
/********************************************
*
* Wlan Interface Defines
*
********************************************/
struct sdio_cmd52 {
u32 read_write: 1;
u32 function: 3;
u32 raw: 1;
u32 address: 17;
u32 data: 8;
};
struct sdio_cmd53 {
u32 read_write: 1;
u32 function: 3;
u32 block_mode: 1;
u32 increment: 1;
u32 address: 17;
u32 count: 9;
u8 *buffer;
u32 block_size;
};
#define WILC_MAC_INDICATE_STATUS 0x1
#define WILC_MAC_STATUS_INIT -1
#define WILC_MAC_STATUS_READY 0
#define WILC_MAC_STATUS_CONNECT 1
#define WILC_MAC_INDICATE_SCAN 0x2
struct tx_complete_data {
int size;
void *buff;
u8 *bssid;
struct sk_buff *skb;
};
typedef void (*wilc_tx_complete_func_t)(void *, int);
#define WILC_TX_ERR_NO_BUF (-2)
/********************************************
*
* Wlan Configuration ID
*
********************************************/
#define WILC_MULTICAST_TABLE_SIZE 8
#define MAX_SSID_LEN 33
#define MAX_RATES_SUPPORTED 12
typedef enum {
SUPP_RATES_IE = 1,
EXT_SUPP_RATES_IE = 50,
HT_CAPABILITY_IE = 45,
RSN_IE = 48,
WPA_IE = 221,
WMM_IE = 221,
P2P_IE = 221,
} BEACON_IE;
typedef enum {
INFRASTRUCTURE = 0,
INDEPENDENT,
AP,
} BSSTYPE_T;
typedef enum {
RATE_AUTO = 0,
RATE_1MB = 1,
RATE_2MB = 2,
RATE_5MB = 5,
RATE_6MB = 6,
RATE_9MB = 9,
RATE_11MB = 11,
RATE_12MB = 12,
RATE_18MB = 18,
RATE_24MB = 24,
RATE_26MB = 36,
RATE_48MB = 48,
RATE_54MB = 54
} TX_RATE_T;
typedef enum {
B_ONLY_MODE = 0, /* 1, 2 M, otherwise 5, 11 M */
G_ONLY_MODE, /* 6,12,24 otherwise 9,18,36,48,54 */
G_MIXED_11B_1_MODE, /* 1,2,5.5,11 otherwise all on */
G_MIXED_11B_2_MODE, /* 1,2,5,11,6,12,24 otherwise all on */
} G_OPERATING_MODE_T;
typedef enum {
G_SHORT_PREAMBLE = 0, /* Short Preamble */
G_LONG_PREAMBLE = 1, /* Long Preamble */
G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */
} G_PREAMBLE_T;
#define MAC_CONNECTED 1
#define MAC_DISCONNECTED 0
#define SCAN_DONE TRUE
typedef enum {
PASSIVE_SCAN = 0,
ACTIVE_SCAN = 1,
} SCANTYPE_T;
typedef enum {
NO_POWERSAVE = 0,
MIN_FAST_PS = 1,
MAX_FAST_PS = 2,
MIN_PSPOLL_PS = 3,
MAX_PSPOLL_PS = 4
} USER_PS_MODE_T;
typedef enum {
CHIP_WAKEDUP = 0,
CHIP_SLEEPING_AUTO = 1,
CHIP_SLEEPING_MANUAL = 2
} CHIP_PS_STATE_T;
typedef enum {
ACQUIRE_ONLY = 0,
ACQUIRE_AND_WAKEUP = 1,
} BUS_ACQUIRE_T;
typedef enum {
RELEASE_ONLY = 0,
RELEASE_ALLOW_SLEEP = 1,
} BUS_RELEASE_T;
typedef enum {
NO_SECURITY = 0,
WEP_40 = 0x3,
WEP_104 = 0x7,
WPA_AES = 0x29,
WPA_TKIP = 0x49,
WPA_AES_TKIP = 0x69, /* Aes or Tkip */
WPA2_AES = 0x31,
WPA2_TKIP = 0x51,
WPA2_AES_TKIP = 0x71, /* Aes or Tkip */
} SECURITY_T;
enum AUTHTYPE {
OPEN_SYSTEM = 1,
SHARED_KEY = 2,
ANY = 3,
IEEE8021 = 5
};
enum SITESURVEY {
SITE_SURVEY_1CH = 0,
SITE_SURVEY_ALL_CH = 1,
SITE_SURVEY_OFF = 2
};
typedef enum {
NORMAL_ACK = 0,
NO_ACK,
} ACK_POLICY_T;
typedef enum {
DONT_RESET = 0,
DO_RESET = 1,
NO_REQUEST = 2,
} RESET_REQ_T;
typedef enum {
REKEY_DISABLE = 1,
REKEY_TIME_BASE,
REKEY_PKT_BASE,
REKEY_TIME_PKT_BASE
} RSNA_REKEY_POLICY_T;
typedef enum {
FILTER_NO = 0x00,
FILTER_AP_ONLY = 0x01,
FILTER_STA_ONLY = 0x02
} SCAN_CLASS_FITLER_T;
typedef enum {
PRI_HIGH_RSSI = 0x00,
PRI_LOW_RSSI = 0x04,
PRI_DETECT = 0x08
} SCAN_PRI_T;
typedef enum {
CH_FILTER_OFF = 0x00,
CH_FILTER_ON = 0x10
} CH_FILTER_T;
typedef enum {
AUTO_PROT = 0, /* Auto */
NO_PROT, /* Do not use any protection */
ERP_PROT, /* Protect all ERP frame exchanges */
HT_PROT, /* Protect all HT frame exchanges */
GF_PROT, /* Protect all GF frame exchanges */
} N_PROTECTION_MODE_T;
typedef enum {
G_SELF_CTS_PROT,
G_RTS_CTS_PROT,
} G_PROTECTION_MODE_T;
typedef enum {
HT_MIXED_MODE = 1,
HT_ONLY_20MHZ_MODE,
HT_ONLY_20_40MHZ_MODE,
} N_OPERATING_MODE_T;
typedef enum {
NO_DETECT = 0,
DETECT_ONLY = 1,
DETECT_PROTECT = 2,
DETECT_PROTECT_REPORT = 3,
} N_OBSS_DETECTION_T;
typedef enum {
RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */
FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */
LSIG_TXOP_PROT, /* LSIG TXOP Protection */
FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */
} N_PROTECTION_TYPE_T;
typedef enum {
STATIC_MODE = 1,
DYNAMIC_MODE = 2,
MIMO_MODE = 3, /* power save disable */
} N_SMPS_MODE_T;
typedef enum {
DISABLE_SELF_CTS,
ENABLE_SELF_CTS,
DISABLE_TX_ABORT,
ENABLE_TX_ABORT,
HW_TRIGGER_ABORT,
SW_TRIGGER_ABORT,
} TX_ABORT_OPTION_T;
enum wid_type {
WID_CHAR = 0,
WID_SHORT = 1,
WID_INT = 2,
WID_STR = 3,
WID_BIN_DATA = 4,
WID_BIN = 5,
WID_IP = 6,
WID_ADR = 7,
WID_UNDEF = 8,
WID_TYPE_FORCE_32BIT = 0xFFFFFFFF
};
struct wid {
u16 id;
enum wid_type type;
s32 size;
s8 *val;
};
typedef enum {
WID_NIL = 0xffff,
/*
* BSS Type
* -----------------------------------------------------------
* Configuration : Infrastructure Independent Access Point
* Values to set : 0 1 2
* -----------------------------------------------------------
*/
WID_BSS_TYPE = 0x0000,
/*
* Transmit Rate
* -----------------------------------------------------------
* Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54
* Values to set : 1 2 5 11 6 9 12 18 24 36 48 54
* -----------------------------------------------------------
*/
WID_CURRENT_TX_RATE = 0x0001,
/*
* Channel
* -----------------------------------------------------------
* Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
* Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
* -----------------------------------------------------------
*/
WID_CURRENT_CHANNEL = 0x0002,
/*
* Preamble
* -----------------------------------------------------------
* Configuration : short long Auto
* Values to set : 0 1 2
* -----------------------------------------------------------
*/
WID_PREAMBLE = 0x0003,
/*
* 11g operating mode (ignored if 11g not present)
* -----------------------------------------------------------
* Configuration : HighPerf Compat(RSet #1) Compat(RSet #2)
* Values to set : 1 2 3
* -----------------------------------------------------------
*/
WID_11G_OPERATING_MODE = 0x0004,
/*
* Mac status (response only)
* -----------------------------------------------------------
* Configuration : disconnect connect
* Values to get : 0 1
* -----------------------------------------------------------
*/
WID_STATUS = 0x0005,
/*
* Scan type
* -----------------------------------------------------------
* Configuration : Passive Scanning Active Scanning
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_SCAN_TYPE = 0x0007,
/*
* Key Id (WEP default key Id)
* -----------------------------------------------------------
* Configuration : Any value between 0 to 3
* Values to set : Same value. Default is 0
* -----------------------------------------------------------
*/
WID_KEY_ID = 0x0009,
/*
* QoS Enable
* -----------------------------------------------------------
* Configuration : QoS Disable WMM Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_QOS_ENABLE = 0x000A,
/*
* Power Management
* -----------------------------------------------------------
* Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
* Values to set : 0 1 2
* -----------------------------------------------------------
*/
WID_POWER_MANAGEMENT = 0x000B,
/*
* WEP/802 11I Configuration
* -----------------------------------------------------------
* Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
* Values (0x) : 00 03 07 29 49 31 51
* Configuration:WPA-AES+TKIP RSN-AES+TKIP
* Values (0x) : 69 71
* -----------------------------------------------------------
*/
WID_11I_MODE = 0x000C,
/*
* WEP Configuration: Used in BSS STA mode only when WEP is enabled
* -----------------------------------------------------------
* Configuration : Open System Shared Key Any Type | 802.1x Auth
* Values (0x) : 01 02 03 | BIT2
* -----------------------------------------------------------
*/
WID_AUTH_TYPE = 0x000D,
/*
* Site Survey Type
* -----------------------------------------------------------
* Configuration : Values to set
* Survey 1 Channel : 0
* survey all Channels : 1
* Disable Site Survey : 2
* -----------------------------------------------------------
*/
WID_SITE_SURVEY = 0x000E,
/*
* Listen Interval
* -----------------------------------------------------------
* Configuration : Any value between 1 to 255
* Values to set : Same value. Default is 3
* -----------------------------------------------------------
*/
WID_LISTEN_INTERVAL = 0x000F,
/*
* DTIM Period
* -----------------------------------------------------------
* Configuration : Any value between 1 to 255
* Values to set : Same value. Default is 3
* -----------------------------------------------------------
*/
WID_DTIM_PERIOD = 0x0010,
/*
* ACK Policy
* -----------------------------------------------------------
* Configuration : Normal Ack No Ack
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_ACK_POLICY = 0x0011,
/*
* Reset MAC (Set only)
* -----------------------------------------------------------
* Configuration : Don't Reset Reset No Request
* Values to set : 0 1 2
* -----------------------------------------------------------
*/
WID_RESET = 0x0012,
/*
* Broadcast SSID Option: Setting this will adhere to "" SSID element
* -----------------------------------------------------------
* Configuration : Enable Disable
* Values to set : 1 0
* -----------------------------------------------------------
*/
WID_BCAST_SSID = 0x0015,
/*
* Disconnect (Station)
* -----------------------------------------------------------
* Configuration : Association ID
* Values to set : Association ID
* -----------------------------------------------------------
*/
WID_DISCONNECT = 0x0016,
/*
* 11a Tx Power Level
* -----------------------------------------------------------
* Configuration : Sets TX Power (Higher the value greater the power)
* Values to set : Any value between 0 and 63 (inclusive Default 48)
* -----------------------------------------------------------
*/
WID_TX_POWER_LEVEL_11A = 0x0018,
/*
* Group Key Update Policy Selection
* -----------------------------------------------------------
* Configuration : Disabled timeBased packetBased timePacketBased
* Values to set : 1 2 3 4
* -----------------------------------------------------------
*/
WID_REKEY_POLICY = 0x0019,
/*
* Allow Short Slot
* -----------------------------------------------------------
* Configuration : Disallow Short Slot Allow Short Slot
* (Enable Only Long Slot) (Enable Short Slot if applicable)
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_SHORT_SLOT_ALLOWED = 0x001A,
WID_PHY_ACTIVE_REG = 0x001B,
/*
* 11b Tx Power Level
* -----------------------------------------------------------
* Configuration : Sets TX Power (Higher the value greater the power)
* Values to set : Any value between 0 and 63 (inclusive Default 48)
* -----------------------------------------------------------
*/
WID_TX_POWER_LEVEL_11B = 0x001D,
/*
* Scan Request
* -----------------------------------------------------------
* Configuration : Request default scan
* Values to set : 0
* -----------------------------------------------------------
*/
WID_START_SCAN_REQ = 0x001E,
/*
* Rssi (get only)
* -----------------------------------------------------------
* Configuration :
* Values to get : Rssi value
* -----------------------------------------------------------
*/
WID_RSSI = 0x001F,
/*
* Join Request
* -----------------------------------------------------------
* Configuration : Request to join
* Values to set : index of scan result
* -----------------------------------------------------------
*/
WID_JOIN_REQ = 0x0020,
WID_LINKSPEED = 0x0026,
/*
* Enable User Control of TX Power
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_USER_CONTROL_ON_TX_POWER = 0x0027,
WID_MEMORY_ACCESS_8BIT = 0x0029,
/*
* Enable Auto RX Sensitivity feature
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_AUTO_RX_SENSITIVITY = 0x0032,
/*
* Receive Buffer Based Ack
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_DATAFLOW_CONTROL = 0x0033,
/*
* Scan Filter
* -----------------------------------------------------------
* Configuration : Class No filter AP only Station Only
* Values to set : 0 1 2
* Configuration : Priority High Rssi Low Rssi Detect
* Values to set : 0 0x4 0x0
* Configuration : Channel filter off filter on
* Values to set : 0 0x10
* -----------------------------------------------------------
*/
WID_SCAN_FILTER = 0x0036,
/*
* Link Loss Threshold (measure in the beacon period)
* -----------------------------------------------------------
* Configuration : Any value between 10 and 254(Set to 255 disable)
* Values to set : Same value. Default is 10
* -----------------------------------------------------------
*/
WID_LINK_LOSS_THRESHOLD = 0x0037,
WID_ABORT_RUNNING_SCAN = 0x003E,
/* NMAC Character WID list */
WID_WPS_START = 0x0043,
/*
* Protection mode for MAC
* -----------------------------------------------------------
* Configuration : Auto No protection ERP HT GF
* Values to set : 0 1 2 3 4
* -----------------------------------------------------------
*/
WID_11N_PROT_MECH = 0x0080,
/*
* ERP Protection type for MAC
* -----------------------------------------------------------
* Configuration : Self-CTS RTS-CTS
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_11N_ERP_PROT_TYPE = 0x0081,
/*
* HT Option Enable
* -----------------------------------------------------------
* Configuration : HT Enable HT Disable
* Values to set : 1 0
* -----------------------------------------------------------
*/
WID_11N_ENABLE = 0x0082,
/*
* 11n Operating mode (Note that 11g operating mode will also be
* used in addition to this, if this is set to HT Mixed mode)
* -----------------------------------------------------------
* Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz
* Values to set : 1 2 3
* -----------------------------------------------------------
*/
WID_11N_OPERATING_MODE = 0x0083,
/*
* 11n OBSS non-HT STA Detection flag
* -----------------------------------------------------------
* Configuration : Do not detect
* Values to set : 0
* Configuration : Detect, do not protect or report
* Values to set : 1
* Configuration : Detect, protect and do not report
* Values to set : 2
* Configuration : Detect, protect and report to other BSS
* Values to set : 3
* -----------------------------------------------------------
*/
WID_11N_OBSS_NONHT_DETECTION = 0x0084,
/*
* 11n HT Protection Type
* -----------------------------------------------------------
* Configuration : RTS-CTS First Frame Exchange at non-HT-rate
* Values to set : 0 1
* Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt
* Values to set : 2 3
* -----------------------------------------------------------
*/
WID_11N_HT_PROT_TYPE = 0x0085,
/*
* 11n RIFS Protection Enable Flag
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_11N_RIFS_PROT_ENABLE = 0x0086,
/*
* SMPS Mode
* -----------------------------------------------------------
* Configuration : Static Dynamic MIMO (Power Save Disabled)
* Values to set : 1 2 3
* -----------------------------------------------------------
*/
WID_11N_SMPS_MODE = 0x0087,
/*
* Current transmit MCS
* -----------------------------------------------------------
* Configuration : MCS Index for data rate
* Values to set : 0 to 7
* -----------------------------------------------------------
*/
WID_11N_CURRENT_TX_MCS = 0x0088,
WID_11N_PRINT_STATS = 0x0089,
/*
* 11n Short GI Enable Flag
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_11N_SHORT_GI_ENABLE = 0x008D,
/*
* 11n RIFS Enable Flag
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_RIFS_MODE = 0x0094,
/*
* TX Abort Feature
* -----------------------------------------------------------
* Configuration : Disable Self CTS Enable Self CTS
* Values to set : 0 1
* Configuration : Disable TX Abort Enable TX Abort
* Values to set : 2 3
* Configuration : Enable HW TX Abort Enable SW TX Abort
* Values to set : 4 5
* -----------------------------------------------------------
*/
WID_TX_ABORT_CONFIG = 0x00A1,
WID_REG_TSSI_11B_VALUE = 0x00A6,
WID_REG_TSSI_11G_VALUE = 0x00A7,
WID_REG_TSSI_11N_VALUE = 0x00A8,
WID_TX_CALIBRATION = 0x00A9,
WID_DSCR_TSSI_11B_VALUE = 0x00AA,
WID_DSCR_TSSI_11G_VALUE = 0x00AB,
WID_DSCR_TSSI_11N_VALUE = 0x00AC,
/*
* Immediate Block-Ack Support
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 0 1
* -----------------------------------------------------------
*/
WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF,
/*
* TXOP Disable Flag
* -----------------------------------------------------------
* Configuration : Disable Enable
* Values to set : 1 0
* -----------------------------------------------------------
*/
WID_11N_TXOP_PROT_DISABLE = 0x00B0,
WID_TX_POWER_LEVEL_11N = 0x00B1,
/* Custom Character WID list */
WID_PC_TEST_MODE = 0x00C8,
/* SCAN Complete notification WID*/
WID_SCAN_COMPLETE = 0x00C9,
WID_DEL_BEACON = 0x00CA,
WID_LOGTerminal_Switch = 0x00CD,
WID_TX_POWER = 0x00CE,
/* EMAC Short WID list */
/* RTS Threshold */
/*
* -----------------------------------------------------------
* Configuration : Any value between 256 to 2347
* Values to set : Same value. Default is 2347
* -----------------------------------------------------------
*/
WID_RTS_THRESHOLD = 0x1000,
/*
* Fragmentation Threshold
* -----------------------------------------------------------
* Configuration : Any value between 256 to 2346
* Values to set : Same value. Default is 2346
* -----------------------------------------------------------
*/
WID_FRAG_THRESHOLD = 0x1001,
WID_SHORT_RETRY_LIMIT = 0x1002,
WID_LONG_RETRY_LIMIT = 0x1003,
WID_BEACON_INTERVAL = 0x1006,
WID_MEMORY_ACCESS_16BIT = 0x1008,
WID_RX_SENSE = 0x100B,
WID_ACTIVE_SCAN_TIME = 0x100C,
WID_PASSIVE_SCAN_TIME = 0x100D,
WID_SITE_SURVEY_SCAN_TIME = 0x100E,
WID_JOIN_START_TIMEOUT = 0x100F,
WID_AUTH_TIMEOUT = 0x1010,
WID_ASOC_TIMEOUT = 0x1011,
WID_11I_PROTOCOL_TIMEOUT = 0x1012,
WID_EAPOL_RESPONSE_TIMEOUT = 0x1013,
/* NMAC Short WID list */
WID_11N_SIG_QUAL_VAL = 0x1085,
WID_CCA_THRESHOLD = 0x1087,
/* Custom Short WID list */
/* EMAC Integer WID list */
WID_FAILED_COUNT = 0x2000,
WID_RETRY_COUNT = 0x2001,
WID_MULTIPLE_RETRY_COUNT = 0x2002,
WID_FRAME_DUPLICATE_COUNT = 0x2003,
WID_ACK_FAILURE_COUNT = 0x2004,
WID_RECEIVED_FRAGMENT_COUNT = 0x2005,
WID_MCAST_RECEIVED_FRAME_COUNT = 0x2006,
WID_FCS_ERROR_COUNT = 0x2007,
WID_SUCCESS_FRAME_COUNT = 0x2008,
WID_HUT_TX_COUNT = 0x200A,
WID_TX_FRAGMENT_COUNT = 0x200B,
WID_TX_MULTICAST_FRAME_COUNT = 0x200C,
WID_RTS_SUCCESS_COUNT = 0x200D,
WID_RTS_FAILURE_COUNT = 0x200E,
WID_WEP_UNDECRYPTABLE_COUNT = 0x200F,
WID_REKEY_PERIOD = 0x2010,
WID_REKEY_PACKET_COUNT = 0x2011,
WID_1X_SERV_ADDR = 0x2012,
WID_STACK_IP_ADDR = 0x2013,
WID_STACK_NETMASK_ADDR = 0x2014,
WID_HW_RX_COUNT = 0x2015,
WID_MEMORY_ADDRESS = 0x201E,
WID_MEMORY_ACCESS_32BIT = 0x201F,
WID_RF_REG_VAL = 0x2021,
/* NMAC Integer WID list */
WID_11N_PHY_ACTIVE_REG_VAL = 0x2080,
/* Custom Integer WID list */
WID_GET_INACTIVE_TIME = 0x2084,
WID_SET_OPERATION_MODE = 0X2086,
/* EMAC String WID list */
WID_SSID = 0x3000,
WID_FIRMWARE_VERSION = 0x3001,
WID_OPERATIONAL_RATE_SET = 0x3002,
WID_BSSID = 0x3003,
WID_WEP_KEY_VALUE = 0x3004,
WID_11I_PSK = 0x3008,
WID_11E_P_ACTION_REQ = 0x3009,
WID_1X_KEY = 0x300A,
WID_HARDWARE_VERSION = 0x300B,
WID_MAC_ADDR = 0x300C,
WID_HUT_DEST_ADDR = 0x300D,
WID_PHY_VERSION = 0x300F,
WID_SUPP_USERNAME = 0x3010,
WID_SUPP_PASSWORD = 0x3011,
WID_SITE_SURVEY_RESULTS = 0x3012,
WID_RX_POWER_LEVEL = 0x3013,
WID_DEL_ALL_RX_BA = 0x3014,
WID_SET_STA_MAC_INACTIVE_TIME = 0x3017,
WID_ADD_WEP_KEY = 0x3019,
WID_REMOVE_WEP_KEY = 0x301A,
WID_ADD_PTK = 0x301B,
WID_ADD_RX_GTK = 0x301C,
WID_ADD_TX_GTK = 0x301D,
WID_REMOVE_KEY = 0x301E,
WID_ASSOC_REQ_INFO = 0x301F,
WID_ASSOC_RES_INFO = 0x3020,
WID_MANUFACTURER = 0x3026, /*Added for CAPI tool */
WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */
WID_MODEL_NUM = 0x3028, /*Added for CAPI tool */
WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */
WID_SET_DRV_HANDLER = 0x3079,
/* NMAC String WID list */
WID_11N_P_ACTION_REQ = 0x3080,
WID_HUT_TEST_ID = 0x3081,
WID_PMKID_INFO = 0x3082,
WID_FIRMWARE_INFO = 0x3083,
WID_REGISTER_FRAME = 0x3084,
WID_DEL_ALL_STA = 0x3085,
WID_REMAIN_ON_CHAN = 0x3996,
WID_SSID_PROBE_REQ = 0x3997,
WID_JOIN_REQ_EXTENDED = 0x3998,
WID_IP_ADDRESS = 0x3999,
/* Custom String WID list */
/* EMAC Binary WID list */
WID_UAPSD_CONFIG = 0x4001,
WID_UAPSD_STATUS = 0x4002,
WID_WMM_AP_AC_PARAMS = 0x4003,
WID_WMM_STA_AC_PARAMS = 0x4004,
WID_NETWORK_INFO = 0x4005,
WID_STA_JOIN_INFO = 0x4006,
WID_CONNECTED_STA_LIST = 0x4007,
/* NMAC Binary WID list */
WID_11N_AUTORATE_TABLE = 0x4080,
WID_SCAN_CHANNEL_LIST = 0x4084,
WID_INFO_ELEMENT_PROBE = 0x4085,
WID_INFO_ELEMENT_ASSOCIATE = 0x4086,
WID_ADD_STA = 0X4087,
WID_REMOVE_STA = 0X4088,
WID_EDIT_STA = 0X4089,
WID_ADD_BEACON = 0x408a,
WID_SETUP_MULTICAST_FILTER = 0x408b,
/* Miscellaneous WIDs */
WID_ALL = 0x7FFE,
WID_MAX = 0xFFFF
} WID_T;
struct wilc;
int wilc_wlan_init(struct net_device *dev);
u32 wilc_get_chipid(struct wilc *wilc, bool update);
#endif
View git blame Copy permalink