9692c191ff
Both clock nodes in the current device tree are named "clock" and hence end up being the same node. Rename the nodes to different names to avoid this. In fact, fixed-clock uses the node name as the clock name, so name the nodes after the clock they represent. Move the clocks into a "clocks" sub-node to group them and avoid any possible naming conflicts with other nodes also named after the device type. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
112 lines
2.4 KiB
Plaintext
112 lines
2.4 KiB
Plaintext
/include/ "skeleton.dtsi"
|
|
|
|
/ {
|
|
compatible = "brcm,bcm2835";
|
|
model = "BCM2835";
|
|
interrupt-parent = <&intc>;
|
|
|
|
chosen {
|
|
bootargs = "earlyprintk console=ttyAMA0";
|
|
};
|
|
|
|
soc {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0x7e000000 0x20000000 0x02000000>;
|
|
|
|
timer {
|
|
compatible = "brcm,bcm2835-system-timer";
|
|
reg = <0x7e003000 0x1000>;
|
|
interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
|
|
clock-frequency = <1000000>;
|
|
};
|
|
|
|
intc: interrupt-controller {
|
|
compatible = "brcm,bcm2835-armctrl-ic";
|
|
reg = <0x7e00b200 0x200>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
watchdog {
|
|
compatible = "brcm,bcm2835-pm-wdt";
|
|
reg = <0x7e100000 0x28>;
|
|
};
|
|
|
|
uart@20201000 {
|
|
compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
|
|
reg = <0x7e201000 0x1000>;
|
|
interrupts = <2 25>;
|
|
clock-frequency = <3000000>;
|
|
};
|
|
|
|
gpio: gpio {
|
|
compatible = "brcm,bcm2835-gpio";
|
|
reg = <0x7e200000 0xb4>;
|
|
/*
|
|
* The GPIO IP block is designed for 3 banks of GPIOs.
|
|
* Each bank has a GPIO interrupt for itself.
|
|
* There is an overall "any bank" interrupt.
|
|
* In order, these are GIC interrupts 17, 18, 19, 20.
|
|
* Since the BCM2835 only has 2 banks, the 2nd bank
|
|
* interrupt output appears to be mirrored onto the
|
|
* 3rd bank's interrupt signal.
|
|
* So, a bank0 interrupt shows up on 17, 20, and
|
|
* a bank1 interrupt shows up on 18, 19, 20!
|
|
*/
|
|
interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
i2c0: i2c@20205000 {
|
|
compatible = "brcm,bcm2835-i2c";
|
|
reg = <0x7e205000 0x1000>;
|
|
interrupts = <2 21>;
|
|
clocks = <&clk_i2c>;
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c1: i2c@20804000 {
|
|
compatible = "brcm,bcm2835-i2c";
|
|
reg = <0x7e804000 0x1000>;
|
|
interrupts = <2 21>;
|
|
clocks = <&clk_i2c>;
|
|
status = "disabled";
|
|
};
|
|
|
|
sdhci: sdhci {
|
|
compatible = "brcm,bcm2835-sdhci";
|
|
reg = <0x7e300000 0x100>;
|
|
interrupts = <2 30>;
|
|
clocks = <&clk_mmc>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
clocks {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
clk_mmc: mmc {
|
|
compatible = "fixed-clock";
|
|
reg = <0>;
|
|
#clock-cells = <0>;
|
|
clock-frequency = <100000000>;
|
|
};
|
|
|
|
clk_i2c: i2c {
|
|
compatible = "fixed-clock";
|
|
reg = <1>;
|
|
#clock-cells = <0>;
|
|
clock-frequency = <150000000>;
|
|
};
|
|
};
|
|
};
|