redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/drivers/serial/8250_pci.c
David Ranson db1de1595d [PATCH] serial: MRi MRI-PCIDS1 dual port serial card 
Add support for the MRi PCIDS1 dual port serial card.  This card is a
little controversial since it is the subject of a PCI vendor/device ID
clash.  (See
http://www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html).  I have
for now just used the hex ID 0x950a.  The divisor was part calculated part
iterated, so may not be exactly correct (but works for me at all settings
between 300 - 115300 bps).

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-27 16:25:53 -07:00

2337 lines
56 KiB
C
Raw Blame History

/*
* linux/drivers/char/8250_pci.c
*
* Probe module for 8250/16550-type PCI serial ports.
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright (C) 2001 Russell King, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License.
*
* $Id: 8250_pci.c,v 1.28 2002/11/02 11:14:18 rmk Exp $
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/serial_core.h>
#include <linux/8250_pci.h>
#include <linux/bitops.h>
#include <asm/byteorder.h>
#include <asm/io.h>
#include "8250.h"
#undef SERIAL_DEBUG_PCI
/*
* Definitions for PCI support.
*/
#define FL_BASE_MASK 0x0007
#define FL_BASE0 0x0000
#define FL_BASE1 0x0001
#define FL_BASE2 0x0002
#define FL_BASE3 0x0003
#define FL_BASE4 0x0004
#define FL_GET_BASE(x) (x & FL_BASE_MASK)
/* Use successive BARs (PCI base address registers),
else use offset into some specified BAR */
#define FL_BASE_BARS 0x0008
/* do not assign an irq */
#define FL_NOIRQ 0x0080
/* Use the Base address register size to cap number of ports */
#define FL_REGION_SZ_CAP 0x0100
struct pci_board {
unsigned int flags;
unsigned int num_ports;
unsigned int base_baud;
unsigned int uart_offset;
unsigned int reg_shift;
unsigned int first_offset;
};
/*
* init function returns:
* > 0 - number of ports
* = 0 - use board->num_ports
* < 0 - error
*/
struct pci_serial_quirk {
u32 vendor;
u32 device;
u32 subvendor;
u32 subdevice;
int (*init)(struct pci_dev *dev);
int (*setup)(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx);
void (*exit)(struct pci_dev *dev);
};
#define PCI_NUM_BAR_RESOURCES 6
struct serial_private {
unsigned int nr;
void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES];
struct pci_serial_quirk *quirk;
int line[0];
};
static void moan_device(const char *str, struct pci_dev *dev)
{
printk(KERN_WARNING "%s: %s\n"
KERN_WARNING "Please send the output of lspci -vv, this\n"
KERN_WARNING "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
KERN_WARNING "manufacturer and name of serial board or\n"
KERN_WARNING "modem board to rmk+serial@arm.linux.org.uk.\n",
pci_name(dev), str, dev->vendor, dev->device,
dev->subsystem_vendor, dev->subsystem_device);
}
static int
setup_port(struct pci_dev *dev, struct uart_port *port,
int bar, int offset, int regshift)
{
struct serial_private *priv = pci_get_drvdata(dev);
unsigned long base, len;
if (bar >= PCI_NUM_BAR_RESOURCES)
return -EINVAL;
if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
base = pci_resource_start(dev, bar);
len = pci_resource_len(dev, bar);
if (!priv->remapped_bar[bar])
priv->remapped_bar[bar] = ioremap(base, len);
if (!priv->remapped_bar[bar])
return -ENOMEM;
port->iotype = UPIO_MEM;
port->mapbase = base + offset;
port->membase = priv->remapped_bar[bar] + offset;
port->regshift = regshift;
} else {
base = pci_resource_start(dev, bar) + offset;
port->iotype = UPIO_PORT;
port->iobase = base;
}
return 0;
}
/*
* AFAVLAB uses a different mixture of BARs and offsets
* Not that ugly ;) -- HW
*/
static int
afavlab_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
bar = FL_GET_BASE(board->flags);
if (idx < 4)
bar += idx;
else {
bar = 4;
offset += (idx - 4) * board->uart_offset;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* HP's Remote Management Console. The Diva chip came in several
* different versions. N-class, L2000 and A500 have two Diva chips, each
* with 3 UARTs (the third UART on the second chip is unused). Superdome
* and Keystone have one Diva chip with 3 UARTs. Some later machines have
* one Diva chip, but it has been expanded to 5 UARTs.
*/
static int __devinit pci_hp_diva_init(struct pci_dev *dev)
{
int rc = 0;
switch (dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_TOSCA1:
case PCI_DEVICE_ID_HP_DIVA_HALFDOME:
case PCI_DEVICE_ID_HP_DIVA_KEYSTONE:
case PCI_DEVICE_ID_HP_DIVA_EVEREST:
rc = 3;
break;
case PCI_DEVICE_ID_HP_DIVA_TOSCA2:
rc = 2;
break;
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
rc = 4;
break;
case PCI_DEVICE_ID_HP_DIVA_POWERBAR:
rc = 1;
break;
}
return rc;
}
/*
* HP's Diva chip puts the 4th/5th serial port further out, and
* some serial ports are supposed to be hidden on certain models.
*/
static int
pci_hp_diva_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int offset = board->first_offset;
unsigned int bar = FL_GET_BASE(board->flags);
switch (dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
if (idx == 3)
idx++;
break;
case PCI_DEVICE_ID_HP_DIVA_EVEREST:
if (idx > 0)
idx++;
if (idx > 2)
idx++;
break;
}
if (idx > 2)
offset = 0x18;
offset += idx * board->uart_offset;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* Added for EKF Intel i960 serial boards
*/
static int __devinit pci_inteli960ni_init(struct pci_dev *dev)
{
unsigned long oldval;
if (!(dev->subsystem_device & 0x1000))
return -ENODEV;
/* is firmware started? */
pci_read_config_dword(dev, 0x44, (void*) &oldval);
if (oldval == 0x00001000L) { /* RESET value */
printk(KERN_DEBUG "Local i960 firmware missing");
return -ENODEV;
}
return 0;
}
/*
* Some PCI serial cards using the PLX 9050 PCI interface chip require
* that the card interrupt be explicitly enabled or disabled. This
* seems to be mainly needed on card using the PLX which also use I/O
* mapped memory.
*/
static int __devinit pci_plx9050_init(struct pci_dev *dev)
{
u8 irq_config;
void __iomem *p;
if ((pci_resource_flags(dev, 0) & IORESOURCE_MEM) == 0) {
moan_device("no memory in bar 0", dev);
return 0;
}
irq_config = 0x41;
if (dev->vendor == PCI_VENDOR_ID_PANACOM)
irq_config = 0x43;
if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
(dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
/*
* As the megawolf cards have the int pins active
* high, and have 2 UART chips, both ints must be
* enabled on the 9050. Also, the UARTS are set in
* 16450 mode by default, so we have to enable the
* 16C950 'enhanced' mode so that we can use the
* deep FIFOs
*/
irq_config = 0x5b;
}
/*
* enable/disable interrupts
*/
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
writel(irq_config, p + 0x4c);
/*
* Read the register back to ensure that it took effect.
*/
readl(p + 0x4c);
iounmap(p);
return 0;
}
static void __devexit pci_plx9050_exit(struct pci_dev *dev)
{
u8 __iomem *p;
if ((pci_resource_flags(dev, 0) & IORESOURCE_MEM) == 0)
return;
/*
* disable interrupts
*/
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p != NULL) {
writel(0, p + 0x4c);
/*
* Read the register back to ensure that it took effect.
*/
readl(p + 0x4c);
iounmap(p);
}
}
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
sbs_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
bar = 0;
if (idx < 4) {
/* first four channels map to 0, 0x100, 0x200, 0x300 */
offset += idx * board->uart_offset;
} else if (idx < 8) {
/* last four channels map to 0x1000, 0x1100, 0x1200, 0x1300 */
offset += idx * board->uart_offset + 0xC00;
} else /* we have only 8 ports on PMC-OCTALPRO */
return 1;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* This does initialization for PMC OCTALPRO cards:
* maps the device memory, resets the UARTs (needed, bc
* if the module is removed and inserted again, the card
* is in the sleep mode) and enables global interrupt.
*/
/* global control register offset for SBS PMC-OctalPro */
#define OCT_REG_CR_OFF 0x500
static int __devinit sbs_init(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p == NULL)
return -ENOMEM;
/* Set bit-4 Control Register (UART RESET) in to reset the uarts */
writeb(0x10,p + OCT_REG_CR_OFF);
udelay(50);
writeb(0x0,p + OCT_REG_CR_OFF);
/* Set bit-2 (INTENABLE) of Control Register */
writeb(0x4, p + OCT_REG_CR_OFF);
iounmap(p);
return 0;
}
/*
* Disables the global interrupt of PMC-OctalPro
*/
static void __devexit sbs_exit(struct pci_dev *dev)
{
u8 __iomem *p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p != NULL) {
writeb(0, p + OCT_REG_CR_OFF);
}
iounmap(p);
}
/*
* SIIG serial cards have an PCI interface chip which also controls
* the UART clocking frequency. Each UART can be clocked independently
* (except cards equiped with 4 UARTs) and initial clocking settings
* are stored in the EEPROM chip. It can cause problems because this
* version of serial driver doesn't support differently clocked UART's
* on single PCI card. To prevent this, initialization functions set
* high frequency clocking for all UART's on given card. It is safe (I
* hope) because it doesn't touch EEPROM settings to prevent conflicts
* with other OSes (like M$ DOS).
*
* SIIG support added by Andrey Panin <pazke@donpac.ru>, 10/1999
*
* There is two family of SIIG serial cards with different PCI
* interface chip and different configuration methods:
* - 10x cards have control registers in IO and/or memory space;
* - 20x cards have control registers in standard PCI configuration space.
*
* There are also Quartet Serial cards which use Oxford Semiconductor
* 16954 quad UART PCI chip clocked by 18.432 MHz quartz.
*
* Note: some SIIG cards are probed by the parport_serial object.
*/
#define PCI_DEVICE_ID_SIIG_1S_10x (PCI_DEVICE_ID_SIIG_1S_10x_550 & 0xfffc)
#define PCI_DEVICE_ID_SIIG_2S_10x (PCI_DEVICE_ID_SIIG_2S_10x_550 & 0xfff8)
static int pci_siig10x_init(struct pci_dev *dev)
{
u16 data;
void __iomem *p;
switch (dev->device & 0xfff8) {
case PCI_DEVICE_ID_SIIG_1S_10x: /* 1S */
data = 0xffdf;
break;
case PCI_DEVICE_ID_SIIG_2S_10x: /* 2S, 2S1P */
data = 0xf7ff;
break;
default: /* 1S1P, 4S */
data = 0xfffb;
break;
}
p = ioremap(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
writew(readw(p + 0x28) & data, p + 0x28);
readw(p + 0x28);
iounmap(p);
return 0;
}
#define PCI_DEVICE_ID_SIIG_2S_20x (PCI_DEVICE_ID_SIIG_2S_20x_550 & 0xfffc)
#define PCI_DEVICE_ID_SIIG_2S1P_20x (PCI_DEVICE_ID_SIIG_2S1P_20x_550 & 0xfffc)
static int pci_siig20x_init(struct pci_dev *dev)
{
u8 data;
/* Change clock frequency for the first UART. */
pci_read_config_byte(dev, 0x6f, &data);
pci_write_config_byte(dev, 0x6f, data & 0xef);
/* If this card has 2 UART, we have to do the same with second UART. */
if (((dev->device & 0xfffc) == PCI_DEVICE_ID_SIIG_2S_20x) ||
((dev->device & 0xfffc) == PCI_DEVICE_ID_SIIG_2S1P_20x)) {
pci_read_config_byte(dev, 0x73, &data);
pci_write_config_byte(dev, 0x73, data & 0xef);
}
return 0;
}
int pci_siig10x_fn(struct pci_dev *dev, int enable)
{
int ret = 0;
if (enable)
ret = pci_siig10x_init(dev);
return ret;
}
int pci_siig20x_fn(struct pci_dev *dev, int enable)
{
int ret = 0;
if (enable)
ret = pci_siig20x_init(dev);
return ret;
}
EXPORT_SYMBOL(pci_siig10x_fn);
EXPORT_SYMBOL(pci_siig20x_fn);
/*
* Timedia has an explosion of boards, and to avoid the PCI table from
* growing *huge*, we use this function to collapse some 70 entries
* in the PCI table into one, for sanity's and compactness's sake.
*/
static unsigned short timedia_single_port[] = {
0x4025, 0x4027, 0x4028, 0x5025, 0x5027, 0
};
static unsigned short timedia_dual_port[] = {
0x0002, 0x4036, 0x4037, 0x4038, 0x4078, 0x4079, 0x4085,
0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
0x9137, 0x9138, 0x9237, 0x9238, 0xA079, 0xB079, 0xC079,
0xD079, 0
};
static unsigned short timedia_quad_port[] = {
0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
0x9256, 0x9257, 0xA056, 0xA157, 0xA158, 0xA159, 0xB056,
0xB157, 0
};
static unsigned short timedia_eight_port[] = {
0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
0x9167, 0x9168, 0xA066, 0xA167, 0xA168, 0
};
static struct timedia_struct {
int num;
unsigned short *ids;
} timedia_data[] = {
{ 1, timedia_single_port },
{ 2, timedia_dual_port },
{ 4, timedia_quad_port },
{ 8, timedia_eight_port },
{ 0, NULL }
};
static int __devinit pci_timedia_init(struct pci_dev *dev)
{
unsigned short *ids;
int i, j;
for (i = 0; timedia_data[i].num; i++) {
ids = timedia_data[i].ids;
for (j = 0; ids[j]; j++)
if (dev->subsystem_device == ids[j])
return timedia_data[i].num;
}
return 0;
}
/*
* Timedia/SUNIX uses a mixture of BARs and offsets
* Ugh, this is ugly as all hell --- TYT
*/
static int
pci_timedia_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
switch (idx) {
case 0:
bar = 0;
break;
case 1:
offset = board->uart_offset;
bar = 0;
break;
case 2:
bar = 1;
break;
case 3:
offset = board->uart_offset;
bar = 1;
case 4: /* BAR 2 */
case 5: /* BAR 3 */
case 6: /* BAR 4 */
case 7: /* BAR 5 */
bar = idx - 2;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/*
* Some Titan cards are also a little weird
*/
static int
titan_400l_800l_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
switch (idx) {
case 0:
bar = 1;
break;
case 1:
bar = 2;
break;
default:
bar = 4;
offset = (idx - 2) * board->uart_offset;
}
return setup_port(dev, port, bar, offset, board->reg_shift);
}
static int __devinit pci_xircom_init(struct pci_dev *dev)
{
msleep(100);
return 0;
}
static int __devinit pci_netmos_init(struct pci_dev *dev)
{
/* subdevice 0x00PS means <P> parallel, <S> serial */
unsigned int num_serial = dev->subsystem_device & 0xf;
if (num_serial == 0)
return -ENODEV;
return num_serial;
}
static int
pci_default_setup(struct pci_dev *dev, struct pci_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
bar = FL_GET_BASE(board->flags);
if (board->flags & FL_BASE_BARS)
bar += idx;
else
offset += idx * board->uart_offset;
maxnr = (pci_resource_len(dev, bar) - board->first_offset) /
(8 << board->reg_shift);
if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
return 1;
return setup_port(dev, port, bar, offset, board->reg_shift);
}
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
#define PCI_DEVICE_ID_OCTPRO 0x0001
#define PCI_SUBDEVICE_ID_OCTPRO232 0x0108
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
/*
* Master list of serial port init/setup/exit quirks.
* This does not describe the general nature of the port.
* (ie, baud base, number and location of ports, etc)
*
* This list is ordered alphabetically by vendor then device.
* Specific entries must come before more generic entries.
*/
static struct pci_serial_quirk pci_serial_quirks[] = {
/*
* AFAVLAB cards.
* It is not clear whether this applies to all products.
*/
{
.vendor = PCI_VENDOR_ID_AFAVLAB,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = afavlab_setup,
},
/*
* HP Diva
*/
{
.vendor = PCI_VENDOR_ID_HP,
.device = PCI_DEVICE_ID_HP_DIVA,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_hp_diva_init,
.setup = pci_hp_diva_setup,
},
/*
* Intel
*/
{
.vendor = PCI_VENDOR_ID_INTEL,
.device = PCI_DEVICE_ID_INTEL_80960_RP,
.subvendor = 0xe4bf,
.subdevice = PCI_ANY_ID,
.init = pci_inteli960ni_init,
.setup = pci_default_setup,
},
/*
* Panacom
*/
{
.vendor = PCI_VENDOR_ID_PANACOM,
.device = PCI_DEVICE_ID_PANACOM_QUADMODEM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
{
.vendor = PCI_VENDOR_ID_PANACOM,
.device = PCI_DEVICE_ID_PANACOM_DUALMODEM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
/*
* PLX
*/
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_9050,
.subvendor = PCI_SUBVENDOR_ID_KEYSPAN,
.subdevice = PCI_SUBDEVICE_ID_KEYSPAN_SX2,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
{
.vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_ROMULUS,
.subvendor = PCI_VENDOR_ID_PLX,
.subdevice = PCI_DEVICE_ID_PLX_ROMULUS,
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO232,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO422,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., P-Octal 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL232,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SBS Technologies, Inc., P-Octal 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL422,
.init = sbs_init,
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
/*
* SIIG cards.
* It is not clear whether these could be collapsed.
*/
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_10x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig10x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_1S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{ .vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_2S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_550,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_650,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
{
.vendor = PCI_VENDOR_ID_SIIG,
.device = PCI_DEVICE_ID_SIIG_4S_20x_850,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig20x_init,
.setup = pci_default_setup,
},
/*
* Titan cards
*/
{
.vendor = PCI_VENDOR_ID_TITAN,
.device = PCI_DEVICE_ID_TITAN_400L,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = titan_400l_800l_setup,
},
{
.vendor = PCI_VENDOR_ID_TITAN,
.device = PCI_DEVICE_ID_TITAN_800L,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = titan_400l_800l_setup,
},
/*
* Timedia cards
*/
{
.vendor = PCI_VENDOR_ID_TIMEDIA,
.device = PCI_DEVICE_ID_TIMEDIA_1889,
.subvendor = PCI_VENDOR_ID_TIMEDIA,
.subdevice = PCI_ANY_ID,
.init = pci_timedia_init,
.setup = pci_timedia_setup,
},
{
.vendor = PCI_VENDOR_ID_TIMEDIA,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_timedia_setup,
},
/*
* Xircom cards
*/
{
.vendor = PCI_VENDOR_ID_XIRCOM,
.device = PCI_DEVICE_ID_XIRCOM_X3201_MDM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_xircom_init,
.setup = pci_default_setup,
},
/*
* Netmos cards
*/
{
.vendor = PCI_VENDOR_ID_NETMOS,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_netmos_init,
.setup = pci_default_setup,
},
/*
* Default "match everything" terminator entry
*/
{
.vendor = PCI_ANY_ID,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_default_setup,
}
};
static inline int quirk_id_matches(u32 quirk_id, u32 dev_id)
{
return quirk_id == PCI_ANY_ID || quirk_id == dev_id;
}
static struct pci_serial_quirk *find_quirk(struct pci_dev *dev)
{
struct pci_serial_quirk *quirk;
for (quirk = pci_serial_quirks; ; quirk++)
if (quirk_id_matches(quirk->vendor, dev->vendor) &&
quirk_id_matches(quirk->device, dev->device) &&
quirk_id_matches(quirk->subvendor, dev->subsystem_vendor) &&
quirk_id_matches(quirk->subdevice, dev->subsystem_device))
break;
return quirk;
}
static _INLINE_ int
get_pci_irq(struct pci_dev *dev, struct pci_board *board, int idx)
{
if (board->flags & FL_NOIRQ)
return 0;
else
return dev->irq;
}
/*
* This is the configuration table for all of the PCI serial boards
* which we support. It is directly indexed by the pci_board_num_t enum
* value, which is encoded in the pci_device_id PCI probe table's
* driver_data member.
*
* The makeup of these names are:
* pbn_bn{_bt}_n_baud
*
* bn = PCI BAR number
* bt = Index using PCI BARs
* n = number of serial ports
* baud = baud rate
*
* This table is sorted by (in order): baud, bt, bn, n.
*
* Please note: in theory if n = 1, _bt infix should make no difference.
* ie, pbn_b0_1_115200 is the same as pbn_b0_bt_1_115200
*/
enum pci_board_num_t {
pbn_default = 0,
pbn_b0_1_115200,
pbn_b0_2_115200,
pbn_b0_4_115200,
pbn_b0_5_115200,
pbn_b0_1_921600,
pbn_b0_2_921600,
pbn_b0_4_921600,
pbn_b0_2_1130000,
pbn_b0_4_1152000,
pbn_b0_bt_1_115200,
pbn_b0_bt_2_115200,
pbn_b0_bt_8_115200,
pbn_b0_bt_1_460800,
pbn_b0_bt_2_460800,
pbn_b0_bt_4_460800,
pbn_b0_bt_1_921600,
pbn_b0_bt_2_921600,
pbn_b0_bt_4_921600,
pbn_b0_bt_8_921600,
pbn_b1_1_115200,
pbn_b1_2_115200,
pbn_b1_4_115200,
pbn_b1_8_115200,
pbn_b1_1_921600,
pbn_b1_2_921600,
pbn_b1_4_921600,
pbn_b1_8_921600,
pbn_b1_bt_2_921600,
pbn_b1_1_1382400,
pbn_b1_2_1382400,
pbn_b1_4_1382400,
pbn_b1_8_1382400,
pbn_b2_1_115200,
pbn_b2_8_115200,
pbn_b2_1_460800,
pbn_b2_4_460800,
pbn_b2_8_460800,
pbn_b2_16_460800,
pbn_b2_1_921600,
pbn_b2_4_921600,
pbn_b2_8_921600,
pbn_b2_bt_1_115200,
pbn_b2_bt_2_115200,
pbn_b2_bt_4_115200,
pbn_b2_bt_2_921600,
pbn_b2_bt_4_921600,
pbn_b3_4_115200,
pbn_b3_8_115200,
/*
* Board-specific versions.
*/
pbn_panacom,
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
pbn_oxsemi,
pbn_intel_i960,
pbn_sgi_ioc3,
pbn_nec_nile4,
pbn_computone_4,
pbn_computone_6,
pbn_computone_8,
pbn_sbsxrsio,
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
};
/*
* uart_offset - the space between channels
* reg_shift - describes how the UART registers are mapped
* to PCI memory by the card.
* For example IER register on SBS, Inc. PMC-OctPro is located at
* offset 0x10 from the UART base, while UART_IER is defined as 1
* in include/linux/serial_reg.h,
* see first lines of serial_in() and serial_out() in 8250.c
*/
static struct pci_board pci_boards[] __devinitdata = {
[pbn_default] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_1_115200] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_2_115200] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_4_115200] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_5_115200] = {
.flags = FL_BASE0,
.num_ports = 5,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_1_921600] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_2_921600] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_4_921600] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_2_1130000] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 1130000,
.uart_offset = 8,
},
[pbn_b0_4_1152000] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 1152000,
.uart_offset = 8,
},
[pbn_b0_bt_1_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_2_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_8_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b0_bt_1_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_2_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_4_460800] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b0_bt_1_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_2_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_4_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b0_bt_8_921600] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_1_115200] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_2_115200] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_4_115200] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_8_115200] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b1_1_921600] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_2_921600] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_4_921600] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_8_921600] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_bt_2_921600] = {
.flags = FL_BASE1|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b1_1_1382400] = {
.flags = FL_BASE1,
.num_ports = 1,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_2_1382400] = {
.flags = FL_BASE1,
.num_ports = 2,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_4_1382400] = {
.flags = FL_BASE1,
.num_ports = 4,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b1_8_1382400] = {
.flags = FL_BASE1,
.num_ports = 8,
.base_baud = 1382400,
.uart_offset = 8,
},
[pbn_b2_1_115200] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_8_115200] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_1_460800] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_4_460800] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_8_460800] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_16_460800] = {
.flags = FL_BASE2,
.num_ports = 16,
.base_baud = 460800,
.uart_offset = 8,
},
[pbn_b2_1_921600] = {
.flags = FL_BASE2,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_4_921600] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_8_921600] = {
.flags = FL_BASE2,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_bt_1_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_2_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_4_115200] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b2_bt_2_921600] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b2_bt_4_921600] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8,
},
[pbn_b3_4_115200] = {
.flags = FL_BASE3,
.num_ports = 4,
.base_baud = 115200,
.uart_offset = 8,
},
[pbn_b3_8_115200] = {
.flags = FL_BASE3,
.num_ports = 8,
.base_baud = 115200,
.uart_offset = 8,
},
/*
* Entries following this are board-specific.
*/
/*
* Panacom - IOMEM
*/
[pbn_panacom] = {
.flags = FL_BASE2,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
[pbn_panacom2] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
[pbn_panacom4] = {
.flags = FL_BASE2|FL_BASE_BARS,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x400,
.reg_shift = 7,
},
/* I think this entry is broken - the first_offset looks wrong --rmk */
[pbn_plx_romulus] = {
.flags = FL_BASE2,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 8 << 2,
.reg_shift = 2,
.first_offset = 0x03,
},
/*
* This board uses the size of PCI Base region 0 to
* signal now many ports are available
*/
[pbn_oxsemi] = {
.flags = FL_BASE0|FL_REGION_SZ_CAP,
.num_ports = 32,
.base_baud = 115200,
.uart_offset = 8,
},
/*
* EKF addition for i960 Boards form EKF with serial port.
* Max 256 ports.
*/
[pbn_intel_i960] = {
.flags = FL_BASE0,
.num_ports = 32,
.base_baud = 921600,
.uart_offset = 8 << 2,
.reg_shift = 2,
.first_offset = 0x10000,
},
[pbn_sgi_ioc3] = {
.flags = FL_BASE0|FL_NOIRQ,
.num_ports = 1,
.base_baud = 458333,
.uart_offset = 8,
.reg_shift = 0,
.first_offset = 0x20178,
},
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
*/
[pbn_nec_nile4] = {
.flags = FL_BASE0,
.num_ports = 1,
.base_baud = 520833,
.uart_offset = 8 << 3,
.reg_shift = 3,
.first_offset = 0x300,
},
/*
* Computone - uses IOMEM.
*/
[pbn_computone_4] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_computone_6] = {
.flags = FL_BASE0,
.num_ports = 6,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_computone_8] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 0x40,
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_sbsxrsio] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 460800,
.uart_offset = 256,
.reg_shift = 4,
},
/*
* Exar Corp. XR17C15[248] Dual/Quad/Octal UART
* Only basic 16550A support.
* XR17C15[24] are not tested, but they should work.
*/
[pbn_exar_XR17C152] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 921600,
.uart_offset = 0x200,
},
[pbn_exar_XR17C154] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 921600,
.uart_offset = 0x200,
},
[pbn_exar_XR17C158] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 921600,
.uart_offset = 0x200,
},
};
/*
* Given a complete unknown PCI device, try to use some heuristics to
* guess what the configuration might be, based on the pitiful PCI
* serial specs. Returns 0 on success, 1 on failure.
*/
static int __devinit
serial_pci_guess_board(struct pci_dev *dev, struct pci_board *board)
{
int num_iomem, num_port, first_port = -1, i;
/*
* If it is not a communications device or the programming
* interface is greater than 6, give up.
*
* (Should we try to make guesses for multiport serial devices
* later?)
*/
if ((((dev->class >> 8) != PCI_CLASS_COMMUNICATION_SERIAL) &&
((dev->class >> 8) != PCI_CLASS_COMMUNICATION_MODEM)) ||
(dev->class & 0xff) > 6)
return -ENODEV;
num_iomem = num_port = 0;
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (pci_resource_flags(dev, i) & IORESOURCE_IO) {
num_port++;
if (first_port == -1)
first_port = i;
}
if (pci_resource_flags(dev, i) & IORESOURCE_MEM)
num_iomem++;
}
/*
* If there is 1 or 0 iomem regions, and exactly one port,
* use it. We guess the number of ports based on the IO
* region size.
*/
if (num_iomem <= 1 && num_port == 1) {
board->flags = first_port;
board->num_ports = pci_resource_len(dev, first_port) / 8;
return 0;
}
/*
* Now guess if we've got a board which indexes by BARs.
* Each IO BAR should be 8 bytes, and they should follow
* consecutively.
*/
first_port = -1;
num_port = 0;
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (pci_resource_flags(dev, i) & IORESOURCE_IO &&
pci_resource_len(dev, i) == 8 &&
(first_port == -1 || (first_port + num_port) == i)) {
num_port++;
if (first_port == -1)
first_port = i;
}
}
if (num_port > 1) {
board->flags = first_port | FL_BASE_BARS;
board->num_ports = num_port;
return 0;
}
return -ENODEV;
}
static inline int
serial_pci_matches(struct pci_board *board, struct pci_board *guessed)
{
return
board->num_ports == guessed->num_ports &&
board->base_baud == guessed->base_baud &&
board->uart_offset == guessed->uart_offset &&
board->reg_shift == guessed->reg_shift &&
board->first_offset == guessed->first_offset;
}
/*
* Probe one serial board. Unfortunately, there is no rhyme nor reason
* to the arrangement of serial ports on a PCI card.
*/
static int __devinit
pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
{
struct serial_private *priv;
struct pci_board *board, tmp;
struct pci_serial_quirk *quirk;
int rc, nr_ports, i;
if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
ent->driver_data);
return -EINVAL;
}
board = &pci_boards[ent->driver_data];
rc = pci_enable_device(dev);
if (rc)
return rc;
if (ent->driver_data == pbn_default) {
/*
* Use a copy of the pci_board entry for this;
* avoid changing entries in the table.
*/
memcpy(&tmp, board, sizeof(struct pci_board));
board = &tmp;
/*
* We matched one of our class entries. Try to
* determine the parameters of this board.
*/
rc = serial_pci_guess_board(dev, board);
if (rc)
goto disable;
} else {
/*
* We matched an explicit entry. If we are able to
* detect this boards settings with our heuristic,
* then we no longer need this entry.
*/
memcpy(&tmp, &pci_boards[pbn_default], sizeof(struct pci_board));
rc = serial_pci_guess_board(dev, &tmp);
if (rc == 0 && serial_pci_matches(board, &tmp))
moan_device("Redundant entry in serial pci_table.",
dev);
}
nr_ports = board->num_ports;
/*
* Find an init and setup quirks.
*/
quirk = find_quirk(dev);
/*
* Run the new-style initialization function.
* The initialization function returns:
* <0 - error
* 0 - use board->num_ports
* >0 - number of ports
*/
if (quirk->init) {
rc = quirk->init(dev);
if (rc < 0)
goto disable;
if (rc)
nr_ports = rc;
}
priv = kmalloc(sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports,
GFP_KERNEL);
if (!priv) {
rc = -ENOMEM;
goto deinit;
}
memset(priv, 0, sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports);
priv->quirk = quirk;
pci_set_drvdata(dev, priv);
for (i = 0; i < nr_ports; i++) {
struct uart_port serial_port;
memset(&serial_port, 0, sizeof(struct uart_port));
serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF |
UPF_SHARE_IRQ;
serial_port.uartclk = board->base_baud * 16;
serial_port.irq = get_pci_irq(dev, board, i);
serial_port.dev = &dev->dev;
if (quirk->setup(dev, board, &serial_port, i))
break;
#ifdef SERIAL_DEBUG_PCI
printk("Setup PCI port: port %x, irq %d, type %d\n",
serial_port.iobase, serial_port.irq, serial_port.iotype);
#endif
priv->line[i] = serial8250_register_port(&serial_port);
if (priv->line[i] < 0) {
printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
break;
}
}
priv->nr = i;
return 0;
deinit:
if (quirk->exit)
quirk->exit(dev);
disable:
pci_disable_device(dev);
return rc;
}
static void __devexit pciserial_remove_one(struct pci_dev *dev)
{
struct serial_private *priv = pci_get_drvdata(dev);
struct pci_serial_quirk *quirk;
int i;
pci_set_drvdata(dev, NULL);
for (i = 0; i < priv->nr; i++)
serial8250_unregister_port(priv->line[i]);
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (priv->remapped_bar[i])
iounmap(priv->remapped_bar[i]);
priv->remapped_bar[i] = NULL;
}
/*
* Find the exit quirks.
*/
quirk = find_quirk(dev);
if (quirk->exit)
quirk->exit(dev);
pci_disable_device(dev);
kfree(priv);
}
static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
{
struct serial_private *priv = pci_get_drvdata(dev);
if (priv) {
int i;
for (i = 0; i < priv->nr; i++)
serial8250_suspend_port(priv->line[i]);
}
pci_save_state(dev);
pci_set_power_state(dev, pci_choose_state(dev, state));
return 0;
}
static int pciserial_resume_one(struct pci_dev *dev)
{
struct serial_private *priv = pci_get_drvdata(dev);
pci_set_power_state(dev, PCI_D0);
pci_restore_state(dev);
if (priv) {
int i;
/*
* The device may have been disabled. Re-enable it.
*/
pci_enable_device(dev);
/*
* Ensure that the board is correctly configured.
*/
if (priv->quirk->init)
priv->quirk->init(dev);
for (i = 0; i < priv->nr; i++)
serial8250_resume_port(priv->line[i]);
}
return 0;
}
static struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232, 0, 0,
pbn_b1_8_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232, 0, 0,
pbn_b1_4_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232, 0, 0,
pbn_b1_2_1382400 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485, 0, 0,
pbn_b1_2_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1, 0, 0,
pbn_b1_8_921600 },
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1, 0, 0,
pbn_b1_4_921600 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_1_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM422,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM232,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_GTEK_SERIAL2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM200,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
/*
* VScom SPCOM800, from sl@s.pl
*/
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_1077,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_4_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_KEYSPAN,
PCI_SUBDEVICE_ID_KEYSPAN_SX2, 0, 0,
pbn_panacom },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_QUADMODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_panacom4 },
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_DUALMODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_panacom2 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST8, 0, 0,
pbn_b2_8_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST16, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
PCI_SUBDEVICE_ID_CHASE_PCIRAS4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
pbn_b2_8_460800 },
/*
* Megawolf Romulus PCI Serial Card, from Mike Hudson
* (Exoray@isys.ca)
*/
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_ROMULUS,
0x10b5, 0x106a, 0, 0,
pbn_plx_romulus },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_2_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100D,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100M,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_SUBVENDOR_ID_SIIG, PCI_SUBDEVICE_ID_SIIG_QUARTET_SERIAL, 0, 0,
pbn_b0_4_1152000 },
/*
* The below card is a little controversial since it is the
* subject of a PCI vendor/device ID clash. (See
* www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html).
* For now just used the hex ID 0x950a.
*/
{ PCI_VENDOR_ID_OXSEMI, 0x950a,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_2_1130000 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_115200 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
/*
* SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
* from skokodyn@yahoo.com
*/
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO422, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL422, 0, 0,
pbn_sbsxrsio },
/*
* Digitan DS560-558, from jimd@esoft.com
*/
{ PCI_VENDOR_ID_ATT, PCI_DEVICE_ID_ATT_VENUS_MODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_115200 },
/*
* Titan Electronic cards
* The 400L and 800L have a custom setup quirk.
*/
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_2_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_bt_2_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_460800 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_10x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_550,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
/*
* Computone devices submitted by Doug McNash dmcnash@computone.com
*/
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG4,
0, 0, pbn_computone_4 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG8,
0, 0, pbn_computone_8 },
{ PCI_VENDOR_ID_COMPUTONE, PCI_DEVICE_ID_COMPUTONE_PG,
PCI_SUBVENDOR_ID_COMPUTONE, PCI_SUBDEVICE_ID_COMPUTONE_PG6,
0, 0, pbn_computone_6 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI95N,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_oxsemi },
{ PCI_VENDOR_ID_TIMEDIA, PCI_DEVICE_ID_TIMEDIA_1889,
PCI_VENDOR_ID_TIMEDIA, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_921600 },
/*
* AFAVLAB serial card, from Harald Welte <laforge@gnumonks.org>
*/
{ PCI_VENDOR_ID_AFAVLAB, PCI_DEVICE_ID_AFAVLAB_P028,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_115200 },
{ PCI_VENDOR_ID_AFAVLAB, PCI_DEVICE_ID_AFAVLAB_P030,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_8_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DSERIAL,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUATRO_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_OCTO_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_OCTO_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_PLUS,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_QUAD_B,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_460800 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_SSERIAL,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_115200 },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PORT_650,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_1_460800 },
/*
* Dell Remote Access Card 4 - Tim_T_Murphy@Dell.com
*/
{ PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_1382400 },
/*
* Dell Remote Access Card III - Tim_T_Murphy@Dell.com
*/
{ PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RACIII,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_1382400 },
/*
* RAStel 2 port modem, gerg@moreton.com.au
*/
{ PCI_VENDOR_ID_MORETON, PCI_DEVICE_ID_RASTEL_2PORT,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
/*
* EKF addition for i960 Boards form EKF with serial port
*/
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80960_RP,
0xE4BF, PCI_ANY_ID, 0, 0,
pbn_intel_i960 },
/*
* Xircom Cardbus/Ethernet combos
*/
{ PCI_VENDOR_ID_XIRCOM, PCI_DEVICE_ID_XIRCOM_X3201_MDM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* Xircom RBM56G cardbus modem - Dirk Arnold (temp entry)
*/
{ PCI_VENDOR_ID_XIRCOM, PCI_DEVICE_ID_XIRCOM_RBM56G,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* Untested PCI modems, sent in from various folks...
*/
/*
* Elsa Model 56K PCI Modem, from Andreas Rath <arh@01019freenet.de>
*/
{ PCI_VENDOR_ID_ROCKWELL, 0x1004,
0x1048, 0x1500, 0, 0,
pbn_b1_1_115200 },
{ PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
0xFF00, 0, 0, 0,
pbn_sgi_ioc3 },
/*
* HP Diva card
*/
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA,
PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_RMP3, 0, 0,
pbn_b1_1_115200 },
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_5_115200 },
{ PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_AUX,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_115200 },
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
*/
{ PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_NILE4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_nec_nile4 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b3_4_115200 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b3_8_115200 },
/*
* Exar Corp. XR17C15[248] Dual/Quad/Octal UART
*/
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C152 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C154 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C158 },
/*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
*/
{ PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
/*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
*/
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_SERIAL << 8,
0xffff00, pbn_default },
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_MODEM << 8,
0xffff00, pbn_default },
{ PCI_ANY_ID, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_COMMUNICATION_MULTISERIAL << 8,
0xffff00, pbn_default },
{ 0, }
};
static struct pci_driver serial_pci_driver = {
.name = "serial",
.probe = pciserial_init_one,
.remove = __devexit_p(pciserial_remove_one),
.suspend = pciserial_suspend_one,
.resume = pciserial_resume_one,
.id_table = serial_pci_tbl,
};
static int __init serial8250_pci_init(void)
{
return pci_register_driver(&serial_pci_driver);
}
static void __exit serial8250_pci_exit(void)
{
pci_unregister_driver(&serial_pci_driver);
}
module_init(serial8250_pci_init);
module_exit(serial8250_pci_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Generic 8250/16x50 PCI serial probe module");
MODULE_DEVICE_TABLE(pci, serial_pci_tbl);
View git blame Copy permalink