031ba1fd91
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
43 lines
1.8 KiB
Plaintext
43 lines
1.8 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
config WILC1000
|
|
tristate
|
|
help
|
|
This module only support IEEE 802.11n WiFi.
|
|
|
|
config WILC1000_SDIO
|
|
tristate "Atmel WILC1000 SDIO (WiFi only)"
|
|
depends on CFG80211 && INET && MMC
|
|
select WILC1000
|
|
help
|
|
This module adds support for the SDIO interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface.
|
|
It meets SDIO card specification version 2.0. The interface supports
|
|
the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz.
|
|
The host can use this interface to read and write from any register
|
|
within the chip as well as configure the WILC1000 for data DMA.
|
|
To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
|
this if your platform is using the SDIO bus.
|
|
|
|
config WILC1000_SPI
|
|
tristate "Atmel WILC1000 SPI (WiFi only)"
|
|
depends on CFG80211 && INET && SPI
|
|
select WILC1000
|
|
help
|
|
This module adds support for the SPI interface of adapters using
|
|
WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral
|
|
Interface (SPI) that operates as a SPI slave. This SPI interface can
|
|
be used for control and for serial I/O of 802.11 data. The SPI is a
|
|
full-duplex slave synchronous serial interface that is available
|
|
immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
|
|
VDDIO. Select this if your platform is using the SPI bus.
|
|
|
|
config WILC1000_HW_OOB_INTR
|
|
bool "WILC1000 out of band interrupt"
|
|
depends on WILC1000_SDIO
|
|
help
|
|
This option enables out-of-band interrupt support for the WILC1000
|
|
chipset. This OOB interrupt is intended to provide a faster interrupt
|
|
mechanism for SDIO host controllers that don't support SDIO interrupt.
|
|
Select this option If the SDIO host controller in your platform
|
|
doesn't support SDIO time devision interrupt.
|