22a9316702
The ST sensors on the Ux500 boards were not utilizing the IRQs for data ready sample triggers. Enable this by assigning the right GPIO lines and interrupt lines (when the GPIO lines are used for IRQs) to the accelerometer, gyro and magnetometer sensors. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
182 lines
4.1 KiB
Plaintext
182 lines
4.1 KiB
Plaintext
/*
|
|
* Copyright 2012 ST-Ericsson AB
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*
|
|
* Device Tree for the TVK1281618 UIB
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
|
|
|
|
button@139 {
|
|
/* Proximity sensor */
|
|
gpios = <&gpio6 25 0x4>;
|
|
linux,code = <11>; /* SW_FRONT_PROXIMITY */
|
|
label = "SFH7741 Proximity Sensor";
|
|
};
|
|
button@145 {
|
|
/* Hall sensor */
|
|
gpios = <&gpio4 17 0x4>;
|
|
linux,code = <0>; /* SW_LID */
|
|
label = "HED54XXU11 Hall Effect Sensor";
|
|
};
|
|
};
|
|
|
|
soc {
|
|
/* Add Synaptics touch screen, TC35893 keypad etc here */
|
|
i2c@80004000 {
|
|
tc35893@44 {
|
|
compatible = "toshiba,tc35893";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tc35893_tvk_mode>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
|
|
tc3589x_gpio {
|
|
compatible = "toshiba,tc3589x-gpio";
|
|
interrupts = <0>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
tc3589x_keypad {
|
|
compatible = "toshiba,tc3589x-keypad";
|
|
interrupts = <6>;
|
|
debounce-delay-ms = <4>;
|
|
keypad,num-columns = <8>;
|
|
keypad,num-rows = <8>;
|
|
linux,no-autorepeat;
|
|
linux,wakeup;
|
|
linux,keymap = <0x0301006b
|
|
0x04010066
|
|
0x06040072
|
|
0x040200d7
|
|
0x0303006a
|
|
0x0205000e
|
|
0x0607008b
|
|
0x0500001c
|
|
0x0403000b
|
|
0x03040034
|
|
0x05020067
|
|
0x0305006c
|
|
0x040500e7
|
|
0x0005009e
|
|
0x06020073
|
|
0x01030039
|
|
0x07060069
|
|
0x050500d9>;
|
|
};
|
|
};
|
|
};
|
|
/* Sensors mounted on this board variant */
|
|
i2c@80128000 {
|
|
lsm303dlh@18 {
|
|
/* Accelerometer */
|
|
compatible = "st,lsm303dlh-accel";
|
|
st,drdy-int-pin = <1>;
|
|
reg = <0x18>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
|
|
<19 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
lsm303dlh@1e {
|
|
/* Magnetometer */
|
|
compatible = "st,lsm303dlh-magn";
|
|
reg = <0x1e>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&magneto_tvk_mode>;
|
|
};
|
|
l3g4200d@68 {
|
|
/* Gyroscope */
|
|
compatible = "st,l3g4200d-gyro";
|
|
st,drdy-int-pin = <2>;
|
|
reg = <0x68>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
};
|
|
lsp001wm@5c {
|
|
/* Barometer/pressure sensor */
|
|
compatible = "st,lps001wp-press";
|
|
reg = <0x5c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
};
|
|
};
|
|
pinctrl {
|
|
/* Pull up this GPIO pin */
|
|
tc35893 {
|
|
tc35893_tvk_mode: tc35893_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO218_AH11";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
prox {
|
|
prox_tvk_mode: prox_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO217_AH12";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
hall {
|
|
hall_tvk_mode: hall_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO145_C13";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
accelerometer {
|
|
accel_tvk_mode: accel_tvk {
|
|
/* Accelerometer interrupt lines 1 & 2 */
|
|
tvk_cfg {
|
|
pins = "GPIO82_C1", "GPIO83_D3";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
magnetometer {
|
|
magneto_tvk_mode: magneto_tvk {
|
|
/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
|
|
tvk_cfg1 {
|
|
pins = "GPIO31_V3";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
tvk_cfg2 {
|
|
pins = "GPIO32_V2";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|