redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/arch/arm/kernel/perf_event_v6.c
Mark Rutland 3d1ff755e3 arm: perf: clean up PMU names 
The perf userspace tools can't handle dashes or spaces in PMU names,
which conflicts with the current naming scheme in the arm perf backend.
This prevents these PMUs from being accessed by name from the perf
tools. Additionally the ARMv6 pmus are named "v6", which does not fully
distinguish them in the sys/bus/event_source namespace.

This patch renames the PMUs consistently to a lower case form with
underscores, e.g. "armv6_1176", "armv7_cortex_a9". This is both readily
accepted by today's perf tool, and far easier to type than the
(apparently unused) convention in use previously. The OProfile name
conversion code is updated to handle this.

Due to a copy-paste error involving two "xscale1" entries, "xscale2" has
never been matched by the name OProfile name mapping. While we're
updating names, this is corrected.

Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[sachin: fixed missing semicolons in armv6 backend]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-07-02 15:48:25 +01:00

567 lines
18 KiB
C
Raw Blame History

/*
* ARMv6 Performance counter handling code.
*
* Copyright (C) 2009 picoChip Designs, Ltd., Jamie Iles
*
* ARMv6 has 2 configurable performance counters and a single cycle counter.
* They all share a single reset bit but can be written to zero so we can use
* that for a reset.
*
* The counters can't be individually enabled or disabled so when we remove
* one event and replace it with another we could get spurious counts from the
* wrong event. However, we can take advantage of the fact that the
* performance counters can export events to the event bus, and the event bus
* itself can be monitored. This requires that we *don't* export the events to
* the event bus. The procedure for disabling a configurable counter is:
* - change the counter to count the ETMEXTOUT[0] signal (0x20). This
* effectively stops the counter from counting.
* - disable the counter's interrupt generation (each counter has it's
* own interrupt enable bit).
* Once stopped, the counter value can be written as 0 to reset.
*
* To enable a counter:
* - enable the counter's interrupt generation.
* - set the new event type.
*
* Note: the dedicated cycle counter only counts cycles and can't be
* enabled/disabled independently of the others. When we want to disable the
* cycle counter, we have to just disable the interrupt reporting and start
* ignoring that counter. When re-enabling, we have to reset the value and
* enable the interrupt.
*/
#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K)
enum armv6_perf_types {
ARMV6_PERFCTR_ICACHE_MISS = 0x0,
ARMV6_PERFCTR_IBUF_STALL = 0x1,
ARMV6_PERFCTR_DDEP_STALL = 0x2,
ARMV6_PERFCTR_ITLB_MISS = 0x3,
ARMV6_PERFCTR_DTLB_MISS = 0x4,
ARMV6_PERFCTR_BR_EXEC = 0x5,
ARMV6_PERFCTR_BR_MISPREDICT = 0x6,
ARMV6_PERFCTR_INSTR_EXEC = 0x7,
ARMV6_PERFCTR_DCACHE_HIT = 0x9,
ARMV6_PERFCTR_DCACHE_ACCESS = 0xA,
ARMV6_PERFCTR_DCACHE_MISS = 0xB,
ARMV6_PERFCTR_DCACHE_WBACK = 0xC,
ARMV6_PERFCTR_SW_PC_CHANGE = 0xD,
ARMV6_PERFCTR_MAIN_TLB_MISS = 0xF,
ARMV6_PERFCTR_EXPL_D_ACCESS = 0x10,
ARMV6_PERFCTR_LSU_FULL_STALL = 0x11,
ARMV6_PERFCTR_WBUF_DRAINED = 0x12,
ARMV6_PERFCTR_CPU_CYCLES = 0xFF,
ARMV6_PERFCTR_NOP = 0x20,
};
enum armv6_counters {
ARMV6_CYCLE_COUNTER = 0,
ARMV6_COUNTER0,
ARMV6_COUNTER1,
};
/*
* The hardware events that we support. We do support cache operations but
* we have harvard caches and no way to combine instruction and data
* accesses/misses in hardware.
*/
static const unsigned armv6_perf_map[PERF_COUNT_HW_MAX] = {
PERF_MAP_ALL_UNSUPPORTED,
[PERF_COUNT_HW_CPU_CYCLES] = ARMV6_PERFCTR_CPU_CYCLES,
[PERF_COUNT_HW_INSTRUCTIONS] = ARMV6_PERFCTR_INSTR_EXEC,
[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = ARMV6_PERFCTR_BR_EXEC,
[PERF_COUNT_HW_BRANCH_MISSES] = ARMV6_PERFCTR_BR_MISPREDICT,
[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = ARMV6_PERFCTR_IBUF_STALL,
[PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = ARMV6_PERFCTR_LSU_FULL_STALL,
};
static const unsigned armv6_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
[PERF_COUNT_HW_CACHE_OP_MAX]
[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
PERF_CACHE_MAP_ALL_UNSUPPORTED,
/*
* The performance counters don't differentiate between read and write
* accesses/misses so this isn't strictly correct, but it's the best we
* can do. Writes and reads get combined.
*/
[C(L1D)][C(OP_READ)][C(RESULT_ACCESS)] = ARMV6_PERFCTR_DCACHE_ACCESS,
[C(L1D)][C(OP_READ)][C(RESULT_MISS)] = ARMV6_PERFCTR_DCACHE_MISS,
[C(L1D)][C(OP_WRITE)][C(RESULT_ACCESS)] = ARMV6_PERFCTR_DCACHE_ACCESS,
[C(L1D)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6_PERFCTR_DCACHE_MISS,
[C(L1I)][C(OP_READ)][C(RESULT_MISS)] = ARMV6_PERFCTR_ICACHE_MISS,
/*
* The ARM performance counters can count micro DTLB misses, micro ITLB
* misses and main TLB misses. There isn't an event for TLB misses, so
* use the micro misses here and if users want the main TLB misses they
* can use a raw counter.
*/
[C(DTLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV6_PERFCTR_DTLB_MISS,
[C(DTLB)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6_PERFCTR_DTLB_MISS,
[C(ITLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV6_PERFCTR_ITLB_MISS,
[C(ITLB)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6_PERFCTR_ITLB_MISS,
};
enum armv6mpcore_perf_types {
ARMV6MPCORE_PERFCTR_ICACHE_MISS = 0x0,
ARMV6MPCORE_PERFCTR_IBUF_STALL = 0x1,
ARMV6MPCORE_PERFCTR_DDEP_STALL = 0x2,
ARMV6MPCORE_PERFCTR_ITLB_MISS = 0x3,
ARMV6MPCORE_PERFCTR_DTLB_MISS = 0x4,
ARMV6MPCORE_PERFCTR_BR_EXEC = 0x5,
ARMV6MPCORE_PERFCTR_BR_NOTPREDICT = 0x6,
ARMV6MPCORE_PERFCTR_BR_MISPREDICT = 0x7,
ARMV6MPCORE_PERFCTR_INSTR_EXEC = 0x8,
ARMV6MPCORE_PERFCTR_DCACHE_RDACCESS = 0xA,
ARMV6MPCORE_PERFCTR_DCACHE_RDMISS = 0xB,
ARMV6MPCORE_PERFCTR_DCACHE_WRACCESS = 0xC,
ARMV6MPCORE_PERFCTR_DCACHE_WRMISS = 0xD,
ARMV6MPCORE_PERFCTR_DCACHE_EVICTION = 0xE,
ARMV6MPCORE_PERFCTR_SW_PC_CHANGE = 0xF,
ARMV6MPCORE_PERFCTR_MAIN_TLB_MISS = 0x10,
ARMV6MPCORE_PERFCTR_EXPL_MEM_ACCESS = 0x11,
ARMV6MPCORE_PERFCTR_LSU_FULL_STALL = 0x12,
ARMV6MPCORE_PERFCTR_WBUF_DRAINED = 0x13,
ARMV6MPCORE_PERFCTR_CPU_CYCLES = 0xFF,
};
/*
* The hardware events that we support. We do support cache operations but
* we have harvard caches and no way to combine instruction and data
* accesses/misses in hardware.
*/
static const unsigned armv6mpcore_perf_map[PERF_COUNT_HW_MAX] = {
PERF_MAP_ALL_UNSUPPORTED,
[PERF_COUNT_HW_CPU_CYCLES] = ARMV6MPCORE_PERFCTR_CPU_CYCLES,
[PERF_COUNT_HW_INSTRUCTIONS] = ARMV6MPCORE_PERFCTR_INSTR_EXEC,
[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = ARMV6MPCORE_PERFCTR_BR_EXEC,
[PERF_COUNT_HW_BRANCH_MISSES] = ARMV6MPCORE_PERFCTR_BR_MISPREDICT,
[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = ARMV6MPCORE_PERFCTR_IBUF_STALL,
[PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = ARMV6MPCORE_PERFCTR_LSU_FULL_STALL,
};
static const unsigned armv6mpcore_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
[PERF_COUNT_HW_CACHE_OP_MAX]
[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
PERF_CACHE_MAP_ALL_UNSUPPORTED,
[C(L1D)][C(OP_READ)][C(RESULT_ACCESS)] = ARMV6MPCORE_PERFCTR_DCACHE_RDACCESS,
[C(L1D)][C(OP_READ)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_DCACHE_RDMISS,
[C(L1D)][C(OP_WRITE)][C(RESULT_ACCESS)] = ARMV6MPCORE_PERFCTR_DCACHE_WRACCESS,
[C(L1D)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_DCACHE_WRMISS,
[C(L1I)][C(OP_READ)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_ICACHE_MISS,
/*
* The ARM performance counters can count micro DTLB misses, micro ITLB
* misses and main TLB misses. There isn't an event for TLB misses, so
* use the micro misses here and if users want the main TLB misses they
* can use a raw counter.
*/
[C(DTLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_DTLB_MISS,
[C(DTLB)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_DTLB_MISS,
[C(ITLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_ITLB_MISS,
[C(ITLB)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV6MPCORE_PERFCTR_ITLB_MISS,
};
static inline unsigned long
armv6_pmcr_read(void)
{
u32 val;
asm volatile("mrc p15, 0, %0, c15, c12, 0" : "=r"(val));
return val;
}
static inline void
armv6_pmcr_write(unsigned long val)
{
asm volatile("mcr p15, 0, %0, c15, c12, 0" : : "r"(val));
}
#define ARMV6_PMCR_ENABLE (1 << 0)
#define ARMV6_PMCR_CTR01_RESET (1 << 1)
#define ARMV6_PMCR_CCOUNT_RESET (1 << 2)
#define ARMV6_PMCR_CCOUNT_DIV (1 << 3)
#define ARMV6_PMCR_COUNT0_IEN (1 << 4)
#define ARMV6_PMCR_COUNT1_IEN (1 << 5)
#define ARMV6_PMCR_CCOUNT_IEN (1 << 6)
#define ARMV6_PMCR_COUNT0_OVERFLOW (1 << 8)
#define ARMV6_PMCR_COUNT1_OVERFLOW (1 << 9)
#define ARMV6_PMCR_CCOUNT_OVERFLOW (1 << 10)
#define ARMV6_PMCR_EVT_COUNT0_SHIFT 20
#define ARMV6_PMCR_EVT_COUNT0_MASK (0xFF << ARMV6_PMCR_EVT_COUNT0_SHIFT)
#define ARMV6_PMCR_EVT_COUNT1_SHIFT 12
#define ARMV6_PMCR_EVT_COUNT1_MASK (0xFF << ARMV6_PMCR_EVT_COUNT1_SHIFT)
#define ARMV6_PMCR_OVERFLOWED_MASK \
(ARMV6_PMCR_COUNT0_OVERFLOW | ARMV6_PMCR_COUNT1_OVERFLOW | \
ARMV6_PMCR_CCOUNT_OVERFLOW)
static inline int
armv6_pmcr_has_overflowed(unsigned long pmcr)
{
return pmcr & ARMV6_PMCR_OVERFLOWED_MASK;
}
static inline int
armv6_pmcr_counter_has_overflowed(unsigned long pmcr,
enum armv6_counters counter)
{
int ret = 0;
if (ARMV6_CYCLE_COUNTER == counter)
ret = pmcr & ARMV6_PMCR_CCOUNT_OVERFLOW;
else if (ARMV6_COUNTER0 == counter)
ret = pmcr & ARMV6_PMCR_COUNT0_OVERFLOW;
else if (ARMV6_COUNTER1 == counter)
ret = pmcr & ARMV6_PMCR_COUNT1_OVERFLOW;
else
WARN_ONCE(1, "invalid counter number (%d)\n", counter);
return ret;
}
static inline u32 armv6pmu_read_counter(struct perf_event *event)
{
struct hw_perf_event *hwc = &event->hw;
int counter = hwc->idx;
unsigned long value = 0;
if (ARMV6_CYCLE_COUNTER == counter)
asm volatile("mrc p15, 0, %0, c15, c12, 1" : "=r"(value));
else if (ARMV6_COUNTER0 == counter)
asm volatile("mrc p15, 0, %0, c15, c12, 2" : "=r"(value));
else if (ARMV6_COUNTER1 == counter)
asm volatile("mrc p15, 0, %0, c15, c12, 3" : "=r"(value));
else
WARN_ONCE(1, "invalid counter number (%d)\n", counter);
return value;
}
static inline void armv6pmu_write_counter(struct perf_event *event, u32 value)
{
struct hw_perf_event *hwc = &event->hw;
int counter = hwc->idx;
if (ARMV6_CYCLE_COUNTER == counter)
asm volatile("mcr p15, 0, %0, c15, c12, 1" : : "r"(value));
else if (ARMV6_COUNTER0 == counter)
asm volatile("mcr p15, 0, %0, c15, c12, 2" : : "r"(value));
else if (ARMV6_COUNTER1 == counter)
asm volatile("mcr p15, 0, %0, c15, c12, 3" : : "r"(value));
else
WARN_ONCE(1, "invalid counter number (%d)\n", counter);
}
static void armv6pmu_enable_event(struct perf_event *event)
{
unsigned long val, mask, evt, flags;
struct arm_pmu *cpu_pmu = to_arm_pmu(event->pmu);
struct hw_perf_event *hwc = &event->hw;
struct pmu_hw_events *events = cpu_pmu->get_hw_events();
int idx = hwc->idx;
if (ARMV6_CYCLE_COUNTER == idx) {
mask = 0;
evt = ARMV6_PMCR_CCOUNT_IEN;
} else if (ARMV6_COUNTER0 == idx) {
mask = ARMV6_PMCR_EVT_COUNT0_MASK;
evt = (hwc->config_base << ARMV6_PMCR_EVT_COUNT0_SHIFT) |
ARMV6_PMCR_COUNT0_IEN;
} else if (ARMV6_COUNTER1 == idx) {
mask = ARMV6_PMCR_EVT_COUNT1_MASK;
evt = (hwc->config_base << ARMV6_PMCR_EVT_COUNT1_SHIFT) |
ARMV6_PMCR_COUNT1_IEN;
} else {
WARN_ONCE(1, "invalid counter number (%d)\n", idx);
return;
}
/*
* Mask out the current event and set the counter to count the event
* that we're interested in.
*/
raw_spin_lock_irqsave(&events->pmu_lock, flags);
val = armv6_pmcr_read();
val &= ~mask;
val |= evt;
armv6_pmcr_write(val);
raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
}
static irqreturn_t
armv6pmu_handle_irq(int irq_num,
void *dev)
{
unsigned long pmcr = armv6_pmcr_read();
struct perf_sample_data data;
struct arm_pmu *cpu_pmu = (struct arm_pmu *)dev;
struct pmu_hw_events *cpuc = cpu_pmu->get_hw_events();
struct pt_regs *regs;
int idx;
if (!armv6_pmcr_has_overflowed(pmcr))
return IRQ_NONE;
regs = get_irq_regs();
/*
* The interrupts are cleared by writing the overflow flags back to
* the control register. All of the other bits don't have any effect
* if they are rewritten, so write the whole value back.
*/
armv6_pmcr_write(pmcr);
for (idx = 0; idx < cpu_pmu->num_events; ++idx) {
struct perf_event *event = cpuc->events[idx];
struct hw_perf_event *hwc;
/* Ignore if we don't have an event. */
if (!event)
continue;
/*
* We have a single interrupt for all counters. Check that
* each counter has overflowed before we process it.
*/
if (!armv6_pmcr_counter_has_overflowed(pmcr, idx))
continue;
hwc = &event->hw;
armpmu_event_update(event);
perf_sample_data_init(&data, 0, hwc->last_period);
if (!armpmu_event_set_period(event))
continue;
if (perf_event_overflow(event, &data, regs))
cpu_pmu->disable(event);
}
/*
* Handle the pending perf events.
*
* Note: this call *must* be run with interrupts disabled. For
* platforms that can have the PMU interrupts raised as an NMI, this
* will not work.
*/
irq_work_run();
return IRQ_HANDLED;
}
static void armv6pmu_start(struct arm_pmu *cpu_pmu)
{
unsigned long flags, val;
struct pmu_hw_events *events = cpu_pmu->get_hw_events();
raw_spin_lock_irqsave(&events->pmu_lock, flags);
val = armv6_pmcr_read();
val |= ARMV6_PMCR_ENABLE;
armv6_pmcr_write(val);
raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
}
static void armv6pmu_stop(struct arm_pmu *cpu_pmu)
{
unsigned long flags, val;
struct pmu_hw_events *events = cpu_pmu->get_hw_events();
raw_spin_lock_irqsave(&events->pmu_lock, flags);
val = armv6_pmcr_read();
val &= ~ARMV6_PMCR_ENABLE;
armv6_pmcr_write(val);
raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
}
static int
armv6pmu_get_event_idx(struct pmu_hw_events *cpuc,
struct perf_event *event)
{
struct hw_perf_event *hwc = &event->hw;
/* Always place a cycle counter into the cycle counter. */
if (ARMV6_PERFCTR_CPU_CYCLES == hwc->config_base) {
if (test_and_set_bit(ARMV6_CYCLE_COUNTER, cpuc->used_mask))
return -EAGAIN;
return ARMV6_CYCLE_COUNTER;
} else {
/*
* For anything other than a cycle counter, try and use
* counter0 and counter1.
*/
if (!test_and_set_bit(ARMV6_COUNTER1, cpuc->used_mask))
return ARMV6_COUNTER1;
if (!test_and_set_bit(ARMV6_COUNTER0, cpuc->used_mask))
return ARMV6_COUNTER0;
/* The counters are all in use. */
return -EAGAIN;
}
}
static void armv6pmu_disable_event(struct perf_event *event)
{
unsigned long val, mask, evt, flags;
struct arm_pmu *cpu_pmu = to_arm_pmu(event->pmu);
struct hw_perf_event *hwc = &event->hw;
struct pmu_hw_events *events = cpu_pmu->get_hw_events();
int idx = hwc->idx;
if (ARMV6_CYCLE_COUNTER == idx) {
mask = ARMV6_PMCR_CCOUNT_IEN;
evt = 0;
} else if (ARMV6_COUNTER0 == idx) {
mask = ARMV6_PMCR_COUNT0_IEN | ARMV6_PMCR_EVT_COUNT0_MASK;
evt = ARMV6_PERFCTR_NOP << ARMV6_PMCR_EVT_COUNT0_SHIFT;
} else if (ARMV6_COUNTER1 == idx) {
mask = ARMV6_PMCR_COUNT1_IEN | ARMV6_PMCR_EVT_COUNT1_MASK;
evt = ARMV6_PERFCTR_NOP << ARMV6_PMCR_EVT_COUNT1_SHIFT;
} else {
WARN_ONCE(1, "invalid counter number (%d)\n", idx);
return;
}
/*
* Mask out the current event and set the counter to count the number
* of ETM bus signal assertion cycles. The external reporting should
* be disabled and so this should never increment.
*/
raw_spin_lock_irqsave(&events->pmu_lock, flags);
val = armv6_pmcr_read();
val &= ~mask;
val |= evt;
armv6_pmcr_write(val);
raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
}
static void armv6mpcore_pmu_disable_event(struct perf_event *event)
{
unsigned long val, mask, flags, evt = 0;
struct arm_pmu *cpu_pmu = to_arm_pmu(event->pmu);
struct hw_perf_event *hwc = &event->hw;
struct pmu_hw_events *events = cpu_pmu->get_hw_events();
int idx = hwc->idx;
if (ARMV6_CYCLE_COUNTER == idx) {
mask = ARMV6_PMCR_CCOUNT_IEN;
} else if (ARMV6_COUNTER0 == idx) {
mask = ARMV6_PMCR_COUNT0_IEN;
} else if (ARMV6_COUNTER1 == idx) {
mask = ARMV6_PMCR_COUNT1_IEN;
} else {
WARN_ONCE(1, "invalid counter number (%d)\n", idx);
return;
}
/*
* Unlike UP ARMv6, we don't have a way of stopping the counters. We
* simply disable the interrupt reporting.
*/
raw_spin_lock_irqsave(&events->pmu_lock, flags);
val = armv6_pmcr_read();
val &= ~mask;
val |= evt;
armv6_pmcr_write(val);
raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
}
static int armv6_map_event(struct perf_event *event)
{
return armpmu_map_event(event, &armv6_perf_map,
&armv6_perf_cache_map, 0xFF);
}
static void armv6pmu_init(struct arm_pmu *cpu_pmu)
{
cpu_pmu->handle_irq = armv6pmu_handle_irq;
cpu_pmu->enable = armv6pmu_enable_event;
cpu_pmu->disable = armv6pmu_disable_event;
cpu_pmu->read_counter = armv6pmu_read_counter;
cpu_pmu->write_counter = armv6pmu_write_counter;
cpu_pmu->get_event_idx = armv6pmu_get_event_idx;
cpu_pmu->start = armv6pmu_start;
cpu_pmu->stop = armv6pmu_stop;
cpu_pmu->map_event = armv6_map_event;
cpu_pmu->num_events = 3;
cpu_pmu->max_period = (1LLU << 32) - 1;
}
static int armv6_1136_pmu_init(struct arm_pmu *cpu_pmu)
{
armv6pmu_init(cpu_pmu);
cpu_pmu->name = "armv6_1136";
return 0;
}
static int armv6_1156_pmu_init(struct arm_pmu *cpu_pmu)
{
armv6pmu_init(cpu_pmu);
cpu_pmu->name = "armv6_1156";
return 0;
}
static int armv6_1176_pmu_init(struct arm_pmu *cpu_pmu)
{
armv6pmu_init(cpu_pmu);
cpu_pmu->name = "armv6_1176";
return 0;
}
/*
* ARMv6mpcore is almost identical to single core ARMv6 with the exception
* that some of the events have different enumerations and that there is no
* *hack* to stop the programmable counters. To stop the counters we simply
* disable the interrupt reporting and update the event. When unthrottling we
* reset the period and enable the interrupt reporting.
*/
static int armv6mpcore_map_event(struct perf_event *event)
{
return armpmu_map_event(event, &armv6mpcore_perf_map,
&armv6mpcore_perf_cache_map, 0xFF);
}
static int armv6mpcore_pmu_init(struct arm_pmu *cpu_pmu)
{
cpu_pmu->name = "armv6_11mpcore";
cpu_pmu->handle_irq = armv6pmu_handle_irq;
cpu_pmu->enable = armv6pmu_enable_event;
cpu_pmu->disable = armv6mpcore_pmu_disable_event;
cpu_pmu->read_counter = armv6pmu_read_counter;
cpu_pmu->write_counter = armv6pmu_write_counter;
cpu_pmu->get_event_idx = armv6pmu_get_event_idx;
cpu_pmu->start = armv6pmu_start;
cpu_pmu->stop = armv6pmu_stop;
cpu_pmu->map_event = armv6mpcore_map_event;
cpu_pmu->num_events = 3;
cpu_pmu->max_period = (1LLU << 32) - 1;
return 0;
}
#else
static int armv6_1136_pmu_init(struct arm_pmu *cpu_pmu)
{
return -ENODEV;
}
static int armv6_1156_pmu_init(struct arm_pmu *cpu_pmu)
{
return -ENODEV;
}
static int armv6_1176_pmu_init(struct arm_pmu *cpu_pmu)
{
return -ENODEV;
}
static int armv6mpcore_pmu_init(struct arm_pmu *cpu_pmu)
{
return -ENODEV;
}
#endif /* CONFIG_CPU_V6 || CONFIG_CPU_V6K */
View git blame Copy permalink