redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/arch/arm/mach-shmobile/board-kzm9g.c
Linus Torvalds 44c916d58b ARM: SoC cleanups for 3.17 
This merge window brings a good size of cleanups on various
 platforms. Among the bigger ones:
 
 * Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
   lacked active support for quite a while, and after asking around nobody
   showed interest in keeping them around. If needed, they could be
   resurrected in the future but it's more likely that we would prefer
   reintroduction of them as DT and multiplatform-enabled platforms
   instead.
 * OMAP4 controller code register define diet. They defined a lot of registers
   that were never actually used, etc.
 * Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
   to drivers/soc so it can be shared with 64-bit code. This also converts them
   over to traditional driver models where possible.
 * Removal of legacy gpio-samsung driver, since the last users have been
   removed (moved to pinctrl)
 
 Plus a bunch of smaller changes for various platforms that sort of
 dissapear in the diffstat for the above. clps711x cleanups, shmobile
 header file refactoring/moves for multiplatform friendliness, some misc
 cleanups, etc.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
 POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
 EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
 927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
 VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
 8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
 465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
 xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
 ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
 aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
 AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
 wpmxJTASGxcfuZZgKXm7
 =gbcE
 -----END PGP SIGNATURE-----

Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This merge window brings a good size of cleanups on various platforms.
  Among the bigger ones:

   - Removal of Samsung s5pc100 and s5p64xx platforms.  Both of these
     have lacked active support for quite a while, and after asking
     around nobody showed interest in keeping them around.  If needed,
     they could be resurrected in the future but it's more likely that
     we would prefer reintroduction of them as DT and
     multiplatform-enabled platforms instead.

   - OMAP4 controller code register define diet.  They defined a lot of
     registers that were never actually used, etc.

   - Move of some of the Tegra platform code (PMC, APBIO, fuse,
     powergate) to drivers/soc so it can be shared with 64-bit code.
     This also converts them over to traditional driver models where
     possible.

   - Removal of legacy gpio-samsung driver, since the last users have
     been removed (moved to pinctrl)

  Plus a bunch of smaller changes for various platforms that sort of
  dissapear in the diffstat for the above.  clps711x cleanups, shmobile
  header file refactoring/moves for multiplatform friendliness, some
  misc cleanups, etc"

* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
  drivers: CCI: Correct use of ! and &
  video: clcd-versatile: Depend on ARM
  video: fix up versatile CLCD helper move
  MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
  ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
  MAINTAINERS: Remove Kirkwood
  ARM: tegra: Convert PMC to a driver
  soc/tegra: fuse: Set up in early initcall
  ARM: tegra: Always lock the CPU reset vector
  ARM: tegra: Setup CPU hotplug in a pure initcall
  soc/tegra: Implement runtime check for Tegra SoCs
  soc/tegra: fuse: fix dummy functions
  soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
  soc/tegra: Add efuse and apbmisc bindings
  soc/tegra: Add efuse driver for Tegra
  ARM: tegra: move fuse exports to soc/tegra/fuse.h
  ARM: tegra: export apb dma readl/writel
  ARM: tegra: Use a function to get the chip ID
  ARM: tegra: Sort includes alphabetically
  ARM: tegra: Move includes to include/soc/tegra
  ...
2014-08-08 11:00:26 -07:00

921 lines
22 KiB
C
Raw Blame History

/*
* KZM-A9-GT board support
*
* Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/i2c.h>
#include <linux/i2c/pcf857x.h>
#include <linux/input.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sh_mmcif.h>
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/mfd/as3711.h>
#include <linux/mfd/tmio.h>
#include <linux/pinctrl/machine.h>
#include <linux/pinctrl/pinconf-generic.h>
#include <linux/platform_device.h>
#include <linux/reboot.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/usb/r8a66597.h>
#include <linux/usb/renesas_usbhs.h>
#include <linux/videodev2.h>
#include <sound/sh_fsi.h>
#include <sound/simple_card.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <video/sh_mobile_lcdc.h>
#include "common.h"
#include "irqs.h"
#include "sh73a0.h"
/*
* external GPIO
*/
#define GPIO_PCF8575_BASE (310)
#define GPIO_PCF8575_PORT10 (GPIO_PCF8575_BASE + 8)
#define GPIO_PCF8575_PORT11 (GPIO_PCF8575_BASE + 9)
#define GPIO_PCF8575_PORT12 (GPIO_PCF8575_BASE + 10)
#define GPIO_PCF8575_PORT13 (GPIO_PCF8575_BASE + 11)
#define GPIO_PCF8575_PORT14 (GPIO_PCF8575_BASE + 12)
#define GPIO_PCF8575_PORT15 (GPIO_PCF8575_BASE + 13)
#define GPIO_PCF8575_PORT16 (GPIO_PCF8575_BASE + 14)
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
};
/*
* FSI-AK4648
*
* this command is required when playback.
*
* # amixer set "LINEOUT Mixer DACL" on
*/
/* SMSC 9221 */
static struct resource smsc9221_resources[] = {
[0] = {
.start = 0x10000000, /* CS4 */
.end = 0x100000ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = irq_pin(3), /* IRQ3 */
.flags = IORESOURCE_IRQ,
},
};
static struct smsc911x_platform_config smsc9221_platdata = {
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
.phy_interface = PHY_INTERFACE_MODE_MII,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
};
static struct platform_device smsc_device = {
.name = "smsc911x",
.dev = {
.platform_data = &smsc9221_platdata,
},
.resource = smsc9221_resources,
.num_resources = ARRAY_SIZE(smsc9221_resources),
};
/* USB external chip */
static struct r8a66597_platdata usb_host_data = {
.on_chip = 0,
.xtal = R8A66597_PLATDATA_XTAL_48MHZ,
};
static struct resource usb_resources[] = {
[0] = {
.start = 0x10010000,
.end = 0x1001ffff - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = irq_pin(1), /* IRQ1 */
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device usb_host_device = {
.name = "r8a66597_hcd",
.dev = {
.platform_data = &usb_host_data,
.dma_mask = NULL,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(usb_resources),
.resource = usb_resources,
};
/* USB Func CN17 */
struct usbhs_private {
void __iomem *phy;
void __iomem *cr2;
struct renesas_usbhs_platform_info info;
};
#define IRQ15 irq_pin(15)
#define USB_PHY_MODE (1 << 4)
#define USB_PHY_INT_EN ((1 << 3) | (1 << 2))
#define USB_PHY_ON (1 << 1)
#define USB_PHY_OFF (1 << 0)
#define USB_PHY_INT_CLR (USB_PHY_ON | USB_PHY_OFF)
#define usbhs_get_priv(pdev) \
container_of(renesas_usbhs_get_info(pdev), struct usbhs_private, info)
static int usbhs_get_vbus(struct platform_device *pdev)
{
struct usbhs_private *priv = usbhs_get_priv(pdev);
return !((1 << 7) & __raw_readw(priv->cr2));
}
static int usbhs_phy_reset(struct platform_device *pdev)
{
struct usbhs_private *priv = usbhs_get_priv(pdev);
/* init phy */
__raw_writew(0x8a0a, priv->cr2);
return 0;
}
static int usbhs_get_id(struct platform_device *pdev)
{
return USBHS_GADGET;
}
static irqreturn_t usbhs_interrupt(int irq, void *data)
{
struct platform_device *pdev = data;
struct usbhs_private *priv = usbhs_get_priv(pdev);
renesas_usbhs_call_notify_hotplug(pdev);
/* clear status */
__raw_writew(__raw_readw(priv->phy) | USB_PHY_INT_CLR, priv->phy);
return IRQ_HANDLED;
}
static int usbhs_hardware_init(struct platform_device *pdev)
{
struct usbhs_private *priv = usbhs_get_priv(pdev);
int ret;
/* clear interrupt status */
__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
ret = request_irq(IRQ15, usbhs_interrupt, IRQF_TRIGGER_HIGH,
dev_name(&pdev->dev), pdev);
if (ret) {
dev_err(&pdev->dev, "request_irq err\n");
return ret;
}
/* enable USB phy interrupt */
__raw_writew(USB_PHY_MODE | USB_PHY_INT_EN, priv->phy);
return 0;
}
static int usbhs_hardware_exit(struct platform_device *pdev)
{
struct usbhs_private *priv = usbhs_get_priv(pdev);
/* clear interrupt status */
__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
free_irq(IRQ15, pdev);
return 0;
}
static u32 usbhs_pipe_cfg[] = {
USB_ENDPOINT_XFER_CONTROL,
USB_ENDPOINT_XFER_ISOC,
USB_ENDPOINT_XFER_ISOC,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_INT,
USB_ENDPOINT_XFER_INT,
USB_ENDPOINT_XFER_INT,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
USB_ENDPOINT_XFER_BULK,
};
static struct usbhs_private usbhs_private = {
.phy = IOMEM(0xe60781e0), /* USBPHYINT */
.cr2 = IOMEM(0xe605810c), /* USBCR2 */
.info = {
.platform_callback = {
.hardware_init = usbhs_hardware_init,
.hardware_exit = usbhs_hardware_exit,
.get_id = usbhs_get_id,
.phy_reset = usbhs_phy_reset,
.get_vbus = usbhs_get_vbus,
},
.driver_param = {
.buswait_bwait = 4,
.has_otg = 1,
.pipe_type = usbhs_pipe_cfg,
.pipe_size = ARRAY_SIZE(usbhs_pipe_cfg),
},
},
};
static struct resource usbhs_resources[] = {
[0] = {
.start = 0xE6890000,
.end = 0xE68900e6 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(62),
.end = gic_spi(62),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device usbhs_device = {
.name = "renesas_usbhs",
.id = -1,
.dev = {
.dma_mask = NULL,
.coherent_dma_mask = 0xffffffff,
.platform_data = &usbhs_private.info,
},
.num_resources = ARRAY_SIZE(usbhs_resources),
.resource = usbhs_resources,
};
/* LCDC */
static struct fb_videomode kzm_lcdc_mode = {
.name = "WVGA Panel",
.xres = 800,
.yres = 480,
.left_margin = 220,
.right_margin = 110,
.hsync_len = 70,
.upper_margin = 20,
.lower_margin = 5,
.vsync_len = 5,
.sync = 0,
};
static struct sh_mobile_lcdc_info lcdc_info = {
.clock_source = LCDC_CLK_BUS,
.ch[0] = {
.chan = LCDC_CHAN_MAINLCD,
.fourcc = V4L2_PIX_FMT_RGB565,
.interface_type = RGB24,
.lcd_modes = &kzm_lcdc_mode,
.num_modes = 1,
.clock_divider = 5,
.flags = 0,
.panel_cfg = {
.width = 152,
.height = 91,
},
}
};
static struct resource lcdc_resources[] = {
[0] = {
.name = "LCDC",
.start = 0xfe940000,
.end = 0xfe943fff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = intcs_evt2irq(0x580),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device lcdc_device = {
.name = "sh_mobile_lcdc_fb",
.num_resources = ARRAY_SIZE(lcdc_resources),
.resource = lcdc_resources,
.dev = {
.platform_data = &lcdc_info,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
};
/* Fixed 1.8V regulator to be used by MMCIF */
static struct regulator_consumer_supply fixed1v8_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
};
/* MMCIF */
static struct resource sh_mmcif_resources[] = {
[0] = {
.name = "MMCIF",
.start = 0xe6bd0000,
.end = 0xe6bd00ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(140),
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = gic_spi(141),
.flags = IORESOURCE_IRQ,
},
};
static struct sh_mmcif_plat_data sh_mmcif_platdata = {
.ocr = MMC_VDD_165_195,
.caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
.ccs_unsupported = true,
.slave_id_tx = SHDMA_SLAVE_MMCIF_TX,
.slave_id_rx = SHDMA_SLAVE_MMCIF_RX,
};
static struct platform_device mmc_device = {
.name = "sh_mmcif",
.dev = {
.dma_mask = NULL,
.coherent_dma_mask = 0xffffffff,
.platform_data = &sh_mmcif_platdata,
},
.num_resources = ARRAY_SIZE(sh_mmcif_resources),
.resource = sh_mmcif_resources,
};
/* Fixed 3.3V regulators to be used by SDHI0 */
static struct regulator_consumer_supply vcc_sdhi0_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
};
static struct regulator_init_data vcc_sdhi0_init_data = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
.consumer_supplies = vcc_sdhi0_consumers,
};
static struct fixed_voltage_config vcc_sdhi0_info = {
.supply_name = "SDHI0 Vcc",
.microvolts = 3300000,
.gpio = 15,
.enable_high = 1,
.init_data = &vcc_sdhi0_init_data,
};
static struct platform_device vcc_sdhi0 = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
.platform_data = &vcc_sdhi0_info,
},
};
/* Fixed 3.3V regulators to be used by SDHI2 */
static struct regulator_consumer_supply vcc_sdhi2_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.2"),
};
static struct regulator_init_data vcc_sdhi2_init_data = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(vcc_sdhi2_consumers),
.consumer_supplies = vcc_sdhi2_consumers,
};
static struct fixed_voltage_config vcc_sdhi2_info = {
.supply_name = "SDHI2 Vcc",
.microvolts = 3300000,
.gpio = 14,
.enable_high = 1,
.init_data = &vcc_sdhi2_init_data,
};
static struct platform_device vcc_sdhi2 = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &vcc_sdhi2_info,
},
};
/* SDHI */
static struct sh_mobile_sdhi_info sdhi0_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
.tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
MMC_CAP_POWER_OFF_CARD,
};
static struct resource sdhi0_resources[] = {
[0] = {
.name = "SDHI0",
.start = 0xee100000,
.end = 0xee1000ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
.start = gic_spi(83),
.flags = IORESOURCE_IRQ,
},
[2] = {
.name = SH_MOBILE_SDHI_IRQ_SDCARD,
.start = gic_spi(84),
.flags = IORESOURCE_IRQ,
},
[3] = {
.name = SH_MOBILE_SDHI_IRQ_SDIO,
.start = gic_spi(85),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device sdhi0_device = {
.name = "sh_mobile_sdhi",
.num_resources = ARRAY_SIZE(sdhi0_resources),
.resource = sdhi0_resources,
.dev = {
.platform_data = &sdhi0_info,
},
};
/* Micro SD */
static struct sh_mobile_sdhi_info sdhi2_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI2_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI2_RX,
.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT |
TMIO_MMC_USE_GPIO_CD |
TMIO_MMC_WRPROTECT_DISABLE,
.tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_POWER_OFF_CARD,
.cd_gpio = 13,
};
static struct resource sdhi2_resources[] = {
[0] = {
.name = "SDHI2",
.start = 0xee140000,
.end = 0xee1400ff,
.flags = IORESOURCE_MEM,
},
[1] = {
.name = SH_MOBILE_SDHI_IRQ_CARD_DETECT,
.start = gic_spi(103),
.flags = IORESOURCE_IRQ,
},
[2] = {
.name = SH_MOBILE_SDHI_IRQ_SDCARD,
.start = gic_spi(104),
.flags = IORESOURCE_IRQ,
},
[3] = {
.name = SH_MOBILE_SDHI_IRQ_SDIO,
.start = gic_spi(105),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device sdhi2_device = {
.name = "sh_mobile_sdhi",
.id = 2,
.num_resources = ARRAY_SIZE(sdhi2_resources),
.resource = sdhi2_resources,
.dev = {
.platform_data = &sdhi2_info,
},
};
/* KEY */
#define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
static struct gpio_keys_button gpio_buttons[] = {
GPIO_KEY(KEY_BACK, GPIO_PCF8575_PORT10, "SW3"),
GPIO_KEY(KEY_RIGHT, GPIO_PCF8575_PORT11, "SW2-R"),
GPIO_KEY(KEY_LEFT, GPIO_PCF8575_PORT12, "SW2-L"),
GPIO_KEY(KEY_ENTER, GPIO_PCF8575_PORT13, "SW2-P"),
GPIO_KEY(KEY_UP, GPIO_PCF8575_PORT14, "SW2-U"),
GPIO_KEY(KEY_DOWN, GPIO_PCF8575_PORT15, "SW2-D"),
GPIO_KEY(KEY_HOME, GPIO_PCF8575_PORT16, "SW1"),
};
static struct gpio_keys_platform_data gpio_key_info = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device gpio_keys_device = {
.name = "gpio-keys",
.dev = {
.platform_data = &gpio_key_info,
},
};
/* FSI-AK4648 */
static struct sh_fsi_platform_info fsi_info = {
.port_a = {
.tx_id = SHDMA_SLAVE_FSI2A_TX,
},
};
static struct resource fsi_resources[] = {
[0] = {
.name = "FSI",
.start = 0xEC230000,
.end = 0xEC230400 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(146),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device fsi_device = {
.name = "sh_fsi2",
.id = -1,
.num_resources = ARRAY_SIZE(fsi_resources),
.resource = fsi_resources,
.dev = {
.platform_data = &fsi_info,
},
};
static struct asoc_simple_card_info fsi2_ak4648_info = {
.name = "AK4648",
.card = "FSI2A-AK4648",
.codec = "ak4642-codec.0-0012",
.platform = "sh_fsi2",
.daifmt = SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_CBM_CFM,
.cpu_dai = {
.name = "fsia-dai",
},
.codec_dai = {
.name = "ak4642-hifi",
.sysclk = 11289600,
},
};
static struct platform_device fsi_ak4648_device = {
.name = "asoc-simple-card",
.dev = {
.platform_data = &fsi2_ak4648_info,
.coherent_dma_mask = DMA_BIT_MASK(32),
.dma_mask = &fsi_ak4648_device.dev.coherent_dma_mask,
},
};
/* I2C */
/* StepDown1 is used to supply 1.315V to the CPU */
static struct regulator_init_data as3711_sd1 = {
.constraints = {
.name = "1.315V CPU",
.boot_on = 1,
.always_on = 1,
.min_uV = 1315000,
.max_uV = 1335000,
},
};
/* StepDown2 is used to supply 1.8V to the CPU and to the board */
static struct regulator_init_data as3711_sd2 = {
.constraints = {
.name = "1.8V",
.boot_on = 1,
.always_on = 1,
.min_uV = 1800000,
.max_uV = 1800000,
},
};
/*
* StepDown3 is switched in parallel with StepDown2, seems to be off,
* according to read-back pre-set register values
*/
/* StepDown4 is used to supply 1.215V to the CPU and to the board */
static struct regulator_init_data as3711_sd4 = {
.constraints = {
.name = "1.215V",
.boot_on = 1,
.always_on = 1,
.min_uV = 1215000,
.max_uV = 1235000,
},
};
/* LDO1 is unused and unconnected */
/* LDO2 is used to supply 2.8V to the CPU */
static struct regulator_init_data as3711_ldo2 = {
.constraints = {
.name = "2.8V CPU",
.boot_on = 1,
.always_on = 1,
.min_uV = 2800000,
.max_uV = 2800000,
},
};
/* LDO3 is used to supply 3.0V to the CPU */
static struct regulator_init_data as3711_ldo3 = {
.constraints = {
.name = "3.0V CPU",
.boot_on = 1,
.always_on = 1,
.min_uV = 3000000,
.max_uV = 3000000,
},
};
/* LDO4 is used to supply 2.8V to the board */
static struct regulator_init_data as3711_ldo4 = {
.constraints = {
.name = "2.8V",
.boot_on = 1,
.always_on = 1,
.min_uV = 2800000,
.max_uV = 2800000,
},
};
/* LDO5 is switched parallel to LDO4, also set to 2.8V */
static struct regulator_init_data as3711_ldo5 = {
.constraints = {
.name = "2.8V #2",
.boot_on = 1,
.always_on = 1,
.min_uV = 2800000,
.max_uV = 2800000,
},
};
/* LDO6 is unused and unconnected */
/* LDO7 is used to supply 1.15V to the CPU */
static struct regulator_init_data as3711_ldo7 = {
.constraints = {
.name = "1.15V CPU",
.boot_on = 1,
.always_on = 1,
.min_uV = 1150000,
.max_uV = 1150000,
},
};
/* LDO8 is switched parallel to LDO7, also set to 1.15V */
static struct regulator_init_data as3711_ldo8 = {
.constraints = {
.name = "1.15V CPU #2",
.boot_on = 1,
.always_on = 1,
.min_uV = 1150000,
.max_uV = 1150000,
},
};
static struct as3711_platform_data as3711_pdata = {
.regulator = {
.init_data = {
[AS3711_REGULATOR_SD_1] = &as3711_sd1,
[AS3711_REGULATOR_SD_2] = &as3711_sd2,
[AS3711_REGULATOR_SD_4] = &as3711_sd4,
[AS3711_REGULATOR_LDO_2] = &as3711_ldo2,
[AS3711_REGULATOR_LDO_3] = &as3711_ldo3,
[AS3711_REGULATOR_LDO_4] = &as3711_ldo4,
[AS3711_REGULATOR_LDO_5] = &as3711_ldo5,
[AS3711_REGULATOR_LDO_7] = &as3711_ldo7,
[AS3711_REGULATOR_LDO_8] = &as3711_ldo8,
},
},
.backlight = {
.su2_fb = "sh_mobile_lcdc_fb.0",
.su2_max_uA = 36000,
.su2_feedback = AS3711_SU2_CURR_AUTO,
.su2_fbprot = AS3711_SU2_GPIO4,
.su2_auto_curr1 = true,
.su2_auto_curr2 = true,
.su2_auto_curr3 = true,
},
};
static struct pcf857x_platform_data pcf8575_pdata = {
.gpio_base = GPIO_PCF8575_BASE,
};
static struct i2c_board_info i2c0_devices[] = {
{
I2C_BOARD_INFO("ak4648", 0x12),
},
{
I2C_BOARD_INFO("r2025sd", 0x32),
},
{
I2C_BOARD_INFO("ak8975", 0x0c),
.irq = irq_pin(28), /* IRQ28 */
},
{
I2C_BOARD_INFO("adxl34x", 0x1d),
.irq = irq_pin(26), /* IRQ26 */
},
{
I2C_BOARD_INFO("as3711", 0x40),
.irq = intcs_evt2irq(0x3300), /* IRQ24 */
.platform_data = &as3711_pdata,
},
};
static struct i2c_board_info i2c1_devices[] = {
{
I2C_BOARD_INFO("st1232-ts", 0x55),
.irq = irq_pin(8), /* IRQ8 */
},
};
static struct i2c_board_info i2c3_devices[] = {
{
I2C_BOARD_INFO("pcf8575", 0x20),
.irq = irq_pin(19), /* IRQ19 */
.platform_data = &pcf8575_pdata,
},
};
static struct platform_device *kzm_devices[] __initdata = {
&smsc_device,
&usb_host_device,
&usbhs_device,
&lcdc_device,
&mmc_device,
&vcc_sdhi0,
&vcc_sdhi2,
&sdhi0_device,
&sdhi2_device,
&gpio_keys_device,
&fsi_device,
&fsi_ak4648_device,
};
static unsigned long pin_pullup_conf[] = {
PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 0),
};
static const struct pinctrl_map kzm_pinctrl_map[] = {
/* FSIA (AK4648) */
PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
"fsia_mclk_in", "fsia"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
"fsia_sclk_in", "fsia"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
"fsia_data_in", "fsia"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_fsi2", "pfc-sh73a0",
"fsia_data_out", "fsia"),
/* I2C3 */
PIN_MAP_MUX_GROUP_DEFAULT("i2c-sh_mobile.3", "pfc-sh73a0",
"i2c3_1", "i2c3"),
/* LCD */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
"lcd_data24", "lcd"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh73a0",
"lcd_sync", "lcd"),
/* MMCIF */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
"mmc0_data8_0", "mmc0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
"mmc0_ctrl_0", "mmc0"),
PIN_MAP_CONFIGS_PIN_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
"PORT279", pin_pullup_conf),
PIN_MAP_CONFIGS_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh73a0",
"mmc0_data8_0", pin_pullup_conf),
/* SCIFA4 */
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
"scifa4_data", "scifa4"),
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.4", "pfc-sh73a0",
"scifa4_ctrl", "scifa4"),
/* SDHI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
"sdhi0_data4", "sdhi0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
"sdhi0_ctrl", "sdhi0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
"sdhi0_cd", "sdhi0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh73a0",
"sdhi0_wp", "sdhi0"),
/* SDHI2 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
"sdhi2_data4", "sdhi2"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.2", "pfc-sh73a0",
"sdhi2_ctrl", "sdhi2"),
/* SMSC */
PIN_MAP_MUX_GROUP_DEFAULT("smsc911x.0", "pfc-sh73a0",
"bsc_cs4", "bsc"),
/* USB */
PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-sh73a0",
"usb_vbus", "usb"),
};
static void __init kzm_init(void)
{
regulator_register_always_on(2, "fixed-1.8V", fixed1v8_power_consumers,
ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
regulator_register_fixed(3, dummy_supplies, ARRAY_SIZE(dummy_supplies));
pinctrl_register_mappings(kzm_pinctrl_map, ARRAY_SIZE(kzm_pinctrl_map));
sh73a0_pinmux_init();
/* SMSC */
gpio_request_one(224, GPIOF_IN, NULL); /* IRQ3 */
/* LCDC */
gpio_request_one(222, GPIOF_OUT_INIT_HIGH, NULL); /* LCDCDON */
gpio_request_one(226, GPIOF_OUT_INIT_HIGH, NULL); /* SC */
/* Touchscreen */
gpio_request_one(223, GPIOF_IN, NULL); /* IRQ8 */
#ifdef CONFIG_CACHE_L2X0
/* Shared attribute override enable, 64K*8way */
l2x0_init(IOMEM(0xf0100000), 0x00400000, 0xc20f0fff);
#endif
i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
i2c_register_board_info(1, i2c1_devices, ARRAY_SIZE(i2c1_devices));
i2c_register_board_info(3, i2c3_devices, ARRAY_SIZE(i2c3_devices));
sh73a0_add_standard_devices();
platform_add_devices(kzm_devices, ARRAY_SIZE(kzm_devices));
sh73a0_pm_init();
}
static void kzm9g_restart(enum reboot_mode mode, const char *cmd)
{
#define RESCNT2 IOMEM(0xe6188020)
/* Do soft power on reset */
writel((1 << 31), RESCNT2);
}
static const char *kzm9g_boards_compat_dt[] __initdata = {
"renesas,kzm9g",
NULL,
};
DT_MACHINE_START(KZM9G_DT, "kzm9g")
.smp = smp_ops(sh73a0_smp_ops),
.map_io = sh73a0_map_io,
.init_early = sh73a0_add_early_devices,
.nr_irqs = NR_IRQS_LEGACY,
.init_irq = sh73a0_init_irq,
.init_machine = kzm_init,
.init_late = shmobile_init_late,
.init_time = sh73a0_earlytimer_init,
.restart = kzm9g_restart,
.dt_compat = kzm9g_boards_compat_dt,
MACHINE_END
View git blame Copy permalink