1
0
Fork 0
alistair23-linux/drivers/usb
Uwe Kleine-König a82bf696aa usb: chipidea: imx: support configuring for active low oc signal
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.

This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
2018-12-11 09:13:09 +08:00
..
atm USB: atm: fix up some remaining DEVICE_ATTR() usage 2018-01-24 08:49:52 +01:00
c67x00 USB: add SPDX identifiers to all remaining Makefiles 2017-11-07 15:53:48 +01:00
chipidea usb: chipidea: imx: support configuring for active low oc signal 2018-12-11 09:13:09 +08:00
class usb: cdc-acm: add entry for Hiro (Conexant) modem 2018-11-20 12:12:06 +01:00
common usb: roles: Take care of driver module reference counting 2018-09-20 13:20:24 +02:00
core usb: hub: delay hub autosuspend if USB3 port is still link training 2018-12-05 10:12:31 +01:00
dwc2 usb: dwc2: pci: Fix an error code in probe 2018-11-14 11:07:12 +02:00
dwc3 Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid" 2018-11-26 09:05:27 +02:00
early drivers: usb: early: clean up indentation, remove extraneous tabs 2018-11-23 16:13:14 +01:00
gadget Merge 4.20-rc5 into usb-next 2018-12-03 07:53:39 +01:00
host xhci: move usb2 get port status link resume handling to its own function 2018-12-07 15:40:41 +01:00
image USB/PHY patches for 4.15-rc1 2017-11-13 21:14:07 -08:00
isp1760 usb: isp1760: remove redundant variable 'selector' 2018-07-13 15:41:56 +02:00
misc usb: appledisplay: Remove unnecessary spinlock 2018-12-05 10:42:25 +01:00
mon USB: mon: use ktime_get_real_ts64 instead of getnstimeofday64 2018-06-25 21:58:26 +08:00
mtu3 usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode 2018-12-05 10:14:06 +01:00
musb usb: musb: dsps: do not disable CPPI41 irq in driver teardown 2018-09-20 12:40:14 +02:00
phy usb: phy: ab8500: silence some uninitialized variable warnings 2018-10-18 19:44:39 +02:00
renesas_usbhs usb: renesas_usbhs: add support for R-Car E3 2018-10-02 10:48:08 +03:00
roles usb: roles: intel_xhci: Fix Unbalanced pm_runtime_enable 2018-10-09 16:13:42 +02:00
serial USB/PHY patches for 4.20-rc1 2018-10-26 08:14:13 -07:00
storage Merge 4.20-rc5 into usb-next 2018-12-03 07:53:39 +01:00
typec staging: typec: fusb302: Rename fcs,extcon-name to linux,extcon-name 2018-12-05 10:25:43 +01:00
usbip Merge branch 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs 2018-11-01 19:58:52 -07:00
wusbcore USB/PHY patches for 4.20-rc1 2018-10-26 08:14:13 -07:00
Kconfig usb: select USB_COMMON for usb role switch config 2018-04-22 15:23:37 +02:00
Makefile usb: roles: Add Intel xHCI USB role switch driver 2018-03-22 13:49:27 +01:00
README
usb-skeleton.c usb: usb-skeleton: use irqsave() in USB's complete callback 2018-06-28 19:36:06 +09:00

README

To understand all the Linux-USB framework, you'll use these resources:

    * This source code.  This is necessarily an evolving work, and
      includes kerneldoc that should help you get a current overview.
      ("make pdfdocs", and then look at "usb.pdf" for host side and
      "gadget.pdf" for peripheral side.)  Also, Documentation/usb has
      more information.

    * The USB 2.0 specification (from www.usb.org), with supplements
      such as those for USB OTG and the various device classes.
      The USB specification has a good overview chapter, and USB
      peripherals conform to the widely known "Chapter 9".

    * Chip specifications for USB controllers.  Examples include
      host controllers (on PCs, servers, and more); peripheral
      controllers (in devices with Linux firmware, like printers or
      cell phones); and hard-wired peripherals like Ethernet adapters.

    * Specifications for other protocols implemented by USB peripheral
      functions.  Some are vendor-specific; others are vendor-neutral
      but just standardized outside of the www.usb.org team.

Here is a list of what each subdirectory here is, and what is contained in
them.

core/		- This is for the core USB host code, including the
		  usbfs files and the hub class driver ("hub_wq").

host/		- This is for USB host controller drivers.  This
		  includes UHCI, OHCI, EHCI, and others that might
		  be used with more specialized "embedded" systems.

gadget/		- This is for USB peripheral controller drivers and
		  the various gadget drivers which talk to them.


Individual USB driver directories.  A new driver should be added to the
first subdirectory in the list below that it fits into.

image/		- This is for still image drivers, like scanners or
		  digital cameras.
../input/	- This is for any driver that uses the input subsystem,
		  like keyboard, mice, touchscreens, tablets, etc.
../media/	- This is for multimedia drivers, like video cameras,
		  radios, and any other drivers that talk to the v4l
		  subsystem.
../net/		- This is for network drivers.
serial/		- This is for USB to serial drivers.
storage/	- This is for USB mass-storage drivers.
class/		- This is for all USB device drivers that do not fit
		  into any of the above categories, and work for a range
		  of USB Class specified devices. 
misc/		- This is for all USB device drivers that do not fit
		  into any of the above categories.