![Rickard Strandqvist](/assets/img/avatar_default.png)
Removes some functions that are not used anywhere: omap_pm_set_max_dev_wakeup_lat() omap_pm_if_exit() omap_pm_cpu_get_freq() omap_pm_cpu_set_freq() omap_pm_cpu_get_freq_table() omap_pm_dsp_get_opp() omap_pm_dsp_set_min_opp() omap_pm_dsp_get_opp_table() omap_pm_set_min_clk_rate() omap_pm_set_max_sdma_lat() This was partially found by using a static code analysis program called cppcheck. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: Tony Lindgren <tony@atomide.com>
161 lines
5.9 KiB
C
161 lines
5.9 KiB
C
/*
|
|
* omap-pm.h - OMAP power management interface
|
|
*
|
|
* Copyright (C) 2008-2010 Texas Instruments, Inc.
|
|
* Copyright (C) 2008-2010 Nokia Corporation
|
|
* Paul Walmsley
|
|
*
|
|
* Interface developed by (in alphabetical order): Karthik Dasu, Jouni
|
|
* Högander, Tony Lindgren, Rajendra Nayak, Sakari Poussa,
|
|
* Veeramanikandan Raju, Anand Sawant, Igor Stoppa, Paul Walmsley,
|
|
* Richard Woodruff
|
|
*/
|
|
|
|
#ifndef ASM_ARM_ARCH_OMAP_OMAP_PM_H
|
|
#define ASM_ARM_ARCH_OMAP_OMAP_PM_H
|
|
|
|
#include <linux/device.h>
|
|
#include <linux/cpufreq.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/pm_opp.h>
|
|
|
|
/*
|
|
* agent_id values for use with omap_pm_set_min_bus_tput():
|
|
*
|
|
* OCP_INITIATOR_AGENT is only valid for devices that can act as
|
|
* initiators -- it represents the device's L3 interconnect
|
|
* connection. OCP_TARGET_AGENT represents the device's L4
|
|
* interconnect connection.
|
|
*/
|
|
#define OCP_TARGET_AGENT 1
|
|
#define OCP_INITIATOR_AGENT 2
|
|
|
|
/**
|
|
* omap_pm_if_early_init - OMAP PM init code called before clock fw init
|
|
* @mpu_opp_table: array ptr to struct omap_opp for MPU
|
|
* @dsp_opp_table: array ptr to struct omap_opp for DSP
|
|
* @l3_opp_table : array ptr to struct omap_opp for CORE
|
|
*
|
|
* Initialize anything that must be configured before the clock
|
|
* framework starts. The "_if_" is to avoid name collisions with the
|
|
* PM idle-loop code.
|
|
*/
|
|
int __init omap_pm_if_early_init(void);
|
|
|
|
/**
|
|
* omap_pm_if_init - OMAP PM init code called after clock fw init
|
|
*
|
|
* The main initialization code. OPP tables are passed in here. The
|
|
* "_if_" is to avoid name collisions with the PM idle-loop code.
|
|
*/
|
|
int __init omap_pm_if_init(void);
|
|
|
|
/*
|
|
* Device-driver-originated constraints (via board-*.c files, platform_data)
|
|
*/
|
|
|
|
|
|
/**
|
|
* omap_pm_set_max_mpu_wakeup_lat - set the maximum MPU wakeup latency
|
|
* @dev: struct device * requesting the constraint
|
|
* @t: maximum MPU wakeup latency in microseconds
|
|
*
|
|
* Request that the maximum interrupt latency for the MPU to be no
|
|
* greater than @t microseconds. "Interrupt latency" in this case is
|
|
* defined as the elapsed time from the occurrence of a hardware or
|
|
* timer interrupt to the time when the device driver's interrupt
|
|
* service routine has been entered by the MPU.
|
|
*
|
|
* It is intended that underlying PM code will use this information to
|
|
* determine what power state to put the MPU powerdomain into, and
|
|
* possibly the CORE powerdomain as well, since interrupt handling
|
|
* code currently runs from SDRAM. Advanced PM or board*.c code may
|
|
* also configure interrupt controller priorities, OCP bus priorities,
|
|
* CPU speed(s), etc.
|
|
*
|
|
* This function will not affect device wakeup latency, e.g., time
|
|
* elapsed from when a device driver enables a hardware device with
|
|
* clk_enable(), to when the device is ready for register access or
|
|
* other use. To control this device wakeup latency, use
|
|
* omap_pm_set_max_dev_wakeup_lat()
|
|
*
|
|
* Multiple calls to omap_pm_set_max_mpu_wakeup_lat() will replace the
|
|
* previous t value. To remove the latency target for the MPU, call
|
|
* with t = -1.
|
|
*
|
|
* XXX This constraint will be deprecated soon in favor of the more
|
|
* general omap_pm_set_max_dev_wakeup_lat()
|
|
*
|
|
* Returns -EINVAL for an invalid argument, -ERANGE if the constraint
|
|
* is not satisfiable, or 0 upon success.
|
|
*/
|
|
int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
|
|
|
|
|
|
/**
|
|
* omap_pm_set_min_bus_tput - set minimum bus throughput needed by device
|
|
* @dev: struct device * requesting the constraint
|
|
* @tbus_id: interconnect to operate on (OCP_{INITIATOR,TARGET}_AGENT)
|
|
* @r: minimum throughput (in KiB/s)
|
|
*
|
|
* Request that the minimum data throughput on the OCP interconnect
|
|
* attached to device @dev interconnect agent @tbus_id be no less
|
|
* than @r KiB/s.
|
|
*
|
|
* It is expected that the OMAP PM or bus code will use this
|
|
* information to set the interconnect clock to run at the lowest
|
|
* possible speed that satisfies all current system users. The PM or
|
|
* bus code will adjust the estimate based on its model of the bus, so
|
|
* device driver authors should attempt to specify an accurate
|
|
* quantity for their device use case, and let the PM or bus code
|
|
* overestimate the numbers as necessary to handle request/response
|
|
* latency, other competing users on the system, etc. On OMAP2/3, if
|
|
* a driver requests a minimum L4 interconnect speed constraint, the
|
|
* code will also need to add an minimum L3 interconnect speed
|
|
* constraint,
|
|
*
|
|
* Multiple calls to omap_pm_set_min_bus_tput() will replace the
|
|
* previous rate value for this device. To remove the interconnect
|
|
* throughput restriction for this device, call with r = 0.
|
|
*
|
|
* Returns -EINVAL for an invalid argument, -ERANGE if the constraint
|
|
* is not satisfiable, or 0 upon success.
|
|
*/
|
|
int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r);
|
|
|
|
|
|
/*
|
|
* CPUFreq-originated constraint
|
|
*
|
|
* In the future, this should be handled by custom OPP clocktype
|
|
* functions.
|
|
*/
|
|
|
|
|
|
/*
|
|
* Device context loss tracking
|
|
*/
|
|
|
|
/**
|
|
* omap_pm_get_dev_context_loss_count - return count of times dev has lost ctx
|
|
* @dev: struct device *
|
|
*
|
|
* This function returns the number of times that the device @dev has
|
|
* lost its internal context. This generally occurs on a powerdomain
|
|
* transition to OFF. Drivers use this as an optimization to avoid restoring
|
|
* context if the device hasn't lost it. To use, drivers should initially
|
|
* call this in their context save functions and store the result. Early in
|
|
* the driver's context restore function, the driver should call this function
|
|
* again, and compare the result to the stored counter. If they differ, the
|
|
* driver must restore device context. If the number of context losses
|
|
* exceeds the maximum positive integer, the function will wrap to 0 and
|
|
* continue counting. Returns the number of context losses for this device,
|
|
* or negative value upon error.
|
|
*/
|
|
int omap_pm_get_dev_context_loss_count(struct device *dev);
|
|
|
|
void omap_pm_enable_off_mode(void);
|
|
void omap_pm_disable_off_mode(void);
|
|
|
|
#endif
|