4f73bc4dd3
The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
50 lines
1.5 KiB
Plaintext
50 lines
1.5 KiB
Plaintext
#
|
|
# CAIF physical drivers
|
|
#
|
|
|
|
comment "CAIF transport drivers"
|
|
|
|
config CAIF_TTY
|
|
tristate "CAIF TTY transport driver"
|
|
depends on CAIF && TTY
|
|
default n
|
|
---help---
|
|
The CAIF TTY transport driver is a Line Discipline (ldisc)
|
|
identified as N_CAIF. When this ldisc is opened from user space
|
|
it will redirect the TTY's traffic into the CAIF stack.
|
|
|
|
config CAIF_SPI_SLAVE
|
|
tristate "CAIF SPI transport driver for slave interface"
|
|
depends on CAIF && HAS_DMA
|
|
default n
|
|
---help---
|
|
The CAIF Link layer SPI Protocol driver for Slave SPI interface.
|
|
This driver implements a platform driver to accommodate for a
|
|
platform specific SPI device. A sample CAIF SPI Platform device is
|
|
provided in Documentation/networking/caif/spi_porting.txt
|
|
|
|
config CAIF_SPI_SYNC
|
|
bool "Next command and length in start of frame"
|
|
depends on CAIF_SPI_SLAVE
|
|
default n
|
|
---help---
|
|
Putting the next command and length in the start of the frame can
|
|
help to synchronize to the next transfer in case of over or under-runs.
|
|
This option also needs to be enabled on the modem.
|
|
|
|
config CAIF_SHM
|
|
tristate "CAIF shared memory protocol driver"
|
|
depends on CAIF && U5500_MBOX
|
|
default n
|
|
---help---
|
|
The CAIF shared memory protocol driver for the STE UX5500 platform.
|
|
|
|
config CAIF_HSI
|
|
tristate "CAIF HSI transport driver"
|
|
depends on CAIF
|
|
default n
|
|
---help---
|
|
The caif low level driver for CAIF over HSI.
|
|
Be aware that if you enable this then you also need to
|
|
enable a low-level HSI driver.
|