alistair23-linux/drivers/gpu/drm/i915/intel_ringbuffer.h
Chris Wilson 6c067579e6 drm/i915: Split execlist priority queue into rbtree + linked list
All the requests at the same priority are executed in FIFO order. They
do not need to be stored in the rbtree themselves, as they are a simple
list within a level. If we move the requests at one priority into a list,
we can then reduce the rbtree to the set of priorities. This should keep
the height of the rbtree small, as the number of active priorities can not
exceed the number of active requests and should be typically only a few.

Currently, we have ~2k possible different priority levels, that may
increase to allow even more fine grained selection. Allocating those in
advance seems a waste (and may be impossible), so we opt for allocating
upon first use, and freeing after its requests are depleted. To avoid
the possibility of an allocation failure causing us to lose a request,
we preallocate the default priority (0) and bump any request to that
priority if we fail to allocate it the appropriate plist. Having a
request (that is ready to run, so not leading to corruption) execute
out-of-order is better than leaking the request (and its dependency
tree) entirely.

There should be a benefit to reducing execlists_dequeue() to principally
using a simple list (and reducing the frequency of both rbtree iteration
and balancing on erase) but for typical workloads, request coalescing
should be small enough that we don't notice any change. The main gain is
from improving PI calls to schedule, and the explicit list within a
level should make request unwinding simpler (we just need to insert at
the head of the list rather than the tail and not have to make the
rbtree search more complicated).

v2: Avoid use-after-free when deleting a depleted priolist

v3: Michał found the solution to handling the allocation failure
gracefully. If we disable all priority scheduling following the
allocation failure, those requests will be executed in fifo and we will
ensure that this request and its dependencies are in strict fifo (even
when it doesn't realise it is only a single list). Normal scheduling is
restored once we know the device is idle, until the next failure!
Suggested-by: Michał Wajdeczko <michal.wajdeczko@intel.com>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517121007.27224-8-chris@chris-wilson.co.uk
2017-05-17 13:38:09 +01:00

738 lines
25 KiB
C

#ifndef _INTEL_RINGBUFFER_H_
#define _INTEL_RINGBUFFER_H_
#include <linux/hashtable.h>
#include "i915_gem_batch_pool.h"
#include "i915_gem_request.h"
#include "i915_gem_timeline.h"
#include "i915_selftest.h"
#define I915_CMD_HASH_ORDER 9
/* Early gen2 devices have a cacheline of just 32 bytes, using 64 is overkill,
* but keeps the logic simple. Indeed, the whole purpose of this macro is just
* to give some inclination as to some of the magic values used in the various
* workarounds!
*/
#define CACHELINE_BYTES 64
#define CACHELINE_DWORDS (CACHELINE_BYTES / sizeof(uint32_t))
struct intel_hw_status_page {
struct i915_vma *vma;
u32 *page_addr;
u32 ggtt_offset;
};
#define I915_READ_TAIL(engine) I915_READ(RING_TAIL((engine)->mmio_base))
#define I915_WRITE_TAIL(engine, val) I915_WRITE(RING_TAIL((engine)->mmio_base), val)
#define I915_READ_START(engine) I915_READ(RING_START((engine)->mmio_base))
#define I915_WRITE_START(engine, val) I915_WRITE(RING_START((engine)->mmio_base), val)
#define I915_READ_HEAD(engine) I915_READ(RING_HEAD((engine)->mmio_base))
#define I915_WRITE_HEAD(engine, val) I915_WRITE(RING_HEAD((engine)->mmio_base), val)
#define I915_READ_CTL(engine) I915_READ(RING_CTL((engine)->mmio_base))
#define I915_WRITE_CTL(engine, val) I915_WRITE(RING_CTL((engine)->mmio_base), val)
#define I915_READ_IMR(engine) I915_READ(RING_IMR((engine)->mmio_base))
#define I915_WRITE_IMR(engine, val) I915_WRITE(RING_IMR((engine)->mmio_base), val)
#define I915_READ_MODE(engine) I915_READ(RING_MI_MODE((engine)->mmio_base))
#define I915_WRITE_MODE(engine, val) I915_WRITE(RING_MI_MODE((engine)->mmio_base), val)
/* seqno size is actually only a uint32, but since we plan to use MI_FLUSH_DW to
* do the writes, and that must have qw aligned offsets, simply pretend it's 8b.
*/
#define gen8_semaphore_seqno_size sizeof(uint64_t)
#define GEN8_SEMAPHORE_OFFSET(__from, __to) \
(((__from) * I915_NUM_ENGINES + (__to)) * gen8_semaphore_seqno_size)
#define GEN8_SIGNAL_OFFSET(__ring, to) \
(dev_priv->semaphore->node.start + \
GEN8_SEMAPHORE_OFFSET((__ring)->id, (to)))
#define GEN8_WAIT_OFFSET(__ring, from) \
(dev_priv->semaphore->node.start + \
GEN8_SEMAPHORE_OFFSET(from, (__ring)->id))
enum intel_engine_hangcheck_action {
ENGINE_IDLE = 0,
ENGINE_WAIT,
ENGINE_ACTIVE_SEQNO,
ENGINE_ACTIVE_HEAD,
ENGINE_ACTIVE_SUBUNITS,
ENGINE_WAIT_KICK,
ENGINE_DEAD,
};
static inline const char *
hangcheck_action_to_str(const enum intel_engine_hangcheck_action a)
{
switch (a) {
case ENGINE_IDLE:
return "idle";
case ENGINE_WAIT:
return "wait";
case ENGINE_ACTIVE_SEQNO:
return "active seqno";
case ENGINE_ACTIVE_HEAD:
return "active head";
case ENGINE_ACTIVE_SUBUNITS:
return "active subunits";
case ENGINE_WAIT_KICK:
return "wait kick";
case ENGINE_DEAD:
return "dead";
}
return "unknown";
}
#define I915_MAX_SLICES 3
#define I915_MAX_SUBSLICES 3
#define instdone_slice_mask(dev_priv__) \
(INTEL_GEN(dev_priv__) == 7 ? \
1 : INTEL_INFO(dev_priv__)->sseu.slice_mask)
#define instdone_subslice_mask(dev_priv__) \
(INTEL_GEN(dev_priv__) == 7 ? \
1 : INTEL_INFO(dev_priv__)->sseu.subslice_mask)
#define for_each_instdone_slice_subslice(dev_priv__, slice__, subslice__) \
for ((slice__) = 0, (subslice__) = 0; \
(slice__) < I915_MAX_SLICES; \
(subslice__) = ((subslice__) + 1) < I915_MAX_SUBSLICES ? (subslice__) + 1 : 0, \
(slice__) += ((subslice__) == 0)) \
for_each_if((BIT(slice__) & instdone_slice_mask(dev_priv__)) && \
(BIT(subslice__) & instdone_subslice_mask(dev_priv__)))
struct intel_instdone {
u32 instdone;
/* The following exist only in the RCS engine */
u32 slice_common;
u32 sampler[I915_MAX_SLICES][I915_MAX_SUBSLICES];
u32 row[I915_MAX_SLICES][I915_MAX_SUBSLICES];
};
struct intel_engine_hangcheck {
u64 acthd;
u32 seqno;
enum intel_engine_hangcheck_action action;
unsigned long action_timestamp;
int deadlock;
struct intel_instdone instdone;
bool stalled;
};
struct intel_ring {
struct i915_vma *vma;
void *vaddr;
struct list_head request_list;
u32 head;
u32 tail;
u32 emit;
u32 space;
u32 size;
u32 effective_size;
};
struct i915_gem_context;
struct drm_i915_reg_table;
/*
* we use a single page to load ctx workarounds so all of these
* values are referred in terms of dwords
*
* struct i915_wa_ctx_bb:
* offset: specifies batch starting position, also helpful in case
* if we want to have multiple batches at different offsets based on
* some criteria. It is not a requirement at the moment but provides
* an option for future use.
* size: size of the batch in DWORDS
*/
struct i915_ctx_workarounds {
struct i915_wa_ctx_bb {
u32 offset;
u32 size;
} indirect_ctx, per_ctx;
struct i915_vma *vma;
};
struct drm_i915_gem_request;
struct intel_render_state;
/*
* Engine IDs definitions.
* Keep instances of the same type engine together.
*/
enum intel_engine_id {
RCS = 0,
BCS,
VCS,
VCS2,
#define _VCS(n) (VCS + (n))
VECS
};
struct i915_priolist {
struct rb_node node;
struct list_head requests;
int priority;
};
#define INTEL_ENGINE_CS_MAX_NAME 8
struct intel_engine_cs {
struct drm_i915_private *i915;
char name[INTEL_ENGINE_CS_MAX_NAME];
enum intel_engine_id id;
unsigned int uabi_id;
unsigned int hw_id;
unsigned int guc_id;
u8 class;
u8 instance;
u32 context_size;
u32 mmio_base;
unsigned int irq_shift;
struct intel_ring *buffer;
struct intel_timeline *timeline;
struct intel_render_state *render_state;
atomic_t irq_count;
unsigned long irq_posted;
#define ENGINE_IRQ_BREADCRUMB 0
#define ENGINE_IRQ_EXECLIST 1
/* Rather than have every client wait upon all user interrupts,
* with the herd waking after every interrupt and each doing the
* heavyweight seqno dance, we delegate the task (of being the
* bottom-half of the user interrupt) to the first client. After
* every interrupt, we wake up one client, who does the heavyweight
* coherent seqno read and either goes back to sleep (if incomplete),
* or wakes up all the completed clients in parallel, before then
* transferring the bottom-half status to the next client in the queue.
*
* Compared to walking the entire list of waiters in a single dedicated
* bottom-half, we reduce the latency of the first waiter by avoiding
* a context switch, but incur additional coherent seqno reads when
* following the chain of request breadcrumbs. Since it is most likely
* that we have a single client waiting on each seqno, then reducing
* the overhead of waking that client is much preferred.
*/
struct intel_breadcrumbs {
spinlock_t irq_lock; /* protects irq_*; irqsafe */
struct intel_wait *irq_wait; /* oldest waiter by retirement */
spinlock_t rb_lock; /* protects the rb and wraps irq_lock */
struct rb_root waiters; /* sorted by retirement, priority */
struct rb_root signals; /* sorted by retirement */
struct task_struct *signaler; /* used for fence signalling */
struct drm_i915_gem_request __rcu *first_signal;
struct timer_list fake_irq; /* used after a missed interrupt */
struct timer_list hangcheck; /* detect missed interrupts */
unsigned int hangcheck_interrupts;
bool irq_armed : 1;
bool irq_enabled : 1;
I915_SELFTEST_DECLARE(bool mock : 1);
} breadcrumbs;
/*
* A pool of objects to use as shadow copies of client batch buffers
* when the command parser is enabled. Prevents the client from
* modifying the batch contents after software parsing.
*/
struct i915_gem_batch_pool batch_pool;
struct intel_hw_status_page status_page;
struct i915_ctx_workarounds wa_ctx;
struct i915_vma *scratch;
u32 irq_keep_mask; /* always keep these interrupts */
u32 irq_enable_mask; /* bitmask to enable ring interrupt */
void (*irq_enable)(struct intel_engine_cs *engine);
void (*irq_disable)(struct intel_engine_cs *engine);
int (*init_hw)(struct intel_engine_cs *engine);
void (*reset_hw)(struct intel_engine_cs *engine,
struct drm_i915_gem_request *req);
void (*set_default_submission)(struct intel_engine_cs *engine);
struct intel_ring *(*context_pin)(struct intel_engine_cs *engine,
struct i915_gem_context *ctx);
void (*context_unpin)(struct intel_engine_cs *engine,
struct i915_gem_context *ctx);
int (*request_alloc)(struct drm_i915_gem_request *req);
int (*init_context)(struct drm_i915_gem_request *req);
int (*emit_flush)(struct drm_i915_gem_request *request,
u32 mode);
#define EMIT_INVALIDATE BIT(0)
#define EMIT_FLUSH BIT(1)
#define EMIT_BARRIER (EMIT_INVALIDATE | EMIT_FLUSH)
int (*emit_bb_start)(struct drm_i915_gem_request *req,
u64 offset, u32 length,
unsigned int dispatch_flags);
#define I915_DISPATCH_SECURE BIT(0)
#define I915_DISPATCH_PINNED BIT(1)
#define I915_DISPATCH_RS BIT(2)
void (*emit_breadcrumb)(struct drm_i915_gem_request *req,
u32 *cs);
int emit_breadcrumb_sz;
/* Pass the request to the hardware queue (e.g. directly into
* the legacy ringbuffer or to the end of an execlist).
*
* This is called from an atomic context with irqs disabled; must
* be irq safe.
*/
void (*submit_request)(struct drm_i915_gem_request *req);
/* Call when the priority on a request has changed and it and its
* dependencies may need rescheduling. Note the request itself may
* not be ready to run!
*
* Called under the struct_mutex.
*/
void (*schedule)(struct drm_i915_gem_request *request,
int priority);
/* Some chipsets are not quite as coherent as advertised and need
* an expensive kick to force a true read of the up-to-date seqno.
* However, the up-to-date seqno is not always required and the last
* seen value is good enough. Note that the seqno will always be
* monotonic, even if not coherent.
*/
void (*irq_seqno_barrier)(struct intel_engine_cs *engine);
void (*cleanup)(struct intel_engine_cs *engine);
/* GEN8 signal/wait table - never trust comments!
* signal to signal to signal to signal to signal to
* RCS VCS BCS VECS VCS2
* --------------------------------------------------------------------
* RCS | NOP (0x00) | VCS (0x08) | BCS (0x10) | VECS (0x18) | VCS2 (0x20) |
* |-------------------------------------------------------------------
* VCS | RCS (0x28) | NOP (0x30) | BCS (0x38) | VECS (0x40) | VCS2 (0x48) |
* |-------------------------------------------------------------------
* BCS | RCS (0x50) | VCS (0x58) | NOP (0x60) | VECS (0x68) | VCS2 (0x70) |
* |-------------------------------------------------------------------
* VECS | RCS (0x78) | VCS (0x80) | BCS (0x88) | NOP (0x90) | VCS2 (0x98) |
* |-------------------------------------------------------------------
* VCS2 | RCS (0xa0) | VCS (0xa8) | BCS (0xb0) | VECS (0xb8) | NOP (0xc0) |
* |-------------------------------------------------------------------
*
* Generalization:
* f(x, y) := (x->id * NUM_RINGS * seqno_size) + (seqno_size * y->id)
* ie. transpose of g(x, y)
*
* sync from sync from sync from sync from sync from
* RCS VCS BCS VECS VCS2
* --------------------------------------------------------------------
* RCS | NOP (0x00) | VCS (0x28) | BCS (0x50) | VECS (0x78) | VCS2 (0xa0) |
* |-------------------------------------------------------------------
* VCS | RCS (0x08) | NOP (0x30) | BCS (0x58) | VECS (0x80) | VCS2 (0xa8) |
* |-------------------------------------------------------------------
* BCS | RCS (0x10) | VCS (0x38) | NOP (0x60) | VECS (0x88) | VCS2 (0xb0) |
* |-------------------------------------------------------------------
* VECS | RCS (0x18) | VCS (0x40) | BCS (0x68) | NOP (0x90) | VCS2 (0xb8) |
* |-------------------------------------------------------------------
* VCS2 | RCS (0x20) | VCS (0x48) | BCS (0x70) | VECS (0x98) | NOP (0xc0) |
* |-------------------------------------------------------------------
*
* Generalization:
* g(x, y) := (y->id * NUM_RINGS * seqno_size) + (seqno_size * x->id)
* ie. transpose of f(x, y)
*/
struct {
union {
#define GEN6_SEMAPHORE_LAST VECS_HW
#define GEN6_NUM_SEMAPHORES (GEN6_SEMAPHORE_LAST + 1)
#define GEN6_SEMAPHORES_MASK GENMASK(GEN6_SEMAPHORE_LAST, 0)
struct {
/* our mbox written by others */
u32 wait[GEN6_NUM_SEMAPHORES];
/* mboxes this ring signals to */
i915_reg_t signal[GEN6_NUM_SEMAPHORES];
} mbox;
u64 signal_ggtt[I915_NUM_ENGINES];
};
/* AKA wait() */
int (*sync_to)(struct drm_i915_gem_request *req,
struct drm_i915_gem_request *signal);
u32 *(*signal)(struct drm_i915_gem_request *req, u32 *cs);
} semaphore;
/* Execlists */
struct tasklet_struct irq_tasklet;
struct i915_priolist default_priolist;
bool no_priolist;
struct execlist_port {
struct drm_i915_gem_request *request_count;
#define EXECLIST_COUNT_BITS 2
#define port_request(p) ptr_mask_bits((p)->request_count, EXECLIST_COUNT_BITS)
#define port_count(p) ptr_unmask_bits((p)->request_count, EXECLIST_COUNT_BITS)
#define port_pack(rq, count) ptr_pack_bits(rq, count, EXECLIST_COUNT_BITS)
#define port_unpack(p, count) ptr_unpack_bits((p)->request_count, count, EXECLIST_COUNT_BITS)
#define port_set(p, packed) ((p)->request_count = (packed))
#define port_isset(p) ((p)->request_count)
#define port_index(p, e) ((p) - (e)->execlist_port)
GEM_DEBUG_DECL(u32 context_id);
} execlist_port[2];
struct rb_root execlist_queue;
struct rb_node *execlist_first;
unsigned int fw_domains;
/* Contexts are pinned whilst they are active on the GPU. The last
* context executed remains active whilst the GPU is idle - the
* switch away and write to the context object only occurs on the
* next execution. Contexts are only unpinned on retirement of the
* following request ensuring that we can always write to the object
* on the context switch even after idling. Across suspend, we switch
* to the kernel context and trash it as the save may not happen
* before the hardware is powered down.
*/
struct i915_gem_context *last_retired_context;
/* We track the current MI_SET_CONTEXT in order to eliminate
* redudant context switches. This presumes that requests are not
* reordered! Or when they are the tracking is updated along with
* the emission of individual requests into the legacy command
* stream (ring).
*/
struct i915_gem_context *legacy_active_context;
/* status_notifier: list of callbacks for context-switch changes */
struct atomic_notifier_head context_status_notifier;
struct intel_engine_hangcheck hangcheck;
bool needs_cmd_parser;
/*
* Table of commands the command parser needs to know about
* for this engine.
*/
DECLARE_HASHTABLE(cmd_hash, I915_CMD_HASH_ORDER);
/*
* Table of registers allowed in commands that read/write registers.
*/
const struct drm_i915_reg_table *reg_tables;
int reg_table_count;
/*
* Returns the bitmask for the length field of the specified command.
* Return 0 for an unrecognized/invalid command.
*
* If the command parser finds an entry for a command in the engine's
* cmd_tables, it gets the command's length based on the table entry.
* If not, it calls this function to determine the per-engine length
* field encoding for the command (i.e. different opcode ranges use
* certain bits to encode the command length in the header).
*/
u32 (*get_cmd_length_mask)(u32 cmd_header);
};
static inline unsigned int
intel_engine_flag(const struct intel_engine_cs *engine)
{
return BIT(engine->id);
}
static inline u32
intel_read_status_page(struct intel_engine_cs *engine, int reg)
{
/* Ensure that the compiler doesn't optimize away the load. */
return READ_ONCE(engine->status_page.page_addr[reg]);
}
static inline void
intel_write_status_page(struct intel_engine_cs *engine, int reg, u32 value)
{
/* Writing into the status page should be done sparingly. Since
* we do when we are uncertain of the device state, we take a bit
* of extra paranoia to try and ensure that the HWS takes the value
* we give and that it doesn't end up trapped inside the CPU!
*/
if (static_cpu_has(X86_FEATURE_CLFLUSH)) {
mb();
clflush(&engine->status_page.page_addr[reg]);
engine->status_page.page_addr[reg] = value;
clflush(&engine->status_page.page_addr[reg]);
mb();
} else {
WRITE_ONCE(engine->status_page.page_addr[reg], value);
}
}
/*
* Reads a dword out of the status page, which is written to from the command
* queue by automatic updates, MI_REPORT_HEAD, MI_STORE_DATA_INDEX, or
* MI_STORE_DATA_IMM.
*
* The following dwords have a reserved meaning:
* 0x00: ISR copy, updated when an ISR bit not set in the HWSTAM changes.
* 0x04: ring 0 head pointer
* 0x05: ring 1 head pointer (915-class)
* 0x06: ring 2 head pointer (915-class)
* 0x10-0x1b: Context status DWords (GM45)
* 0x1f: Last written status offset. (GM45)
* 0x20-0x2f: Reserved (Gen6+)
*
* The area from dword 0x30 to 0x3ff is available for driver usage.
*/
#define I915_GEM_HWS_INDEX 0x30
#define I915_GEM_HWS_INDEX_ADDR (I915_GEM_HWS_INDEX << MI_STORE_DWORD_INDEX_SHIFT)
#define I915_GEM_HWS_SCRATCH_INDEX 0x40
#define I915_GEM_HWS_SCRATCH_ADDR (I915_GEM_HWS_SCRATCH_INDEX << MI_STORE_DWORD_INDEX_SHIFT)
struct intel_ring *
intel_engine_create_ring(struct intel_engine_cs *engine, int size);
int intel_ring_pin(struct intel_ring *ring,
struct drm_i915_private *i915,
unsigned int offset_bias);
void intel_ring_reset(struct intel_ring *ring, u32 tail);
unsigned int intel_ring_update_space(struct intel_ring *ring);
void intel_ring_unpin(struct intel_ring *ring);
void intel_ring_free(struct intel_ring *ring);
void intel_engine_stop(struct intel_engine_cs *engine);
void intel_engine_cleanup(struct intel_engine_cs *engine);
void intel_legacy_submission_resume(struct drm_i915_private *dev_priv);
int __must_check intel_ring_cacheline_align(struct drm_i915_gem_request *req);
u32 __must_check *intel_ring_begin(struct drm_i915_gem_request *req,
unsigned int n);
static inline void
intel_ring_advance(struct drm_i915_gem_request *req, u32 *cs)
{
/* Dummy function.
*
* This serves as a placeholder in the code so that the reader
* can compare against the preceding intel_ring_begin() and
* check that the number of dwords emitted matches the space
* reserved for the command packet (i.e. the value passed to
* intel_ring_begin()).
*/
GEM_BUG_ON((req->ring->vaddr + req->ring->emit) != cs);
}
static inline u32
intel_ring_wrap(const struct intel_ring *ring, u32 pos)
{
return pos & (ring->size - 1);
}
static inline u32
intel_ring_offset(const struct drm_i915_gem_request *req, void *addr)
{
/* Don't write ring->size (equivalent to 0) as that hangs some GPUs. */
u32 offset = addr - req->ring->vaddr;
GEM_BUG_ON(offset > req->ring->size);
return intel_ring_wrap(req->ring, offset);
}
static inline void
assert_ring_tail_valid(const struct intel_ring *ring, unsigned int tail)
{
/* We could combine these into a single tail operation, but keeping
* them as seperate tests will help identify the cause should one
* ever fire.
*/
GEM_BUG_ON(!IS_ALIGNED(tail, 8));
GEM_BUG_ON(tail >= ring->size);
/*
* "Ring Buffer Use"
* Gen2 BSpec "1. Programming Environment" / 1.4.4.6
* Gen3 BSpec "1c Memory Interface Functions" / 2.3.4.5
* Gen4+ BSpec "1c Memory Interface and Command Stream" / 5.3.4.5
* "If the Ring Buffer Head Pointer and the Tail Pointer are on the
* same cacheline, the Head Pointer must not be greater than the Tail
* Pointer."
*
* We use ring->head as the last known location of the actual RING_HEAD,
* it may have advanced but in the worst case it is equally the same
* as ring->head and so we should never program RING_TAIL to advance
* into the same cacheline as ring->head.
*/
#define cacheline(a) round_down(a, CACHELINE_BYTES)
GEM_BUG_ON(cacheline(tail) == cacheline(ring->head) &&
tail < ring->head);
#undef cacheline
}
static inline unsigned int
intel_ring_set_tail(struct intel_ring *ring, unsigned int tail)
{
/* Whilst writes to the tail are strictly order, there is no
* serialisation between readers and the writers. The tail may be
* read by i915_gem_request_retire() just as it is being updated
* by execlists, as although the breadcrumb is complete, the context
* switch hasn't been seen.
*/
assert_ring_tail_valid(ring, tail);
ring->tail = tail;
return tail;
}
void intel_engine_init_global_seqno(struct intel_engine_cs *engine, u32 seqno);
void intel_engine_setup_common(struct intel_engine_cs *engine);
int intel_engine_init_common(struct intel_engine_cs *engine);
int intel_engine_create_scratch(struct intel_engine_cs *engine, int size);
void intel_engine_cleanup_common(struct intel_engine_cs *engine);
int intel_init_render_ring_buffer(struct intel_engine_cs *engine);
int intel_init_bsd_ring_buffer(struct intel_engine_cs *engine);
int intel_init_blt_ring_buffer(struct intel_engine_cs *engine);
int intel_init_vebox_ring_buffer(struct intel_engine_cs *engine);
u64 intel_engine_get_active_head(struct intel_engine_cs *engine);
u64 intel_engine_get_last_batch_head(struct intel_engine_cs *engine);
static inline u32 intel_engine_get_seqno(struct intel_engine_cs *engine)
{
return intel_read_status_page(engine, I915_GEM_HWS_INDEX);
}
static inline u32 intel_engine_last_submit(struct intel_engine_cs *engine)
{
/* We are only peeking at the tail of the submit queue (and not the
* queue itself) in order to gain a hint as to the current active
* state of the engine. Callers are not expected to be taking
* engine->timeline->lock, nor are they expected to be concerned
* wtih serialising this hint with anything, so document it as
* a hint and nothing more.
*/
return READ_ONCE(engine->timeline->seqno);
}
int init_workarounds_ring(struct intel_engine_cs *engine);
int intel_ring_workarounds_emit(struct drm_i915_gem_request *req);
void intel_engine_get_instdone(struct intel_engine_cs *engine,
struct intel_instdone *instdone);
/*
* Arbitrary size for largest possible 'add request' sequence. The code paths
* are complex and variable. Empirical measurement shows that the worst case
* is BDW at 192 bytes (6 + 6 + 36 dwords), then ILK at 136 bytes. However,
* we need to allocate double the largest single packet within that emission
* to account for tail wraparound (so 6 + 6 + 72 dwords for BDW).
*/
#define MIN_SPACE_FOR_ADD_REQUEST 336
static inline u32 intel_hws_seqno_address(struct intel_engine_cs *engine)
{
return engine->status_page.ggtt_offset + I915_GEM_HWS_INDEX_ADDR;
}
/* intel_breadcrumbs.c -- user interrupt bottom-half for waiters */
int intel_engine_init_breadcrumbs(struct intel_engine_cs *engine);
static inline void intel_wait_init(struct intel_wait *wait,
struct drm_i915_gem_request *rq)
{
wait->tsk = current;
wait->request = rq;
}
static inline void intel_wait_init_for_seqno(struct intel_wait *wait, u32 seqno)
{
wait->tsk = current;
wait->seqno = seqno;
}
static inline bool intel_wait_has_seqno(const struct intel_wait *wait)
{
return wait->seqno;
}
static inline bool
intel_wait_update_seqno(struct intel_wait *wait, u32 seqno)
{
wait->seqno = seqno;
return intel_wait_has_seqno(wait);
}
static inline bool
intel_wait_update_request(struct intel_wait *wait,
const struct drm_i915_gem_request *rq)
{
return intel_wait_update_seqno(wait, i915_gem_request_global_seqno(rq));
}
static inline bool
intel_wait_check_seqno(const struct intel_wait *wait, u32 seqno)
{
return wait->seqno == seqno;
}
static inline bool
intel_wait_check_request(const struct intel_wait *wait,
const struct drm_i915_gem_request *rq)
{
return intel_wait_check_seqno(wait, i915_gem_request_global_seqno(rq));
}
static inline bool intel_wait_complete(const struct intel_wait *wait)
{
return RB_EMPTY_NODE(&wait->node);
}
bool intel_engine_add_wait(struct intel_engine_cs *engine,
struct intel_wait *wait);
void intel_engine_remove_wait(struct intel_engine_cs *engine,
struct intel_wait *wait);
void intel_engine_enable_signaling(struct drm_i915_gem_request *request,
bool wakeup);
void intel_engine_cancel_signaling(struct drm_i915_gem_request *request);
static inline bool intel_engine_has_waiter(const struct intel_engine_cs *engine)
{
return READ_ONCE(engine->breadcrumbs.irq_wait);
}
unsigned int intel_engine_wakeup(struct intel_engine_cs *engine);
#define ENGINE_WAKEUP_WAITER BIT(0)
#define ENGINE_WAKEUP_ASLEEP BIT(1)
void __intel_engine_disarm_breadcrumbs(struct intel_engine_cs *engine);
void intel_engine_disarm_breadcrumbs(struct intel_engine_cs *engine);
void intel_engine_reset_breadcrumbs(struct intel_engine_cs *engine);
void intel_engine_fini_breadcrumbs(struct intel_engine_cs *engine);
bool intel_breadcrumbs_busy(struct intel_engine_cs *engine);
static inline u32 *gen8_emit_pipe_control(u32 *batch, u32 flags, u32 offset)
{
memset(batch, 0, 6 * sizeof(u32));
batch[0] = GFX_OP_PIPE_CONTROL(6);
batch[1] = flags;
batch[2] = offset;
return batch + 6;
}
bool intel_engine_is_idle(struct intel_engine_cs *engine);
bool intel_engines_are_idle(struct drm_i915_private *dev_priv);
void intel_engines_mark_idle(struct drm_i915_private *i915);
void intel_engines_reset_default_submission(struct drm_i915_private *i915);
#endif /* _INTEL_RINGBUFFER_H_ */