d2d13ed013
Device tree binding documentation for Broadcom NS2 IOMUX Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
103 lines
3.1 KiB
Plaintext
103 lines
3.1 KiB
Plaintext
Broadcom Northstar2 IOMUX Controller
|
|
|
|
The Northstar2 IOMUX controller supports group based mux configuration. There
|
|
are some individual pins that support modifying the pinconf parameters.
|
|
|
|
Required properties:
|
|
|
|
- compatible:
|
|
Must be "brcm,ns2-pinmux"
|
|
|
|
- reg:
|
|
Define the base and range of the I/O address space that contains the
|
|
Northstar2 IOMUX and pin configuration registers.
|
|
|
|
Properties in sub nodes:
|
|
|
|
- function:
|
|
The mux function to select
|
|
|
|
- groups:
|
|
The list of groups to select with a given function
|
|
|
|
- pins:
|
|
List of pin names to change configuration
|
|
|
|
The generic properties bias-disable, bias-pull-down, bias-pull-up,
|
|
drive-strength, slew-rate, input-enable, input-disable are supported
|
|
for some individual pins listed at the end.
|
|
|
|
For more details, refer to
|
|
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
|
|
|
|
For example:
|
|
|
|
pinctrl: pinctrl@6501d130 {
|
|
compatible = "brcm,ns2-pinmux";
|
|
reg = <0x6501d130 0x08>,
|
|
<0x660a0028 0x04>,
|
|
<0x660009b0 0x40>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&nand_sel &uart3_rx &sdio0_d4>;
|
|
|
|
/* Select nand function */
|
|
nand_sel: nand_sel {
|
|
function = "nand";
|
|
groups = "nand_grp";
|
|
};
|
|
|
|
/* Pull up the uart3 rx pin */
|
|
uart3_rx: uart3_rx {
|
|
pins = "uart3_sin";
|
|
bias-pull-up;
|
|
};
|
|
|
|
/* Set the drive strength of sdio d4 pin */
|
|
sdio0_d4: sdio0_d4 {
|
|
pins = "sdio0_data4";
|
|
drive-strength = <8>;
|
|
};
|
|
};
|
|
|
|
List of supported functions and groups in Northstar2:
|
|
|
|
"nand": "nand_grp"
|
|
|
|
"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp",
|
|
"nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp",
|
|
"nor_addr_12_15_grp"
|
|
|
|
"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp",
|
|
"gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp",
|
|
"gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp",
|
|
"gpio_28_29_grp", "gpio_30_31_grp"
|
|
|
|
"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp",
|
|
"pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp"
|
|
|
|
"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp"
|
|
|
|
"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp",
|
|
"uart1_rts_cts_grp", "uart1_in_out_grp"
|
|
|
|
"uart2": "uart2_rts_cts_grp"
|
|
|
|
"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp"
|
|
|
|
|
|
List of pins that support pinconf parameters:
|
|
|
|
"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout",
|
|
"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck",
|
|
"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7",
|
|
"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4",
|
|
"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1",
|
|
"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk",
|
|
"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1",
|
|
"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk",
|
|
"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc",
|
|
"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent",
|
|
"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc",
|
|
"usb2_overcurrent", "sata_led1", "sata_led0"
|