redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity
alistair23-linux/drivers/pinctrl/Kconfig
Simon Arlott e1b2dc70cd pinctrl: add bcm2835 driver 
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.

Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.

Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
  datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
  implemented are driven by the board, not the GPIO HW block, so don't
  really make sense of a HW block binding, were in general incomplete
  (since they could only know about the few pins hard-coded into the
  Raspberry Pi B board design and not the uncommitted GPIOS), and are
  better represented simply by not writing incorrect data into pin
  configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
  glitches; defer this to gpio_set_direction(). Consequently, removed
  empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
  IRQ handler, thus fixing an issue where the code was indexing into
  enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
  spin_lock_irqsave() and so guarantees it doesn't run concurrently
  with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
  bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
  decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
  directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
  core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
  descriptive.
* Simplified remove(); removed call to non-existent
  pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
  base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-10-01 08:05:22 +02:00

174 lines
3.2 KiB
Plaintext
Raw Blame History

#
# PINCTRL infrastructure and drivers
#
config PINCTRL
bool
if PINCTRL
menu "Pin controllers"
depends on PINCTRL
config PINMUX
bool "Support pin multiplexing controllers"
config PINCONF
bool "Support pin configuration controllers"
config GENERIC_PINCONF
bool
select PINCONF
config DEBUG_PINCTRL
bool "Debug PINCTRL calls"
depends on DEBUG_KERNEL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
config PINCTRL_BCM2835
bool
select PINMUX
select PINCONF
config PINCTRL_IMX
bool
select PINMUX
select PINCONF
config PINCTRL_IMX35
bool "IMX35 pinctrl driver"
depends on OF
depends on SOC_IMX35
select PINCTRL_IMX
help
Say Y here to enable the imx35 pinctrl driver
config PINCTRL_IMX51
bool "IMX51 pinctrl driver"
depends on OF
depends on SOC_IMX51
select PINCTRL_IMX
help
Say Y here to enable the imx51 pinctrl driver
config PINCTRL_IMX53
bool "IMX53 pinctrl driver"
depends on OF
depends on SOC_IMX53
select PINCTRL_IMX
help
Say Y here to enable the imx53 pinctrl driver
config PINCTRL_IMX6Q
bool "IMX6Q pinctrl driver"
depends on OF
depends on SOC_IMX6Q
select PINCTRL_IMX
help
Say Y here to enable the imx6q pinctrl driver
config PINCTRL_PXA3xx
bool
select PINMUX
config PINCTRL_MMP2
bool "MMP2 pin controller driver"
depends on ARCH_MMP
select PINCTRL_PXA3xx
select PINCONF
config PINCTRL_MXS
bool
config PINCTRL_IMX23
bool
select PINMUX
select PINCONF
select PINCTRL_MXS
config PINCTRL_IMX28
bool
select PINMUX
select PINCONF
select PINCTRL_MXS
config PINCTRL_NOMADIK
bool "Nomadik pin controller driver"
depends on ARCH_U8500 || ARCH_NOMADIK
select PINMUX
select PINCONF
config PINCTRL_STN8815
bool "STN8815 pin controller driver"
depends on PINCTRL_NOMADIK && ARCH_NOMADIK
config PINCTRL_DB8500
bool "DB8500 pin controller driver"
depends on PINCTRL_NOMADIK && ARCH_U8500
config PINCTRL_DB8540
bool "DB8540 pin controller driver"
depends on PINCTRL_NOMADIK && ARCH_U8500
config PINCTRL_PXA168
bool "PXA168 pin controller driver"
depends on ARCH_MMP
select PINCTRL_PXA3xx
select PINCONF
config PINCTRL_PXA910
bool "PXA910 pin controller driver"
depends on ARCH_MMP
select PINCTRL_PXA3xx
select PINCONF
config PINCTRL_SINGLE
tristate "One-register-per-pin type device tree based pinctrl driver"
depends on OF
select PINMUX
select PINCONF
help
This selects the device tree based generic pinctrl driver.
config PINCTRL_SIRF
bool "CSR SiRFprimaII pin controller driver"
depends on ARCH_PRIMA2
select PINMUX
config PINCTRL_TEGRA
bool
config PINCTRL_TEGRA20
bool
select PINMUX
select PINCONF
select PINCTRL_TEGRA
config PINCTRL_TEGRA30
bool
select PINMUX
select PINCONF
select PINCTRL_TEGRA
config PINCTRL_U300
bool "U300 pin controller driver"
depends on ARCH_U300
select PINMUX
select GENERIC_PINCONF
config PINCTRL_COH901
bool "ST-Ericsson U300 COH 901 335/571 GPIO"
depends on GPIOLIB && ARCH_U300 && PINCTRL_U300
help
Say yes here to support GPIO interface on ST-Ericsson U300.
The names of the two IP block variants supported are
COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
ports of 8 GPIO pins each.
source "drivers/pinctrl/spear/Kconfig"
endmenu
endif
View git blame Copy permalink