1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
186 lines
3.3 KiB
Plaintext
186 lines
3.3 KiB
Plaintext
/*
|
|
* animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards
|
|
*
|
|
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
*
|
|
* Licensed under GPLv2 only.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "at91sam9260.dtsi"
|
|
|
|
/ {
|
|
model = "Somfy Animeo IP";
|
|
compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9";
|
|
|
|
aliases {
|
|
serial0 = &usart1;
|
|
serial1 = &usart2;
|
|
serial2 = &usart0;
|
|
serial3 = &dbgu;
|
|
serial4 = &usart3;
|
|
serial5 = &uart0;
|
|
serial6 = &uart1;
|
|
};
|
|
|
|
chosen {
|
|
linux,stdout-path = &usart2;
|
|
};
|
|
|
|
memory {
|
|
reg = <0x20000000 0x4000000>;
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <18432000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
usart0: serial@fffb0000 {
|
|
pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>;
|
|
linux,rs485-enabled-at-boot-time;
|
|
status = "okay";
|
|
};
|
|
|
|
usart1: serial@fffb4000 {
|
|
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>;
|
|
linux,rs485-enabled-at-boot-time;
|
|
status = "okay";
|
|
};
|
|
|
|
usart2: serial@fffb8000 {
|
|
pinctrl-0 = <&pinctrl_usart2>;
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@fffc4000 {
|
|
pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>;
|
|
phy-mode = "mii";
|
|
status = "okay";
|
|
};
|
|
|
|
mmc0: mmc@fffa8000 {
|
|
pinctrl-0 = <&pinctrl_mmc0_clk
|
|
&pinctrl_mmc0_slot1_cmd_dat0
|
|
&pinctrl_mmc0_slot1_dat1_3>;
|
|
status = "okay";
|
|
|
|
slot@1 {
|
|
reg = <1>;
|
|
bus-width = <4>;
|
|
};
|
|
};
|
|
|
|
watchdog@fffffd40 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
status = "okay";
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
|
|
pinctrl-names = "default";
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
barebox@0 {
|
|
label = "barebox";
|
|
reg = <0x0 0x58000>;
|
|
};
|
|
|
|
u_boot_env@58000 {
|
|
label = "u_boot_env";
|
|
reg = <0x58000 0x8000>;
|
|
};
|
|
|
|
ubi@60000 {
|
|
label = "ubi";
|
|
reg = <0x60000 0x1FA0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
usb0: ohci@500000 {
|
|
num-ports = <2>;
|
|
atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power_green {
|
|
label = "power_green";
|
|
gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
power_red {
|
|
label = "power_red";
|
|
gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
tx_green {
|
|
label = "tx_green";
|
|
gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
tx_red {
|
|
label = "tx_red";
|
|
gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
keyswitch_in {
|
|
label = "keyswitch_in";
|
|
gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <28>;
|
|
wakeup-source;
|
|
};
|
|
|
|
error_in {
|
|
label = "error_in";
|
|
gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <29>;
|
|
wakeup-source;
|
|
};
|
|
|
|
btn {
|
|
label = "btn";
|
|
gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <31>;
|
|
wakeup-source;
|
|
};
|
|
};
|
|
};
|