8b1750de6a
PHYs have an address on the mdio bus. So the unit name should contain an address. This is complicated in that some .dtsi files contain the node, but the reg is set in the .dts file. In this case, use the abstract address X. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
97 lines
1.5 KiB
Plaintext
97 lines
1.5 KiB
Plaintext
#include "kirkwood.dtsi"
|
|
#include "kirkwood-6281.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
pinctrl: pin-controller@10000 {
|
|
pmx_ns2_sata0: pmx-ns2-sata0 {
|
|
marvell,pins = "mpp21";
|
|
marvell,function = "sata0";
|
|
};
|
|
pmx_ns2_sata1: pmx-ns2-sata1 {
|
|
marvell,pins = "mpp20";
|
|
marvell,function = "sata1";
|
|
};
|
|
};
|
|
|
|
serial@12000 {
|
|
status = "okay";
|
|
};
|
|
|
|
spi@10600 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "mxicy,mx25l4005a", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <20000000>;
|
|
mode = <0>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x80000>;
|
|
label = "u-boot";
|
|
};
|
|
};
|
|
};
|
|
|
|
i2c@11000 {
|
|
status = "okay";
|
|
|
|
eeprom@50 {
|
|
compatible = "atmel,24c04";
|
|
pagesize = <16>;
|
|
reg = <0x50>;
|
|
};
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
power {
|
|
label = "Power push button";
|
|
linux,code = <KEY_POWER>;
|
|
gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
red-fail {
|
|
label = "ns2:red:fail";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
gpio_poweroff {
|
|
compatible = "gpio-poweroff";
|
|
gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
};
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
|
|
ethphy0: ethernet-phy@X {
|
|
/* overwrite reg property in board file */
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
ethernet0-port@0 {
|
|
phy-handle = <ðphy0>;
|
|
};
|
|
};
|