05e7d622f1
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
138 lines
2.9 KiB
Plaintext
138 lines
2.9 KiB
Plaintext
/*
|
|
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
|
|
*/
|
|
|
|
/ {
|
|
tfp410: encoder {
|
|
compatible = "ti,tfp410";
|
|
|
|
powerdown-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* gpio_54 */
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tfp410_pins>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
tfp410_in: endpoint {
|
|
remote-endpoint = <&dpi_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
tfp410_out: endpoint {
|
|
remote-endpoint = <&dvi_connector_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
dvi0: connector {
|
|
compatible = "dvi-connector";
|
|
label = "dvi";
|
|
|
|
port {
|
|
dvi_connector_in: endpoint {
|
|
remote-endpoint = <&tfp410_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
audio_amp: audio_amp {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "audio_amp";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sb_t35_audio_amp>;
|
|
gpio = <&gpio2 29 GPIO_ACTIVE_LOW>; /* gpio_61 */
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
smsc2_pins: pinmux_smsc2_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */
|
|
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */
|
|
>;
|
|
};
|
|
|
|
tfp410_pins: pinmux_tfp410_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
|
|
>;
|
|
};
|
|
|
|
i2c3_pins: pinmux_i2c3_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
|
|
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
|
|
>;
|
|
};
|
|
|
|
sb_t35_audio_amp: pinmux_sb_t35_audio_amp {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4) /* gpmc_nbe1.gpio_61 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&i2c3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c3_pins>;
|
|
|
|
clock-frequency = <400000>;
|
|
|
|
at24@50 {
|
|
compatible = "atmel,24c02";
|
|
pagesize = <16>;
|
|
reg = <0x50>;
|
|
};
|
|
};
|
|
|
|
&gpmc {
|
|
ranges = <4 0 0x2d000000 0x01000000>;
|
|
|
|
smsc2: ethernet@4,0 {
|
|
compatible = "smsc,lan9221", "smsc,lan9115";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&smsc2_pins>;
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
|
|
reg = <4 0 0xff>;
|
|
bank-width = <2>;
|
|
gpmc,device-width = <1>;
|
|
gpmc,cycle2cycle-samecsen = <1>;
|
|
gpmc,cycle2cycle-diffcsen = <1>;
|
|
gpmc,cs-on-ns = <5>;
|
|
gpmc,cs-rd-off-ns = <150>;
|
|
gpmc,cs-wr-off-ns = <150>;
|
|
gpmc,adv-on-ns = <0>;
|
|
gpmc,adv-rd-off-ns = <15>;
|
|
gpmc,adv-wr-off-ns = <40>;
|
|
gpmc,oe-on-ns = <45>;
|
|
gpmc,oe-off-ns = <140>;
|
|
gpmc,we-on-ns = <45>;
|
|
gpmc,we-off-ns = <140>;
|
|
gpmc,rd-cycle-ns = <155>;
|
|
gpmc,wr-cycle-ns = <155>;
|
|
gpmc,access-ns = <120>;
|
|
gpmc,page-burst-access-ns = <20>;
|
|
gpmc,bus-turnaround-ns = <75>;
|
|
gpmc,cycle2cycle-delay-ns = <75>;
|
|
gpmc,wait-monitoring-ns = <0>;
|
|
gpmc,clk-activation-ns = <0>;
|
|
gpmc,wr-data-mux-bus-ns = <0>;
|
|
gpmc,wr-access-ns = <0>;
|
|
vddvario-supply = <&vddvario>;
|
|
vdd33a-supply = <&vdd33a>;
|
|
reg-io-width = <4>;
|
|
smsc,save-mac-address;
|
|
};
|
|
};
|