b993292f73
We currently have three device nodes for the same USB hardware block, as evident by the reuse of the same reg address multiple times. Now that the chipidea driver fully supports OTG with the MSM wrapper we can collapse the three nodes into one USB device node, reflecting the true nature of the hardware. Since we're here, we also mark the irq trigger flags correctly, as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE. Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
381 lines
6.8 KiB
Plaintext
381 lines
6.8 KiB
Plaintext
#include "qcom-apq8064-v2.0.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
|
|
/ {
|
|
model = "Qualcomm APQ8064/IFC6410";
|
|
compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
|
|
|
|
aliases {
|
|
serial0 = &gsbi7_serial;
|
|
serial1 = &gsbi6_serial;
|
|
i2c0 = &gsbi1_i2c;
|
|
i2c1 = &gsbi2_i2c;
|
|
i2c2 = &gsbi3_i2c;
|
|
i2c3 = &gsbi4_i2c;
|
|
spi0 = &gsbi5_spi;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
pwrseq {
|
|
compatible = "simple-bus";
|
|
|
|
sdcc4_pwrseq: sdcc4_pwrseq {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wlan_default_gpios>;
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <¬ify_led>;
|
|
|
|
led@1 {
|
|
label = "apq8064:green:user1";
|
|
gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
hdmi-out {
|
|
compatible = "hdmi-connector";
|
|
type = "d";
|
|
|
|
port {
|
|
hdmi_con: endpoint {
|
|
remote-endpoint = <&hdmi_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
soc {
|
|
pinctrl@800000 {
|
|
card_detect: card_detect {
|
|
mux {
|
|
pins = "gpio26";
|
|
function = "gpio";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pcie_pins: pcie_pinmux {
|
|
mux {
|
|
pins = "gpio27";
|
|
function = "gpio";
|
|
};
|
|
conf {
|
|
pins = "gpio27";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
rpm@108000 {
|
|
regulators {
|
|
vin_lvs1_3_6-supply = <&pm8921_s4>;
|
|
vin_lvs2-supply = <&pm8921_s1>;
|
|
vin_lvs4_5_7-supply = <&pm8921_s4>;
|
|
|
|
vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
|
|
vdd_l24-supply = <&pm8921_s1>;
|
|
vdd_l25-supply = <&pm8921_s1>;
|
|
vdd_l26-supply = <&pm8921_s7>;
|
|
vdd_l27-supply = <&pm8921_s7>;
|
|
vdd_l28-supply = <&pm8921_s7>;
|
|
|
|
|
|
/* Buck SMPS */
|
|
s1 {
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <1225000>;
|
|
regulator-max-microvolt = <1225000>;
|
|
qcom,switch-mode-frequency = <3200000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
s3 {
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1400000>;
|
|
qcom,switch-mode-frequency = <4800000>;
|
|
};
|
|
|
|
s4 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
qcom,switch-mode-frequency = <3200000>;
|
|
};
|
|
|
|
s7 {
|
|
regulator-min-microvolt = <1300000>;
|
|
regulator-max-microvolt = <1300000>;
|
|
qcom,switch-mode-frequency = <3200000>;
|
|
};
|
|
|
|
l3 {
|
|
regulator-min-microvolt = <3050000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
l4 {
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
l5 {
|
|
regulator-min-microvolt = <2750000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
l6 {
|
|
regulator-min-microvolt = <2950000>;
|
|
regulator-max-microvolt = <2950000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
l23 {
|
|
regulator-min-microvolt = <1700000>;
|
|
regulator-max-microvolt = <1900000>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
lvs1 {
|
|
bias-pull-down;
|
|
};
|
|
|
|
lvs6 {
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
};
|
|
|
|
ext_3p3v: regulator-fixed@1 {
|
|
compatible = "regulator-fixed";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-name = "ext_3p3v";
|
|
regulator-type = "voltage";
|
|
startup-delay-us = <0>;
|
|
gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
gsbi3: gsbi@16200000 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_I2C>;
|
|
i2c@16280000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
gsbi@16300000 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_I2C>;
|
|
/* CAM I2C MIPI-CSI connector */
|
|
i2c@16380000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
gsbi@12440000 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_I2C>;
|
|
|
|
i2c@12460000 {
|
|
status = "okay";
|
|
clock-frequency = <200000>;
|
|
|
|
eeprom@52 {
|
|
compatible = "atmel,24c128";
|
|
reg = <0x52>;
|
|
pagesize = <32>;
|
|
};
|
|
};
|
|
};
|
|
|
|
gsbi@1a200000 {
|
|
qcom,mode = <GSBI_PROT_SPI>;
|
|
status = "okay";
|
|
spi4: spi@1a280000 {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
cs-gpios = <&tlmm_pinmux 53 0>;
|
|
};
|
|
};
|
|
|
|
gsbi@16500000 {
|
|
status = "ok";
|
|
qcom,mode = <GSBI_PROT_UART_W_FC>;
|
|
|
|
serial@16540000 {
|
|
status = "ok";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gsbi6_uart_4pins>;
|
|
};
|
|
};
|
|
|
|
gsbi@16600000 {
|
|
status = "ok";
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
serial@16640000 {
|
|
status = "ok";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gsbi7_uart_2pins>;
|
|
};
|
|
};
|
|
|
|
sata_phy0: phy@1b400000 {
|
|
status = "okay";
|
|
};
|
|
|
|
sata0: sata@29000000 {
|
|
status = "okay";
|
|
target-supply = <&pm8921_s4>;
|
|
};
|
|
|
|
/* OTG */
|
|
usb@12500000 {
|
|
status = "okay";
|
|
dr_mode = "otg";
|
|
ulpi {
|
|
phy {
|
|
v3p3-supply = <&pm8921_l3>;
|
|
v1p8-supply = <&pm8921_l4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
usb@12520000 {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
ulpi {
|
|
phy {
|
|
v3p3-supply = <&pm8921_l3>;
|
|
v1p8-supply = <&pm8921_l23>;
|
|
};
|
|
};
|
|
};
|
|
|
|
usb@12530000 {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
ulpi {
|
|
phy {
|
|
v3p3-supply = <&pm8921_l3>;
|
|
v1p8-supply = <&pm8921_l23>;
|
|
};
|
|
};
|
|
};
|
|
|
|
pci@1b500000 {
|
|
status = "ok";
|
|
vdda-supply = <&pm8921_s3>;
|
|
vdda_phy-supply = <&pm8921_lvs6>;
|
|
vdda_refclk-supply = <&ext_3p3v>;
|
|
pinctrl-0 = <&pcie_pins>;
|
|
pinctrl-names = "default";
|
|
perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
qcom,ssbi@500000 {
|
|
pmic@0 {
|
|
gpio@150 {
|
|
wlan_default_gpios: wlan-gpios {
|
|
pios {
|
|
pins = "gpio43";
|
|
function = "normal";
|
|
bias-disable;
|
|
power-source = <PM8921_GPIO_S4>;
|
|
};
|
|
};
|
|
|
|
notify_led: nled {
|
|
pios {
|
|
pins = "gpio18";
|
|
function = "normal";
|
|
bias-disable;
|
|
power-source = <PM8921_GPIO_S4>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
amba {
|
|
/* eMMC */
|
|
sdcc1: sdcc@12400000 {
|
|
status = "okay";
|
|
vmmc-supply = <&pm8921_l5>;
|
|
vqmmc-supply = <&pm8921_s4>;
|
|
};
|
|
|
|
/* External micro SD card */
|
|
sdcc3: sdcc@12180000 {
|
|
status = "okay";
|
|
vmmc-supply = <&pm8921_l6>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&card_detect>;
|
|
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
/* WLAN */
|
|
sdcc4: sdcc@121c0000 {
|
|
status = "okay";
|
|
vmmc-supply = <&ext_3p3v>;
|
|
vqmmc-supply = <&pm8921_lvs1>;
|
|
mmc-pwrseq = <&sdcc4_pwrseq>;
|
|
};
|
|
};
|
|
|
|
hdmi-tx@4a00000 {
|
|
status = "okay";
|
|
|
|
core-vdda-supply = <&pm8921_hdmi_switch>;
|
|
hdmi-mux-supply = <&ext_3p3v>;
|
|
|
|
hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
|
|
|
|
ports {
|
|
port@0 {
|
|
endpoint {
|
|
remote-endpoint = <&mdp_dtv_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
endpoint {
|
|
remote-endpoint = <&hdmi_con>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi-phy@4a00400 {
|
|
status = "okay";
|
|
|
|
core-vdda-supply = <&pm8921_hdmi_switch>;
|
|
};
|
|
|
|
mdp@5100000 {
|
|
status = "okay";
|
|
|
|
ports {
|
|
port@3 {
|
|
endpoint {
|
|
remote-endpoint = <&hdmi_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|