![Rob Herring](/assets/img/avatar_default.png)
Move custom orion platforms gpio code to orion-gpio to remove the dependency on mach/gpio.h. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch>
364 lines
9.3 KiB
C
364 lines
9.3 KiB
C
/*
|
|
* arch/arm/mach-orion5x/d2net-setup.c
|
|
*
|
|
* LaCie d2Network and Big Disk Network NAS setup
|
|
*
|
|
* Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/mtd/physmap.h>
|
|
#include <linux/mv643xx_eth.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/gpio_keys.h>
|
|
#include <linux/input.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/ata_platform.h>
|
|
#include <linux/gpio.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/pci.h>
|
|
#include <mach/orion5x.h>
|
|
#include <plat/orion-gpio.h>
|
|
#include "common.h"
|
|
#include "mpp.h"
|
|
|
|
/*****************************************************************************
|
|
* LaCie d2 Network Info
|
|
****************************************************************************/
|
|
|
|
/*
|
|
* 512KB NOR flash Device bus boot chip select
|
|
*/
|
|
|
|
#define D2NET_NOR_BOOT_BASE 0xfff80000
|
|
#define D2NET_NOR_BOOT_SIZE SZ_512K
|
|
|
|
/*****************************************************************************
|
|
* 512KB NOR Flash on Boot Device
|
|
****************************************************************************/
|
|
|
|
/*
|
|
* TODO: Check write support on flash MX29LV400CBTC-70G
|
|
*/
|
|
|
|
static struct mtd_partition d2net_partitions[] = {
|
|
{
|
|
.name = "Full512kb",
|
|
.size = MTDPART_SIZ_FULL,
|
|
.offset = 0,
|
|
.mask_flags = MTD_WRITEABLE,
|
|
},
|
|
};
|
|
|
|
static struct physmap_flash_data d2net_nor_flash_data = {
|
|
.width = 1,
|
|
.parts = d2net_partitions,
|
|
.nr_parts = ARRAY_SIZE(d2net_partitions),
|
|
};
|
|
|
|
static struct resource d2net_nor_flash_resource = {
|
|
.flags = IORESOURCE_MEM,
|
|
.start = D2NET_NOR_BOOT_BASE,
|
|
.end = D2NET_NOR_BOOT_BASE
|
|
+ D2NET_NOR_BOOT_SIZE - 1,
|
|
};
|
|
|
|
static struct platform_device d2net_nor_flash = {
|
|
.name = "physmap-flash",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &d2net_nor_flash_data,
|
|
},
|
|
.num_resources = 1,
|
|
.resource = &d2net_nor_flash_resource,
|
|
};
|
|
|
|
/*****************************************************************************
|
|
* Ethernet
|
|
****************************************************************************/
|
|
|
|
static struct mv643xx_eth_platform_data d2net_eth_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
|
|
};
|
|
|
|
/*****************************************************************************
|
|
* I2C devices
|
|
****************************************************************************/
|
|
|
|
/*
|
|
* i2c addr | chip | description
|
|
* 0x32 | Ricoh 5C372b | RTC
|
|
* 0x3e | GMT G762 | PWM fan controller
|
|
* 0x50 | HT24LC08 | eeprom (1kB)
|
|
*
|
|
* TODO: Add G762 support to the g760a driver.
|
|
*/
|
|
static struct i2c_board_info __initdata d2net_i2c_devices[] = {
|
|
{
|
|
I2C_BOARD_INFO("rs5c372b", 0x32),
|
|
}, {
|
|
I2C_BOARD_INFO("24c08", 0x50),
|
|
},
|
|
};
|
|
|
|
/*****************************************************************************
|
|
* SATA
|
|
****************************************************************************/
|
|
|
|
static struct mv_sata_platform_data d2net_sata_data = {
|
|
.n_ports = 2,
|
|
};
|
|
|
|
#define D2NET_GPIO_SATA0_POWER 3
|
|
#define D2NET_GPIO_SATA1_POWER 12
|
|
|
|
static void __init d2net_sata_power_init(void)
|
|
{
|
|
int err;
|
|
|
|
err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
|
|
if (err == 0) {
|
|
err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
|
|
if (err)
|
|
gpio_free(D2NET_GPIO_SATA0_POWER);
|
|
}
|
|
if (err)
|
|
pr_err("d2net: failed to configure SATA0 power GPIO\n");
|
|
|
|
err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
|
|
if (err == 0) {
|
|
err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
|
|
if (err)
|
|
gpio_free(D2NET_GPIO_SATA1_POWER);
|
|
}
|
|
if (err)
|
|
pr_err("d2net: failed to configure SATA1 power GPIO\n");
|
|
}
|
|
|
|
/*****************************************************************************
|
|
* GPIO LED's
|
|
****************************************************************************/
|
|
|
|
/*
|
|
* The blue front LED is wired to the CPLD and can blink in relation with the
|
|
* SATA activity.
|
|
*
|
|
* The following array detail the different LED registers and the combination
|
|
* of their possible values:
|
|
*
|
|
* led_off | blink_ctrl | SATA active | LED state
|
|
* | | |
|
|
* 1 | x | x | off
|
|
* 0 | 0 | 0 | off
|
|
* 0 | 1 | 0 | blink (rate 300ms)
|
|
* 0 | x | 1 | on
|
|
*
|
|
* Notes: The blue and the red front LED's can't be on at the same time.
|
|
* Red LED have priority.
|
|
*/
|
|
|
|
#define D2NET_GPIO_RED_LED 6
|
|
#define D2NET_GPIO_BLUE_LED_BLINK_CTRL 16
|
|
#define D2NET_GPIO_BLUE_LED_OFF 23
|
|
|
|
static struct gpio_led d2net_leds[] = {
|
|
{
|
|
.name = "d2net:blue:sata",
|
|
.default_trigger = "default-on",
|
|
.gpio = D2NET_GPIO_BLUE_LED_OFF,
|
|
.active_low = 1,
|
|
},
|
|
{
|
|
.name = "d2net:red:fail",
|
|
.gpio = D2NET_GPIO_RED_LED,
|
|
},
|
|
};
|
|
|
|
static struct gpio_led_platform_data d2net_led_data = {
|
|
.num_leds = ARRAY_SIZE(d2net_leds),
|
|
.leds = d2net_leds,
|
|
};
|
|
|
|
static struct platform_device d2net_gpio_leds = {
|
|
.name = "leds-gpio",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &d2net_led_data,
|
|
},
|
|
};
|
|
|
|
static void __init d2net_gpio_leds_init(void)
|
|
{
|
|
int err;
|
|
|
|
/* Configure GPIO over MPP max number. */
|
|
orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
|
|
|
|
/* Configure register blink_ctrl to allow SATA activity LED blinking. */
|
|
err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
|
|
if (err == 0) {
|
|
err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
|
|
if (err)
|
|
gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
|
|
}
|
|
if (err)
|
|
pr_err("d2net: failed to configure blue LED blink GPIO\n");
|
|
|
|
platform_device_register(&d2net_gpio_leds);
|
|
}
|
|
|
|
/****************************************************************************
|
|
* GPIO keys
|
|
****************************************************************************/
|
|
|
|
#define D2NET_GPIO_PUSH_BUTTON 18
|
|
#define D2NET_GPIO_POWER_SWITCH_ON 8
|
|
#define D2NET_GPIO_POWER_SWITCH_OFF 9
|
|
|
|
#define D2NET_SWITCH_POWER_ON 0x1
|
|
#define D2NET_SWITCH_POWER_OFF 0x2
|
|
|
|
static struct gpio_keys_button d2net_buttons[] = {
|
|
{
|
|
.type = EV_SW,
|
|
.code = D2NET_SWITCH_POWER_OFF,
|
|
.gpio = D2NET_GPIO_POWER_SWITCH_OFF,
|
|
.desc = "Power rocker switch (auto|off)",
|
|
.active_low = 0,
|
|
},
|
|
{
|
|
.type = EV_SW,
|
|
.code = D2NET_SWITCH_POWER_ON,
|
|
.gpio = D2NET_GPIO_POWER_SWITCH_ON,
|
|
.desc = "Power rocker switch (on|auto)",
|
|
.active_low = 0,
|
|
},
|
|
{
|
|
.type = EV_KEY,
|
|
.code = KEY_POWER,
|
|
.gpio = D2NET_GPIO_PUSH_BUTTON,
|
|
.desc = "Front Push Button",
|
|
.active_low = 0,
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_platform_data d2net_button_data = {
|
|
.buttons = d2net_buttons,
|
|
.nbuttons = ARRAY_SIZE(d2net_buttons),
|
|
};
|
|
|
|
static struct platform_device d2net_gpio_buttons = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &d2net_button_data,
|
|
},
|
|
};
|
|
|
|
/*****************************************************************************
|
|
* General Setup
|
|
****************************************************************************/
|
|
|
|
static unsigned int d2net_mpp_modes[] __initdata = {
|
|
MPP0_GPIO, /* Board ID (bit 0) */
|
|
MPP1_GPIO, /* Board ID (bit 1) */
|
|
MPP2_GPIO, /* Board ID (bit 2) */
|
|
MPP3_GPIO, /* SATA 0 power */
|
|
MPP4_UNUSED,
|
|
MPP5_GPIO, /* Fan fail detection */
|
|
MPP6_GPIO, /* Red front LED */
|
|
MPP7_UNUSED,
|
|
MPP8_GPIO, /* Rear power switch (on|auto) */
|
|
MPP9_GPIO, /* Rear power switch (auto|off) */
|
|
MPP10_UNUSED,
|
|
MPP11_UNUSED,
|
|
MPP12_GPIO, /* SATA 1 power */
|
|
MPP13_UNUSED,
|
|
MPP14_SATA_LED, /* SATA 0 active */
|
|
MPP15_SATA_LED, /* SATA 1 active */
|
|
MPP16_GPIO, /* Blue front LED blink control */
|
|
MPP17_UNUSED,
|
|
MPP18_GPIO, /* Front button (0 = Released, 1 = Pushed ) */
|
|
MPP19_UNUSED,
|
|
0,
|
|
/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
|
|
/* 23: Blue front LED off */
|
|
/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
|
|
};
|
|
|
|
#define D2NET_GPIO_INHIBIT_POWER_OFF 24
|
|
|
|
static void __init d2net_init(void)
|
|
{
|
|
/*
|
|
* Setup basic Orion functions. Need to be called early.
|
|
*/
|
|
orion5x_init();
|
|
|
|
orion5x_mpp_conf(d2net_mpp_modes);
|
|
|
|
/*
|
|
* Configure peripherals.
|
|
*/
|
|
orion5x_ehci0_init();
|
|
orion5x_eth_init(&d2net_eth_data);
|
|
orion5x_i2c_init();
|
|
orion5x_uart0_init();
|
|
|
|
d2net_sata_power_init();
|
|
orion5x_sata_init(&d2net_sata_data);
|
|
|
|
orion5x_setup_dev_boot_win(D2NET_NOR_BOOT_BASE,
|
|
D2NET_NOR_BOOT_SIZE);
|
|
platform_device_register(&d2net_nor_flash);
|
|
|
|
platform_device_register(&d2net_gpio_buttons);
|
|
|
|
d2net_gpio_leds_init();
|
|
|
|
pr_notice("d2net: Flash write are not yet supported.\n");
|
|
|
|
i2c_register_board_info(0, d2net_i2c_devices,
|
|
ARRAY_SIZE(d2net_i2c_devices));
|
|
|
|
orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
|
|
}
|
|
|
|
/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
|
|
|
|
#ifdef CONFIG_MACH_D2NET
|
|
MACHINE_START(D2NET, "LaCie d2 Network")
|
|
.atag_offset = 0x100,
|
|
.init_machine = d2net_init,
|
|
.map_io = orion5x_map_io,
|
|
.init_early = orion5x_init_early,
|
|
.init_irq = orion5x_init_irq,
|
|
.timer = &orion5x_timer,
|
|
.fixup = tag_fixup_mem32,
|
|
.restart = orion5x_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACH_BIGDISK
|
|
MACHINE_START(BIGDISK, "LaCie Big Disk Network")
|
|
.atag_offset = 0x100,
|
|
.init_machine = d2net_init,
|
|
.map_io = orion5x_map_io,
|
|
.init_early = orion5x_init_early,
|
|
.init_irq = orion5x_init_irq,
|
|
.timer = &orion5x_timer,
|
|
.fixup = tag_fixup_mem32,
|
|
.restart = orion5x_restart,
|
|
MACHINE_END
|
|
#endif
|
|
|