![Anant Gole](/assets/img/avatar_default.png)
TI HECC (High End CAN Controller) module is found on many TI devices. It has 32 hardware mailboxes with full implementation of CAN protocol 2.0B with bus speeds up to 1Mbps. Specifications of the module are available on TI web <http://www.ti.com> Signed-off-by: Anant Gole <anantgole@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
116 lines
3.8 KiB
Plaintext
116 lines
3.8 KiB
Plaintext
menu "CAN Device Drivers"
|
|
depends on CAN
|
|
|
|
config CAN_VCAN
|
|
tristate "Virtual Local CAN Interface (vcan)"
|
|
depends on CAN
|
|
default N
|
|
---help---
|
|
Similar to the network loopback devices, vcan offers a
|
|
virtual local CAN interface.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called vcan.
|
|
|
|
config CAN_DEV
|
|
tristate "Platform CAN drivers with Netlink support"
|
|
depends on CAN
|
|
default Y
|
|
---help---
|
|
Enables the common framework for platform CAN drivers with Netlink
|
|
support. This is the standard library for CAN drivers.
|
|
If unsure, say Y.
|
|
|
|
config CAN_CALC_BITTIMING
|
|
bool "CAN bit-timing calculation"
|
|
depends on CAN_DEV
|
|
default Y
|
|
---help---
|
|
If enabled, CAN bit-timing parameters will be calculated for the
|
|
bit-rate specified via Netlink argument "bitrate" when the device
|
|
get started. This works fine for the most common CAN controllers
|
|
with standard bit-rates but may fail for exotic bit-rates or CAN
|
|
source clock frequencies. Disabling saves some space, but then the
|
|
bit-timing parameters must be specified directly using the Netlink
|
|
arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
|
|
If unsure, say Y.
|
|
|
|
config CAN_SJA1000
|
|
depends on CAN_DEV && HAS_IOMEM
|
|
tristate "Philips SJA1000"
|
|
---help---
|
|
Driver for the SJA1000 CAN controllers from Philips or NXP
|
|
|
|
config CAN_SJA1000_ISA
|
|
depends on CAN_SJA1000 && ISA
|
|
tristate "ISA Bus based legacy SJA1000 driver"
|
|
---help---
|
|
This driver adds legacy support for SJA1000 chips connected to
|
|
the ISA bus using I/O port, memory mapped or indirect access.
|
|
|
|
config CAN_SJA1000_PLATFORM
|
|
depends on CAN_SJA1000
|
|
tristate "Generic Platform Bus based SJA1000 driver"
|
|
---help---
|
|
This driver adds support for the SJA1000 chips connected to
|
|
the "platform bus" (Linux abstraction for directly to the
|
|
processor attached devices). Which can be found on various
|
|
boards from Phytec (http://www.phytec.de) like the PCM027,
|
|
PCM038.
|
|
|
|
config CAN_SJA1000_OF_PLATFORM
|
|
depends on CAN_SJA1000 && PPC_OF
|
|
tristate "Generic OF Platform Bus based SJA1000 driver"
|
|
---help---
|
|
This driver adds support for the SJA1000 chips connected to
|
|
the OpenFirmware "platform bus" found on embedded systems with
|
|
OpenFirmware bindings, e.g. if you have a PowerPC based system
|
|
you may want to enable this option.
|
|
|
|
config CAN_EMS_PCI
|
|
tristate "EMS CPC-PCI, CPC-PCIe and CPC-104P Card"
|
|
depends on PCI && CAN_SJA1000
|
|
---help---
|
|
This driver is for the one, two or four channel CPC-PCI,
|
|
CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
|
|
(http://www.ems-wuensche.de).
|
|
|
|
config CAN_EMS_USB
|
|
tristate "EMS CPC-USB/ARM7 CAN/USB interface"
|
|
depends on USB && CAN_DEV
|
|
---help---
|
|
This driver is for the one channel CPC-USB/ARM7 CAN/USB interface
|
|
from from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
|
|
|
|
config CAN_KVASER_PCI
|
|
tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
|
|
depends on PCI && CAN_SJA1000
|
|
---help---
|
|
This driver is for the the PCIcanx and PCIcan cards (1, 2 or
|
|
4 channel) from Kvaser (http://www.kvaser.com).
|
|
|
|
config CAN_AT91
|
|
tristate "Atmel AT91 onchip CAN controller"
|
|
depends on CAN && CAN_DEV && ARCH_AT91SAM9263
|
|
---help---
|
|
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
|
|
|
|
config CAN_TI_HECC
|
|
depends on CAN_DEV && ARCH_OMAP3
|
|
tristate "TI High End CAN Controller"
|
|
---help---
|
|
Driver for TI HECC (High End CAN Controller) module found on many
|
|
TI devices. The device specifications are available from www.ti.com
|
|
|
|
config CAN_DEBUG_DEVICES
|
|
bool "CAN devices debugging messages"
|
|
depends on CAN
|
|
default N
|
|
---help---
|
|
Say Y here if you want the CAN device drivers to produce a bunch of
|
|
debug messages to the system log. Select this if you are having
|
|
a problem with CAN support and want to see more of what is going
|
|
on.
|
|
|
|
endmenu
|