hwmon: Add Texas Instruments TMP108 temperature sensor driver.
Add support for the TI TMP108 temperature sensor with some device configuration parameters. Signed-off-by: John Muir <john@jmuir.com> [groeck: Initialize of_match_table] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit is contained in:
parent
3a412d5e4a
commit
66e1c91713
36
Documentation/hwmon/tmp108
Normal file
36
Documentation/hwmon/tmp108
Normal file
|
@ -0,0 +1,36 @@
|
|||
Kernel driver tmp108
|
||||
====================
|
||||
|
||||
Supported chips:
|
||||
* Texas Instruments TMP108
|
||||
Prefix: 'tmp108'
|
||||
Addresses scanned: none
|
||||
Datasheet: http://www.ti.com/product/tmp108
|
||||
|
||||
Author:
|
||||
John Muir <john@jmuir.com>
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
The Texas Instruments TMP108 implements one temperature sensor. An alert pin
|
||||
can be set when temperatures exceed minimum or maximum values plus or minus a
|
||||
hysteresis value. (This driver does not support interrupts for the alert pin,
|
||||
and the device runs in comparator mode.)
|
||||
|
||||
The sensor is accurate to 0.75C over the range of -25 to +85 C, and to 1.0
|
||||
degree from -40 to +125 C. Resolution of the sensor is 0.0625 degree. The
|
||||
operating temperature has a minimum of -55 C and a maximum of +150 C.
|
||||
Hysteresis values can be set to 0, 1, 2, or 4C.
|
||||
|
||||
The TMP108 has a programmable update rate that can select between 8, 4, 1, and
|
||||
0.5 Hz.
|
||||
|
||||
By default the TMP108 reads the temperature continuously. To conserve power,
|
||||
the TMP108 has a one-shot mode where the device is normally shut-down. When a
|
||||
one shot is requested the temperature is read, the result can be retrieved,
|
||||
and then the device is shut down automatically. (This driver only supports
|
||||
continuous mode.)
|
||||
|
||||
The driver provides the common sysfs-interface for temperatures (see
|
||||
Documentation/hwmon/sysfs-interface under Temperatures).
|
|
@ -1602,6 +1602,17 @@ config SENSORS_TMP103
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called tmp103.
|
||||
|
||||
config SENSORS_TMP108
|
||||
tristate "Texas Instruments TMP108"
|
||||
depends on I2C
|
||||
select REGMAP_I2C
|
||||
help
|
||||
If you say yes here you get support for Texas Instruments TMP108
|
||||
sensor chips.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called tmp108.
|
||||
|
||||
config SENSORS_TMP401
|
||||
tristate "Texas Instruments TMP401 and compatibles"
|
||||
depends on I2C
|
||||
|
|
|
@ -153,6 +153,7 @@ obj-$(CONFIG_SENSORS_TC74) += tc74.o
|
|||
obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
|
||||
obj-$(CONFIG_SENSORS_TMP102) += tmp102.o
|
||||
obj-$(CONFIG_SENSORS_TMP103) += tmp103.o
|
||||
obj-$(CONFIG_SENSORS_TMP108) += tmp108.o
|
||||
obj-$(CONFIG_SENSORS_TMP401) += tmp401.o
|
||||
obj-$(CONFIG_SENSORS_TMP421) += tmp421.o
|
||||
obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.o
|
||||
|
|
469
drivers/hwmon/tmp108.c
Normal file
469
drivers/hwmon/tmp108.c
Normal file
|
@ -0,0 +1,469 @@
|
|||
/* Texas Instruments TMP108 SMBus temperature sensor driver
|
||||
*
|
||||
* Copyright (C) 2016 John Muir <john@jmuir.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/delay.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/err.h>
|
||||
#include <linux/hwmon.h>
|
||||
#include <linux/hwmon-sysfs.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/mutex.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/jiffies.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
#define DRIVER_NAME "tmp108"
|
||||
|
||||
#define TMP108_REG_TEMP 0x00
|
||||
#define TMP108_REG_CONF 0x01
|
||||
#define TMP108_REG_TLOW 0x02
|
||||
#define TMP108_REG_THIGH 0x03
|
||||
|
||||
#define TMP108_TEMP_MIN_MC -50000 /* Minimum millicelcius. */
|
||||
#define TMP108_TEMP_MAX_MC 127937 /* Maximum millicelcius. */
|
||||
|
||||
/* Configuration register bits.
|
||||
* Note: these bit definitions are byte swapped.
|
||||
*/
|
||||
#define TMP108_CONF_M0 0x0100 /* Sensor mode. */
|
||||
#define TMP108_CONF_M1 0x0200
|
||||
#define TMP108_CONF_TM 0x0400 /* Thermostat mode. */
|
||||
#define TMP108_CONF_FL 0x0800 /* Watchdog flag - TLOW */
|
||||
#define TMP108_CONF_FH 0x1000 /* Watchdog flag - THIGH */
|
||||
#define TMP108_CONF_CR0 0x2000 /* Conversion rate. */
|
||||
#define TMP108_CONF_CR1 0x4000
|
||||
#define TMP108_CONF_ID 0x8000
|
||||
#define TMP108_CONF_HYS0 0x0010 /* Hysteresis. */
|
||||
#define TMP108_CONF_HYS1 0x0020
|
||||
#define TMP108_CONF_POL 0x0080 /* Polarity of alert. */
|
||||
|
||||
/* Defaults set by the hardware upon reset. */
|
||||
#define TMP108_CONF_DEFAULTS (TMP108_CONF_CR0 | TMP108_CONF_TM |\
|
||||
TMP108_CONF_HYS0 | TMP108_CONF_M1)
|
||||
/* These bits are read-only. */
|
||||
#define TMP108_CONF_READ_ONLY (TMP108_CONF_FL | TMP108_CONF_FH |\
|
||||
TMP108_CONF_ID)
|
||||
|
||||
#define TMP108_CONF_MODE_MASK (TMP108_CONF_M0|TMP108_CONF_M1)
|
||||
#define TMP108_MODE_SHUTDOWN 0x0000
|
||||
#define TMP108_MODE_ONE_SHOT TMP108_CONF_M0
|
||||
#define TMP108_MODE_CONTINUOUS TMP108_CONF_M1 /* Default */
|
||||
/* When M1 is set, M0 is ignored. */
|
||||
|
||||
#define TMP108_CONF_CONVRATE_MASK (TMP108_CONF_CR0|TMP108_CONF_CR1)
|
||||
#define TMP108_CONVRATE_0P25HZ 0x0000
|
||||
#define TMP108_CONVRATE_1HZ TMP108_CONF_CR0 /* Default */
|
||||
#define TMP108_CONVRATE_4HZ TMP108_CONF_CR1
|
||||
#define TMP108_CONVRATE_16HZ (TMP108_CONF_CR0|TMP108_CONF_CR1)
|
||||
|
||||
#define TMP108_CONF_HYSTERESIS_MASK (TMP108_CONF_HYS0|TMP108_CONF_HYS1)
|
||||
#define TMP108_HYSTERESIS_0C 0x0000
|
||||
#define TMP108_HYSTERESIS_1C TMP108_CONF_HYS0 /* Default */
|
||||
#define TMP108_HYSTERESIS_2C TMP108_CONF_HYS1
|
||||
#define TMP108_HYSTERESIS_4C (TMP108_CONF_HYS0|TMP108_CONF_HYS1)
|
||||
|
||||
#define TMP108_CONVERSION_TIME_MS 30 /* in milli-seconds */
|
||||
|
||||
struct tmp108 {
|
||||
struct regmap *regmap;
|
||||
u16 orig_config;
|
||||
unsigned long ready_time;
|
||||
};
|
||||
|
||||
/* convert 12-bit TMP108 register value to milliCelsius */
|
||||
static inline int tmp108_temp_reg_to_mC(s16 val)
|
||||
{
|
||||
return (val & ~0x0f) * 1000 / 256;
|
||||
}
|
||||
|
||||
/* convert milliCelsius to left adjusted 12-bit TMP108 register value */
|
||||
static inline u16 tmp108_mC_to_temp_reg(int val)
|
||||
{
|
||||
return (val * 256) / 1000;
|
||||
}
|
||||
|
||||
static int tmp108_read(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int channel, long *temp)
|
||||
{
|
||||
struct tmp108 *tmp108 = dev_get_drvdata(dev);
|
||||
unsigned int regval;
|
||||
int err, hyst;
|
||||
|
||||
if (type == hwmon_chip) {
|
||||
if (attr == hwmon_chip_update_interval) {
|
||||
err = regmap_read(tmp108->regmap, TMP108_REG_CONF,
|
||||
®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
switch (regval & TMP108_CONF_CONVRATE_MASK) {
|
||||
case TMP108_CONVRATE_0P25HZ:
|
||||
default:
|
||||
*temp = 4000;
|
||||
break;
|
||||
case TMP108_CONVRATE_1HZ:
|
||||
*temp = 1000;
|
||||
break;
|
||||
case TMP108_CONVRATE_4HZ:
|
||||
*temp = 250;
|
||||
break;
|
||||
case TMP108_CONVRATE_16HZ:
|
||||
*temp = 63;
|
||||
break;
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
|
||||
switch (attr) {
|
||||
case hwmon_temp_input:
|
||||
/* Is it too early to return a conversion ? */
|
||||
if (time_before(jiffies, tmp108->ready_time)) {
|
||||
dev_dbg(dev, "%s: Conversion not ready yet..\n",
|
||||
__func__);
|
||||
return -EAGAIN;
|
||||
}
|
||||
err = regmap_read(tmp108->regmap, TMP108_REG_TEMP, ®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
*temp = tmp108_temp_reg_to_mC(regval);
|
||||
break;
|
||||
case hwmon_temp_min:
|
||||
case hwmon_temp_max:
|
||||
err = regmap_read(tmp108->regmap, attr == hwmon_temp_min ?
|
||||
TMP108_REG_TLOW : TMP108_REG_THIGH, ®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
*temp = tmp108_temp_reg_to_mC(regval);
|
||||
break;
|
||||
case hwmon_temp_min_alarm:
|
||||
case hwmon_temp_max_alarm:
|
||||
err = regmap_read(tmp108->regmap, TMP108_REG_CONF, ®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
*temp = !!(regval & (attr == hwmon_temp_min_alarm ?
|
||||
TMP108_CONF_FL : TMP108_CONF_FH));
|
||||
break;
|
||||
case hwmon_temp_min_hyst:
|
||||
case hwmon_temp_max_hyst:
|
||||
err = regmap_read(tmp108->regmap, TMP108_REG_CONF, ®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
switch (regval & TMP108_CONF_HYSTERESIS_MASK) {
|
||||
case TMP108_HYSTERESIS_0C:
|
||||
default:
|
||||
hyst = 0;
|
||||
break;
|
||||
case TMP108_HYSTERESIS_1C:
|
||||
hyst = 1000;
|
||||
break;
|
||||
case TMP108_HYSTERESIS_2C:
|
||||
hyst = 2000;
|
||||
break;
|
||||
case TMP108_HYSTERESIS_4C:
|
||||
hyst = 4000;
|
||||
break;
|
||||
}
|
||||
err = regmap_read(tmp108->regmap, attr == hwmon_temp_min_hyst ?
|
||||
TMP108_REG_TLOW : TMP108_REG_THIGH, ®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
*temp = tmp108_temp_reg_to_mC(regval);
|
||||
if (attr == hwmon_temp_min_hyst)
|
||||
*temp += hyst;
|
||||
else
|
||||
*temp -= hyst;
|
||||
break;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int tmp108_write(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int channel, long temp)
|
||||
{
|
||||
struct tmp108 *tmp108 = dev_get_drvdata(dev);
|
||||
u32 regval, mask;
|
||||
int err;
|
||||
|
||||
if (type == hwmon_chip) {
|
||||
if (attr == hwmon_chip_update_interval) {
|
||||
if (temp < 156)
|
||||
mask = TMP108_CONVRATE_16HZ;
|
||||
else if (temp < 625)
|
||||
mask = TMP108_CONVRATE_4HZ;
|
||||
else if (temp < 2500)
|
||||
mask = TMP108_CONVRATE_1HZ;
|
||||
else
|
||||
mask = TMP108_CONVRATE_0P25HZ;
|
||||
return regmap_update_bits(tmp108->regmap,
|
||||
TMP108_REG_CONF,
|
||||
TMP108_CONF_CONVRATE_MASK,
|
||||
mask);
|
||||
}
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
|
||||
switch (attr) {
|
||||
case hwmon_temp_min:
|
||||
case hwmon_temp_max:
|
||||
temp = clamp_val(temp, TMP108_TEMP_MIN_MC, TMP108_TEMP_MAX_MC);
|
||||
return regmap_write(tmp108->regmap,
|
||||
attr == hwmon_temp_min ?
|
||||
TMP108_REG_TLOW : TMP108_REG_THIGH,
|
||||
tmp108_mC_to_temp_reg(temp));
|
||||
case hwmon_temp_min_hyst:
|
||||
case hwmon_temp_max_hyst:
|
||||
temp = clamp_val(temp, TMP108_TEMP_MIN_MC, TMP108_TEMP_MAX_MC);
|
||||
err = regmap_read(tmp108->regmap,
|
||||
attr == hwmon_temp_min_hyst ?
|
||||
TMP108_REG_TLOW : TMP108_REG_THIGH,
|
||||
®val);
|
||||
if (err < 0)
|
||||
return err;
|
||||
if (attr == hwmon_temp_min_hyst)
|
||||
temp -= tmp108_temp_reg_to_mC(regval);
|
||||
else
|
||||
temp = tmp108_temp_reg_to_mC(regval) - temp;
|
||||
if (temp < 500)
|
||||
mask = TMP108_HYSTERESIS_0C;
|
||||
else if (temp < 1500)
|
||||
mask = TMP108_HYSTERESIS_1C;
|
||||
else if (temp < 3000)
|
||||
mask = TMP108_HYSTERESIS_2C;
|
||||
else
|
||||
mask = TMP108_HYSTERESIS_4C;
|
||||
return regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
|
||||
TMP108_CONF_HYSTERESIS_MASK, mask);
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
}
|
||||
|
||||
static umode_t tmp108_is_visible(const void *data, enum hwmon_sensor_types type,
|
||||
u32 attr, int channel)
|
||||
{
|
||||
if (type == hwmon_chip && attr == hwmon_chip_update_interval)
|
||||
return 0644;
|
||||
|
||||
if (type != hwmon_temp)
|
||||
return 0;
|
||||
|
||||
switch (attr) {
|
||||
case hwmon_temp_input:
|
||||
case hwmon_temp_min_alarm:
|
||||
case hwmon_temp_max_alarm:
|
||||
return 0444;
|
||||
case hwmon_temp_min:
|
||||
case hwmon_temp_max:
|
||||
case hwmon_temp_min_hyst:
|
||||
case hwmon_temp_max_hyst:
|
||||
return 0644;
|
||||
default:
|
||||
return 0;
|
||||
}
|
||||
}
|
||||
|
||||
static u32 tmp108_chip_config[] = {
|
||||
HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL,
|
||||
0
|
||||
};
|
||||
|
||||
static const struct hwmon_channel_info tmp108_chip = {
|
||||
.type = hwmon_chip,
|
||||
.config = tmp108_chip_config,
|
||||
};
|
||||
|
||||
static u32 tmp108_temp_config[] = {
|
||||
HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MIN | HWMON_T_MIN_HYST
|
||||
| HWMON_T_MAX_HYST | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM,
|
||||
0
|
||||
};
|
||||
|
||||
static const struct hwmon_channel_info tmp108_temp = {
|
||||
.type = hwmon_temp,
|
||||
.config = tmp108_temp_config,
|
||||
};
|
||||
|
||||
static const struct hwmon_channel_info *tmp108_info[] = {
|
||||
&tmp108_chip,
|
||||
&tmp108_temp,
|
||||
NULL
|
||||
};
|
||||
|
||||
static const struct hwmon_ops tmp108_hwmon_ops = {
|
||||
.is_visible = tmp108_is_visible,
|
||||
.read = tmp108_read,
|
||||
.write = tmp108_write,
|
||||
};
|
||||
|
||||
static const struct hwmon_chip_info tmp108_chip_info = {
|
||||
.ops = &tmp108_hwmon_ops,
|
||||
.info = tmp108_info,
|
||||
};
|
||||
|
||||
static void tmp108_restore_config(void *data)
|
||||
{
|
||||
struct tmp108 *tmp108 = data;
|
||||
|
||||
regmap_write(tmp108->regmap, TMP108_REG_CONF, tmp108->orig_config);
|
||||
}
|
||||
|
||||
static bool tmp108_is_writeable_reg(struct device *dev, unsigned int reg)
|
||||
{
|
||||
return reg != TMP108_REG_TEMP;
|
||||
}
|
||||
|
||||
static bool tmp108_is_volatile_reg(struct device *dev, unsigned int reg)
|
||||
{
|
||||
/* Configuration register must be volatile to enable FL and FH. */
|
||||
return reg == TMP108_REG_TEMP || reg == TMP108_REG_CONF;
|
||||
}
|
||||
|
||||
static const struct regmap_config tmp108_regmap_config = {
|
||||
.reg_bits = 8,
|
||||
.val_bits = 16,
|
||||
.max_register = TMP108_REG_THIGH,
|
||||
.writeable_reg = tmp108_is_writeable_reg,
|
||||
.volatile_reg = tmp108_is_volatile_reg,
|
||||
.val_format_endian = REGMAP_ENDIAN_BIG,
|
||||
.cache_type = REGCACHE_RBTREE,
|
||||
.use_single_rw = true,
|
||||
};
|
||||
|
||||
static int tmp108_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct device *dev = &client->dev;
|
||||
struct device *hwmon_dev;
|
||||
struct tmp108 *tmp108;
|
||||
int err;
|
||||
u32 config;
|
||||
|
||||
if (!i2c_check_functionality(client->adapter,
|
||||
I2C_FUNC_SMBUS_WORD_DATA)) {
|
||||
dev_err(dev,
|
||||
"adapter doesn't support SMBus word transactions\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
tmp108 = devm_kzalloc(dev, sizeof(*tmp108), GFP_KERNEL);
|
||||
if (!tmp108)
|
||||
return -ENOMEM;
|
||||
|
||||
dev_set_drvdata(dev, tmp108);
|
||||
|
||||
tmp108->regmap = devm_regmap_init_i2c(client, &tmp108_regmap_config);
|
||||
if (IS_ERR(tmp108->regmap)) {
|
||||
err = PTR_ERR(tmp108->regmap);
|
||||
dev_err(dev, "regmap init failed: %d", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
err = regmap_read(tmp108->regmap, TMP108_REG_CONF, &config);
|
||||
if (err < 0) {
|
||||
dev_err(dev, "error reading config register: %d", err);
|
||||
return err;
|
||||
}
|
||||
tmp108->orig_config = config;
|
||||
|
||||
/* Only continuous mode is supported. */
|
||||
config &= ~TMP108_CONF_MODE_MASK;
|
||||
config |= TMP108_MODE_CONTINUOUS;
|
||||
|
||||
/* Only comparator mode is supported. */
|
||||
config &= ~TMP108_CONF_TM;
|
||||
|
||||
err = regmap_write(tmp108->regmap, TMP108_REG_CONF, config);
|
||||
if (err < 0) {
|
||||
dev_err(dev, "error writing config register: %d", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
tmp108->ready_time = jiffies;
|
||||
if ((tmp108->orig_config & TMP108_CONF_MODE_MASK) ==
|
||||
TMP108_MODE_SHUTDOWN)
|
||||
tmp108->ready_time +=
|
||||
msecs_to_jiffies(TMP108_CONVERSION_TIME_MS);
|
||||
|
||||
err = devm_add_action_or_reset(dev, tmp108_restore_config, tmp108);
|
||||
if (err) {
|
||||
dev_err(dev, "add action or reset failed: %d", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
|
||||
tmp108,
|
||||
&tmp108_chip_info,
|
||||
NULL);
|
||||
return PTR_ERR_OR_ZERO(hwmon_dev);
|
||||
}
|
||||
|
||||
static int __maybe_unused tmp108_suspend(struct device *dev)
|
||||
{
|
||||
struct tmp108 *tmp108 = dev_get_drvdata(dev);
|
||||
|
||||
return regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
|
||||
TMP108_CONF_MODE_MASK, TMP108_MODE_SHUTDOWN);
|
||||
}
|
||||
|
||||
static int __maybe_unused tmp108_resume(struct device *dev)
|
||||
{
|
||||
struct tmp108 *tmp108 = dev_get_drvdata(dev);
|
||||
int err;
|
||||
|
||||
err = regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
|
||||
TMP108_CONF_MODE_MASK, TMP108_MODE_CONTINUOUS);
|
||||
tmp108->ready_time = jiffies +
|
||||
msecs_to_jiffies(TMP108_CONVERSION_TIME_MS);
|
||||
return err;
|
||||
}
|
||||
|
||||
static SIMPLE_DEV_PM_OPS(tmp108_dev_pm_ops, tmp108_suspend, tmp108_resume);
|
||||
|
||||
static const struct i2c_device_id tmp108_i2c_ids[] = {
|
||||
{ "tmp108", 0 },
|
||||
{ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, tmp108_i2c_ids);
|
||||
|
||||
#ifdef CONFIG_OF
|
||||
static const struct of_device_id tmp108_of_ids[] = {
|
||||
{ .compatible = "ti,tmp108", },
|
||||
{}
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, tmp108_of_ids);
|
||||
#endif
|
||||
|
||||
static struct i2c_driver tmp108_driver = {
|
||||
.driver = {
|
||||
.name = DRIVER_NAME,
|
||||
.pm = &tmp108_dev_pm_ops,
|
||||
.of_match_table = of_match_ptr(tmp108_of_ids),
|
||||
},
|
||||
.probe = tmp108_probe,
|
||||
.id_table = tmp108_i2c_ids,
|
||||
};
|
||||
|
||||
module_i2c_driver(tmp108_driver);
|
||||
|
||||
MODULE_AUTHOR("John Muir <john@jmuir.com>");
|
||||
MODULE_DESCRIPTION("Texas Instruments TMP108 temperature sensor driver");
|
||||
MODULE_LICENSE("GPL");
|
Loading…
Reference in a new issue