Merge 4.18-rc7 into driver-core-next
We need the driver core changes in here as well for testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
commit
d2fc88a61b
|
@ -4855,3 +4855,8 @@
|
|||
xirc2ps_cs= [NET,PCMCIA]
|
||||
Format:
|
||||
<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
|
||||
|
||||
xhci-hcd.quirks [USB,KNL]
|
||||
A hex value specifying bitmask with supplemental xhci
|
||||
host controller quirks. Meaning of each bit can be
|
||||
consulted in header drivers/usb/host/xhci.h.
|
||||
|
|
|
@ -324,8 +324,7 @@ Global Attributes
|
|||
|
||||
``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
|
||||
control its functionality at the system level. They are located in the
|
||||
``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
|
||||
CPUs.
|
||||
``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
|
||||
|
||||
Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
|
||||
argument is passed to the kernel in the command line.
|
||||
|
@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
|
|||
but it affects the maximum possible value of per-policy P-state limits
|
||||
(see `Interpretation of Policy Attributes`_ below for details).
|
||||
|
||||
``hwp_dynamic_boost``
|
||||
This attribute is only present if ``intel_pstate`` works in the
|
||||
`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
|
||||
the processor. If set (equal to 1), it causes the minimum P-state limit
|
||||
to be increased dynamically for a short time whenever a task previously
|
||||
waiting on I/O is selected to run on a given logical CPU (the purpose
|
||||
of this mechanism is to improve performance).
|
||||
|
||||
This setting has no effect on logical CPUs whose minimum P-state limit
|
||||
is directly set to the highest non-turbo P-state or above it.
|
||||
|
||||
.. _status_attr:
|
||||
|
||||
``status``
|
||||
|
|
|
@ -15,6 +15,8 @@ Constructor parameters:
|
|||
size)
|
||||
5. the number of optional parameters (the parameters with an argument
|
||||
count as two)
|
||||
start_sector n (default: 0)
|
||||
offset from the start of cache device in 512-byte sectors
|
||||
high_watermark n (default: 50)
|
||||
start writeback when the number of used blocks reach this
|
||||
watermark
|
||||
|
|
|
@ -66,7 +66,7 @@ Required root node properties:
|
|||
- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
|
||||
Octa board.
|
||||
- "insignal,origen" - for Exynos4210-based Insignal Origen board.
|
||||
- "insignal,origen4412 - for Exynos4412-based Insignal Origen board.
|
||||
- "insignal,origen4412" - for Exynos4412-based Insignal Origen board.
|
||||
|
||||
|
||||
Optional nodes:
|
||||
|
|
|
@ -36,7 +36,7 @@ Optional nodes:
|
|||
|
||||
- port/ports: to describe a connection to an external encoder. The
|
||||
binding follows Documentation/devicetree/bindings/graph.txt and
|
||||
suppors a single port with a single endpoint.
|
||||
supports a single port with a single endpoint.
|
||||
|
||||
- See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
|
||||
Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting
|
||||
|
|
|
@ -1,7 +1,7 @@
|
|||
Nintendo Wii (Hollywood) GPIO controller
|
||||
|
||||
Required properties:
|
||||
- compatible: "nintendo,hollywood-gpio
|
||||
- compatible: "nintendo,hollywood-gpio"
|
||||
- reg: Physical base address and length of the controller's registers.
|
||||
- gpio-controller: Marks the device node as a GPIO controller.
|
||||
- #gpio-cells: Should be <2>. The first cell is the pin number and the
|
||||
|
|
|
@ -0,0 +1,23 @@
|
|||
Spreadtrum SC27xx PMIC Vibrator
|
||||
|
||||
Required properties:
|
||||
- compatible: should be "sprd,sc2731-vibrator".
|
||||
- reg: address of vibrator control register.
|
||||
|
||||
Example :
|
||||
|
||||
sc2731_pmic: pmic@0 {
|
||||
compatible = "sprd,sc2731";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <26000000>;
|
||||
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
vibrator@eb4 {
|
||||
compatible = "sprd,sc2731-vibrator";
|
||||
reg = <0xeb4>;
|
||||
};
|
||||
};
|
|
@ -32,7 +32,7 @@ i2c@00000000 {
|
|||
reg = <0x6c>;
|
||||
interrupt-parent = <&gpx1>;
|
||||
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
||||
vdd-supply = <&ldo15_reg>";
|
||||
vdd-supply = <&ldo15_reg>;
|
||||
vid-supply = <&ldo18_reg>;
|
||||
reset-gpios = <&gpx1 5 0>;
|
||||
touchscreen-size-x = <1080>;
|
||||
|
|
|
@ -15,7 +15,7 @@ Required properties:
|
|||
include "nvidia,tegra30-ictlr".
|
||||
- reg : Specifies base physical address and size of the registers.
|
||||
Each controller must be described separately (Tegra20 has 4 of them,
|
||||
whereas Tegra30 and later have 5"
|
||||
whereas Tegra30 and later have 5).
|
||||
- interrupt-controller : Identifies the node as an interrupt controller.
|
||||
- #interrupt-cells : Specifies the number of cells needed to encode an
|
||||
interrupt source. The value must be 3.
|
||||
|
|
|
@ -12,7 +12,7 @@ Required properties:
|
|||
specifier, shall be 2
|
||||
- interrupts: interrupts references to primary interrupt controller
|
||||
(only needed for exti controller with multiple exti under
|
||||
same parent interrupt: st,stm32-exti and st,stm32h7-exti")
|
||||
same parent interrupt: st,stm32-exti and st,stm32h7-exti)
|
||||
|
||||
Example:
|
||||
|
||||
|
|
|
@ -152,7 +152,7 @@ Required properties:
|
|||
- compatible : should contain one of:
|
||||
"brcm,bcm7425-timers"
|
||||
"brcm,bcm7429-timers"
|
||||
"brcm,bcm7435-timers and
|
||||
"brcm,bcm7435-timers" and
|
||||
"brcm,brcmstb-timers"
|
||||
- reg : the timers register range
|
||||
- interrupts : the interrupt line for this timer block
|
||||
|
|
|
@ -238,7 +238,7 @@ PROPERTIES
|
|||
Must include one of the following:
|
||||
- "fsl,fman-dtsec" for dTSEC MAC
|
||||
- "fsl,fman-xgec" for XGEC MAC
|
||||
- "fsl,fman-memac for mEMAC MAC
|
||||
- "fsl,fman-memac" for mEMAC MAC
|
||||
|
||||
- cell-index
|
||||
Usage: required
|
||||
|
|
|
@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
|
|||
node with the label "power".
|
||||
In the second example the consumer device are partitioned across two PM domains,
|
||||
the first with index 0 and the second with index 1, of a power controller that
|
||||
is represented by a node with the label "power.
|
||||
is represented by a node with the label "power".
|
||||
|
||||
Optional properties:
|
||||
- required-opps: This contains phandle to an OPP node in another device's OPP
|
||||
|
|
|
@ -16,7 +16,7 @@ Required properties:
|
|||
Optional properties:
|
||||
- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
If DCDCs are externally controlled then this property should be there.
|
||||
- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
|
||||
If DCDCs are externally controlled and if it is from GPIO then GPIO
|
||||
number should be provided. If it is externally controlled and no GPIO
|
||||
entry then driver will just configure this rails as external control
|
||||
|
|
|
@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
|
|||
controller binding usage.
|
||||
|
||||
Required properties:
|
||||
- compatible: Should be st,stih407-softreset";
|
||||
- compatible: Should be "st,stih407-softreset";
|
||||
- #reset-cells: 1, see below
|
||||
|
||||
example:
|
||||
|
|
|
@ -39,7 +39,7 @@ Required properties:
|
|||
|
||||
Optional property:
|
||||
- clock-frequency: Desired I2C bus clock frequency in Hz.
|
||||
When missing default to 400000Hz.
|
||||
When missing default to 100000Hz.
|
||||
|
||||
Child nodes should conform to I2C bus binding as described in i2c.txt.
|
||||
|
||||
|
|
|
@ -30,7 +30,7 @@ Required properties:
|
|||
|
||||
Board connectors:
|
||||
* Headset Mic
|
||||
* Secondary Mic",
|
||||
* Secondary Mic
|
||||
* DMIC
|
||||
* Ext Spk
|
||||
|
||||
|
|
|
@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
|
|||
"Digital Mic3"
|
||||
|
||||
Audio pins and MicBias on WCD9335 Codec:
|
||||
"MIC_BIAS1
|
||||
"MIC_BIAS1"
|
||||
"MIC_BIAS2"
|
||||
"MIC_BIAS3"
|
||||
"MIC_BIAS4"
|
||||
|
|
|
@ -16,7 +16,8 @@ A child node must exist to represent the core DWC3 IP block. The name of
|
|||
the node is not important. The content of the node is defined in dwc3.txt.
|
||||
|
||||
Phy documentation is provided in the following places:
|
||||
Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
|
||||
Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY
|
||||
Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY
|
||||
|
||||
Example device nodes:
|
||||
|
||||
|
|
|
@ -15,7 +15,7 @@ Optional properties:
|
|||
|
||||
Examples:
|
||||
|
||||
onewire@0 {
|
||||
onewire {
|
||||
compatible = "w1-gpio";
|
||||
gpios = <&gpio 126 0>, <&gpio 105 0>;
|
||||
};
|
||||
|
|
|
@ -441,8 +441,6 @@ prototypes:
|
|||
int (*iterate) (struct file *, struct dir_context *);
|
||||
int (*iterate_shared) (struct file *, struct dir_context *);
|
||||
__poll_t (*poll) (struct file *, struct poll_table_struct *);
|
||||
struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
|
||||
__poll_t (*poll_mask) (struct file *, __poll_t);
|
||||
long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
|
||||
long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
|
||||
int (*mmap) (struct file *, struct vm_area_struct *);
|
||||
|
@ -473,7 +471,7 @@ prototypes:
|
|||
};
|
||||
|
||||
locking rules:
|
||||
All except for ->poll_mask may block.
|
||||
All may block.
|
||||
|
||||
->llseek() locking has moved from llseek to the individual llseek
|
||||
implementations. If your fs is not using generic_file_llseek, you
|
||||
|
@ -505,9 +503,6 @@ in sys_read() and friends.
|
|||
the lease within the individual filesystem to record the result of the
|
||||
operation
|
||||
|
||||
->poll_mask can be called with or without the waitqueue lock for the waitqueue
|
||||
returned from ->get_poll_head.
|
||||
|
||||
--------------------------- dquot_operations -------------------------------
|
||||
prototypes:
|
||||
int (*write_dquot) (struct dquot *);
|
||||
|
|
|
@ -857,8 +857,6 @@ struct file_operations {
|
|||
ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
|
||||
int (*iterate) (struct file *, struct dir_context *);
|
||||
__poll_t (*poll) (struct file *, struct poll_table_struct *);
|
||||
struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
|
||||
__poll_t (*poll_mask) (struct file *, __poll_t);
|
||||
long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
|
||||
long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
|
||||
int (*mmap) (struct file *, struct vm_area_struct *);
|
||||
|
@ -903,17 +901,6 @@ otherwise noted.
|
|||
activity on this file and (optionally) go to sleep until there
|
||||
is activity. Called by the select(2) and poll(2) system calls
|
||||
|
||||
get_poll_head: Returns the struct wait_queue_head that callers can
|
||||
wait on. Callers need to check the returned events using ->poll_mask
|
||||
once woken. Can return NULL to indicate polling is not supported,
|
||||
or any error code using the ERR_PTR convention to indicate that a
|
||||
grave error occured and ->poll_mask shall not be called.
|
||||
|
||||
poll_mask: return the mask of EPOLL* values describing the file descriptor
|
||||
state. Called either before going to sleep on the waitqueue returned by
|
||||
get_poll_head, or after it has been woken. If ->get_poll_head and
|
||||
->poll_mask are implemented ->poll does not need to be implement.
|
||||
|
||||
unlocked_ioctl: called by the ioctl(2) system call.
|
||||
|
||||
compat_ioctl: called by the ioctl(2) system call when 32 bit system calls
|
||||
|
|
|
@ -50,6 +50,11 @@ LDFLAGS_MODULE
|
|||
--------------------------------------------------
|
||||
Additional options used for $(LD) when linking modules.
|
||||
|
||||
KBUILD_KCONFIG
|
||||
--------------------------------------------------
|
||||
Set the top-level Kconfig file to the value of this environment
|
||||
variable. The default name is "Kconfig".
|
||||
|
||||
KBUILD_VERBOSE
|
||||
--------------------------------------------------
|
||||
Set the kbuild verbosity. Can be assigned same values as "V=...".
|
||||
|
@ -88,7 +93,8 @@ In most cases the name of the architecture is the same as the
|
|||
directory name found in the arch/ directory.
|
||||
But some architectures such as x86 and sparc have aliases.
|
||||
x86: i386 for 32 bit, x86_64 for 64 bit
|
||||
sparc: sparc for 32 bit, sparc64 for 64 bit
|
||||
sh: sh for 32 bit, sh64 for 64 bit
|
||||
sparc: sparc32 for 32 bit, sparc64 for 64 bit
|
||||
|
||||
CROSS_COMPILE
|
||||
--------------------------------------------------
|
||||
|
@ -148,15 +154,6 @@ stripped after they are installed. If INSTALL_MOD_STRIP is '1', then
|
|||
the default option --strip-debug will be used. Otherwise,
|
||||
INSTALL_MOD_STRIP value will be used as the options to the strip command.
|
||||
|
||||
INSTALL_FW_PATH
|
||||
--------------------------------------------------
|
||||
INSTALL_FW_PATH specifies where to install the firmware blobs.
|
||||
The default value is:
|
||||
|
||||
$(INSTALL_MOD_PATH)/lib/firmware
|
||||
|
||||
The value can be overridden in which case the default value is ignored.
|
||||
|
||||
INSTALL_HDR_PATH
|
||||
--------------------------------------------------
|
||||
INSTALL_HDR_PATH specifies where to install user space headers when
|
||||
|
|
|
@ -430,6 +430,12 @@ This sets the config program's title bar if the config program chooses
|
|||
to use it. It should be placed at the top of the configuration, before any
|
||||
other statement.
|
||||
|
||||
'#' Kconfig source file comment:
|
||||
|
||||
An unquoted '#' character anywhere in a source file line indicates
|
||||
the beginning of a source file comment. The remainder of that line
|
||||
is a comment.
|
||||
|
||||
|
||||
Kconfig hints
|
||||
-------------
|
||||
|
|
|
@ -2,9 +2,9 @@ This file contains some assistance for using "make *config".
|
|||
|
||||
Use "make help" to list all of the possible configuration targets.
|
||||
|
||||
The xconfig ('qconf') and menuconfig ('mconf') programs also
|
||||
have embedded help text. Be sure to check it for navigation,
|
||||
search, and other general help text.
|
||||
The xconfig ('qconf'), menuconfig ('mconf'), and nconfig ('nconf')
|
||||
programs also have embedded help text. Be sure to check that for
|
||||
navigation, search, and other general help text.
|
||||
|
||||
======================================================================
|
||||
General
|
||||
|
@ -17,13 +17,16 @@ this happens, using a previously working .config file and running
|
|||
for you, so you may find that you need to see what NEW kernel
|
||||
symbols have been introduced.
|
||||
|
||||
To see a list of new config symbols when using "make oldconfig", use
|
||||
To see a list of new config symbols, use
|
||||
|
||||
cp user/some/old.config .config
|
||||
make listnewconfig
|
||||
|
||||
and the config program will list any new symbols, one per line.
|
||||
|
||||
Alternatively, you can use the brute force method:
|
||||
|
||||
make oldconfig
|
||||
scripts/diffconfig .config.old .config | less
|
||||
|
||||
______________________________________________________________________
|
||||
|
@ -160,7 +163,7 @@ Searching in menuconfig:
|
|||
This lists all config symbols that contain "hotplug",
|
||||
e.g., HOTPLUG_CPU, MEMORY_HOTPLUG.
|
||||
|
||||
For search help, enter / followed TAB-TAB-TAB (to highlight
|
||||
For search help, enter / followed by TAB-TAB (to highlight
|
||||
<Help>) and Enter. This will tell you that you can also use
|
||||
regular expressions (regexes) in the search string, so if you
|
||||
are not interested in MEMORY_HOTPLUG, you could try
|
||||
|
@ -202,6 +205,39 @@ Example:
|
|||
make MENUCONFIG_MODE=single_menu menuconfig
|
||||
|
||||
|
||||
======================================================================
|
||||
nconfig
|
||||
--------------------------------------------------
|
||||
|
||||
nconfig is an alternate text-based configurator. It lists function
|
||||
keys across the bottom of the terminal (window) that execute commands.
|
||||
You can also just use the corresponding numeric key to execute the
|
||||
commands unless you are in a data entry window. E.g., instead of F6
|
||||
for Save, you can just press 6.
|
||||
|
||||
Use F1 for Global help or F3 for the Short help menu.
|
||||
|
||||
Searching in nconfig:
|
||||
|
||||
You can search either in the menu entry "prompt" strings
|
||||
or in the configuration symbols.
|
||||
|
||||
Use / to begin a search through the menu entries. This does
|
||||
not support regular expressions. Use <Down> or <Up> for
|
||||
Next hit and Previous hit, respectively. Use <Esc> to
|
||||
terminate the search mode.
|
||||
|
||||
F8 (SymSearch) searches the configuration symbols for the
|
||||
given string or regular expression (regex).
|
||||
|
||||
NCONFIG_MODE
|
||||
--------------------------------------------------
|
||||
This mode shows all sub-menus in one large tree.
|
||||
|
||||
Example:
|
||||
make NCONFIG_MODE=single_menu nconfig
|
||||
|
||||
|
||||
======================================================================
|
||||
xconfig
|
||||
--------------------------------------------------
|
||||
|
@ -230,8 +266,7 @@ gconfig
|
|||
|
||||
Searching in gconfig:
|
||||
|
||||
None (gconfig isn't maintained as well as xconfig or menuconfig);
|
||||
however, gconfig does have a few more viewing choices than
|
||||
xconfig does.
|
||||
There is no search command in gconfig. However, gconfig does
|
||||
have several different viewing choices, modes, and options.
|
||||
|
||||
###
|
||||
|
|
|
@ -1490,7 +1490,7 @@ To remove an ARP target:
|
|||
|
||||
To configure the interval between learning packet transmits:
|
||||
# echo 12 > /sys/class/net/bond0/bonding/lp_interval
|
||||
NOTE: the lp_inteval is the number of seconds between instances where
|
||||
NOTE: the lp_interval is the number of seconds between instances where
|
||||
the bonding driver sends learning packets to each slaves peer switch. The
|
||||
default interval is 1 second.
|
||||
|
||||
|
|
|
@ -1,3 +1,4 @@
|
|||
==============================================================
|
||||
Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
|
||||
==============================================================
|
||||
|
||||
|
@ -46,123 +47,131 @@ Driver Configuration Parameters
|
|||
The default value for each parameter is generally the recommended setting,
|
||||
unless otherwise noted.
|
||||
|
||||
Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
|
||||
Rx Descriptors:
|
||||
Number of receive descriptors. A receive descriptor is a data
|
||||
structure that describes a receive buffer and its attributes to the network
|
||||
controller. The data in the descriptor is used by the controller to write
|
||||
data from the controller to host memory. In the 3.x.x driver the valid range
|
||||
for this parameter is 64-256. The default value is 256. This parameter can be
|
||||
changed using the command::
|
||||
|
||||
ethtool -G eth? rx n
|
||||
ethtool -G eth? rx n
|
||||
|
||||
Where n is the number of desired Rx descriptors.
|
||||
|
||||
Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
|
||||
Tx Descriptors:
|
||||
Number of transmit descriptors. A transmit descriptor is a data
|
||||
structure that describes a transmit buffer and its attributes to the network
|
||||
controller. The data in the descriptor is used by the controller to read
|
||||
data from the host memory to the controller. In the 3.x.x driver the valid
|
||||
range for this parameter is 64-256. The default value is 128. This parameter
|
||||
can be changed using the command::
|
||||
|
||||
ethtool -G eth? tx n
|
||||
ethtool -G eth? tx n
|
||||
|
||||
Where n is the number of desired Tx descriptors.
|
||||
|
||||
Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
|
||||
Speed/Duplex:
|
||||
The driver auto-negotiates the link speed and duplex settings by
|
||||
default. The ethtool utility can be used as follows to force speed/duplex.::
|
||||
|
||||
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
|
||||
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
|
||||
|
||||
NOTE: setting the speed/duplex to incorrect values will cause the link to
|
||||
fail.
|
||||
|
||||
Event Log Message Level: The driver uses the message level flag to log events
|
||||
Event Log Message Level:
|
||||
The driver uses the message level flag to log events
|
||||
to syslog. The message level can be set at driver load time. It can also be
|
||||
set using the command::
|
||||
|
||||
ethtool -s eth? msglvl n
|
||||
ethtool -s eth? msglvl n
|
||||
|
||||
|
||||
Additional Configurations
|
||||
=========================
|
||||
|
||||
Configuring the Driver on Different Distributions
|
||||
-------------------------------------------------
|
||||
Configuring the Driver on Different Distributions
|
||||
-------------------------------------------------
|
||||
|
||||
Configuring a network driver to load properly when the system is started is
|
||||
distribution dependent. Typically, the configuration process involves adding
|
||||
an alias line to /etc/modprobe.d/*.conf as well as editing other system
|
||||
startup scripts and/or configuration files. Many popular Linux
|
||||
distributions ship with tools to make these changes for you. To learn the
|
||||
proper way to configure a network device for your system, refer to your
|
||||
distribution documentation. If during this process you are asked for the
|
||||
driver or module name, the name for the Linux Base Driver for the Intel
|
||||
PRO/100 Family of Adapters is e100.
|
||||
Configuring a network driver to load properly when the system is started
|
||||
is distribution dependent. Typically, the configuration process involves
|
||||
adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other
|
||||
system startup scripts and/or configuration files. Many popular Linux
|
||||
distributions ship with tools to make these changes for you. To learn
|
||||
the proper way to configure a network device for your system, refer to
|
||||
your distribution documentation. If during this process you are asked
|
||||
for the driver or module name, the name for the Linux Base Driver for
|
||||
the Intel PRO/100 Family of Adapters is e100.
|
||||
|
||||
As an example, if you install the e100 driver for two PRO/100 adapters
|
||||
(eth0 and eth1), add the following to a configuration file in /etc/modprobe.d/
|
||||
As an example, if you install the e100 driver for two PRO/100 adapters
|
||||
(eth0 and eth1), add the following to a configuration file in
|
||||
/etc/modprobe.d/::
|
||||
|
||||
alias eth0 e100
|
||||
alias eth1 e100
|
||||
|
||||
Viewing Link Messages
|
||||
---------------------
|
||||
In order to see link messages and other Intel driver information on your
|
||||
console, you must set the dmesg level up to six. This can be done by
|
||||
entering the following on the command line before loading the e100 driver::
|
||||
Viewing Link Messages
|
||||
---------------------
|
||||
|
||||
In order to see link messages and other Intel driver information on your
|
||||
console, you must set the dmesg level up to six. This can be done by
|
||||
entering the following on the command line before loading the e100
|
||||
driver::
|
||||
|
||||
dmesg -n 6
|
||||
|
||||
If you wish to see all messages issued by the driver, including debug
|
||||
messages, set the dmesg level to eight.
|
||||
If you wish to see all messages issued by the driver, including debug
|
||||
messages, set the dmesg level to eight.
|
||||
|
||||
NOTE: This setting is not saved across reboots.
|
||||
NOTE: This setting is not saved across reboots.
|
||||
|
||||
ethtool
|
||||
-------
|
||||
|
||||
ethtool
|
||||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
The latest release of ethtool can be found from
|
||||
https://www.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
The latest release of ethtool can be found from
|
||||
https://www.kernel.org/pub/software/network/ethtool/
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is provided through the ethtool* utility. For instructions on
|
||||
enabling WoL with ethtool, refer to the ethtool man page. WoL will be
|
||||
enabled on the system during the next shut down or reboot. For this
|
||||
driver version, in order to enable WoL, the e100 driver must be loaded
|
||||
when shutting down or rebooting the system.
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is provided through the ethtool* utility. For instructions on enabling
|
||||
WoL with ethtool, refer to the ethtool man page.
|
||||
NAPI
|
||||
----
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot. For
|
||||
this driver version, in order to enable WoL, the e100 driver must be
|
||||
loaded when shutting down or rebooting the system.
|
||||
NAPI (Rx polling mode) is supported in the e100 driver.
|
||||
|
||||
NAPI
|
||||
----
|
||||
See https://wiki.linuxfoundation.org/networking/napi for more
|
||||
information on NAPI.
|
||||
|
||||
NAPI (Rx polling mode) is supported in the e100 driver.
|
||||
Multiple Interfaces on Same Ethernet Broadcast Network
|
||||
------------------------------------------------------
|
||||
|
||||
See https://wiki.linuxfoundation.org/networking/napi for more information
|
||||
on NAPI.
|
||||
Due to the default ARP behavior on Linux, it is not possible to have one
|
||||
system on two IP networks in the same Ethernet broadcast domain
|
||||
(non-partitioned switch) behave as expected. All Ethernet interfaces
|
||||
will respond to IP traffic for any IP address assigned to the system.
|
||||
This results in unbalanced receive traffic.
|
||||
|
||||
Multiple Interfaces on Same Ethernet Broadcast Network
|
||||
------------------------------------------------------
|
||||
If you have multiple interfaces in a server, either turn on ARP
|
||||
filtering by
|
||||
|
||||
Due to the default ARP behavior on Linux, it is not possible to have
|
||||
one system on two IP networks in the same Ethernet broadcast domain
|
||||
(non-partitioned switch) behave as expected. All Ethernet interfaces
|
||||
will respond to IP traffic for any IP address assigned to the system.
|
||||
This results in unbalanced receive traffic.
|
||||
(1) entering::
|
||||
|
||||
If you have multiple interfaces in a server, either turn on ARP
|
||||
filtering by
|
||||
echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
|
||||
|
||||
(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
|
||||
(this only works if your kernel's version is higher than 2.4.5), or
|
||||
(this only works if your kernel's version is higher than 2.4.5), or
|
||||
|
||||
(2) installing the interfaces in separate broadcast domains (either
|
||||
in different switches or in a switch partitioned to VLANs).
|
||||
(2) installing the interfaces in separate broadcast domains (either
|
||||
in different switches or in a switch partitioned to VLANs).
|
||||
|
||||
|
||||
Support
|
||||
|
|
|
@ -1,3 +1,4 @@
|
|||
===========================================================
|
||||
Linux* Base Driver for Intel(R) Ethernet Network Connection
|
||||
===========================================================
|
||||
|
||||
|
@ -33,7 +34,8 @@ Command Line Parameters
|
|||
The default value for each parameter is generally the recommended setting,
|
||||
unless otherwise noted.
|
||||
|
||||
NOTES: For more information about the AutoNeg, Duplex, and Speed
|
||||
NOTES:
|
||||
For more information about the AutoNeg, Duplex, and Speed
|
||||
parameters, see the "Speed and Duplex Configuration" section in
|
||||
this document.
|
||||
|
||||
|
@ -44,22 +46,27 @@ NOTES: For more information about the AutoNeg, Duplex, and Speed
|
|||
|
||||
AutoNeg
|
||||
-------
|
||||
|
||||
(Supported only on adapters with copper connections)
|
||||
Valid Range: 0x01-0x0F, 0x20-0x2F
|
||||
Default Value: 0x2F
|
||||
|
||||
:Valid Range: 0x01-0x0F, 0x20-0x2F
|
||||
:Default Value: 0x2F
|
||||
|
||||
This parameter is a bit-mask that specifies the speed and duplex settings
|
||||
advertised by the adapter. When this parameter is used, the Speed and
|
||||
Duplex parameters must not be specified.
|
||||
|
||||
NOTE: Refer to the Speed and Duplex section of this readme for more
|
||||
NOTE:
|
||||
Refer to the Speed and Duplex section of this readme for more
|
||||
information on the AutoNeg parameter.
|
||||
|
||||
Duplex
|
||||
------
|
||||
|
||||
(Supported only on adapters with copper connections)
|
||||
Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
|
||||
Default Value: 0
|
||||
|
||||
:Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
|
||||
:Default Value: 0
|
||||
|
||||
This defines the direction in which data is allowed to flow. Can be
|
||||
either one or two-directional. If both Duplex and the link partner are
|
||||
|
@ -69,18 +76,22 @@ duplex.
|
|||
|
||||
FlowControl
|
||||
-----------
|
||||
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
|
||||
Default Value: Reads flow control settings from the EEPROM
|
||||
|
||||
:Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
|
||||
:Default Value: Reads flow control settings from the EEPROM
|
||||
|
||||
This parameter controls the automatic generation(Tx) and response(Rx)
|
||||
to Ethernet PAUSE frames.
|
||||
|
||||
InterruptThrottleRate
|
||||
---------------------
|
||||
|
||||
(not supported on Intel(R) 82542, 82543 or 82544-based adapters)
|
||||
Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
|
||||
4=simplified balancing)
|
||||
Default Value: 3
|
||||
|
||||
:Valid Range:
|
||||
0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
|
||||
4=simplified balancing)
|
||||
:Default Value: 3
|
||||
|
||||
The driver can limit the amount of interrupts per second that the adapter
|
||||
will generate for incoming packets. It does this by writing a value to the
|
||||
|
@ -134,13 +145,15 @@ Setting InterruptThrottleRate to 0 turns off any interrupt moderation
|
|||
and may improve small packet latency, but is generally not suitable
|
||||
for bulk throughput traffic.
|
||||
|
||||
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
|
||||
NOTE:
|
||||
InterruptThrottleRate takes precedence over the TxAbsIntDelay and
|
||||
RxAbsIntDelay parameters. In other words, minimizing the receive
|
||||
and/or transmit absolute delays does not force the controller to
|
||||
generate more interrupts than what the Interrupt Throttle Rate
|
||||
allows.
|
||||
|
||||
CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection
|
||||
CAUTION:
|
||||
If you are using the Intel(R) PRO/1000 CT Network Connection
|
||||
(controller 82547), setting InterruptThrottleRate to a value
|
||||
greater than 75,000, may hang (stop transmitting) adapters
|
||||
under certain network conditions. If this occurs a NETDEV
|
||||
|
@ -150,7 +163,8 @@ CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection
|
|||
hang, ensure that InterruptThrottleRate is set no greater
|
||||
than 75,000 and is not set to 0.
|
||||
|
||||
NOTE: When e1000 is loaded with default settings and multiple adapters
|
||||
NOTE:
|
||||
When e1000 is loaded with default settings and multiple adapters
|
||||
are in use simultaneously, the CPU utilization may increase non-
|
||||
linearly. In order to limit the CPU utilization without impacting
|
||||
the overall throughput, we recommend that you load the driver as
|
||||
|
@ -167,9 +181,11 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
|
|||
|
||||
RxDescriptors
|
||||
-------------
|
||||
Valid Range: 48-256 for 82542 and 82543-based adapters
|
||||
48-4096 for all other supported adapters
|
||||
Default Value: 256
|
||||
|
||||
:Valid Range:
|
||||
- 48-256 for 82542 and 82543-based adapters
|
||||
- 48-4096 for all other supported adapters
|
||||
:Default Value: 256
|
||||
|
||||
This value specifies the number of receive buffer descriptors allocated
|
||||
by the driver. Increasing this value allows the driver to buffer more
|
||||
|
@ -179,15 +195,17 @@ Each descriptor is 16 bytes. A receive buffer is also allocated for each
|
|||
descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
|
||||
on the MTU setting. The maximum MTU size is 16110.
|
||||
|
||||
NOTE: MTU designates the frame size. It only needs to be set for Jumbo
|
||||
NOTE:
|
||||
MTU designates the frame size. It only needs to be set for Jumbo
|
||||
Frames. Depending on the available system resources, the request
|
||||
for a higher number of receive descriptors may be denied. In this
|
||||
case, use a lower number.
|
||||
|
||||
RxIntDelay
|
||||
----------
|
||||
Valid Range: 0-65535 (0=off)
|
||||
Default Value: 0
|
||||
|
||||
:Valid Range: 0-65535 (0=off)
|
||||
:Default Value: 0
|
||||
|
||||
This value delays the generation of receive interrupts in units of 1.024
|
||||
microseconds. Receive interrupt reduction can improve CPU efficiency if
|
||||
|
@ -197,7 +215,8 @@ of TCP traffic. If the system is reporting dropped receives, this value
|
|||
may be set too high, causing the driver to run out of available receive
|
||||
descriptors.
|
||||
|
||||
CAUTION: When setting RxIntDelay to a value other than 0, adapters may
|
||||
CAUTION:
|
||||
When setting RxIntDelay to a value other than 0, adapters may
|
||||
hang (stop transmitting) under certain network conditions. If
|
||||
this occurs a NETDEV WATCHDOG message is logged in the system
|
||||
event log. In addition, the controller is automatically reset,
|
||||
|
@ -206,9 +225,11 @@ CAUTION: When setting RxIntDelay to a value other than 0, adapters may
|
|||
|
||||
RxAbsIntDelay
|
||||
-------------
|
||||
|
||||
(This parameter is supported only on 82540, 82545 and later adapters.)
|
||||
Valid Range: 0-65535 (0=off)
|
||||
Default Value: 128
|
||||
|
||||
:Valid Range: 0-65535 (0=off)
|
||||
:Default Value: 128
|
||||
|
||||
This value, in units of 1.024 microseconds, limits the delay in which a
|
||||
receive interrupt is generated. Useful only if RxIntDelay is non-zero,
|
||||
|
@ -219,9 +240,11 @@ conditions.
|
|||
|
||||
Speed
|
||||
-----
|
||||
|
||||
(This parameter is supported only on adapters with copper connections.)
|
||||
Valid Settings: 0, 10, 100, 1000
|
||||
Default Value: 0 (auto-negotiate at all supported speeds)
|
||||
|
||||
:Valid Settings: 0, 10, 100, 1000
|
||||
:Default Value: 0 (auto-negotiate at all supported speeds)
|
||||
|
||||
Speed forces the line speed to the specified value in megabits per second
|
||||
(Mbps). If this parameter is not specified or is set to 0 and the link
|
||||
|
@ -230,22 +253,26 @@ speed. Duplex should also be set when Speed is set to either 10 or 100.
|
|||
|
||||
TxDescriptors
|
||||
-------------
|
||||
Valid Range: 48-256 for 82542 and 82543-based adapters
|
||||
48-4096 for all other supported adapters
|
||||
Default Value: 256
|
||||
|
||||
:Valid Range:
|
||||
- 48-256 for 82542 and 82543-based adapters
|
||||
- 48-4096 for all other supported adapters
|
||||
:Default Value: 256
|
||||
|
||||
This value is the number of transmit descriptors allocated by the driver.
|
||||
Increasing this value allows the driver to queue more transmits. Each
|
||||
descriptor is 16 bytes.
|
||||
|
||||
NOTE: Depending on the available system resources, the request for a
|
||||
NOTE:
|
||||
Depending on the available system resources, the request for a
|
||||
higher number of transmit descriptors may be denied. In this case,
|
||||
use a lower number.
|
||||
|
||||
TxIntDelay
|
||||
----------
|
||||
Valid Range: 0-65535 (0=off)
|
||||
Default Value: 8
|
||||
|
||||
:Valid Range: 0-65535 (0=off)
|
||||
:Default Value: 8
|
||||
|
||||
This value delays the generation of transmit interrupts in units of
|
||||
1.024 microseconds. Transmit interrupt reduction can improve CPU
|
||||
|
@ -255,9 +282,11 @@ causing the driver to run out of available transmit descriptors.
|
|||
|
||||
TxAbsIntDelay
|
||||
-------------
|
||||
|
||||
(This parameter is supported only on 82540, 82545 and later adapters.)
|
||||
Valid Range: 0-65535 (0=off)
|
||||
Default Value: 32
|
||||
|
||||
:Valid Range: 0-65535 (0=off)
|
||||
:Default Value: 32
|
||||
|
||||
This value, in units of 1.024 microseconds, limits the delay in which a
|
||||
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
|
||||
|
@ -268,18 +297,21 @@ network conditions.
|
|||
|
||||
XsumRX
|
||||
------
|
||||
|
||||
(This parameter is NOT supported on the 82542-based adapter.)
|
||||
Valid Range: 0-1
|
||||
Default Value: 1
|
||||
|
||||
:Valid Range: 0-1
|
||||
:Default Value: 1
|
||||
|
||||
A value of '1' indicates that the driver should enable IP checksum
|
||||
offload for received packets (both UDP and TCP) to the adapter hardware.
|
||||
|
||||
Copybreak
|
||||
---------
|
||||
Valid Range: 0-xxxxxxx (0=off)
|
||||
Default Value: 256
|
||||
Usage: modprobe e1000.ko copybreak=128
|
||||
|
||||
:Valid Range: 0-xxxxxxx (0=off)
|
||||
:Default Value: 256
|
||||
:Usage: modprobe e1000.ko copybreak=128
|
||||
|
||||
Driver copies all packets below or equaling this size to a fresh RX
|
||||
buffer before handing it up the stack.
|
||||
|
@ -291,8 +323,9 @@ it is also available during runtime at
|
|||
|
||||
SmartPowerDownEnable
|
||||
--------------------
|
||||
Valid Range: 0-1
|
||||
Default Value: 0 (disabled)
|
||||
|
||||
:Valid Range: 0-1
|
||||
:Default Value: 0 (disabled)
|
||||
|
||||
Allows PHY to turn off in lower power states. The user can turn off
|
||||
this parameter in supported chipsets.
|
||||
|
@ -308,14 +341,14 @@ fiber interface board only links at 1000 Mbps full-duplex.
|
|||
|
||||
For copper-based boards, the keywords interact as follows:
|
||||
|
||||
The default operation is auto-negotiate. The board advertises all
|
||||
- The default operation is auto-negotiate. The board advertises all
|
||||
supported speed and duplex combinations, and it links at the highest
|
||||
common speed and duplex mode IF the link partner is set to auto-negotiate.
|
||||
|
||||
If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
|
||||
- If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
|
||||
is advertised (The 1000BaseT spec requires auto-negotiation.)
|
||||
|
||||
If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
|
||||
- If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
|
||||
negotiation is disabled, and the AutoNeg parameter is ignored. Partner
|
||||
SHOULD also be forced.
|
||||
|
||||
|
@ -327,13 +360,15 @@ process.
|
|||
The parameter may be specified as either a decimal or hexadecimal value as
|
||||
determined by the bitmap below.
|
||||
|
||||
============== ====== ====== ======= ======= ====== ====== ======= ======
|
||||
Bit position 7 6 5 4 3 2 1 0
|
||||
Decimal Value 128 64 32 16 8 4 2 1
|
||||
Hex value 80 40 20 10 8 4 2 1
|
||||
Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
|
||||
Duplex Full Full Half Full Half
|
||||
============== ====== ====== ======= ======= ====== ====== ======= ======
|
||||
|
||||
Some examples of using AutoNeg:
|
||||
Some examples of using AutoNeg::
|
||||
|
||||
modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
|
||||
modprobe e1000 AutoNeg=1 (Same as above)
|
||||
|
@ -354,8 +389,9 @@ previously mentioned to force the adapter to the same speed and duplex.
|
|||
Additional Configurations
|
||||
=========================
|
||||
|
||||
Jumbo Frames
|
||||
------------
|
||||
Jumbo Frames
|
||||
------------
|
||||
|
||||
Jumbo Frames support is enabled by changing the MTU to a value larger than
|
||||
the default of 1500. Use the ifconfig command to increase the MTU size.
|
||||
For example::
|
||||
|
@ -367,11 +403,11 @@ Additional Configurations
|
|||
|
||||
MTU=9000
|
||||
|
||||
to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
|
||||
applies to the Red Hat distributions; other distributions may store this
|
||||
setting in a different location.
|
||||
to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
|
||||
applies to the Red Hat distributions; other distributions may store this
|
||||
setting in a different location.
|
||||
|
||||
Notes:
|
||||
Notes:
|
||||
Degradation in throughput performance may be observed in some Jumbo frames
|
||||
environments. If this is observed, increasing the application's socket buffer
|
||||
size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
|
||||
|
@ -385,12 +421,14 @@ Additional Configurations
|
|||
poor performance or loss of link.
|
||||
|
||||
- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
|
||||
support Jumbo Frames. These correspond to the following product names:
|
||||
support Jumbo Frames. These correspond to the following product names::
|
||||
|
||||
Intel(R) PRO/1000 Gigabit Server Adapter
|
||||
Intel(R) PRO/1000 PM Network Connection
|
||||
|
||||
ethtool
|
||||
-------
|
||||
ethtool
|
||||
-------
|
||||
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
|
@ -398,8 +436,9 @@ Additional Configurations
|
|||
The latest release of ethtool can be found from
|
||||
https://www.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
|
||||
WoL is configured through the ethtool* utility.
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot.
|
||||
|
|
|
@ -48,7 +48,7 @@ void strp_pause(struct strparser *strp)
|
|||
Temporarily pause a stream parser. Message parsing is suspended
|
||||
and no new messages are delivered to the upper layer.
|
||||
|
||||
void strp_pause(struct strparser *strp)
|
||||
void strp_unpause(struct strparser *strp)
|
||||
|
||||
Unpause a paused stream parser.
|
||||
|
||||
|
|
|
@ -226,7 +226,7 @@ $ rm configs/<config name>.<number>/<function>
|
|||
where <config name>.<number> specify the configuration and <function> is
|
||||
a symlink to a function being removed from the configuration, e.g.:
|
||||
|
||||
$ rm configfs/c.1/ncm.usb0
|
||||
$ rm configs/c.1/ncm.usb0
|
||||
|
||||
...
|
||||
...
|
||||
|
|
47
MAINTAINERS
47
MAINTAINERS
|
@ -581,7 +581,7 @@ W: https://www.infradead.org/~dhowells/kafs/
|
|||
|
||||
AGPGART DRIVER
|
||||
M: David Airlie <airlied@linux.ie>
|
||||
T: git git://people.freedesktop.org/~airlied/linux (part of drm maint)
|
||||
T: git git://anongit.freedesktop.org/drm/drm
|
||||
S: Maintained
|
||||
F: drivers/char/agp/
|
||||
F: include/linux/agp*
|
||||
|
@ -2523,7 +2523,7 @@ S: Supported
|
|||
F: drivers/scsi/esas2r
|
||||
|
||||
ATUSB IEEE 802.15.4 RADIO DRIVER
|
||||
M: Stefan Schmidt <stefan@osg.samsung.com>
|
||||
M: Stefan Schmidt <stefan@datenfreihafen.org>
|
||||
L: linux-wpan@vger.kernel.org
|
||||
S: Maintained
|
||||
F: drivers/net/ieee802154/atusb.c
|
||||
|
@ -2971,9 +2971,13 @@ N: bcm585*
|
|||
N: bcm586*
|
||||
N: bcm88312
|
||||
N: hr2
|
||||
F: arch/arm64/boot/dts/broadcom/ns2*
|
||||
N: stingray
|
||||
F: arch/arm64/boot/dts/broadcom/northstar2/*
|
||||
F: arch/arm64/boot/dts/broadcom/stingray/*
|
||||
F: drivers/clk/bcm/clk-ns*
|
||||
F: drivers/clk/bcm/clk-sr*
|
||||
F: drivers/pinctrl/bcm/pinctrl-ns*
|
||||
F: include/dt-bindings/clock/bcm-sr*
|
||||
|
||||
BROADCOM KONA GPIO DRIVER
|
||||
M: Ray Jui <rjui@broadcom.com>
|
||||
|
@ -4456,6 +4460,7 @@ F: Documentation/blockdev/drbd/
|
|||
|
||||
DRIVER CORE, KOBJECTS, DEBUGFS AND SYSFS
|
||||
M: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||||
R: "Rafael J. Wysocki" <rafael@kernel.org>
|
||||
T: git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core.git
|
||||
S: Supported
|
||||
F: Documentation/kobject.txt
|
||||
|
@ -4626,7 +4631,7 @@ F: include/uapi/drm/vmwgfx_drm.h
|
|||
DRM DRIVERS
|
||||
M: David Airlie <airlied@linux.ie>
|
||||
L: dri-devel@lists.freedesktop.org
|
||||
T: git git://people.freedesktop.org/~airlied/linux
|
||||
T: git git://anongit.freedesktop.org/drm/drm
|
||||
B: https://bugs.freedesktop.org/
|
||||
C: irc://chat.freenode.net/dri-devel
|
||||
S: Maintained
|
||||
|
@ -5669,7 +5674,7 @@ F: drivers/crypto/caam/
|
|||
F: Documentation/devicetree/bindings/crypto/fsl-sec4.txt
|
||||
|
||||
FREESCALE DIU FRAMEBUFFER DRIVER
|
||||
M: Timur Tabi <timur@tabi.org>
|
||||
M: Timur Tabi <timur@kernel.org>
|
||||
L: linux-fbdev@vger.kernel.org
|
||||
S: Maintained
|
||||
F: drivers/video/fbdev/fsl-diu-fb.*
|
||||
|
@ -5769,7 +5774,7 @@ S: Maintained
|
|||
F: drivers/net/wan/fsl_ucc_hdlc*
|
||||
|
||||
FREESCALE QUICC ENGINE UCC UART DRIVER
|
||||
M: Timur Tabi <timur@tabi.org>
|
||||
M: Timur Tabi <timur@kernel.org>
|
||||
L: linuxppc-dev@lists.ozlabs.org
|
||||
S: Maintained
|
||||
F: drivers/tty/serial/ucc_uart.c
|
||||
|
@ -5785,7 +5790,6 @@ F: include/linux/fsl/
|
|||
|
||||
FREESCALE SOC FS_ENET DRIVER
|
||||
M: Pantelis Antoniou <pantelis.antoniou@gmail.com>
|
||||
M: Vitaly Bordug <vbordug@ru.mvista.com>
|
||||
L: linuxppc-dev@lists.ozlabs.org
|
||||
L: netdev@vger.kernel.org
|
||||
S: Maintained
|
||||
|
@ -5793,7 +5797,7 @@ F: drivers/net/ethernet/freescale/fs_enet/
|
|||
F: include/linux/fs_enet_pd.h
|
||||
|
||||
FREESCALE SOC SOUND DRIVERS
|
||||
M: Timur Tabi <timur@tabi.org>
|
||||
M: Timur Tabi <timur@kernel.org>
|
||||
M: Nicolin Chen <nicoleotsuka@gmail.com>
|
||||
M: Xiubo Li <Xiubo.Lee@gmail.com>
|
||||
R: Fabio Estevam <fabio.estevam@nxp.com>
|
||||
|
@ -6904,7 +6908,7 @@ F: drivers/clk/clk-versaclock5.c
|
|||
|
||||
IEEE 802.15.4 SUBSYSTEM
|
||||
M: Alexander Aring <alex.aring@gmail.com>
|
||||
M: Stefan Schmidt <stefan@osg.samsung.com>
|
||||
M: Stefan Schmidt <stefan@datenfreihafen.org>
|
||||
L: linux-wpan@vger.kernel.org
|
||||
W: http://wpan.cakelab.org/
|
||||
T: git git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan.git
|
||||
|
@ -7091,6 +7095,7 @@ F: include/uapi/linux/input.h
|
|||
F: include/uapi/linux/input-event-codes.h
|
||||
F: include/linux/input/
|
||||
F: Documentation/devicetree/bindings/input/
|
||||
F: Documentation/devicetree/bindings/serio/
|
||||
F: Documentation/input/
|
||||
|
||||
INPUT MULTITOUCH (MT) PROTOCOL
|
||||
|
@ -8624,7 +8629,7 @@ MARVELL MWIFIEX WIRELESS DRIVER
|
|||
M: Amitkumar Karwar <amitkarwar@gmail.com>
|
||||
M: Nishant Sarmukadam <nishants@marvell.com>
|
||||
M: Ganapathi Bhat <gbhat@marvell.com>
|
||||
M: Xinming Hu <huxm@marvell.com>
|
||||
M: Xinming Hu <huxinming820@gmail.com>
|
||||
L: linux-wireless@vger.kernel.org
|
||||
S: Maintained
|
||||
F: drivers/net/wireless/marvell/mwifiex/
|
||||
|
@ -9070,7 +9075,7 @@ S: Maintained
|
|||
F: drivers/usb/mtu3/
|
||||
|
||||
MEGACHIPS STDPXXXX-GE-B850V3-FW LVDS/DP++ BRIDGES
|
||||
M: Peter Senna Tschudin <peter.senna@collabora.com>
|
||||
M: Peter Senna Tschudin <peter.senna@gmail.com>
|
||||
M: Martin Donnelly <martin.donnelly@ge.com>
|
||||
M: Martyn Welch <martyn.welch@collabora.co.uk>
|
||||
S: Maintained
|
||||
|
@ -9882,6 +9887,7 @@ M: Andrew Lunn <andrew@lunn.ch>
|
|||
M: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
|
||||
M: Florian Fainelli <f.fainelli@gmail.com>
|
||||
S: Maintained
|
||||
F: Documentation/devicetree/bindings/net/dsa/
|
||||
F: net/dsa/
|
||||
F: include/net/dsa.h
|
||||
F: include/linux/dsa/
|
||||
|
@ -10208,11 +10214,13 @@ F: sound/soc/codecs/sgtl5000*
|
|||
|
||||
NXP TDA998X DRM DRIVER
|
||||
M: Russell King <linux@armlinux.org.uk>
|
||||
S: Supported
|
||||
S: Maintained
|
||||
T: git git://git.armlinux.org.uk/~rmk/linux-arm.git drm-tda998x-devel
|
||||
T: git git://git.armlinux.org.uk/~rmk/linux-arm.git drm-tda998x-fixes
|
||||
F: drivers/gpu/drm/i2c/tda998x_drv.c
|
||||
F: include/drm/i2c/tda998x.h
|
||||
F: include/dt-bindings/display/tda998x.h
|
||||
K: "nxp,tda998x"
|
||||
|
||||
NXP TFA9879 DRIVER
|
||||
M: Peter Rosin <peda@axentia.se>
|
||||
|
@ -11476,6 +11484,15 @@ W: http://wireless.kernel.org/en/users/Drivers/p54
|
|||
S: Obsolete
|
||||
F: drivers/net/wireless/intersil/prism54/
|
||||
|
||||
PROC FILESYSTEM
|
||||
R: Alexey Dobriyan <adobriyan@gmail.com>
|
||||
L: linux-kernel@vger.kernel.org
|
||||
L: linux-fsdevel@vger.kernel.org
|
||||
S: Maintained
|
||||
F: fs/proc/
|
||||
F: include/linux/proc_fs.h
|
||||
F: tools/testing/selftests/proc/
|
||||
|
||||
PROC SYSCTL
|
||||
M: "Luis R. Rodriguez" <mcgrof@kernel.org>
|
||||
M: Kees Cook <keescook@chromium.org>
|
||||
|
@ -11808,9 +11825,9 @@ F: Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
|
|||
F: drivers/cpufreq/qcom-cpufreq-kryo.c
|
||||
|
||||
QUALCOMM EMAC GIGABIT ETHERNET DRIVER
|
||||
M: Timur Tabi <timur@codeaurora.org>
|
||||
M: Timur Tabi <timur@kernel.org>
|
||||
L: netdev@vger.kernel.org
|
||||
S: Supported
|
||||
S: Maintained
|
||||
F: drivers/net/ethernet/qualcomm/emac/
|
||||
|
||||
QUALCOMM HEXAGON ARCHITECTURE
|
||||
|
@ -11821,7 +11838,7 @@ S: Supported
|
|||
F: arch/hexagon/
|
||||
|
||||
QUALCOMM HIDMA DRIVER
|
||||
M: Sinan Kaya <okaya@codeaurora.org>
|
||||
M: Sinan Kaya <okaya@kernel.org>
|
||||
L: linux-arm-kernel@lists.infradead.org
|
||||
L: linux-arm-msm@vger.kernel.org
|
||||
L: dmaengine@vger.kernel.org
|
||||
|
|
15
Makefile
15
Makefile
|
@ -2,7 +2,7 @@
|
|||
VERSION = 4
|
||||
PATCHLEVEL = 18
|
||||
SUBLEVEL = 0
|
||||
EXTRAVERSION = -rc2
|
||||
EXTRAVERSION = -rc7
|
||||
NAME = Merciless Moray
|
||||
|
||||
# *DOCUMENTATION*
|
||||
|
@ -353,9 +353,9 @@ CONFIG_SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \
|
|||
else if [ -x /bin/bash ]; then echo /bin/bash; \
|
||||
else echo sh; fi ; fi)
|
||||
|
||||
HOST_LFS_CFLAGS := $(shell getconf LFS_CFLAGS)
|
||||
HOST_LFS_LDFLAGS := $(shell getconf LFS_LDFLAGS)
|
||||
HOST_LFS_LIBS := $(shell getconf LFS_LIBS)
|
||||
HOST_LFS_CFLAGS := $(shell getconf LFS_CFLAGS 2>/dev/null)
|
||||
HOST_LFS_LDFLAGS := $(shell getconf LFS_LDFLAGS 2>/dev/null)
|
||||
HOST_LFS_LIBS := $(shell getconf LFS_LIBS 2>/dev/null)
|
||||
|
||||
HOSTCC = gcc
|
||||
HOSTCXX = g++
|
||||
|
@ -507,11 +507,6 @@ ifeq ($(shell $(CONFIG_SHELL) $(srctree)/scripts/gcc-goto.sh $(CC) $(KBUILD_CFLA
|
|||
KBUILD_AFLAGS += -DCC_HAVE_ASM_GOTO
|
||||
endif
|
||||
|
||||
ifeq ($(shell $(CONFIG_SHELL) $(srctree)/scripts/cc-can-link.sh $(CC)), y)
|
||||
CC_CAN_LINK := y
|
||||
export CC_CAN_LINK
|
||||
endif
|
||||
|
||||
# The expansion should be delayed until arch/$(SRCARCH)/Makefile is included.
|
||||
# Some architectures define CROSS_COMPILE in arch/$(SRCARCH)/Makefile.
|
||||
# CC_VERSION_TEXT is referenced from Kconfig (so it needs export),
|
||||
|
@ -1717,6 +1712,6 @@ endif # skip-makefile
|
|||
PHONY += FORCE
|
||||
FORCE:
|
||||
|
||||
# Declare the contents of the .PHONY variable as phony. We keep that
|
||||
# Declare the contents of the PHONY variable as phony. We keep that
|
||||
# information in a variable so we can use it in if_changed and friends.
|
||||
.PHONY: $(PHONY)
|
||||
|
|
|
@ -1180,13 +1180,10 @@ SYSCALL_DEFINE2(osf_getrusage, int, who, struct rusage32 __user *, ru)
|
|||
SYSCALL_DEFINE4(osf_wait4, pid_t, pid, int __user *, ustatus, int, options,
|
||||
struct rusage32 __user *, ur)
|
||||
{
|
||||
unsigned int status = 0;
|
||||
struct rusage r;
|
||||
long err = kernel_wait4(pid, &status, options, &r);
|
||||
long err = kernel_wait4(pid, ustatus, options, &r);
|
||||
if (err <= 0)
|
||||
return err;
|
||||
if (put_user(status, ustatus))
|
||||
return -EFAULT;
|
||||
if (!ur)
|
||||
return err;
|
||||
if (put_tv_to_tv32(&ur->ru_utime, &r.ru_utime))
|
||||
|
|
|
@ -413,7 +413,7 @@ config ARC_HAS_DIV_REM
|
|||
|
||||
config ARC_HAS_ACCL_REGS
|
||||
bool "Reg Pair ACCL:ACCH (FPU and/or MPY > 6)"
|
||||
default n
|
||||
default y
|
||||
help
|
||||
Depending on the configuration, CPU can contain accumulator reg-pair
|
||||
(also referred to as r58:r59). These can also be used by gcc as GPR so
|
||||
|
|
|
@ -16,7 +16,7 @@ endif
|
|||
|
||||
KBUILD_DEFCONFIG := nsim_700_defconfig
|
||||
|
||||
cflags-y += -fno-common -pipe -fno-builtin -D__linux__
|
||||
cflags-y += -fno-common -pipe -fno-builtin -mmedium-calls -D__linux__
|
||||
cflags-$(CONFIG_ISA_ARCOMPACT) += -mA7
|
||||
cflags-$(CONFIG_ISA_ARCV2) += -mcpu=archs
|
||||
|
||||
|
@ -140,16 +140,3 @@ dtbs: scripts
|
|||
|
||||
archclean:
|
||||
$(Q)$(MAKE) $(clean)=$(boot)
|
||||
|
||||
# Hacks to enable final link due to absence of link-time branch relexation
|
||||
# and gcc choosing optimal(shorter) branches at -O3
|
||||
#
|
||||
# vineetg Feb 2010: -mlong-calls switched off for overall kernel build
|
||||
# However lib/decompress_inflate.o (.init.text) calls
|
||||
# zlib_inflate_workspacesize (.text) causing relocation errors.
|
||||
# Thus forcing all exten calls in this file to be long calls
|
||||
export CFLAGS_decompress_inflate.o = -mmedium-calls
|
||||
export CFLAGS_initramfs.o = -mmedium-calls
|
||||
ifdef CONFIG_SMP
|
||||
export CFLAGS_core.o = -mmedium-calls
|
||||
endif
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs/"
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_VM_EVENT_COUNTERS is not set
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_VM_EVENT_COUNTERS is not set
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_VM_EVENT_COUNTERS is not set
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_EXPERT=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_COMPAT_BRK is not set
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_VM_EVENT_COUNTERS is not set
|
||||
|
|
|
@ -9,7 +9,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_VM_EVENT_COUNTERS is not set
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs/"
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
|
|
|
@ -9,7 +9,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs_hs/"
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs/"
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
|
|
|
@ -11,7 +11,6 @@ CONFIG_NAMESPACES=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs_hs/"
|
||||
CONFIG_KALLSYMS_ALL=y
|
||||
CONFIG_EMBEDDED=y
|
||||
CONFIG_PERF_EVENTS=y
|
||||
|
|
|
@ -9,7 +9,6 @@ CONFIG_IKCONFIG_PROC=y
|
|||
# CONFIG_UTS_NS is not set
|
||||
# CONFIG_PID_NS is not set
|
||||
CONFIG_BLK_DEV_INITRD=y
|
||||
CONFIG_INITRAMFS_SOURCE="../arc_initramfs_hs/"
|
||||
CONFIG_PERF_EVENTS=y
|
||||
# CONFIG_COMPAT_BRK is not set
|
||||
CONFIG_KPROBES=y
|
||||
|
|
|
@ -56,7 +56,6 @@ CONFIG_STMMAC_ETH=y
|
|||
# CONFIG_INPUT is not set
|
||||
# CONFIG_SERIO is not set
|
||||
# CONFIG_VT is not set
|
||||
CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
|
||||
# CONFIG_LEGACY_PTYS is not set
|
||||
# CONFIG_DEVKMEM is not set
|
||||
CONFIG_SERIAL_8250=y
|
||||
|
|
|
@ -234,6 +234,9 @@
|
|||
POP gp
|
||||
RESTORE_R12_TO_R0
|
||||
|
||||
#ifdef CONFIG_ARC_CURR_IN_REG
|
||||
ld r25, [sp, 12]
|
||||
#endif
|
||||
ld sp, [sp] /* restore original sp */
|
||||
/* orig_r0, ECR, user_r25 skipped automatically */
|
||||
.endm
|
||||
|
@ -315,6 +318,9 @@
|
|||
POP gp
|
||||
RESTORE_R12_TO_R0
|
||||
|
||||
#ifdef CONFIG_ARC_CURR_IN_REG
|
||||
ld r25, [sp, 12]
|
||||
#endif
|
||||
ld sp, [sp] /* restore original sp */
|
||||
/* orig_r0, ECR, user_r25 skipped automatically */
|
||||
.endm
|
||||
|
|
|
@ -86,9 +86,6 @@
|
|||
POP r1
|
||||
POP r0
|
||||
|
||||
#ifdef CONFIG_ARC_CURR_IN_REG
|
||||
ld r25, [sp, 12]
|
||||
#endif
|
||||
.endm
|
||||
|
||||
/*--------------------------------------------------------------
|
||||
|
|
|
@ -34,9 +34,7 @@ struct machine_desc {
|
|||
const char *name;
|
||||
const char **dt_compat;
|
||||
void (*init_early)(void);
|
||||
#ifdef CONFIG_SMP
|
||||
void (*init_per_cpu)(unsigned int);
|
||||
#endif
|
||||
void (*init_machine)(void);
|
||||
void (*init_late)(void);
|
||||
|
||||
|
|
|
@ -105,7 +105,7 @@ typedef pte_t * pgtable_t;
|
|||
#define virt_addr_valid(kaddr) pfn_valid(virt_to_pfn(kaddr))
|
||||
|
||||
/* Default Permissions for stack/heaps pages (Non Executable) */
|
||||
#define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_MAYREAD | VM_MAYWRITE)
|
||||
#define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
|
||||
|
||||
#define WANT_PAGE_VIRTUAL 1
|
||||
|
||||
|
|
|
@ -377,7 +377,7 @@ void update_mmu_cache(struct vm_area_struct *vma, unsigned long address,
|
|||
|
||||
/* Decode a PTE containing swap "identifier "into constituents */
|
||||
#define __swp_type(pte_lookalike) (((pte_lookalike).val) & 0x1f)
|
||||
#define __swp_offset(pte_lookalike) ((pte_lookalike).val << 13)
|
||||
#define __swp_offset(pte_lookalike) ((pte_lookalike).val >> 13)
|
||||
|
||||
/* NOPs, to keep generic kernel happy */
|
||||
#define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) })
|
||||
|
|
|
@ -31,10 +31,10 @@ void __init init_IRQ(void)
|
|||
/* a SMP H/w block could do IPI IRQ request here */
|
||||
if (plat_smp_ops.init_per_cpu)
|
||||
plat_smp_ops.init_per_cpu(smp_processor_id());
|
||||
#endif
|
||||
|
||||
if (machine_desc->init_per_cpu)
|
||||
machine_desc->init_per_cpu(smp_processor_id());
|
||||
#endif
|
||||
}
|
||||
|
||||
/*
|
||||
|
|
|
@ -47,7 +47,8 @@ SYSCALL_DEFINE0(arc_gettls)
|
|||
SYSCALL_DEFINE3(arc_usr_cmpxchg, int *, uaddr, int, expected, int, new)
|
||||
{
|
||||
struct pt_regs *regs = current_pt_regs();
|
||||
int uval = -EFAULT;
|
||||
u32 uval;
|
||||
int ret;
|
||||
|
||||
/*
|
||||
* This is only for old cores lacking LLOCK/SCOND, which by defintion
|
||||
|
@ -60,23 +61,47 @@ SYSCALL_DEFINE3(arc_usr_cmpxchg, int *, uaddr, int, expected, int, new)
|
|||
/* Z indicates to userspace if operation succeded */
|
||||
regs->status32 &= ~STATUS_Z_MASK;
|
||||
|
||||
if (!access_ok(VERIFY_WRITE, uaddr, sizeof(int)))
|
||||
return -EFAULT;
|
||||
ret = access_ok(VERIFY_WRITE, uaddr, sizeof(*uaddr));
|
||||
if (!ret)
|
||||
goto fail;
|
||||
|
||||
again:
|
||||
preempt_disable();
|
||||
|
||||
if (__get_user(uval, uaddr))
|
||||
goto done;
|
||||
ret = __get_user(uval, uaddr);
|
||||
if (ret)
|
||||
goto fault;
|
||||
|
||||
if (uval == expected) {
|
||||
if (!__put_user(new, uaddr))
|
||||
regs->status32 |= STATUS_Z_MASK;
|
||||
}
|
||||
if (uval != expected)
|
||||
goto out;
|
||||
|
||||
done:
|
||||
ret = __put_user(new, uaddr);
|
||||
if (ret)
|
||||
goto fault;
|
||||
|
||||
regs->status32 |= STATUS_Z_MASK;
|
||||
|
||||
out:
|
||||
preempt_enable();
|
||||
return uval;
|
||||
|
||||
fault:
|
||||
preempt_enable();
|
||||
|
||||
return uval;
|
||||
if (unlikely(ret != -EFAULT))
|
||||
goto fail;
|
||||
|
||||
down_read(¤t->mm->mmap_sem);
|
||||
ret = fixup_user_fault(current, current->mm, (unsigned long) uaddr,
|
||||
FAULT_FLAG_WRITE, NULL);
|
||||
up_read(¤t->mm->mmap_sem);
|
||||
|
||||
if (likely(!ret))
|
||||
goto again;
|
||||
|
||||
fail:
|
||||
force_sig(SIGSEGV, current);
|
||||
return ret;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_ISA_ARCV2
|
||||
|
|
|
@ -7,5 +7,8 @@
|
|||
|
||||
menuconfig ARC_SOC_HSDK
|
||||
bool "ARC HS Development Kit SOC"
|
||||
depends on ISA_ARCV2
|
||||
select ARC_HAS_ACCL_REGS
|
||||
select CLK_HSDK
|
||||
select RESET_HSDK
|
||||
select MIGHT_HAVE_PCI
|
||||
|
|
|
@ -42,6 +42,66 @@ static void __init hsdk_init_per_cpu(unsigned int cpu)
|
|||
#define SDIO_UHS_REG_EXT (SDIO_BASE + 0x108)
|
||||
#define SDIO_UHS_REG_EXT_DIV_2 (2 << 30)
|
||||
|
||||
#define HSDK_GPIO_INTC (ARC_PERIPHERAL_BASE + 0x3000)
|
||||
|
||||
static void __init hsdk_enable_gpio_intc_wire(void)
|
||||
{
|
||||
/*
|
||||
* Peripherals on CPU Card are wired to cpu intc via intermediate
|
||||
* DW APB GPIO blocks (mainly for debouncing)
|
||||
*
|
||||
* ---------------------
|
||||
* | snps,archs-intc |
|
||||
* ---------------------
|
||||
* |
|
||||
* ----------------------
|
||||
* | snps,archs-idu-intc |
|
||||
* ----------------------
|
||||
* | | | | |
|
||||
* | [eth] [USB] [... other peripherals]
|
||||
* |
|
||||
* -------------------
|
||||
* | snps,dw-apb-intc |
|
||||
* -------------------
|
||||
* | | | |
|
||||
* [Bt] [HAPS] [... other peripherals]
|
||||
*
|
||||
* Current implementation of "irq-dw-apb-ictl" driver doesn't work well
|
||||
* with stacked INTCs. In particular problem happens if its master INTC
|
||||
* not yet instantiated. See discussion here -
|
||||
* https://lkml.org/lkml/2015/3/4/755
|
||||
*
|
||||
* So setup the first gpio block as a passive pass thru and hide it from
|
||||
* DT hardware topology - connect intc directly to cpu intc
|
||||
* The GPIO "wire" needs to be init nevertheless (here)
|
||||
*
|
||||
* One side adv is that peripheral interrupt handling avoids one nested
|
||||
* intc ISR hop
|
||||
*
|
||||
* According to HSDK User's Manual [1], "Table 2 Interrupt Mapping"
|
||||
* we have the following GPIO input lines used as sources of interrupt:
|
||||
* - GPIO[0] - Bluetooth interrupt of RS9113 module
|
||||
* - GPIO[2] - HAPS interrupt (on HapsTrak 3 connector)
|
||||
* - GPIO[3] - Audio codec (MAX9880A) interrupt
|
||||
* - GPIO[8-23] - Available on Arduino and PMOD_x headers
|
||||
* For now there's no use of Arduino and PMOD_x headers in Linux
|
||||
* use-case so we only enable lines 0, 2 and 3.
|
||||
*
|
||||
* [1] https://github.com/foss-for-synopsys-dwc-arc-processors/ARC-Development-Systems-Forum/wiki/docs/ARC_HSDK_User_Guide.pdf
|
||||
*/
|
||||
#define GPIO_INTEN (HSDK_GPIO_INTC + 0x30)
|
||||
#define GPIO_INTMASK (HSDK_GPIO_INTC + 0x34)
|
||||
#define GPIO_INTTYPE_LEVEL (HSDK_GPIO_INTC + 0x38)
|
||||
#define GPIO_INT_POLARITY (HSDK_GPIO_INTC + 0x3c)
|
||||
#define GPIO_INT_CONNECTED_MASK 0x0d
|
||||
|
||||
iowrite32(0xffffffff, (void __iomem *) GPIO_INTMASK);
|
||||
iowrite32(~GPIO_INT_CONNECTED_MASK, (void __iomem *) GPIO_INTMASK);
|
||||
iowrite32(0x00000000, (void __iomem *) GPIO_INTTYPE_LEVEL);
|
||||
iowrite32(0xffffffff, (void __iomem *) GPIO_INT_POLARITY);
|
||||
iowrite32(GPIO_INT_CONNECTED_MASK, (void __iomem *) GPIO_INTEN);
|
||||
}
|
||||
|
||||
static void __init hsdk_init_early(void)
|
||||
{
|
||||
/*
|
||||
|
@ -62,6 +122,8 @@ static void __init hsdk_init_early(void)
|
|||
* minimum possible div-by-2.
|
||||
*/
|
||||
iowrite32(SDIO_UHS_REG_EXT_DIV_2, (void __iomem *) SDIO_UHS_REG_EXT);
|
||||
|
||||
hsdk_enable_gpio_intc_wire();
|
||||
}
|
||||
|
||||
static const char *hsdk_compat[] __initconst = {
|
||||
|
|
|
@ -1245,8 +1245,14 @@ config PCI
|
|||
VESA. If you have PCI, say Y, otherwise N.
|
||||
|
||||
config PCI_DOMAINS
|
||||
bool
|
||||
bool "Support for multiple PCI domains"
|
||||
depends on PCI
|
||||
help
|
||||
Enable PCI domains kernel management. Say Y if your machine
|
||||
has a PCI bus hierarchy that requires more than one PCI
|
||||
domain (aka segment) to be correctly managed. Say N otherwise.
|
||||
|
||||
If you don't know what to do here, say N.
|
||||
|
||||
config PCI_DOMAINS_GENERIC
|
||||
def_bool PCI_DOMAINS
|
||||
|
|
|
@ -168,7 +168,6 @@
|
|||
AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
|
||||
AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
|
||||
AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
|
||||
AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* mcasp0_aclkr.mmc0_sdwp */
|
||||
>;
|
||||
};
|
||||
|
||||
|
|
|
@ -39,6 +39,8 @@
|
|||
ti,davinci-ctrl-ram-size = <0x2000>;
|
||||
ti,davinci-rmii-en = /bits/ 8 <1>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
clocks = <&emac_ick>;
|
||||
clock-names = "ick";
|
||||
};
|
||||
|
||||
davinci_mdio: ethernet@5c030000 {
|
||||
|
@ -49,6 +51,8 @@
|
|||
bus_freq = <1000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
clocks = <&emac_fck>;
|
||||
clock-names = "fck";
|
||||
};
|
||||
|
||||
uart4: serial@4809e000 {
|
||||
|
@ -87,6 +91,11 @@
|
|||
};
|
||||
};
|
||||
|
||||
/* Table Table 5-79 of the TRM shows 480ab000 is reserved */
|
||||
&usb_otg_hs {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&iva {
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
|
@ -610,6 +610,8 @@
|
|||
|
||||
touchscreen-size-x = <480>;
|
||||
touchscreen-size-y = <272>;
|
||||
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
tlv320aic3106: tlv320aic3106@1b {
|
||||
|
|
|
@ -139,7 +139,7 @@
|
|||
3700 5
|
||||
3900 6
|
||||
4000 7>;
|
||||
cooling-cells = <2>;
|
||||
#cooling-cells = <2>;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
|
|
|
@ -547,7 +547,7 @@
|
|||
|
||||
thermal: thermal@e8078 {
|
||||
compatible = "marvell,armada380-thermal";
|
||||
reg = <0xe4078 0x4>, <0xe4074 0x4>;
|
||||
reg = <0xe4078 0x4>, <0xe4070 0x8>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
|
|
@ -216,7 +216,7 @@
|
|||
reg = <0x18008000 0x100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-frequency = <100000>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
@ -245,7 +245,7 @@
|
|||
reg = <0x1800b000 0x100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-frequency = <100000>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
@ -256,7 +256,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <0>;
|
||||
|
||||
|
@ -278,10 +278,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 97 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 98 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 99 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -291,7 +291,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <1>;
|
||||
|
||||
|
@ -313,10 +313,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 103 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 104 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 105 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
|
|
|
@ -264,7 +264,7 @@
|
|||
reg = <0x38000 0x50>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 95 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-frequency = <100000>;
|
||||
};
|
||||
|
||||
|
@ -279,7 +279,7 @@
|
|||
reg = <0x3b000 0x50>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-frequency = <100000>;
|
||||
};
|
||||
};
|
||||
|
@ -300,7 +300,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <0>;
|
||||
|
||||
|
@ -322,10 +322,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 182 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 183 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 184 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 185 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
|
||||
brcm,pcie-msi-inten;
|
||||
};
|
||||
};
|
||||
|
@ -336,7 +336,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <1>;
|
||||
|
||||
|
@ -358,10 +358,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 189 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 190 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 191 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
|
||||
brcm,pcie-msi-inten;
|
||||
};
|
||||
};
|
||||
|
|
|
@ -391,7 +391,7 @@
|
|||
reg = <0x38000 0x50>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clock-frequency = <100000>;
|
||||
dma-coherent;
|
||||
status = "disabled";
|
||||
|
@ -496,7 +496,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <0>;
|
||||
|
||||
|
@ -519,10 +519,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 128 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 129 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 130 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
|
||||
brcm,pcie-msi-inten;
|
||||
};
|
||||
};
|
||||
|
@ -533,7 +533,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <1>;
|
||||
|
||||
|
@ -556,10 +556,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 134 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 135 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 136 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
|
||||
brcm,pcie-msi-inten;
|
||||
};
|
||||
};
|
||||
|
@ -570,7 +570,7 @@
|
|||
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
|
||||
interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
linux,pci-domain = <2>;
|
||||
|
||||
|
@ -593,10 +593,10 @@
|
|||
compatible = "brcm,iproc-msi";
|
||||
msi-controller;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 140 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 141 IRQ_TYPE_NONE>,
|
||||
<GIC_SPI 142 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
|
||||
brcm,pcie-msi-inten;
|
||||
};
|
||||
};
|
||||
|
|
|
@ -365,7 +365,7 @@
|
|||
i2c0: i2c@18009000 {
|
||||
compatible = "brcm,iproc-i2c";
|
||||
reg = <0x18009000 0x50>;
|
||||
interrupts = <GIC_SPI 121 IRQ_TYPE_NONE>;
|
||||
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
clock-frequency = <100000>;
|
||||
|
|
|
@ -549,11 +549,7 @@
|
|||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
reg = <0x226000 0x1000>;
|
||||
interrupts = <42 IRQ_TYPE_EDGE_BOTH
|
||||
43 IRQ_TYPE_EDGE_BOTH 44 IRQ_TYPE_EDGE_BOTH
|
||||
45 IRQ_TYPE_EDGE_BOTH 46 IRQ_TYPE_EDGE_BOTH
|
||||
47 IRQ_TYPE_EDGE_BOTH 48 IRQ_TYPE_EDGE_BOTH
|
||||
49 IRQ_TYPE_EDGE_BOTH 50 IRQ_TYPE_EDGE_BOTH>;
|
||||
interrupts = <42 43 44 45 46 47 48 49 50>;
|
||||
ti,ngpio = <144>;
|
||||
ti,davinci-gpio-unbanked = <0>;
|
||||
status = "disabled";
|
||||
|
|
|
@ -1580,7 +1580,6 @@
|
|||
dr_mode = "otg";
|
||||
snps,dis_u3_susphy_quirk;
|
||||
snps,dis_u2_susphy_quirk;
|
||||
snps,dis_metastability_quirk;
|
||||
};
|
||||
};
|
||||
|
||||
|
@ -1608,6 +1607,7 @@
|
|||
dr_mode = "otg";
|
||||
snps,dis_u3_susphy_quirk;
|
||||
snps,dis_u2_susphy_quirk;
|
||||
snps,dis_metastability_quirk;
|
||||
};
|
||||
};
|
||||
|
||||
|
|
|
@ -770,7 +770,7 @@
|
|||
|
||||
pinctrl_ts: tsgrp {
|
||||
fsl,pins = <
|
||||
MX51_PAD_CSI1_D8__GPIO3_12 0x85
|
||||
MX51_PAD_CSI1_D8__GPIO3_12 0x04
|
||||
MX51_PAD_CSI1_D9__GPIO3_13 0x85
|
||||
>;
|
||||
};
|
||||
|
|
|
@ -90,7 +90,7 @@
|
|||
clocks = <&clks IMX6Q_CLK_ECSPI5>,
|
||||
<&clks IMX6Q_CLK_ECSPI5>;
|
||||
clock-names = "ipg", "per";
|
||||
dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
|
||||
dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
|
||||
dma-names = "rx", "tx";
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
|
@ -692,7 +692,7 @@
|
|||
dsa,member = <0 0>;
|
||||
eeprom-length = <512>;
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
|
||||
|
|
|
@ -1344,7 +1344,7 @@
|
|||
ranges = <0x81000000 0 0 0x08f80000 0 0x00010000 /* downstream I/O */
|
||||
0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
|
||||
num-lanes = <1>;
|
||||
interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "msi";
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-map-mask = <0 0 0 0x7>;
|
||||
|
|
|
@ -159,13 +159,7 @@
|
|||
|
||||
dais = <&mcbsp2_port>, <&mcbsp3_port>;
|
||||
};
|
||||
};
|
||||
|
||||
&dss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio6 {
|
||||
pwm8: dmtimer-pwm-8 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vibrator_direction_pin>;
|
||||
|
@ -192,7 +186,10 @@
|
|||
pwm-names = "enable", "direction";
|
||||
direction-duty-cycle-ns = <10000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&dss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dsi1 {
|
||||
|
|
|
@ -748,13 +748,13 @@
|
|||
nand0: nand@ff900000 {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
compatible = "denali,denali-nand-dt";
|
||||
compatible = "altr,socfpga-denali-nand";
|
||||
reg = <0xff900000 0x100000>,
|
||||
<0xffb80000 0x10000>;
|
||||
reg-names = "nand_data", "denali_reg";
|
||||
interrupts = <0x0 0x90 0x4>;
|
||||
dma-mask = <0xffffffff>;
|
||||
clocks = <&nand_clk>;
|
||||
clocks = <&nand_x_clk>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
|
|
|
@ -593,8 +593,7 @@
|
|||
#size-cells = <0>;
|
||||
reg = <0xffda5000 0x100>;
|
||||
interrupts = <0 102 4>;
|
||||
num-chipselect = <4>;
|
||||
bus-num = <0>;
|
||||
num-cs = <4>;
|
||||
/*32bit_access;*/
|
||||
tx-dma-channel = <&pdma 16>;
|
||||
rx-dma-channel = <&pdma 17>;
|
||||
|
@ -633,7 +632,7 @@
|
|||
nand: nand@ffb90000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand";
|
||||
compatible = "altr,socfpga-denali-nand";
|
||||
reg = <0xffb90000 0x72000>,
|
||||
<0xffb80000 0x10000>;
|
||||
reg-names = "nand_data", "denali_reg";
|
||||
|
|
|
@ -10,7 +10,7 @@ obj-$(CONFIG_DMABOUNCE) += dmabounce.o
|
|||
obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
|
||||
obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
|
||||
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
|
||||
obj-$(CONFIG_SMP) += secure_cntvoff.o
|
||||
obj-$(CONFIG_CPU_V7) += secure_cntvoff.o
|
||||
obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o
|
||||
obj-$(CONFIG_MCPM) += mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o
|
||||
CFLAGS_REMOVE_mcpm_entry.o = -pg
|
||||
|
|
|
@ -141,9 +141,11 @@ CONFIG_USB_STORAGE=y
|
|||
CONFIG_USB_CHIPIDEA=y
|
||||
CONFIG_USB_CHIPIDEA_UDC=y
|
||||
CONFIG_USB_CHIPIDEA_HOST=y
|
||||
CONFIG_USB_CHIPIDEA_ULPI=y
|
||||
CONFIG_NOP_USB_XCEIV=y
|
||||
CONFIG_USB_GADGET=y
|
||||
CONFIG_USB_ETH=m
|
||||
CONFIG_USB_ULPI_BUS=y
|
||||
CONFIG_MMC=y
|
||||
CONFIG_MMC_SDHCI=y
|
||||
CONFIG_MMC_SDHCI_PLTFM=y
|
||||
|
|
|
@ -302,6 +302,7 @@ CONFIG_USB_STORAGE=y
|
|||
CONFIG_USB_CHIPIDEA=y
|
||||
CONFIG_USB_CHIPIDEA_UDC=y
|
||||
CONFIG_USB_CHIPIDEA_HOST=y
|
||||
CONFIG_USB_CHIPIDEA_ULPI=y
|
||||
CONFIG_USB_SERIAL=m
|
||||
CONFIG_USB_SERIAL_GENERIC=y
|
||||
CONFIG_USB_SERIAL_FTDI_SIO=m
|
||||
|
@ -338,6 +339,7 @@ CONFIG_USB_GADGETFS=m
|
|||
CONFIG_USB_FUNCTIONFS=m
|
||||
CONFIG_USB_MASS_STORAGE=m
|
||||
CONFIG_USB_G_SERIAL=m
|
||||
CONFIG_USB_ULPI_BUS=y
|
||||
CONFIG_MMC=y
|
||||
CONFIG_MMC_SDHCI=y
|
||||
CONFIG_MMC_SDHCI_PLTFM=y
|
||||
|
|
|
@ -1,5 +1,4 @@
|
|||
CONFIG_SYSVIPC=y
|
||||
CONFIG_FHANDLE=y
|
||||
CONFIG_NO_HZ=y
|
||||
CONFIG_HIGH_RES_TIMERS=y
|
||||
CONFIG_CGROUPS=y
|
||||
|
@ -10,20 +9,10 @@ CONFIG_MODULES=y
|
|||
CONFIG_MODULE_UNLOAD=y
|
||||
CONFIG_PARTITION_ADVANCED=y
|
||||
CONFIG_CMDLINE_PARTITION=y
|
||||
CONFIG_ARCH_MULTI_V7=y
|
||||
# CONFIG_ARCH_MULTI_V5 is not set
|
||||
# CONFIG_ARCH_MULTI_V4 is not set
|
||||
CONFIG_ARCH_VIRT=y
|
||||
CONFIG_ARCH_ALPINE=y
|
||||
CONFIG_ARCH_ARTPEC=y
|
||||
CONFIG_MACH_ARTPEC6=y
|
||||
CONFIG_ARCH_MVEBU=y
|
||||
CONFIG_MACH_ARMADA_370=y
|
||||
CONFIG_MACH_ARMADA_375=y
|
||||
CONFIG_MACH_ARMADA_38X=y
|
||||
CONFIG_MACH_ARMADA_39X=y
|
||||
CONFIG_MACH_ARMADA_XP=y
|
||||
CONFIG_MACH_DOVE=y
|
||||
CONFIG_ARCH_AT91=y
|
||||
CONFIG_SOC_SAMA5D2=y
|
||||
CONFIG_SOC_SAMA5D3=y
|
||||
|
@ -32,9 +21,9 @@ CONFIG_ARCH_BCM=y
|
|||
CONFIG_ARCH_BCM_CYGNUS=y
|
||||
CONFIG_ARCH_BCM_HR2=y
|
||||
CONFIG_ARCH_BCM_NSP=y
|
||||
CONFIG_ARCH_BCM_21664=y
|
||||
CONFIG_ARCH_BCM_281XX=y
|
||||
CONFIG_ARCH_BCM_5301X=y
|
||||
CONFIG_ARCH_BCM_281XX=y
|
||||
CONFIG_ARCH_BCM_21664=y
|
||||
CONFIG_ARCH_BCM2835=y
|
||||
CONFIG_ARCH_BCM_63XX=y
|
||||
CONFIG_ARCH_BRCMSTB=y
|
||||
|
@ -43,14 +32,14 @@ CONFIG_MACH_BERLIN_BG2=y
|
|||
CONFIG_MACH_BERLIN_BG2CD=y
|
||||
CONFIG_MACH_BERLIN_BG2Q=y
|
||||
CONFIG_ARCH_DIGICOLOR=y
|
||||
CONFIG_ARCH_EXYNOS=y
|
||||
CONFIG_EXYNOS5420_MCPM=y
|
||||
CONFIG_ARCH_HIGHBANK=y
|
||||
CONFIG_ARCH_HISI=y
|
||||
CONFIG_ARCH_HI3xxx=y
|
||||
CONFIG_ARCH_HIX5HD2=y
|
||||
CONFIG_ARCH_HIP01=y
|
||||
CONFIG_ARCH_HIP04=y
|
||||
CONFIG_ARCH_KEYSTONE=y
|
||||
CONFIG_ARCH_MESON=y
|
||||
CONFIG_ARCH_HIX5HD2=y
|
||||
CONFIG_ARCH_MXC=y
|
||||
CONFIG_SOC_IMX50=y
|
||||
CONFIG_SOC_IMX51=y
|
||||
|
@ -60,29 +49,30 @@ CONFIG_SOC_IMX6SL=y
|
|||
CONFIG_SOC_IMX6SX=y
|
||||
CONFIG_SOC_IMX6UL=y
|
||||
CONFIG_SOC_IMX7D=y
|
||||
CONFIG_SOC_VF610=y
|
||||
CONFIG_SOC_LS1021A=y
|
||||
CONFIG_SOC_VF610=y
|
||||
CONFIG_ARCH_KEYSTONE=y
|
||||
CONFIG_ARCH_MEDIATEK=y
|
||||
CONFIG_ARCH_MESON=y
|
||||
CONFIG_ARCH_MVEBU=y
|
||||
CONFIG_MACH_ARMADA_370=y
|
||||
CONFIG_MACH_ARMADA_375=y
|
||||
CONFIG_MACH_ARMADA_38X=y
|
||||
CONFIG_MACH_ARMADA_39X=y
|
||||
CONFIG_MACH_ARMADA_XP=y
|
||||
CONFIG_MACH_DOVE=y
|
||||
CONFIG_ARCH_OMAP3=y
|
||||
CONFIG_ARCH_OMAP4=y
|
||||
CONFIG_SOC_OMAP5=y
|
||||
CONFIG_SOC_AM33XX=y
|
||||
CONFIG_SOC_AM43XX=y
|
||||
CONFIG_SOC_DRA7XX=y
|
||||
CONFIG_ARCH_SIRF=y
|
||||
CONFIG_ARCH_QCOM=y
|
||||
CONFIG_ARCH_MEDIATEK=y
|
||||
CONFIG_ARCH_MSM8X60=y
|
||||
CONFIG_ARCH_MSM8960=y
|
||||
CONFIG_ARCH_MSM8974=y
|
||||
CONFIG_ARCH_ROCKCHIP=y
|
||||
CONFIG_ARCH_SOCFPGA=y
|
||||
CONFIG_PLAT_SPEAR=y
|
||||
CONFIG_ARCH_SPEAR13XX=y
|
||||
CONFIG_MACH_SPEAR1310=y
|
||||
CONFIG_MACH_SPEAR1340=y
|
||||
CONFIG_ARCH_STI=y
|
||||
CONFIG_ARCH_STM32=y
|
||||
CONFIG_ARCH_EXYNOS=y
|
||||
CONFIG_EXYNOS5420_MCPM=y
|
||||
CONFIG_ARCH_RENESAS=y
|
||||
CONFIG_ARCH_EMEV2=y
|
||||
CONFIG_ARCH_R7S72100=y
|
||||
|
@ -99,40 +89,33 @@ CONFIG_ARCH_R8A7792=y
|
|||
CONFIG_ARCH_R8A7793=y
|
||||
CONFIG_ARCH_R8A7794=y
|
||||
CONFIG_ARCH_SH73A0=y
|
||||
CONFIG_ARCH_SOCFPGA=y
|
||||
CONFIG_PLAT_SPEAR=y
|
||||
CONFIG_ARCH_SPEAR13XX=y
|
||||
CONFIG_MACH_SPEAR1310=y
|
||||
CONFIG_MACH_SPEAR1340=y
|
||||
CONFIG_ARCH_STI=y
|
||||
CONFIG_ARCH_STM32=y
|
||||
CONFIG_ARCH_SUNXI=y
|
||||
CONFIG_ARCH_SIRF=y
|
||||
CONFIG_ARCH_TEGRA=y
|
||||
CONFIG_ARCH_TEGRA_2x_SOC=y
|
||||
CONFIG_ARCH_TEGRA_3x_SOC=y
|
||||
CONFIG_ARCH_TEGRA_114_SOC=y
|
||||
CONFIG_ARCH_TEGRA_124_SOC=y
|
||||
CONFIG_ARCH_UNIPHIER=y
|
||||
CONFIG_ARCH_U8500=y
|
||||
CONFIG_MACH_HREFV60=y
|
||||
CONFIG_MACH_SNOWBALL=y
|
||||
CONFIG_ARCH_VEXPRESS=y
|
||||
CONFIG_ARCH_VEXPRESS_TC2_PM=y
|
||||
CONFIG_ARCH_WM8850=y
|
||||
CONFIG_ARCH_ZYNQ=y
|
||||
CONFIG_TRUSTED_FOUNDATIONS=y
|
||||
CONFIG_PCI=y
|
||||
CONFIG_PCI_HOST_GENERIC=y
|
||||
CONFIG_PCI_DRA7XX=y
|
||||
CONFIG_PCI_DRA7XX_EP=y
|
||||
CONFIG_PCI_KEYSTONE=y
|
||||
CONFIG_PCI_MSI=y
|
||||
CONFIG_PCIEPORTBUS=y
|
||||
CONFIG_PCI_MVEBU=y
|
||||
CONFIG_PCI_TEGRA=y
|
||||
CONFIG_PCI_RCAR_GEN2=y
|
||||
CONFIG_PCIE_RCAR=y
|
||||
CONFIG_PCIEPORTBUS=y
|
||||
CONFIG_PCI_DRA7XX_EP=y
|
||||
CONFIG_PCI_KEYSTONE=y
|
||||
CONFIG_PCI_ENDPOINT=y
|
||||
CONFIG_PCI_ENDPOINT_CONFIGFS=y
|
||||
CONFIG_PCI_EPF_TEST=m
|
||||
CONFIG_SMP=y
|
||||
CONFIG_NR_CPUS=16
|
||||
CONFIG_HIGHPTE=y
|
||||
CONFIG_CMA=y
|
||||
CONFIG_SECCOMP=y
|
||||
CONFIG_ARM_APPENDED_DTB=y
|
||||
CONFIG_ARM_ATAG_DTB_COMPAT=y
|
||||
|
@ -145,14 +128,14 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
|
|||
CONFIG_CPU_FREQ_GOV_USERSPACE=m
|
||||
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
|
||||
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
|
||||
CONFIG_CPUFREQ_DT=y
|
||||
CONFIG_ARM_IMX6Q_CPUFREQ=y
|
||||
CONFIG_QORIQ_CPUFREQ=y
|
||||
CONFIG_CPU_IDLE=y
|
||||
CONFIG_ARM_CPUIDLE=y
|
||||
CONFIG_NEON=y
|
||||
CONFIG_KERNEL_MODE_NEON=y
|
||||
CONFIG_ARM_ZYNQ_CPUIDLE=y
|
||||
CONFIG_ARM_EXYNOS_CPUIDLE=y
|
||||
CONFIG_KERNEL_MODE_NEON=y
|
||||
CONFIG_NET=y
|
||||
CONFIG_PACKET=y
|
||||
CONFIG_UNIX=y
|
||||
|
@ -170,23 +153,13 @@ CONFIG_IPV6_MIP6=m
|
|||
CONFIG_IPV6_TUNNEL=m
|
||||
CONFIG_IPV6_MULTIPLE_TABLES=y
|
||||
CONFIG_NET_DSA=m
|
||||
CONFIG_NET_SWITCHDEV=y
|
||||
CONFIG_CAN=y
|
||||
CONFIG_CAN_RAW=y
|
||||
CONFIG_CAN_BCM=y
|
||||
CONFIG_CAN_DEV=y
|
||||
CONFIG_CAN_AT91=m
|
||||
CONFIG_CAN_FLEXCAN=m
|
||||
CONFIG_CAN_RCAR=m
|
||||
CONFIG_CAN_XILINXCAN=y
|
||||
CONFIG_CAN_MCP251X=y
|
||||
CONFIG_NET_DSA_BCM_SF2=m
|
||||
CONFIG_B53=m
|
||||
CONFIG_B53_SPI_DRIVER=m
|
||||
CONFIG_B53_MDIO_DRIVER=m
|
||||
CONFIG_B53_MMAP_DRIVER=m
|
||||
CONFIG_B53_SRAB_DRIVER=m
|
||||
CONFIG_CAN_SUN4I=y
|
||||
CONFIG_CAN_XILINXCAN=y
|
||||
CONFIG_CAN_RCAR=m
|
||||
CONFIG_CAN_MCP251X=y
|
||||
CONFIG_BT=m
|
||||
CONFIG_BT_HCIUART=m
|
||||
CONFIG_BT_HCIUART_BCM=y
|
||||
|
@ -199,11 +172,9 @@ CONFIG_RFKILL_INPUT=y
|
|||
CONFIG_RFKILL_GPIO=y
|
||||
CONFIG_DEVTMPFS=y
|
||||
CONFIG_DEVTMPFS_MOUNT=y
|
||||
CONFIG_DMA_CMA=y
|
||||
CONFIG_CMA_SIZE_MBYTES=64
|
||||
CONFIG_OMAP_OCP2SCP=y
|
||||
CONFIG_SIMPLE_PM_BUS=y
|
||||
CONFIG_SUNXI_RSB=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_CMDLINE_PARTS=y
|
||||
CONFIG_MTD_BLOCK=y
|
||||
|
@ -236,7 +207,6 @@ CONFIG_PCI_ENDPOINT_TEST=m
|
|||
CONFIG_EEPROM_AT24=y
|
||||
CONFIG_BLK_DEV_SD=y
|
||||
CONFIG_BLK_DEV_SR=y
|
||||
CONFIG_SCSI_MULTI_LUN=y
|
||||
CONFIG_ATA=y
|
||||
CONFIG_SATA_AHCI=y
|
||||
CONFIG_SATA_AHCI_PLATFORM=y
|
||||
|
@ -251,14 +221,20 @@ CONFIG_SATA_MV=y
|
|||
CONFIG_SATA_RCAR=y
|
||||
CONFIG_NETDEVICES=y
|
||||
CONFIG_VIRTIO_NET=y
|
||||
CONFIG_HIX5HD2_GMAC=y
|
||||
CONFIG_B53_SPI_DRIVER=m
|
||||
CONFIG_B53_MDIO_DRIVER=m
|
||||
CONFIG_B53_MMAP_DRIVER=m
|
||||
CONFIG_B53_SRAB_DRIVER=m
|
||||
CONFIG_NET_DSA_BCM_SF2=m
|
||||
CONFIG_SUN4I_EMAC=y
|
||||
CONFIG_MACB=y
|
||||
CONFIG_BCMGENET=m
|
||||
CONFIG_BGMAC_BCMA=y
|
||||
CONFIG_SYSTEMPORT=m
|
||||
CONFIG_MACB=y
|
||||
CONFIG_NET_CALXEDA_XGMAC=y
|
||||
CONFIG_GIANFAR=y
|
||||
CONFIG_HIX5HD2_GMAC=y
|
||||
CONFIG_E1000E=y
|
||||
CONFIG_IGB=y
|
||||
CONFIG_MV643XX_ETH=y
|
||||
CONFIG_MVNETA=y
|
||||
|
@ -268,19 +244,17 @@ CONFIG_R8169=y
|
|||
CONFIG_SH_ETH=y
|
||||
CONFIG_SMSC911X=y
|
||||
CONFIG_STMMAC_ETH=y
|
||||
CONFIG_STMMAC_PLATFORM=y
|
||||
CONFIG_DWMAC_DWC_QOS_ETH=y
|
||||
CONFIG_TI_CPSW=y
|
||||
CONFIG_XILINX_EMACLITE=y
|
||||
CONFIG_AT803X_PHY=y
|
||||
CONFIG_MARVELL_PHY=y
|
||||
CONFIG_SMSC_PHY=y
|
||||
CONFIG_BROADCOM_PHY=y
|
||||
CONFIG_ICPLUS_PHY=y
|
||||
CONFIG_REALTEK_PHY=y
|
||||
CONFIG_MARVELL_PHY=y
|
||||
CONFIG_MICREL_PHY=y
|
||||
CONFIG_FIXED_PHY=y
|
||||
CONFIG_REALTEK_PHY=y
|
||||
CONFIG_ROCKCHIP_PHY=y
|
||||
CONFIG_SMSC_PHY=y
|
||||
CONFIG_USB_PEGASUS=y
|
||||
CONFIG_USB_RTL8152=m
|
||||
CONFIG_USB_LAN78XX=m
|
||||
|
@ -288,29 +262,29 @@ CONFIG_USB_USBNET=y
|
|||
CONFIG_USB_NET_SMSC75XX=y
|
||||
CONFIG_USB_NET_SMSC95XX=y
|
||||
CONFIG_BRCMFMAC=m
|
||||
CONFIG_RT2X00=m
|
||||
CONFIG_RT2800USB=m
|
||||
CONFIG_MWIFIEX=m
|
||||
CONFIG_MWIFIEX_SDIO=m
|
||||
CONFIG_RT2X00=m
|
||||
CONFIG_RT2800USB=m
|
||||
CONFIG_INPUT_JOYDEV=y
|
||||
CONFIG_INPUT_EVDEV=y
|
||||
CONFIG_KEYBOARD_QT1070=m
|
||||
CONFIG_KEYBOARD_GPIO=y
|
||||
CONFIG_KEYBOARD_TEGRA=y
|
||||
CONFIG_KEYBOARD_SPEAR=y
|
||||
CONFIG_KEYBOARD_ST_KEYSCAN=y
|
||||
CONFIG_KEYBOARD_CROS_EC=m
|
||||
CONFIG_KEYBOARD_SAMSUNG=m
|
||||
CONFIG_KEYBOARD_ST_KEYSCAN=y
|
||||
CONFIG_KEYBOARD_SPEAR=y
|
||||
CONFIG_KEYBOARD_CROS_EC=m
|
||||
CONFIG_MOUSE_PS2_ELANTECH=y
|
||||
CONFIG_MOUSE_CYAPA=m
|
||||
CONFIG_MOUSE_ELAN_I2C=y
|
||||
CONFIG_INPUT_TOUCHSCREEN=y
|
||||
CONFIG_TOUCHSCREEN_ATMEL_MXT=m
|
||||
CONFIG_TOUCHSCREEN_MMS114=m
|
||||
CONFIG_TOUCHSCREEN_WM97XX=m
|
||||
CONFIG_TOUCHSCREEN_ST1232=m
|
||||
CONFIG_TOUCHSCREEN_STMPE=y
|
||||
CONFIG_TOUCHSCREEN_SUN4I=y
|
||||
CONFIG_TOUCHSCREEN_WM97XX=m
|
||||
CONFIG_INPUT_MISC=y
|
||||
CONFIG_INPUT_MAX77693_HAPTIC=m
|
||||
CONFIG_INPUT_MAX8997_HAPTIC=m
|
||||
|
@ -327,13 +301,12 @@ CONFIG_SERIAL_8250_DW=y
|
|||
CONFIG_SERIAL_8250_EM=y
|
||||
CONFIG_SERIAL_8250_MT6577=y
|
||||
CONFIG_SERIAL_8250_UNIPHIER=y
|
||||
CONFIG_SERIAL_OF_PLATFORM=y
|
||||
CONFIG_SERIAL_AMBA_PL011=y
|
||||
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
|
||||
CONFIG_SERIAL_ATMEL=y
|
||||
CONFIG_SERIAL_ATMEL_CONSOLE=y
|
||||
CONFIG_SERIAL_ATMEL_TTYAT=y
|
||||
CONFIG_SERIAL_BCM63XX=y
|
||||
CONFIG_SERIAL_BCM63XX_CONSOLE=y
|
||||
CONFIG_SERIAL_MESON=y
|
||||
CONFIG_SERIAL_MESON_CONSOLE=y
|
||||
CONFIG_SERIAL_SAMSUNG=y
|
||||
|
@ -345,15 +318,14 @@ CONFIG_SERIAL_IMX=y
|
|||
CONFIG_SERIAL_IMX_CONSOLE=y
|
||||
CONFIG_SERIAL_SH_SCI=y
|
||||
CONFIG_SERIAL_SH_SCI_NR_UARTS=20
|
||||
CONFIG_SERIAL_SH_SCI_CONSOLE=y
|
||||
CONFIG_SERIAL_SH_SCI_DMA=y
|
||||
CONFIG_SERIAL_MSM=y
|
||||
CONFIG_SERIAL_MSM_CONSOLE=y
|
||||
CONFIG_SERIAL_VT8500=y
|
||||
CONFIG_SERIAL_VT8500_CONSOLE=y
|
||||
CONFIG_SERIAL_OF_PLATFORM=y
|
||||
CONFIG_SERIAL_OMAP=y
|
||||
CONFIG_SERIAL_OMAP_CONSOLE=y
|
||||
CONFIG_SERIAL_BCM63XX=y
|
||||
CONFIG_SERIAL_BCM63XX_CONSOLE=y
|
||||
CONFIG_SERIAL_XILINX_PS_UART=y
|
||||
CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
|
||||
CONFIG_SERIAL_FSL_LPUART=y
|
||||
|
@ -365,12 +337,10 @@ CONFIG_SERIAL_ST_ASC_CONSOLE=y
|
|||
CONFIG_SERIAL_STM32=y
|
||||
CONFIG_SERIAL_STM32_CONSOLE=y
|
||||
CONFIG_SERIAL_DEV_BUS=y
|
||||
CONFIG_HVC_DRIVER=y
|
||||
CONFIG_VIRTIO_CONSOLE=y
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HW_RANDOM_ST=y
|
||||
CONFIG_I2C_CHARDEV=y
|
||||
CONFIG_I2C_DAVINCI=y
|
||||
CONFIG_I2C_MESON=y
|
||||
CONFIG_I2C_MUX=y
|
||||
CONFIG_I2C_ARB_GPIO_CHALLENGE=m
|
||||
CONFIG_I2C_MUX_PCA954x=y
|
||||
CONFIG_I2C_MUX_PINCTRL=y
|
||||
|
@ -378,12 +348,13 @@ CONFIG_I2C_DEMUX_PINCTRL=y
|
|||
CONFIG_I2C_AT91=m
|
||||
CONFIG_I2C_BCM2835=y
|
||||
CONFIG_I2C_CADENCE=y
|
||||
CONFIG_I2C_DAVINCI=y
|
||||
CONFIG_I2C_DESIGNWARE_PLATFORM=y
|
||||
CONFIG_I2C_DIGICOLOR=m
|
||||
CONFIG_I2C_EMEV2=m
|
||||
CONFIG_I2C_GPIO=m
|
||||
CONFIG_I2C_EXYNOS5=y
|
||||
CONFIG_I2C_IMX=y
|
||||
CONFIG_I2C_MESON=y
|
||||
CONFIG_I2C_MV64XXX=y
|
||||
CONFIG_I2C_RIIC=y
|
||||
CONFIG_I2C_RK3X=y
|
||||
|
@ -427,7 +398,6 @@ CONFIG_SPI_SPIDEV=y
|
|||
CONFIG_SPMI=y
|
||||
CONFIG_PINCTRL_AS3722=y
|
||||
CONFIG_PINCTRL_PALMAS=y
|
||||
CONFIG_PINCTRL_BCM2835=y
|
||||
CONFIG_PINCTRL_APQ8064=y
|
||||
CONFIG_PINCTRL_APQ8084=y
|
||||
CONFIG_PINCTRL_IPQ8064=y
|
||||
|
@ -437,25 +407,33 @@ CONFIG_PINCTRL_MSM8X74=y
|
|||
CONFIG_PINCTRL_MSM8916=y
|
||||
CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
|
||||
CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
|
||||
CONFIG_GPIO_GENERIC_PLATFORM=y
|
||||
CONFIG_GPIO_DAVINCI=y
|
||||
CONFIG_GPIO_DWAPB=y
|
||||
CONFIG_GPIO_EM=y
|
||||
CONFIG_GPIO_RCAR=y
|
||||
CONFIG_GPIO_SYSCON=y
|
||||
CONFIG_GPIO_UNIPHIER=y
|
||||
CONFIG_GPIO_XILINX=y
|
||||
CONFIG_GPIO_ZYNQ=y
|
||||
CONFIG_GPIO_PCA953X=y
|
||||
CONFIG_GPIO_PCA953X_IRQ=y
|
||||
CONFIG_GPIO_PCF857X=y
|
||||
CONFIG_GPIO_TWL4030=y
|
||||
CONFIG_GPIO_PALMAS=y
|
||||
CONFIG_GPIO_SYSCON=y
|
||||
CONFIG_GPIO_TPS6586X=y
|
||||
CONFIG_GPIO_TPS65910=y
|
||||
CONFIG_GPIO_TWL4030=y
|
||||
CONFIG_POWER_AVS=y
|
||||
CONFIG_ROCKCHIP_IODOMAIN=y
|
||||
CONFIG_POWER_RESET_AS3722=y
|
||||
CONFIG_POWER_RESET_GPIO=y
|
||||
CONFIG_POWER_RESET_GPIO_RESTART=y
|
||||
CONFIG_POWER_RESET_ST=y
|
||||
CONFIG_POWER_RESET_KEYSTONE=y
|
||||
CONFIG_POWER_RESET_RMOBILE=y
|
||||
CONFIG_BATTERY_ACT8945A=y
|
||||
CONFIG_BATTERY_CPCAP=m
|
||||
CONFIG_BATTERY_SBS=y
|
||||
CONFIG_AXP20X_POWER=m
|
||||
CONFIG_BATTERY_MAX17040=m
|
||||
CONFIG_BATTERY_MAX17042=m
|
||||
CONFIG_CHARGER_CPCAP=m
|
||||
|
@ -464,15 +442,6 @@ CONFIG_CHARGER_MAX77693=m
|
|||
CONFIG_CHARGER_MAX8997=m
|
||||
CONFIG_CHARGER_MAX8998=m
|
||||
CONFIG_CHARGER_TPS65090=y
|
||||
CONFIG_AXP20X_POWER=m
|
||||
CONFIG_POWER_RESET_AS3722=y
|
||||
CONFIG_POWER_RESET_GPIO=y
|
||||
CONFIG_POWER_RESET_GPIO_RESTART=y
|
||||
CONFIG_POWER_RESET_KEYSTONE=y
|
||||
CONFIG_POWER_RESET_RMOBILE=y
|
||||
CONFIG_POWER_RESET_ST=y
|
||||
CONFIG_POWER_AVS=y
|
||||
CONFIG_ROCKCHIP_IODOMAIN=y
|
||||
CONFIG_SENSORS_IIO_HWMON=y
|
||||
CONFIG_SENSORS_LM90=y
|
||||
CONFIG_SENSORS_LM95245=y
|
||||
|
@ -480,14 +449,12 @@ CONFIG_SENSORS_NTC_THERMISTOR=m
|
|||
CONFIG_SENSORS_PWM_FAN=m
|
||||
CONFIG_SENSORS_INA2XX=m
|
||||
CONFIG_CPU_THERMAL=y
|
||||
CONFIG_BCM2835_THERMAL=m
|
||||
CONFIG_BRCMSTB_THERMAL=m
|
||||
CONFIG_IMX_THERMAL=y
|
||||
CONFIG_ROCKCHIP_THERMAL=y
|
||||
CONFIG_RCAR_THERMAL=y
|
||||
CONFIG_ARMADA_THERMAL=y
|
||||
CONFIG_DAVINCI_WATCHDOG=m
|
||||
CONFIG_EXYNOS_THERMAL=m
|
||||
CONFIG_BCM2835_THERMAL=m
|
||||
CONFIG_BRCMSTB_THERMAL=m
|
||||
CONFIG_ST_THERMAL_MEMMAP=y
|
||||
CONFIG_WATCHDOG=y
|
||||
CONFIG_DA9063_WATCHDOG=m
|
||||
|
@ -495,20 +462,24 @@ CONFIG_XILINX_WATCHDOG=y
|
|||
CONFIG_ARM_SP805_WATCHDOG=y
|
||||
CONFIG_AT91SAM9X_WATCHDOG=y
|
||||
CONFIG_SAMA5D4_WATCHDOG=y
|
||||
CONFIG_DW_WATCHDOG=y
|
||||
CONFIG_DAVINCI_WATCHDOG=m
|
||||
CONFIG_ORION_WATCHDOG=y
|
||||
CONFIG_RN5T618_WATCHDOG=y
|
||||
CONFIG_ST_LPC_WATCHDOG=y
|
||||
CONFIG_SUNXI_WATCHDOG=y
|
||||
CONFIG_IMX2_WDT=y
|
||||
CONFIG_ST_LPC_WATCHDOG=y
|
||||
CONFIG_TEGRA_WATCHDOG=m
|
||||
CONFIG_MESON_WATCHDOG=y
|
||||
CONFIG_DW_WATCHDOG=y
|
||||
CONFIG_DIGICOLOR_WATCHDOG=y
|
||||
CONFIG_RENESAS_WDT=m
|
||||
CONFIG_BCM2835_WDT=y
|
||||
CONFIG_BCM47XX_WDT=y
|
||||
CONFIG_BCM7038_WDT=m
|
||||
CONFIG_BCM2835_WDT=y
|
||||
CONFIG_BCM_KONA_WDT=y
|
||||
CONFIG_BCM7038_WDT=m
|
||||
CONFIG_BCMA_HOST_SOC=y
|
||||
CONFIG_BCMA_DRIVER_GMAC_CMN=y
|
||||
CONFIG_BCMA_DRIVER_GPIO=y
|
||||
CONFIG_MFD_ACT8945A=y
|
||||
CONFIG_MFD_AS3711=y
|
||||
CONFIG_MFD_AS3722=y
|
||||
|
@ -516,7 +487,6 @@ CONFIG_MFD_ATMEL_FLEXCOM=y
|
|||
CONFIG_MFD_ATMEL_HLCDC=m
|
||||
CONFIG_MFD_BCM590XX=y
|
||||
CONFIG_MFD_AC100=y
|
||||
CONFIG_MFD_AXP20X=y
|
||||
CONFIG_MFD_AXP20X_I2C=y
|
||||
CONFIG_MFD_AXP20X_RSB=y
|
||||
CONFIG_MFD_CROS_EC=m
|
||||
|
@ -529,11 +499,11 @@ CONFIG_MFD_MAX77693=m
|
|||
CONFIG_MFD_MAX8907=y
|
||||
CONFIG_MFD_MAX8997=y
|
||||
CONFIG_MFD_MAX8998=y
|
||||
CONFIG_MFD_RK808=y
|
||||
CONFIG_MFD_CPCAP=y
|
||||
CONFIG_MFD_PM8XXX=y
|
||||
CONFIG_MFD_QCOM_RPM=y
|
||||
CONFIG_MFD_SPMI_PMIC=y
|
||||
CONFIG_MFD_RK808=y
|
||||
CONFIG_MFD_RN5T618=y
|
||||
CONFIG_MFD_SEC_CORE=y
|
||||
CONFIG_MFD_STMPE=y
|
||||
|
@ -543,10 +513,10 @@ CONFIG_MFD_TPS65217=y
|
|||
CONFIG_MFD_TPS65218=y
|
||||
CONFIG_MFD_TPS6586X=y
|
||||
CONFIG_MFD_TPS65910=y
|
||||
CONFIG_REGULATOR_ACT8945A=y
|
||||
CONFIG_REGULATOR_AB8500=y
|
||||
CONFIG_REGULATOR_ACT8865=y
|
||||
CONFIG_REGULATOR_ACT8945A=y
|
||||
CONFIG_REGULATOR_ANATOP=y
|
||||
CONFIG_REGULATOR_AB8500=y
|
||||
CONFIG_REGULATOR_AS3711=y
|
||||
CONFIG_REGULATOR_AS3722=y
|
||||
CONFIG_REGULATOR_AXP20X=y
|
||||
|
@ -554,10 +524,7 @@ CONFIG_REGULATOR_BCM590XX=y
|
|||
CONFIG_REGULATOR_CPCAP=y
|
||||
CONFIG_REGULATOR_DA9210=y
|
||||
CONFIG_REGULATOR_FAN53555=y
|
||||
CONFIG_REGULATOR_RK808=y
|
||||
CONFIG_REGULATOR_GPIO=y
|
||||
CONFIG_MFD_SYSCON=y
|
||||
CONFIG_POWER_RESET_SYSCON=y
|
||||
CONFIG_REGULATOR_LP872X=y
|
||||
CONFIG_REGULATOR_MAX14577=m
|
||||
CONFIG_REGULATOR_MAX8907=y
|
||||
|
@ -571,7 +538,8 @@ CONFIG_REGULATOR_PALMAS=y
|
|||
CONFIG_REGULATOR_PBIAS=y
|
||||
CONFIG_REGULATOR_PWM=y
|
||||
CONFIG_REGULATOR_QCOM_RPM=y
|
||||
CONFIG_REGULATOR_QCOM_SMD_RPM=y
|
||||
CONFIG_REGULATOR_QCOM_SMD_RPM=m
|
||||
CONFIG_REGULATOR_RK808=y
|
||||
CONFIG_REGULATOR_RN5T618=y
|
||||
CONFIG_REGULATOR_S2MPS11=y
|
||||
CONFIG_REGULATOR_S5M8767=y
|
||||
|
@ -592,18 +560,17 @@ CONFIG_MEDIA_CEC_SUPPORT=y
|
|||
CONFIG_MEDIA_CONTROLLER=y
|
||||
CONFIG_VIDEO_V4L2_SUBDEV_API=y
|
||||
CONFIG_MEDIA_USB_SUPPORT=y
|
||||
CONFIG_USB_VIDEO_CLASS=y
|
||||
CONFIG_USB_GSPCA=y
|
||||
CONFIG_USB_VIDEO_CLASS=m
|
||||
CONFIG_V4L_PLATFORM_DRIVERS=y
|
||||
CONFIG_SOC_CAMERA=m
|
||||
CONFIG_SOC_CAMERA_PLATFORM=m
|
||||
CONFIG_VIDEO_RCAR_VIN=m
|
||||
CONFIG_VIDEO_ATMEL_ISI=m
|
||||
CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS=m
|
||||
CONFIG_VIDEO_S5P_FIMC=m
|
||||
CONFIG_VIDEO_S5P_MIPI_CSIS=m
|
||||
CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
|
||||
CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
|
||||
CONFIG_VIDEO_RCAR_VIN=m
|
||||
CONFIG_VIDEO_ATMEL_ISI=m
|
||||
CONFIG_V4L_MEM2MEM_DRIVERS=y
|
||||
CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
|
||||
CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
|
||||
|
@ -614,19 +581,15 @@ CONFIG_VIDEO_STI_DELTA=m
|
|||
CONFIG_VIDEO_RENESAS_JPU=m
|
||||
CONFIG_VIDEO_RENESAS_VSP1=m
|
||||
CONFIG_V4L_TEST_DRIVERS=y
|
||||
CONFIG_VIDEO_VIVID=m
|
||||
CONFIG_CEC_PLATFORM_DRIVERS=y
|
||||
CONFIG_VIDEO_SAMSUNG_S5P_CEC=m
|
||||
# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
|
||||
CONFIG_VIDEO_ADV7180=m
|
||||
CONFIG_VIDEO_ML86V7667=m
|
||||
CONFIG_DRM=y
|
||||
CONFIG_DRM_I2C_ADV7511=m
|
||||
CONFIG_DRM_I2C_ADV7511_AUDIO=y
|
||||
# CONFIG_DRM_I2C_CH7006 is not set
|
||||
# CONFIG_DRM_I2C_SIL164 is not set
|
||||
CONFIG_DRM_DUMB_VGA_DAC=m
|
||||
CONFIG_DRM_NXP_PTN3460=m
|
||||
CONFIG_DRM_PARADE_PS8622=m
|
||||
CONFIG_DRM_NOUVEAU=m
|
||||
CONFIG_DRM_EXYNOS=m
|
||||
CONFIG_DRM_EXYNOS_FIMD=y
|
||||
|
@ -645,13 +608,18 @@ CONFIG_DRM_RCAR_LVDS=y
|
|||
CONFIG_DRM_SUN4I=m
|
||||
CONFIG_DRM_FSL_DCU=m
|
||||
CONFIG_DRM_TEGRA=y
|
||||
CONFIG_DRM_PANEL_SIMPLE=y
|
||||
CONFIG_DRM_PANEL_SAMSUNG_LD9040=m
|
||||
CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=m
|
||||
CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=m
|
||||
CONFIG_DRM_PANEL_SIMPLE=y
|
||||
CONFIG_DRM_DUMB_VGA_DAC=m
|
||||
CONFIG_DRM_NXP_PTN3460=m
|
||||
CONFIG_DRM_PARADE_PS8622=m
|
||||
CONFIG_DRM_SII9234=m
|
||||
CONFIG_DRM_I2C_ADV7511=m
|
||||
CONFIG_DRM_I2C_ADV7511_AUDIO=y
|
||||
CONFIG_DRM_STI=m
|
||||
CONFIG_DRM_VC4=y
|
||||
CONFIG_DRM_VC4=m
|
||||
CONFIG_DRM_ETNAVIV=m
|
||||
CONFIG_DRM_MXSFB=m
|
||||
CONFIG_FB_ARMCLCD=y
|
||||
|
@ -659,8 +627,6 @@ CONFIG_FB_EFI=y
|
|||
CONFIG_FB_WM8505=y
|
||||
CONFIG_FB_SH_MOBILE_LCDC=y
|
||||
CONFIG_FB_SIMPLE=y
|
||||
CONFIG_BACKLIGHT_LCD_SUPPORT=y
|
||||
CONFIG_BACKLIGHT_CLASS_DEVICE=y
|
||||
CONFIG_LCD_PLATFORM=m
|
||||
CONFIG_BACKLIGHT_PWM=y
|
||||
CONFIG_BACKLIGHT_AS3711=y
|
||||
|
@ -668,7 +634,6 @@ CONFIG_FRAMEBUFFER_CONSOLE=y
|
|||
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
|
||||
CONFIG_SOUND=m
|
||||
CONFIG_SND=m
|
||||
CONFIG_SND_DYNAMIC_MINORS=y
|
||||
CONFIG_SND_HDA_TEGRA=m
|
||||
CONFIG_SND_HDA_INPUT_BEEP=y
|
||||
CONFIG_SND_HDA_PATCH_LOADER=y
|
||||
|
@ -692,7 +657,7 @@ CONFIG_SND_SOC_SNOW=m
|
|||
CONFIG_SND_SOC_ODROID=m
|
||||
CONFIG_SND_SOC_SH4_FSI=m
|
||||
CONFIG_SND_SOC_RCAR=m
|
||||
CONFIG_SND_SIMPLE_SCU_CARD=m
|
||||
CONFIG_SND_SOC_STI=m
|
||||
CONFIG_SND_SUN4I_CODEC=m
|
||||
CONFIG_SND_SOC_TEGRA=m
|
||||
CONFIG_SND_SOC_TEGRA20_I2S=m
|
||||
|
@ -703,31 +668,25 @@ CONFIG_SND_SOC_TEGRA_WM8903=m
|
|||
CONFIG_SND_SOC_TEGRA_WM9712=m
|
||||
CONFIG_SND_SOC_TEGRA_TRIMSLICE=m
|
||||
CONFIG_SND_SOC_TEGRA_ALC5632=m
|
||||
CONFIG_SND_SOC_CPCAP=m
|
||||
CONFIG_SND_SOC_TEGRA_MAX98090=m
|
||||
CONFIG_SND_SOC_AK4642=m
|
||||
CONFIG_SND_SOC_CPCAP=m
|
||||
CONFIG_SND_SOC_SGTL5000=m
|
||||
CONFIG_SND_SOC_SPDIF=m
|
||||
CONFIG_SND_SOC_WM8978=m
|
||||
CONFIG_SND_SOC_STI=m
|
||||
CONFIG_SND_SOC_STI_SAS=m
|
||||
CONFIG_SND_SIMPLE_CARD=m
|
||||
CONFIG_SND_SOC_WM8978=m
|
||||
CONFIG_SND_SIMPLE_SCU_CARD=m
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_OTG=y
|
||||
CONFIG_USB_XHCI_HCD=y
|
||||
CONFIG_USB_XHCI_MVEBU=y
|
||||
CONFIG_USB_XHCI_RCAR=m
|
||||
CONFIG_USB_XHCI_TEGRA=m
|
||||
CONFIG_USB_EHCI_HCD=y
|
||||
CONFIG_USB_EHCI_MSM=m
|
||||
CONFIG_USB_EHCI_EXYNOS=y
|
||||
CONFIG_USB_EHCI_TEGRA=y
|
||||
CONFIG_USB_EHCI_HCD_STI=y
|
||||
CONFIG_USB_EHCI_HCD_PLATFORM=y
|
||||
CONFIG_USB_ISP1760=y
|
||||
CONFIG_USB_EHCI_TEGRA=y
|
||||
CONFIG_USB_EHCI_EXYNOS=y
|
||||
CONFIG_USB_OHCI_HCD=y
|
||||
CONFIG_USB_OHCI_HCD_STI=y
|
||||
CONFIG_USB_OHCI_HCD_PLATFORM=y
|
||||
CONFIG_USB_OHCI_EXYNOS=m
|
||||
CONFIG_USB_R8A66597_HCD=m
|
||||
CONFIG_USB_RENESAS_USBHS=m
|
||||
|
@ -746,18 +705,18 @@ CONFIG_USB_TI_CPPI41_DMA=y
|
|||
CONFIG_USB_TUSB_OMAP_DMA=y
|
||||
CONFIG_USB_DWC3=y
|
||||
CONFIG_USB_DWC2=y
|
||||
CONFIG_USB_HSIC_USB3503=y
|
||||
CONFIG_USB_CHIPIDEA=y
|
||||
CONFIG_USB_CHIPIDEA_UDC=y
|
||||
CONFIG_USB_CHIPIDEA_HOST=y
|
||||
CONFIG_USB_ISP1760=y
|
||||
CONFIG_USB_HSIC_USB3503=y
|
||||
CONFIG_AB8500_USB=y
|
||||
CONFIG_KEYSTONE_USB_PHY=y
|
||||
CONFIG_KEYSTONE_USB_PHY=m
|
||||
CONFIG_NOP_USB_XCEIV=m
|
||||
CONFIG_AM335X_PHY_USB=m
|
||||
CONFIG_TWL6030_USB=m
|
||||
CONFIG_USB_GPIO_VBUS=y
|
||||
CONFIG_USB_ISP1301=y
|
||||
CONFIG_USB_MSM_OTG=m
|
||||
CONFIG_USB_MXS_PHY=y
|
||||
CONFIG_USB_GADGET=y
|
||||
CONFIG_USB_FSL_USB2=y
|
||||
|
@ -793,21 +752,20 @@ CONFIG_MMC_SDHCI_OF_ESDHC=y
|
|||
CONFIG_MMC_SDHCI_ESDHC_IMX=y
|
||||
CONFIG_MMC_SDHCI_DOVE=y
|
||||
CONFIG_MMC_SDHCI_TEGRA=y
|
||||
CONFIG_MMC_SDHCI_S3C=y
|
||||
CONFIG_MMC_SDHCI_PXAV3=y
|
||||
CONFIG_MMC_SDHCI_SPEAR=y
|
||||
CONFIG_MMC_SDHCI_S3C=y
|
||||
CONFIG_MMC_SDHCI_S3C_DMA=y
|
||||
CONFIG_MMC_SDHCI_BCM_KONA=y
|
||||
CONFIG_MMC_MESON_MX_SDIO=y
|
||||
CONFIG_MMC_SDHCI_ST=y
|
||||
CONFIG_MMC_OMAP=y
|
||||
CONFIG_MMC_OMAP_HS=y
|
||||
CONFIG_MMC_ATMELMCI=y
|
||||
CONFIG_MMC_SDHCI_MSM=y
|
||||
CONFIG_MMC_MESON_MX_SDIO=y
|
||||
CONFIG_MMC_MVSDIO=y
|
||||
CONFIG_MMC_SDHI=y
|
||||
CONFIG_MMC_DW=y
|
||||
CONFIG_MMC_DW_PLTFM=y
|
||||
CONFIG_MMC_DW_EXYNOS=y
|
||||
CONFIG_MMC_DW_ROCKCHIP=y
|
||||
CONFIG_MMC_SH_MMCIF=y
|
||||
|
@ -847,94 +805,85 @@ CONFIG_RTC_DRV_MAX77686=y
|
|||
CONFIG_RTC_DRV_RK808=m
|
||||
CONFIG_RTC_DRV_RS5C372=m
|
||||
CONFIG_RTC_DRV_BQ32K=m
|
||||
CONFIG_RTC_DRV_PALMAS=y
|
||||
CONFIG_RTC_DRV_ST_LPC=y
|
||||
CONFIG_RTC_DRV_TWL4030=y
|
||||
CONFIG_RTC_DRV_PALMAS=y
|
||||
CONFIG_RTC_DRV_TPS6586X=y
|
||||
CONFIG_RTC_DRV_TPS65910=y
|
||||
CONFIG_RTC_DRV_S35390A=m
|
||||
CONFIG_RTC_DRV_RX8581=m
|
||||
CONFIG_RTC_DRV_EM3027=y
|
||||
CONFIG_RTC_DRV_S5M=m
|
||||
CONFIG_RTC_DRV_DA9063=m
|
||||
CONFIG_RTC_DRV_EFI=m
|
||||
CONFIG_RTC_DRV_DIGICOLOR=m
|
||||
CONFIG_RTC_DRV_S5M=m
|
||||
CONFIG_RTC_DRV_S3C=m
|
||||
CONFIG_RTC_DRV_PL031=y
|
||||
CONFIG_RTC_DRV_AT91RM9200=m
|
||||
CONFIG_RTC_DRV_AT91SAM9=m
|
||||
CONFIG_RTC_DRV_VT8500=y
|
||||
CONFIG_RTC_DRV_SUN6I=y
|
||||
CONFIG_RTC_DRV_SUNXI=y
|
||||
CONFIG_RTC_DRV_MV=y
|
||||
CONFIG_RTC_DRV_TEGRA=y
|
||||
CONFIG_RTC_DRV_ST_LPC=y
|
||||
CONFIG_RTC_DRV_CPCAP=m
|
||||
CONFIG_DMADEVICES=y
|
||||
CONFIG_DW_DMAC=y
|
||||
CONFIG_AT_HDMAC=y
|
||||
CONFIG_AT_XDMAC=y
|
||||
CONFIG_DMA_BCM2835=y
|
||||
CONFIG_DMA_SUN6I=y
|
||||
CONFIG_FSL_EDMA=y
|
||||
CONFIG_IMX_DMA=y
|
||||
CONFIG_IMX_SDMA=y
|
||||
CONFIG_MV_XOR=y
|
||||
CONFIG_MXS_DMA=y
|
||||
CONFIG_PL330_DMA=y
|
||||
CONFIG_SIRF_DMA=y
|
||||
CONFIG_STE_DMA40=y
|
||||
CONFIG_ST_FDMA=m
|
||||
CONFIG_TEGRA20_APB_DMA=y
|
||||
CONFIG_XILINX_DMA=y
|
||||
CONFIG_QCOM_BAM_DMA=y
|
||||
CONFIG_DW_DMAC=y
|
||||
CONFIG_SH_DMAE=y
|
||||
CONFIG_RCAR_DMAC=y
|
||||
CONFIG_RENESAS_USB_DMAC=m
|
||||
CONFIG_STE_DMA40=y
|
||||
CONFIG_SIRF_DMA=y
|
||||
CONFIG_TI_EDMA=y
|
||||
CONFIG_PL330_DMA=y
|
||||
CONFIG_IMX_SDMA=y
|
||||
CONFIG_IMX_DMA=y
|
||||
CONFIG_MXS_DMA=y
|
||||
CONFIG_DMA_BCM2835=y
|
||||
CONFIG_DMA_OMAP=y
|
||||
CONFIG_QCOM_BAM_DMA=y
|
||||
CONFIG_XILINX_DMA=y
|
||||
CONFIG_DMA_SUN6I=y
|
||||
CONFIG_ST_FDMA=m
|
||||
CONFIG_VIRTIO_PCI=y
|
||||
CONFIG_VIRTIO_MMIO=y
|
||||
CONFIG_STAGING=y
|
||||
CONFIG_SENSORS_ISL29018=y
|
||||
CONFIG_SENSORS_ISL29028=y
|
||||
CONFIG_MFD_NVEC=y
|
||||
CONFIG_KEYBOARD_NVEC=y
|
||||
CONFIG_SERIO_NVEC_PS2=y
|
||||
CONFIG_NVEC_POWER=y
|
||||
CONFIG_NVEC_PAZ00=y
|
||||
CONFIG_BCMA=y
|
||||
CONFIG_BCMA_HOST_SOC=y
|
||||
CONFIG_BCMA_DRIVER_GMAC_CMN=y
|
||||
CONFIG_BCMA_DRIVER_GPIO=y
|
||||
CONFIG_QCOM_GSBI=y
|
||||
CONFIG_QCOM_PM=y
|
||||
CONFIG_QCOM_SMEM=y
|
||||
CONFIG_QCOM_SMD_RPM=y
|
||||
CONFIG_QCOM_SMP2P=y
|
||||
CONFIG_QCOM_SMSM=y
|
||||
CONFIG_QCOM_WCNSS_CTRL=m
|
||||
CONFIG_ROCKCHIP_PM_DOMAINS=y
|
||||
CONFIG_COMMON_CLK_QCOM=y
|
||||
CONFIG_QCOM_CLK_RPM=y
|
||||
CONFIG_CHROME_PLATFORMS=y
|
||||
CONFIG_STAGING_BOARD=y
|
||||
CONFIG_CROS_EC_CHARDEV=m
|
||||
CONFIG_COMMON_CLK_MAX77686=y
|
||||
CONFIG_COMMON_CLK_RK808=m
|
||||
CONFIG_COMMON_CLK_S2MPS11=m
|
||||
CONFIG_COMMON_CLK_QCOM=y
|
||||
CONFIG_QCOM_CLK_RPM=y
|
||||
CONFIG_APQ_MMCC_8084=y
|
||||
CONFIG_MSM_GCC_8660=y
|
||||
CONFIG_MSM_MMCC_8960=y
|
||||
CONFIG_MSM_MMCC_8974=y
|
||||
CONFIG_HWSPINLOCK_QCOM=y
|
||||
CONFIG_BCM2835_MBOX=y
|
||||
CONFIG_ROCKCHIP_IOMMU=y
|
||||
CONFIG_TEGRA_IOMMU_GART=y
|
||||
CONFIG_TEGRA_IOMMU_SMMU=y
|
||||
CONFIG_REMOTEPROC=m
|
||||
CONFIG_ST_REMOTEPROC=m
|
||||
CONFIG_RPMSG_VIRTIO=m
|
||||
CONFIG_RASPBERRYPI_POWER=y
|
||||
CONFIG_QCOM_GSBI=y
|
||||
CONFIG_QCOM_PM=y
|
||||
CONFIG_QCOM_SMD_RPM=m
|
||||
CONFIG_QCOM_WCNSS_CTRL=m
|
||||
CONFIG_ROCKCHIP_PM_DOMAINS=y
|
||||
CONFIG_ARCH_TEGRA_2x_SOC=y
|
||||
CONFIG_ARCH_TEGRA_3x_SOC=y
|
||||
CONFIG_ARCH_TEGRA_114_SOC=y
|
||||
CONFIG_ARCH_TEGRA_124_SOC=y
|
||||
CONFIG_PM_DEVFREQ=y
|
||||
CONFIG_ARM_TEGRA_DEVFREQ=m
|
||||
CONFIG_MEMORY=y
|
||||
CONFIG_EXTCON=y
|
||||
CONFIG_TI_AEMIF=y
|
||||
CONFIG_IIO=y
|
||||
CONFIG_IIO_SW_TRIGGER=y
|
||||
|
@ -947,56 +896,54 @@ CONFIG_VF610_ADC=m
|
|||
CONFIG_XILINX_XADC=y
|
||||
CONFIG_MPU3050_I2C=y
|
||||
CONFIG_CM36651=m
|
||||
CONFIG_SENSORS_ISL29018=y
|
||||
CONFIG_SENSORS_ISL29028=y
|
||||
CONFIG_AK8975=y
|
||||
CONFIG_RASPBERRYPI_POWER=y
|
||||
CONFIG_IIO_HRTIMER_TRIGGER=y
|
||||
CONFIG_PWM=y
|
||||
CONFIG_PWM_ATMEL=m
|
||||
CONFIG_PWM_ATMEL_HLCDC_PWM=m
|
||||
CONFIG_PWM_ATMEL_TCB=m
|
||||
CONFIG_PWM_BCM2835=y
|
||||
CONFIG_PWM_BRCMSTB=m
|
||||
CONFIG_PWM_FSL_FTM=m
|
||||
CONFIG_PWM_MESON=m
|
||||
CONFIG_PWM_RCAR=m
|
||||
CONFIG_PWM_RENESAS_TPU=y
|
||||
CONFIG_PWM_ROCKCHIP=m
|
||||
CONFIG_PWM_SAMSUNG=m
|
||||
CONFIG_PWM_STI=y
|
||||
CONFIG_PWM_SUN4I=y
|
||||
CONFIG_PWM_TEGRA=y
|
||||
CONFIG_PWM_VT8500=y
|
||||
CONFIG_KEYSTONE_IRQ=y
|
||||
CONFIG_PHY_SUN4I_USB=y
|
||||
CONFIG_PHY_SUN9I_USB=y
|
||||
CONFIG_PHY_HIX5HD2_SATA=y
|
||||
CONFIG_E1000E=y
|
||||
CONFIG_PWM_STI=y
|
||||
CONFIG_PWM_BCM2835=y
|
||||
CONFIG_PWM_BRCMSTB=m
|
||||
CONFIG_PHY_BERLIN_SATA=y
|
||||
CONFIG_PHY_BERLIN_USB=y
|
||||
CONFIG_PHY_CPCAP_USB=m
|
||||
CONFIG_PHY_QCOM_APQ8064_SATA=m
|
||||
CONFIG_PHY_RCAR_GEN2=m
|
||||
CONFIG_PHY_ROCKCHIP_DP=m
|
||||
CONFIG_PHY_ROCKCHIP_USB=y
|
||||
CONFIG_PHY_SAMSUNG_USB2=m
|
||||
CONFIG_PHY_MIPHY28LP=y
|
||||
CONFIG_PHY_STIH407_USB=y
|
||||
CONFIG_PHY_STM32_USBPHYC=y
|
||||
CONFIG_PHY_TEGRA_XUSB=y
|
||||
CONFIG_PHY_DM816X_USB=m
|
||||
CONFIG_OMAP_USB2=y
|
||||
CONFIG_TI_PIPE3=y
|
||||
CONFIG_TWL4030_USB=m
|
||||
CONFIG_PHY_BERLIN_USB=y
|
||||
CONFIG_PHY_CPCAP_USB=m
|
||||
CONFIG_PHY_BERLIN_SATA=y
|
||||
CONFIG_PHY_ROCKCHIP_DP=m
|
||||
CONFIG_PHY_ROCKCHIP_USB=y
|
||||
CONFIG_PHY_QCOM_APQ8064_SATA=m
|
||||
CONFIG_PHY_MIPHY28LP=y
|
||||
CONFIG_PHY_RCAR_GEN2=m
|
||||
CONFIG_PHY_STIH407_USB=y
|
||||
CONFIG_PHY_STM32_USBPHYC=y
|
||||
CONFIG_PHY_SUN4I_USB=y
|
||||
CONFIG_PHY_SUN9I_USB=y
|
||||
CONFIG_PHY_SAMSUNG_USB2=m
|
||||
CONFIG_PHY_TEGRA_XUSB=y
|
||||
CONFIG_PHY_BRCM_SATA=y
|
||||
CONFIG_NVMEM=y
|
||||
CONFIG_NVMEM_IMX_OCOTP=y
|
||||
CONFIG_NVMEM_SUNXI_SID=y
|
||||
CONFIG_NVMEM_VF610_OCOTP=y
|
||||
CONFIG_BCM2835_MBOX=y
|
||||
CONFIG_RASPBERRYPI_FIRMWARE=y
|
||||
CONFIG_EFI_VARS=m
|
||||
CONFIG_EFI_CAPSULE_LOADER=m
|
||||
CONFIG_BCM47XX_NVRAM=y
|
||||
CONFIG_BCM47XX_SPROM=y
|
||||
CONFIG_EFI_VARS=m
|
||||
CONFIG_EFI_CAPSULE_LOADER=m
|
||||
CONFIG_EXT4_FS=y
|
||||
CONFIG_AUTOFS4_FS=y
|
||||
CONFIG_MSDOS_FS=y
|
||||
|
@ -1004,7 +951,6 @@ CONFIG_VFAT_FS=y
|
|||
CONFIG_NTFS_FS=y
|
||||
CONFIG_TMPFS_POSIX_ACL=y
|
||||
CONFIG_UBIFS_FS=y
|
||||
CONFIG_TMPFS=y
|
||||
CONFIG_SQUASHFS=y
|
||||
CONFIG_SQUASHFS_LZO=y
|
||||
CONFIG_SQUASHFS_XZ=y
|
||||
|
@ -1020,13 +966,7 @@ CONFIG_NLS_CODEPAGE_437=y
|
|||
CONFIG_NLS_ISO8859_1=y
|
||||
CONFIG_NLS_UTF8=y
|
||||
CONFIG_PRINTK_TIME=y
|
||||
CONFIG_DEBUG_FS=y
|
||||
CONFIG_MAGIC_SYSRQ=y
|
||||
CONFIG_LOCKUP_DETECTOR=y
|
||||
CONFIG_CPUFREQ_DT=y
|
||||
CONFIG_KEYSTONE_IRQ=y
|
||||
CONFIG_HW_RANDOM=y
|
||||
CONFIG_HW_RANDOM_ST=y
|
||||
CONFIG_CRYPTO_USER=m
|
||||
CONFIG_CRYPTO_USER_API_HASH=m
|
||||
CONFIG_CRYPTO_USER_API_SKCIPHER=m
|
||||
|
@ -1035,27 +975,19 @@ CONFIG_CRYPTO_USER_API_AEAD=m
|
|||
CONFIG_CRYPTO_DEV_MARVELL_CESA=m
|
||||
CONFIG_CRYPTO_DEV_EXYNOS_RNG=m
|
||||
CONFIG_CRYPTO_DEV_S5P=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_AES=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_TDES=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_SHA=m
|
||||
CONFIG_CRYPTO_DEV_SUN4I_SS=m
|
||||
CONFIG_CRYPTO_DEV_ROCKCHIP=m
|
||||
CONFIG_ARM_CRYPTO=y
|
||||
CONFIG_CRYPTO_SHA1_ARM=m
|
||||
CONFIG_CRYPTO_SHA1_ARM_NEON=m
|
||||
CONFIG_CRYPTO_SHA1_ARM_CE=m
|
||||
CONFIG_CRYPTO_SHA2_ARM_CE=m
|
||||
CONFIG_CRYPTO_SHA256_ARM=m
|
||||
CONFIG_CRYPTO_SHA512_ARM=m
|
||||
CONFIG_CRYPTO_AES_ARM=m
|
||||
CONFIG_CRYPTO_AES_ARM_BS=m
|
||||
CONFIG_CRYPTO_AES_ARM_CE=m
|
||||
CONFIG_CRYPTO_CHACHA20_NEON=m
|
||||
CONFIG_CRYPTO_CRC32_ARM_CE=m
|
||||
CONFIG_CRYPTO_CRCT10DIF_ARM_CE=m
|
||||
CONFIG_CRYPTO_GHASH_ARM_CE=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_AES=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_TDES=m
|
||||
CONFIG_CRYPTO_DEV_ATMEL_SHA=m
|
||||
CONFIG_VIDEO_VIVID=m
|
||||
CONFIG_VIRTIO=y
|
||||
CONFIG_VIRTIO_PCI=y
|
||||
CONFIG_VIRTIO_PCI_LEGACY=y
|
||||
CONFIG_VIRTIO_MMIO=y
|
||||
CONFIG_CRYPTO_CRC32_ARM_CE=m
|
||||
CONFIG_CRYPTO_CHACHA20_NEON=m
|
||||
|
|
|
@ -272,9 +272,11 @@
|
|||
* Allocate stack space to store 128 bytes worth of tweaks. For
|
||||
* performance, this space is aligned to a 16-byte boundary so that we
|
||||
* can use the load/store instructions that declare 16-byte alignment.
|
||||
* For Thumb2 compatibility, don't do the 'bic' directly on 'sp'.
|
||||
*/
|
||||
sub sp, #128
|
||||
bic sp, #0xf
|
||||
sub r12, sp, #128
|
||||
bic r12, #0xf
|
||||
mov sp, r12
|
||||
|
||||
.if \n == 64
|
||||
// Load first tweak
|
||||
|
|
|
@ -1 +1,4 @@
|
|||
obj-$(CONFIG_TRUSTED_FOUNDATIONS) += trusted_foundations.o
|
||||
|
||||
# tf_generic_smc() fails to build with -fsanitize-coverage=trace-pc
|
||||
KCOV_INSTRUMENT := n
|
||||
|
|
|
@ -177,7 +177,7 @@ M_CLASS(streq r3, [r12, #PMSAv8_MAIR1])
|
|||
bic r0, r0, #CR_I
|
||||
#endif
|
||||
mcr p15, 0, r0, c1, c0, 0 @ write control reg
|
||||
isb
|
||||
instr_sync
|
||||
#elif defined (CONFIG_CPU_V7M)
|
||||
#ifdef CONFIG_ARM_MPU
|
||||
ldreq r3, [r12, MPU_CTRL]
|
||||
|
|
|
@ -338,6 +338,7 @@ static struct vm_area_struct gate_vma = {
|
|||
|
||||
static int __init gate_vma_init(void)
|
||||
{
|
||||
vma_init(&gate_vma, NULL);
|
||||
gate_vma.vm_page_prot = PAGE_READONLY_EXEC;
|
||||
return 0;
|
||||
}
|
||||
|
|
|
@ -20,6 +20,7 @@ config ARCH_BCM_IPROC
|
|||
select GPIOLIB
|
||||
select ARM_AMBA
|
||||
select PINCTRL
|
||||
select PCI_DOMAINS if PCI
|
||||
help
|
||||
This enables support for systems based on Broadcom IPROC architected SoCs.
|
||||
The IPROC complex contains one or more ARM CPUs along with common
|
||||
|
|
|
@ -774,7 +774,7 @@ static struct gpiod_lookup_table mmc_gpios_table = {
|
|||
GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
|
||||
GPIO_ACTIVE_LOW),
|
||||
GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
|
||||
GPIO_ACTIVE_LOW),
|
||||
GPIO_ACTIVE_HIGH),
|
||||
},
|
||||
};
|
||||
|
||||
|
|
|
@ -109,6 +109,45 @@ void omap5_erratum_workaround_801819(void)
|
|||
static inline void omap5_erratum_workaround_801819(void) { }
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR
|
||||
/*
|
||||
* Configure ACR and enable ACTLR[0] (Enable invalidates of BTB with
|
||||
* ICIALLU) to activate the workaround for secondary Core.
|
||||
* NOTE: it is assumed that the primary core's configuration is done
|
||||
* by the boot loader (kernel will detect a misconfiguration and complain
|
||||
* if this is not done).
|
||||
*
|
||||
* In General Purpose(GP) devices, ACR bit settings can only be done
|
||||
* by ROM code in "secure world" using the smc call and there is no
|
||||
* option to update the "firmware" on such devices. This also works for
|
||||
* High security(HS) devices, as a backup option in case the
|
||||
* "update" is not done in the "security firmware".
|
||||
*/
|
||||
static void omap5_secondary_harden_predictor(void)
|
||||
{
|
||||
u32 acr, acr_mask;
|
||||
|
||||
asm volatile ("mrc p15, 0, %0, c1, c0, 1" : "=r" (acr));
|
||||
|
||||
/*
|
||||
* ACTLR[0] (Enable invalidates of BTB with ICIALLU)
|
||||
*/
|
||||
acr_mask = BIT(0);
|
||||
|
||||
/* Do we already have it done.. if yes, skip expensive smc */
|
||||
if ((acr & acr_mask) == acr_mask)
|
||||
return;
|
||||
|
||||
acr |= acr_mask;
|
||||
omap_smc1(OMAP5_DRA7_MON_SET_ACR_INDEX, acr);
|
||||
|
||||
pr_debug("%s: ARM ACR setup for CVE_2017_5715 applied on CPU%d\n",
|
||||
__func__, smp_processor_id());
|
||||
}
|
||||
#else
|
||||
static inline void omap5_secondary_harden_predictor(void) { }
|
||||
#endif
|
||||
|
||||
static void omap4_secondary_init(unsigned int cpu)
|
||||
{
|
||||
/*
|
||||
|
@ -131,6 +170,8 @@ static void omap4_secondary_init(unsigned int cpu)
|
|||
set_cntfreq();
|
||||
/* Configure ACR to disable streaming WA for 801819 */
|
||||
omap5_erratum_workaround_801819();
|
||||
/* Enable ACR to allow for ICUALLU workaround */
|
||||
omap5_secondary_harden_predictor();
|
||||
}
|
||||
|
||||
/*
|
||||
|
|
|
@ -185,7 +185,7 @@ static int pxa_irq_suspend(void)
|
|||
{
|
||||
int i;
|
||||
|
||||
for (i = 0; i < pxa_internal_irq_nr / 32; i++) {
|
||||
for (i = 0; i < DIV_ROUND_UP(pxa_internal_irq_nr, 32); i++) {
|
||||
void __iomem *base = irq_base(i);
|
||||
|
||||
saved_icmr[i] = __raw_readl(base + ICMR);
|
||||
|
@ -204,7 +204,7 @@ static void pxa_irq_resume(void)
|
|||
{
|
||||
int i;
|
||||
|
||||
for (i = 0; i < pxa_internal_irq_nr / 32; i++) {
|
||||
for (i = 0; i < DIV_ROUND_UP(pxa_internal_irq_nr, 32); i++) {
|
||||
void __iomem *base = irq_base(i);
|
||||
|
||||
__raw_writel(saved_icmr[i], base + ICMR);
|
||||
|
|
|
@ -237,8 +237,8 @@ static void ecard_init_pgtables(struct mm_struct *mm)
|
|||
|
||||
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
|
||||
|
||||
vma_init(&vma, mm);
|
||||
vma.vm_flags = VM_EXEC;
|
||||
vma.vm_mm = mm;
|
||||
|
||||
flush_tlb_range(&vma, IO_START, IO_START + IO_SIZE);
|
||||
flush_tlb_range(&vma, EASI_START, EASI_START + EASI_SIZE);
|
||||
|
|
|
@ -10,6 +10,7 @@ menuconfig ARCH_SOCFPGA
|
|||
select HAVE_ARM_SCU
|
||||
select HAVE_ARM_TWD if SMP
|
||||
select MFD_SYSCON
|
||||
select PCI_DOMAINS if PCI
|
||||
|
||||
if ARCH_SOCFPGA
|
||||
config SOCFPGA_SUSPEND
|
||||
|
|
|
@ -736,20 +736,29 @@ static int __mark_rodata_ro(void *unused)
|
|||
return 0;
|
||||
}
|
||||
|
||||
static int kernel_set_to_readonly __read_mostly;
|
||||
|
||||
void mark_rodata_ro(void)
|
||||
{
|
||||
kernel_set_to_readonly = 1;
|
||||
stop_machine(__mark_rodata_ro, NULL, NULL);
|
||||
debug_checkwx();
|
||||
}
|
||||
|
||||
void set_kernel_text_rw(void)
|
||||
{
|
||||
if (!kernel_set_to_readonly)
|
||||
return;
|
||||
|
||||
set_section_perms(ro_perms, ARRAY_SIZE(ro_perms), false,
|
||||
current->active_mm);
|
||||
}
|
||||
|
||||
void set_kernel_text_ro(void)
|
||||
{
|
||||
if (!kernel_set_to_readonly)
|
||||
return;
|
||||
|
||||
set_section_perms(ro_perms, ARRAY_SIZE(ro_perms), true,
|
||||
current->active_mm);
|
||||
}
|
||||
|
|
|
@ -1844,7 +1844,7 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
|
|||
/* there are 2 passes here */
|
||||
bpf_jit_dump(prog->len, image_size, 2, ctx.target);
|
||||
|
||||
set_memory_ro((unsigned long)header, header->pages);
|
||||
bpf_jit_binary_lock_ro(header);
|
||||
prog->bpf_func = (void *)ctx.target;
|
||||
prog->jited = 1;
|
||||
prog->jited_len = image_size;
|
||||
|
|
|
@ -10,7 +10,7 @@
|
|||
#
|
||||
# Copyright (C) 1995-2001 by Russell King
|
||||
|
||||
LDFLAGS_vmlinux :=-p --no-undefined -X
|
||||
LDFLAGS_vmlinux :=--no-undefined -X
|
||||
CPPFLAGS_vmlinux.lds = -DTEXT_OFFSET=$(TEXT_OFFSET)
|
||||
GZFLAGS :=-9
|
||||
|
||||
|
@ -60,15 +60,15 @@ ifeq ($(CONFIG_CPU_BIG_ENDIAN), y)
|
|||
KBUILD_CPPFLAGS += -mbig-endian
|
||||
CHECKFLAGS += -D__AARCH64EB__
|
||||
AS += -EB
|
||||
LD += -EB
|
||||
LDFLAGS += -maarch64linuxb
|
||||
# We must use the linux target here, since distributions don't tend to package
|
||||
# the ELF linker scripts with binutils, and this results in a build failure.
|
||||
LDFLAGS += -EB -maarch64linuxb
|
||||
UTS_MACHINE := aarch64_be
|
||||
else
|
||||
KBUILD_CPPFLAGS += -mlittle-endian
|
||||
CHECKFLAGS += -D__AARCH64EL__
|
||||
AS += -EL
|
||||
LD += -EL
|
||||
LDFLAGS += -maarch64linux
|
||||
LDFLAGS += -EL -maarch64linux # See comment above
|
||||
UTS_MACHINE := aarch64
|
||||
endif
|
||||
|
||||
|
|
|
@ -309,8 +309,7 @@
|
|||
interrupts = <0 99 4>;
|
||||
resets = <&rst SPIM0_RESET>;
|
||||
reg-io-width = <4>;
|
||||
num-chipselect = <4>;
|
||||
bus-num = <0>;
|
||||
num-cs = <4>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
|
@ -322,8 +321,7 @@
|
|||
interrupts = <0 100 4>;
|
||||
resets = <&rst SPIM1_RESET>;
|
||||
reg-io-width = <4>;
|
||||
num-chipselect = <4>;
|
||||
bus-num = <0>;
|
||||
num-cs = <4>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
|
|
|
@ -66,9 +66,22 @@
|
|||
|
||||
ðmac {
|
||||
status = "okay";
|
||||
phy-mode = "rgmii";
|
||||
pinctrl-0 = <ð_rgmii_y_pins>;
|
||||
pinctrl-names = "default";
|
||||
phy-handle = <ð_phy0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
mdio {
|
||||
compatible = "snps,dwmac-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
eth_phy0: ethernet-phy@0 {
|
||||
/* Realtek RTL8211F (0x001cc916) */
|
||||
reg = <0>;
|
||||
eee-broken-1000t;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart_A {
|
||||
|
|
|
@ -132,7 +132,7 @@
|
|||
|
||||
sd_emmc_b: sd@5000 {
|
||||
compatible = "amlogic,meson-axg-mmc";
|
||||
reg = <0x0 0x5000 0x0 0x2000>;
|
||||
reg = <0x0 0x5000 0x0 0x800>;
|
||||
interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "disabled";
|
||||
clocks = <&clkc CLKID_SD_EMMC_B>,
|
||||
|
@ -144,7 +144,7 @@
|
|||
|
||||
sd_emmc_c: mmc@7000 {
|
||||
compatible = "amlogic,meson-axg-mmc";
|
||||
reg = <0x0 0x7000 0x0 0x2000>;
|
||||
reg = <0x0 0x7000 0x0 0x800>;
|
||||
interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "disabled";
|
||||
clocks = <&clkc CLKID_SD_EMMC_C>,
|
||||
|
|
|
@ -35,6 +35,12 @@
|
|||
no-map;
|
||||
};
|
||||
|
||||
/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
|
||||
secmon_reserved_alt: secmon@5000000 {
|
||||
reg = <0x0 0x05000000 0x0 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
linux,cma {
|
||||
compatible = "shared-dma-pool";
|
||||
reusable;
|
||||
|
@ -457,21 +463,21 @@
|
|||
|
||||
sd_emmc_a: mmc@70000 {
|
||||
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
|
||||
reg = <0x0 0x70000 0x0 0x2000>;
|
||||
reg = <0x0 0x70000 0x0 0x800>;
|
||||
interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
sd_emmc_b: mmc@72000 {
|
||||
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
|
||||
reg = <0x0 0x72000 0x0 0x2000>;
|
||||
reg = <0x0 0x72000 0x0 0x800>;
|
||||
interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
sd_emmc_c: mmc@74000 {
|
||||
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
|
||||
reg = <0x0 0x74000 0x0 0x2000>;
|
||||
reg = <0x0 0x74000 0x0 0x800>;
|
||||
interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
|
@ -6,7 +6,7 @@
|
|||
|
||||
&apb {
|
||||
mali: gpu@c0000 {
|
||||
compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
|
||||
compatible = "amlogic,meson-gxl-mali", "arm,mali-450";
|
||||
reg = <0x0 0xc0000 0x0 0x40000>;
|
||||
interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
|
||||
|
|
|
@ -234,9 +234,6 @@
|
|||
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
sd-uhs-sdr12;
|
||||
sd-uhs-sdr25;
|
||||
sd-uhs-sdr50;
|
||||
max-frequency = <100000000>;
|
||||
disable-wp;
|
||||
|
||||
|
|
|
@ -189,3 +189,10 @@
|
|||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_phy0 {
|
||||
/*
|
||||
* HDMI_5V is also used as supply for the USB VBUS.
|
||||
*/
|
||||
phy-supply = <&hdmi_5v>;
|
||||
};
|
||||
|
|
Some files were not shown because too many files have changed in this diff Show more
Loading…
Reference in a new issue